Pipeline hydraulic transport is a highly efficient and low energy-consumption method for transporting solids and is commonly used for tailing slurry transport in the mining industry.Erosion wear(EW)remains the main ca...Pipeline hydraulic transport is a highly efficient and low energy-consumption method for transporting solids and is commonly used for tailing slurry transport in the mining industry.Erosion wear(EW)remains the main cause of failure in tailings slurry pipeline systems,particularly at bends.EW is a complex phenomenon influenced by numerous factors,but research in this area has been limited.This study performs numerical simulations of slurry transport at the bend by combining computational fluid dynamics and fluid particle tracking using a wear model.Based on the validation of the feasibility of the model,this work focuses on the effects of coupled inlet velocity(IV)ranging from 1.5 to 3.0 m·s^(-1),particle size(PS)ranging from 50 to 650μm,and bend angle(BA)ranging from 45°to 90°on EW at the bend in terms of particle kinetic energy and incidence angle.The results show that the maximum EW rate of the slurry at the bend increases exponentially with IV and PS and first increases and then decreases with the increase in BA with the inflection point at 60°within these parameter ranges.Further comprehensive analysis reveals that the sensitivity level of the three factors to the maximum EW rate is PS>IV>BA,and when IV is 3.0 m/s,PS is 650μm,and BA is 60°,the bend EW is the most severe,and the maximum EW rate is 5.68×10^(-6)kg·m^(-2)·s^(-1).In addition,When PS is below or equal to 450μm,the maximum EW position is mainly at the outlet of the bend.When PS is greater than 450μm,the maximum EW position shifts toward the center of the bend with the increase in BA.Therefore,EW at the bend can be reduced in practice by reducing IV as much as possible and using small particles.展开更多
The disposal of filtered tailings in high dry stacks can induce particle breakage,changing the material's behaviour during the structure's lifetime.The grading changes influence material properties at the crit...The disposal of filtered tailings in high dry stacks can induce particle breakage,changing the material's behaviour during the structure's lifetime.The grading changes influence material properties at the critical state,and this is not mature for intermediate artificial soils(tailings)in a broad range of confining pressures.In this paper,it aims to describe the behaviour of iron ore tailings in a spectrum of confining pressures broader than the reported in previous studies.A series of consolidated drained(CD)triaxial tests was carried out with confining pressures ranging from 0.075 MPa to 120 MPa.These results show that the amount of breakage plays an essential role in the response of iron ore tailings.The existence of curved critical state line(CSL)in both specific volume(ν)-logarithm of mean effective stress(p′)and deviatoric stress(q)-mean effective stress(p′)planes,and different responses in the deviatoric stress-axial strain-volumetric strain curves were verified.An inverse S-shaped equation was proposed to represent the silty-sandy tailings'behaviour up to high pressures onν-lnp′plane.The proposed equation provides a basis for enhancing constitutive models and considers the evolution of the grading up to severe loading conditions.The adjustment considered three regions with different responses associated with particle breakage at different pressure levels.展开更多
The tell tail is usually placed on the triangular sail to display the running state of the air flow on the sail surface.It is of great significance to make accurate judgement on the drift of the tell tail of the sailb...The tell tail is usually placed on the triangular sail to display the running state of the air flow on the sail surface.It is of great significance to make accurate judgement on the drift of the tell tail of the sailboat during sailing for the best sailing effect.Normally it is difficult for sailors to keep an eye for a long time on the tell sail for accurate judging its changes,affected by strong sunlight and visual fatigue.In this case,we adopt computer vision technology in hope of helping the sailors judge the changes of the tell tail in ease with ease.This paper proposes for the first time a method to classify sailboat tell tails based on deep learning and an expert guidance system,supported by a sailboat tell tail classification data set on the expert guidance system of interpreting the tell tails states in different sea wind conditions,including the feature extraction performance.Considering the expression capabilities that vary with the computational features in different visual tasks,the paper focuses on five tell tail computing features,which are recoded by an automatic encoder and classified by a SVM classifier.All experimental samples were randomly divided into five groups,and four groups were selected from each group as the training set to train the classifier.The remaining one group was used as the test set for testing.The highest resolution value of the ResNet network was 80.26%.To achieve better operational results on the basis of deep computing features obtained through the ResNet network in the experiments.The method can be used to assist the sailors in making better judgement about the tell tail changes during sailing.展开更多
Polypropylene(PP)fiber-reinforced cement-based tailings backfill(FRCTB)is a green compound material with superior crack resistance and has good prospects for application in underground mining.However,FRCTB exhibits su...Polypropylene(PP)fiber-reinforced cement-based tailings backfill(FRCTB)is a green compound material with superior crack resistance and has good prospects for application in underground mining.However,FRCTB exhibits susceptibility to dynamic events,such as impact ground pressure and blast vibrations.This paper investigates the energy and crack distribution behavior of FRCTB under dynamic impact,considering the height/diameter(H/D)effect.Split Hopkinson pressure bar,industrial computed tomography scan,and scanning electron microscopy(SEM)experiments were carried out on six types of FRCTB.Laboratory outcomes confirmed fiber aggregation at the bottom of specimens.When H/D was less than 0.8,the proportion of PP fibers distributed along theθangle direction of80°-90°increased.For the total energy,all samples presented similar energy absorption,reflectance,and transmittance.However,a rise in H/D may cause a rise in the energy absorption rate of FRCTB during the peak phase.A positive correlation existed between the average strain rate and absorbed energy per unit volume.The increase in H/D resulted in a decreased crack volume fraction of FRCTB.When the H/D was greater than or equal to 0.7,the maximum crack volume fraction of FRCTB was observed close to the incidence plane.Radial cracks were present only in the FRCTB with an H/D ratio of 0.5.Samples with H/D ratios of 0.5 and 0.6 showed similar distributions of weakly and heavily damaged areas.PP fibers can limit the emergence and expansion of cracks by influencing their path.SEM observations revealed considerable differences in the bonding strengths between fibers and the FRCTB.Fibers that adhered particularly well to the substrate were attracted together with the hydration products adhering to surfaces.These results show that FRCTB is promising as a sustainable and green backfill for determining the design properties of mining with backfill.展开更多
Cemented paste backfill(CPB)is a key technology for green mining in metal mines,in which tailings thickening comprises the primary link of CPB technology.However,difficult flocculation and substandard concentrations o...Cemented paste backfill(CPB)is a key technology for green mining in metal mines,in which tailings thickening comprises the primary link of CPB technology.However,difficult flocculation and substandard concentrations of thickened tailings often occur.The rheological properties and concentration evolution in the thickened tailings remain unclear.Moreover,traditional indoor thickening experiments have yet to quantitatively characterize their rheological properties.An experiment of flocculation condition optimization based on the Box-Behnken design(BBD)was performed in the study,and the two response values were investigated:concentration and the mean weighted chord length(MWCL)of flocs.Thus,optimal flocculation conditions were obtained.In addition,the rheological properties and concentration evolution of different flocculant dosages and ultrafine tailing contents under shear,compression,and compression-shear coupling experimental conditions were tested and compared.The results show that the shear yield stress under compression and compression-shear coupling increases with the growth of compressive yield stress,while the shear yield stress increases slightly under shear.The order of shear yield stress from low to high under different thickening conditions is shear,compression,and compression-shear coupling.Under compression and compression-shear coupling,the concentration first rapidly increases with the growth of compressive yield stress and then slowly increases,while concentration increases slightly under shear.The order of concentration from low to high under different thickening conditions is shear,compression,and compression-shear coupling.Finally,the evolution mechanism of the flocs and drainage channels during the thickening of the thickened tailings under different experimental conditions was revealed.展开更多
This paper discusses a queueing system with a retrial orbit and batch service, in which the quantity of customers’ rooms in the queue is finite and the space of retrial orbit is infinite. When the server starts servi...This paper discusses a queueing system with a retrial orbit and batch service, in which the quantity of customers’ rooms in the queue is finite and the space of retrial orbit is infinite. When the server starts serving, it serves all customers in the queue in a single batch, which is the so-called batch service. If a new customer or a retrial customer finds all the customers’ rooms are occupied, he will decide whether or not to join the retrial orbit. By using the censoring technique and the matrix analysis method, we first obtain the decay function of the stationary distribution for the quantity of customers in the retrial orbit and the quantity of customers in the queue. Then based on the form of decay rate function and the Karamata Tauberian theorem, we finally get the exact tail asymptotics of the stationary distribution.展开更多
The aim of this investigation was to prepare geopolymeric precursor from vanadium tailing(VT)by thermal activation and modification.For activation,a homogeneous blend of VT and sodium hydroxide was calcinated at an el...The aim of this investigation was to prepare geopolymeric precursor from vanadium tailing(VT)by thermal activation and modification.For activation,a homogeneous blend of VT and sodium hydroxide was calcinated at an elevated temperature and then modified with metakaolin to produce a geopolymeric precursor.During the thermal activation,the VT was corroded by sodium hydroxide and then sodium silicate formed on the particle surfaces.After water was added,the sodium silicate coating dissolved to release silicon species,which created an alkaline solution environment.The metakaolin then dissolved in the alkaline environment to generate aluminum species,which was followed by geopolymerization.The VT particles were connected by a gel produced during geopolymerization,which yielded a geopolymer with excellent mechanical performance.This investigation not only improves the feasibility of using geopolymer technology for large-scale and in-situ applications,but also promotes the utilization of VT and other silica-rich solid wastes.展开更多
Efficient thickening of tailings is a prerequisite for the metal mine tailings backfill and surface disposal operation.The effective collision of ultrafine tailings particles in suspension with flocculant molecules is...Efficient thickening of tailings is a prerequisite for the metal mine tailings backfill and surface disposal operation.The effective collision of ultrafine tailings particles in suspension with flocculant molecules is essential for flocs aggregates formation and settling.Unreasonable feeding speed and flocculant adding method will lead to the failure of effective dispersion of flocculant and high particle content in thickener overflow.In this work,the effect of turbulence intensity and flocculant adding method on floc size,strength,and movement characteristics are analysed.Aiming to solve the turbidity increased,a pilot-scale continuous thickening test was carried out.Taking a single particle and multiple flocs of full tailings as the research object,the particle iterative settlement model of flocs was established.The influence of turbulence intensity on collision effect is studied by tracking and simulating particle trajectory.The results show that in the process of single particle settlement,chaos appears in the iterative process owing to particle adhesion which caused by micro action.When the turbulence intensity is 25.99%,the maximum particle size of tailings floc is 6.21 mm and the maximum sedimentation rate is 5.284 cm·s^(−1).The tailings floc presents a multi-scale structure of particle-force chain system when hindered settling,and the interweaving of strong and weak force chains constitutes the topological structure of particles.The results are applied to a thicker in plant,the flocculant addition mode and feed rate are optimized,and the flocs settling speed and overflow clarity are improved.展开更多
BACKGROUND Total pancreatectomy (TP) is usually considered a therapeutic option forpancreatic cancer in which Whipple surgery and distal pancreatectomy areundesirable, but brittle diabetes and poor quality of life (Qo...BACKGROUND Total pancreatectomy (TP) is usually considered a therapeutic option forpancreatic cancer in which Whipple surgery and distal pancreatectomy areundesirable, but brittle diabetes and poor quality of life (QoL) remain majorconcerns. A subset of patients who underwent TP even died due to severehypoglycemia. For pancreatic cancer involving the pancreatic head and proximalbody but without invasion to the pancreatic tail, we performed partial pancreatictail preserving subtotal pancreatectomy (PPTP-SP) in selected patients, in order toimprove postoperative glycemic control and QoL without compromisingoncological outcomes.AIM To evaluate the efficacy of PPTP-SP for patients with pancreatic cancer.METHODS We retrospectively reviewed 56 patients with pancreatic ductal adenocarcinomawho underwent PPTP-SP (n = 18) or TP (n = 38) at our institution from May 2014to January 2019. Clinical outcomes were compared between the two groups, withan emphasis on oncological outcomes, postoperative glycemic control, and QoL.QoL was evaluated using the European Organization for Research and Treatmentof Cancer Quality of Life Questionnaire (EORTC QLQ-C30 and EORTC PAN26).All patients were followed until May 2019 or until death.RESULTS A total of 56 consecutive patients were enrolled in this study. Perioperativeoutcomes, recurrence-free survival, and overall survival were comparablebetween the two groups. No patients in the PPTP-SP group developed cancerrecurrence in the pancreatic tail stump or splenic hilum, or a clinical pancreaticfistula. Patients who underwent PPTP-SP had significantly better glycemiccontrol, based on their higher rate of insulin-independence (P = 0.014), lowerhemoglobin A1c (HbA1c) level (P = 0.046), lower daily insulin dosage (P < 0.001),and less frequent hypoglycemic episodes (P < 0.001). Global health was similar inthe two groups, but patients who underwent PPTP-SP had better functional status(P = 0.036), milder symptoms (P = 0.013), less severe diet restriction (P = 0.011),and higher confidence regarding future life (P = 0.035).CONCLUSION For pancreatic cancer involving the pancreatic head and proximal body, PPTP-SPachieves perioperative and oncological outcomes comparable to TP in selectedpatients while significantly improving long-term glycemic control and QoL.展开更多
For mines with poor ore bodies and surrounding rocks,the general mining method does not allow the ore to be extracted from underground safely and efficiently.For these mines,the downward layered filling mining techniq...For mines with poor ore bodies and surrounding rocks,the general mining method does not allow the ore to be extracted from underground safely and efficiently.For these mines,the downward layered filling mining technique is undoubtedly the most suitable mining method.The downward filling mining technique may eliminate the troubles relating to poor ore deposit conditions,such as production safety,ore loss rate,and depletion rate.However,in this technique,the safety of the artificial roof of the next stratum is of paramount importance.Cementitious tailings backfilling(CTB)that is not sufficiently cemented and causes collapses could threaten ore production.This paper explores a diamond-shaped composite structure to mimic the stability of a glued false roof in an actual infill mine based on the recently emerged three-dimensional(3D)printing technology.Experimental means such as three-point bending and digital image correlation(DIC)techniques were used to explore the flexural characteristics of 3D construction specimens and CTB combinations with different cement/tailings weight ratios at diverse layer heights.The results show that the 3D structure with a 14-mm ply height and CTB has strong flexural characteristics,with a maximum deflection value of 30.1 mm,while the 3D-printed rhomboid polymer(3D-PRP)structure with a 26-mm ply height is slightly worse in terms of flexural strength characteristics,but it has a higher maximum flexural strength of 2.83 MPa.A combination of 3D structure and CTB has more unique mechanical properties than CTB itself.This research work offers practical knowledge on the artificial roof performance of the downward layered filling mining technique and builds a scientific knowledge base regarding the successful application of CTB material in mines.展开更多
Estimation of stressses within the tailings slurry during self-weight consolidation is a critical issue for cost-effective barricade design and efficient backfill planning in underground mine stopes.This process requi...Estimation of stressses within the tailings slurry during self-weight consolidation is a critical issue for cost-effective barricade design and efficient backfill planning in underground mine stopes.This process requires a good understanding of self-weight consolidation behaviors of the tailings slurry within practical stopes,where many factors can have significant effects on the consolidation,including drainage condition and cement addition.In this paper,the prepared tailings slurry with different cement contents(0,4.76wt%,and 6.25wt%)was poured into1.2 m-high columns,which allowed three drainage scenarios(undrained,partial lateral drainage near the bottom part,and full lateral drainage boundaries)to investigate the effects of drainage condition and cement addition on the consolidation behavior of the tailings slurry.The consolidation behavior was analyzed in terms of pore water pressure(PWP),settlement,volume of drainage water,and residual water content.The results indicate that increasing the length of the drainage boundary or cement content aids in PWP dissipation.In addition,constructing an efficient drainage boundary was more favorable to PWP dissipation than increasing cement addition.The final stable PWP on the column floor was not sensitive to cement addition.The final settlement of uncemented tailings slurry was independent of drainage conditions,and that of cemented tailings slurry decreased with the increase in cement addition.Notably,more pore water can drain out from the cemented tailings slurry than the uncemented tailings slurry during consolidation.展开更多
The disposal of mining tailings has increasingly focused on the use of dry stacks.These structures offer more security since they use filtered and compacted material.Because of the construction method and the heights ...The disposal of mining tailings has increasingly focused on the use of dry stacks.These structures offer more security since they use filtered and compacted material.Because of the construction method and the heights achieved,the material that compounds the structure can be subjected to different stress paths along the failure plane.The theoretical framework considered in the design of these structures generally is the critical state soil mechanics(CSSM).However,the data in the literature concerning the uniqueness of critical state line(CSL)is still controversial as the soil is subjected to different stress paths.With respect to tailings,this question is even more restricted.This paper studies two tailings with different gradings due to the beneficial processes over extension and compression paths.A series of drained and undrained triaxial tests was conducted over a range of initial densities and stress levels.In the q-p'plane,different critical stress ratio(M)values were obtained for compression and extension stress paths.However,the critical state friction angle is very similar with a slightly higher critical state friction angle for extension tests.Curved stress path dependent CSLs were obtained in the n-lnp0 plane with the extension tests below the CSL defined in compression.Regarding the fines content,the studied tailings presented very similar M and critical state friction angle values.However,the fines content af-fects the volumetric behavior of the studied tailings and the CSLs on the n-lnp0 plane shift downwards with the increasing fines content for compression and extension tests.In relation to dilatancy analysis,the fines content did not present an evident influence on the dilatancy of the materials.However,different values of mean stress ratio N were obtained between compression and extension tests and can corroborate the existence of non-unique CSLs for these materials.展开更多
The flake-like basic magnesium carbonate was prepared from the ammonium sulfate leaching liquid of asbestos tailings. The method of X-ray diffraction, Fourier transform infrared spectra, TA-DTG and SEM analysis had be...The flake-like basic magnesium carbonate was prepared from the ammonium sulfate leaching liquid of asbestos tailings. The method of X-ray diffraction, Fourier transform infrared spectra, TA-DTG and SEM analysis had been used to research the influence of the reaction temperature on the phase, structure and morphology of the product during the preparation of the basic magnesium carbonate. The results indicates that the product was needle-like magnesium carbonate hydrate at the lower reaction temperature (from 35 ℃ to 65℃), with the increase of the reaction temperature (75 ℃ to 95 ℃ ), the needle-like magnesium carbonate hydrate (MgCO3·xH2O) transformed to flake-like basic magnesium carbonate [Mg5(CO3)4(OH)2·4H2O], the reaction temperature plays an important role in the preparation of flake-like basic magnesium carbonate, the preparation of flake-like basic magnesium carbonate was a nucleation-dissolution-recrystallization growth mechanism process.展开更多
To determine the pollution levels and potential toxic risks of arsenic(As) and heavy metals(Cr, Ni, Cu, Zn, Pb and Cd) in water and suspended particulate matter(SPM) in tail reaches(including freshwater reach and low-...To determine the pollution levels and potential toxic risks of arsenic(As) and heavy metals(Cr, Ni, Cu, Zn, Pb and Cd) in water and suspended particulate matter(SPM) in tail reaches(including freshwater reach and low-salinity reach) of the Yellow River as the Flow-Sediment Regulation Project(FSRP) has been carried out for approximately 15 yr, the surface water and SPM were sampled at pre-flood(April) and post-flood seasons(October). Results showed that similar changes of As and metal levels in water and SPM were observed along the tail reaches at pre-flood or post-flood season. Compared to pre-flood season, the levels of As, Cu, Cr and Ni in freshwater reach and the concentrations of Cr and Ni in low-salinity reach rose greatly at post-flood season. The levels of As and metals in SPM of freshwater reach or low-salinity reach at pre-flood season were significantly higher than those at post-flood season(P < 0.01).The pollutions of As and metals in surface water of tail reaches at pre-flood or post-flood season were not serious. The SPM in freshwater reach at pre-flood season were polluted by Cd, As, Cr, Cu and Ni while those in low-salinity reach were polluted by Cd and Cr. The SPM in freshwater reach at post-flood season were polluted by Cd and Pb while those in low-salinity reach were polluted by Cd and Cr.Cd was identified as heavy metal of primary concern at both pre-flood and post-flood seasons. Combined with the existed data reported in present research, this study found that the toxic risk of As and metals in SPM of tail reaches at pre-flood season was higher than that at post-flood season, implying that the implementation of FSRP during flooding season, to a great extent, reduced the toxic risk of these elements. With the long-term implementation of FSRP, the pollution levels of As and metals(particularly for Cd) in SPM of tail reaches might be elevated and the potential toxic risk primarily produced by Cr, Ni and As might be increased if effective measures were not taken in future.展开更多
The 3D reconstruction and quantitative characterization of drainage channels and coarse tailings particles in a bed were conducted in this study.The influence of variations in the azimuthal angle(θ)and polar angle(φ...The 3D reconstruction and quantitative characterization of drainage channels and coarse tailings particles in a bed were conducted in this study.The influence of variations in the azimuthal angle(θ)and polar angle(φ)of coarse particles on drainage channel structure was analyzed,and the drainage mechanism of the bed was studied.Results showed that water discharge in the bed reduced the size of pores and throat channels,increasing slurry concentration.The throat channel structure was a key component of the drainage process.Theφandθof particles changed predominantly along the length direction.The changes inφhad a cumulative plugging effect on the drainage channel and increased the difficulty of water discharge.The rake and rod formed a shear ring in the tailings bed with shear,and theθdistribution of particles changed from disorderly to orderly during the rotation process.The drainage channel was squeezed during the shearing process with the change inθ,which broke the channel structure,encouraged water discharge in the bed,and facilitated a further increase in slurry concentration.The findings of this work are expected to offer theoretical guidance for preparing high-concentration underflow in the tailings thickening process.展开更多
Limited by mining technology,mineral exploitation can produce large amounts of tailings.Heavy summer rainfall or seasonal freeze-thaw can lead to physical and chemical modification of tailing material in mountainous a...Limited by mining technology,mineral exploitation can produce large amounts of tailings.Heavy summer rainfall or seasonal freeze-thaw can lead to physical and chemical modification of tailing material in mountainous areas,resulting in fluidized tailings flow and severe disaster losses.Therefore,aiming at the problem of tailings fluidization catastrophe,this paper tried to reveal the rheological mechanism of tailings fluidization transformation by combining rheological tests and theoretical analysis.The results show that the yield stress increases with decreasing temperature,and when the density of debris flow(ρ)is more than 1.9 g/cm~3,this behavior becomes more pronounced as the density increases.The storage modulus decreases by at least two orders of magnitude at the solid-fluid transition under amplitude test sweep.Storage and loss modulus in the linear viscoelastic range and yield stress have an exponential growth relationship with sediment concentration.In addition,a stress constitutive relation and a new exponential law describing the evolution of yield stress required for solid-liquid transformation were proposed,and the relationship is further strengthened through a comprehensive analysis of existing results,which expands the evaluation application of the rheological characteristics of tailings flow.This paper provides a new insight into the rheological properties of tailing and how they occur through solid-liquid transition under different environments,which is beneficial to geological hazard prevention and the ecological remediation of the mining area.展开更多
Photocatalytic processes are efficient methods to solve water contamination problems,especially considering dyeing wastewater disposal.However,high-efficiency photocatalysts are usually very expensive and have the ris...Photocatalytic processes are efficient methods to solve water contamination problems,especially considering dyeing wastewater disposal.However,high-efficiency photocatalysts are usually very expensive and have the risk of heavy metal pollution.Recently,an iron oxides@hydrothermal carbonation carbon(HTCC)heterogeneous catalyst was prepared by our group through co-hydrothermal treatment of carbohydrates and zinc extraction tailings of converter dust.Herein,the catalytic performance of the iron oxides@HTCC was verified by a nonbiodegradable dye,methylene blue(MB),and the catalytic mechanism was deduced from theoretical simulations and spectroscopic measurements.The iron oxides@HTCC showed an excellent synergy between photocatalysis and Fenton-like reactions.Under visible-light illumination,the iron oxides@HTCC could be excited to generate electrons and holes,reacting with H_(2)O_(2)to produce·OH radicals to oxidize and decompose organic pollutants.The removal efficiency of methylene blue over iron oxides@HTCC at 140 min was 2.86 times that of HTCC.The enhanced catalytic performance was attributed to the advantages of iron oxides modification:(1)promoting the excitation induced by photons;(2)improving the charge transfer.Furthermore,the iron oxides@HTCC showed high catalytic activity in a wide pH value range of 2.3-10.4,and the MB removal efficiency remained higher than 95% after the iron oxides@HTCC was recycled 4 times.The magnetically recyclable iron oxides@HTCC may provide a solution for the treatment of wastewater from the textile industry.展开更多
To develop the microwave absorbing(MA)properties of cementitious material mixed with mine solid waste,the iron tailings cementitious microwave absorbing materials were prepared.The iron tailings was treated into diffe...To develop the microwave absorbing(MA)properties of cementitious material mixed with mine solid waste,the iron tailings cementitious microwave absorbing materials were prepared.The iron tailings was treated into different particle sizes by planetary ball mill,and the physicochemical properties of iron tailings were tested by laser particle size analyzer and scanning electron microscope(SEM).The electromagnetic parameters of iron tailings cementitious materials were characterized by a vector network analyzer and simulated MA properties,and the MA properties of iron tailings-cement composite system with steel fiber as absorber was studied.Based on the design of the single-layer structure,optimum mix ratio and thickness configuration method of double-layer structure were further studied,meanwhile,the mechanical properties and engineering application were analyzed and discussed.The results show that the particle size of iron tailings can afiect its electromagnetic behavior in cementitious materials,and the smaller particles lead the increase of demagnetisation efiect induced by domain wall motion and achieve better microwave absorbing properties in cementitious materials.When the thickness of matching layer and absorbing layer is 5 mm,the optimized microwave absorbing properties of C1/C3 double-layer cementitious material can obtain optimal RL value of-27.61 dB and efiective absorbing bandwidth of 0.97 GHz,which attributes to the synergistic efiect of impedance matching and attenuation characteristics.The double-layer microwave absorbing materials obtain excellent absorbing properties and show great design flexibility and diversity,which can be used as a suitable candidate for the preparation of favorable microwave absorbing cementitious materials.展开更多
The use of some environmental functional minerals as backfill-modified materials may improve the leaching resistance of cemented uranium tailings backfill created from alkali-activated slag(CUTB),but these materials m...The use of some environmental functional minerals as backfill-modified materials may improve the leaching resistance of cemented uranium tailings backfill created from alkali-activated slag(CUTB),but these materials may participate in the hydration reaction of the cementitious materials,which could have a certain impact on the pore structure of the CUTB,thus affecting its mechanical properties and leaching resistance.In this paper,natural zeolite is selected as the backfill-modified material,and it is added to alkali-activated slag paste(AASP)and CUTB in cementitious material proportions of 4%,8%,12%,and 16%to prepare AASP mixtures and CUTB mixtures containing environmental functional minerals.After the addition of natural zeolite,the porosity of the CUTB generally increases,but when the content is 4%,the porosity decreases to 22.30%.The uniaxial compressive strength(UCS)of the CUTB generally decreases,but the decrease is the smallest when the content is 4%,and the UCS is 12.37 MPa.The addition of natural zeolite mainly reduces the number of fine pores in the CUTB,but the pores with relaxation times T_(2)of greater than 10 ms account for about 10%of the total pores,and there are a certain number of large pores in the CUTB.The main product of alkali-activated slag is calcium(alumino)silicate hydrate(C-(A)-S-H gel).When natural zeolite is added,the hydration products develop towards denser products with a high degree of polymerization and the formation of low polymerization products is reduced.This affects the internal fracture pores of the hydration products and the interface pores of the CUTB,has an irregular effect on the pore characteristics of the CUTB,and influences the UCS.展开更多
Channel avulsion is a natural phenomenon that occurs abruptly on alluvial river deltas,which can affect the channel stability.The causes for avulsion could be generally categorized as topography-and flood-driven facto...Channel avulsion is a natural phenomenon that occurs abruptly on alluvial river deltas,which can affect the channel stability.The causes for avulsion could be generally categorized as topography-and flood-driven factors.However,previous studies on avulsion thresholds usually focused on topography-driven factors due to the centurial or millennial avulsion timescales of the world’s most deltas,but neglected the impacts of flood-driven factors.In the current study,a novel demarcation equation including the two driven factors was proposed,with the decadal timescale of avulsion being considered in the Yellow River Estuary(YRE).In order to quantify the contributions of different factors in each category,an entropy-based methodology was used to calculate the contributing weights of these factors.The factor with the highest weight in each category was then used to construct the demarcation equation,based on avulsion datasets associated with the YRE.An avulsion threshold was deduced according to the demarcation equation.This avulsion threshold was then applied to conduct the risk assessment of avulsion in the YRE.The results show that:two dominant factors cover respectively geomorphic coefficient representing the topography-driven factor and fluvial erosion intensity representing the flood-driven factor,which were thus employed to define a two dimensional mathematical space in which the demarcation equation can be obtained;the avulsion threshold derived from the equation was also applied in the risk assessment of avulsion;and the avulsion threshold proposed in this study is more accurate,as compared with the existing thresholds.展开更多
基金financially supported by the National Natural Science Foundation of China (Nos.52104156,52074351 and 52004330)the Science and Technology Innovation Program of Hunan Province,China (No.2021RC3125).
文摘Pipeline hydraulic transport is a highly efficient and low energy-consumption method for transporting solids and is commonly used for tailing slurry transport in the mining industry.Erosion wear(EW)remains the main cause of failure in tailings slurry pipeline systems,particularly at bends.EW is a complex phenomenon influenced by numerous factors,but research in this area has been limited.This study performs numerical simulations of slurry transport at the bend by combining computational fluid dynamics and fluid particle tracking using a wear model.Based on the validation of the feasibility of the model,this work focuses on the effects of coupled inlet velocity(IV)ranging from 1.5 to 3.0 m·s^(-1),particle size(PS)ranging from 50 to 650μm,and bend angle(BA)ranging from 45°to 90°on EW at the bend in terms of particle kinetic energy and incidence angle.The results show that the maximum EW rate of the slurry at the bend increases exponentially with IV and PS and first increases and then decreases with the increase in BA with the inflection point at 60°within these parameter ranges.Further comprehensive analysis reveals that the sensitivity level of the three factors to the maximum EW rate is PS>IV>BA,and when IV is 3.0 m/s,PS is 650μm,and BA is 60°,the bend EW is the most severe,and the maximum EW rate is 5.68×10^(-6)kg·m^(-2)·s^(-1).In addition,When PS is below or equal to 450μm,the maximum EW position is mainly at the outlet of the bend.When PS is greater than 450μm,the maximum EW position shifts toward the center of the bend with the increase in BA.Therefore,EW at the bend can be reduced in practice by reducing IV as much as possible and using small particles.
文摘The disposal of filtered tailings in high dry stacks can induce particle breakage,changing the material's behaviour during the structure's lifetime.The grading changes influence material properties at the critical state,and this is not mature for intermediate artificial soils(tailings)in a broad range of confining pressures.In this paper,it aims to describe the behaviour of iron ore tailings in a spectrum of confining pressures broader than the reported in previous studies.A series of consolidated drained(CD)triaxial tests was carried out with confining pressures ranging from 0.075 MPa to 120 MPa.These results show that the amount of breakage plays an essential role in the response of iron ore tailings.The existence of curved critical state line(CSL)in both specific volume(ν)-logarithm of mean effective stress(p′)and deviatoric stress(q)-mean effective stress(p′)planes,and different responses in the deviatoric stress-axial strain-volumetric strain curves were verified.An inverse S-shaped equation was proposed to represent the silty-sandy tailings'behaviour up to high pressures onν-lnp′plane.The proposed equation provides a basis for enhancing constitutive models and considers the evolution of the grading up to severe loading conditions.The adjustment considered three regions with different responses associated with particle breakage at different pressure levels.
基金supported by the Shandong Provin-cial Key Research Project of Undergraduate Teaching Reform(No.Z2022218)the Fundamental Research Funds for the Central University(No.202113028)+1 种基金the Graduate Education Promotion Program of Ocean University of China(No.HDJG20006)supported by the Sailing Laboratory of Ocean University of China.
文摘The tell tail is usually placed on the triangular sail to display the running state of the air flow on the sail surface.It is of great significance to make accurate judgement on the drift of the tell tail of the sailboat during sailing for the best sailing effect.Normally it is difficult for sailors to keep an eye for a long time on the tell sail for accurate judging its changes,affected by strong sunlight and visual fatigue.In this case,we adopt computer vision technology in hope of helping the sailors judge the changes of the tell tail in ease with ease.This paper proposes for the first time a method to classify sailboat tell tails based on deep learning and an expert guidance system,supported by a sailboat tell tail classification data set on the expert guidance system of interpreting the tell tails states in different sea wind conditions,including the feature extraction performance.Considering the expression capabilities that vary with the computational features in different visual tasks,the paper focuses on five tell tail computing features,which are recoded by an automatic encoder and classified by a SVM classifier.All experimental samples were randomly divided into five groups,and four groups were selected from each group as the training set to train the classifier.The remaining one group was used as the test set for testing.The highest resolution value of the ResNet network was 80.26%.To achieve better operational results on the basis of deep computing features obtained through the ResNet network in the experiments.The method can be used to assist the sailors in making better judgement about the tell tail changes during sailing.
基金financially supported by the National Key Research and Development Program of China(No.2022YFC2905004)the China Postdoctoral Science Foundation(No.2023M742134)。
文摘Polypropylene(PP)fiber-reinforced cement-based tailings backfill(FRCTB)is a green compound material with superior crack resistance and has good prospects for application in underground mining.However,FRCTB exhibits susceptibility to dynamic events,such as impact ground pressure and blast vibrations.This paper investigates the energy and crack distribution behavior of FRCTB under dynamic impact,considering the height/diameter(H/D)effect.Split Hopkinson pressure bar,industrial computed tomography scan,and scanning electron microscopy(SEM)experiments were carried out on six types of FRCTB.Laboratory outcomes confirmed fiber aggregation at the bottom of specimens.When H/D was less than 0.8,the proportion of PP fibers distributed along theθangle direction of80°-90°increased.For the total energy,all samples presented similar energy absorption,reflectance,and transmittance.However,a rise in H/D may cause a rise in the energy absorption rate of FRCTB during the peak phase.A positive correlation existed between the average strain rate and absorbed energy per unit volume.The increase in H/D resulted in a decreased crack volume fraction of FRCTB.When the H/D was greater than or equal to 0.7,the maximum crack volume fraction of FRCTB was observed close to the incidence plane.Radial cracks were present only in the FRCTB with an H/D ratio of 0.5.Samples with H/D ratios of 0.5 and 0.6 showed similar distributions of weakly and heavily damaged areas.PP fibers can limit the emergence and expansion of cracks by influencing their path.SEM observations revealed considerable differences in the bonding strengths between fibers and the FRCTB.Fibers that adhered particularly well to the substrate were attracted together with the hydration products adhering to surfaces.These results show that FRCTB is promising as a sustainable and green backfill for determining the design properties of mining with backfill.
基金financially supported by the National Natural Science Foundation of China(Nos.52130404 and 52304121)the Fundamental Research Funds for the Central Universities(No.FRF-TP-22-112A1)+4 种基金the Guangdong Basic and Applied Basic Research Foundation(No.2021A 1515110161)the ANID(Chile)through Fondecyt project 1210610the Centro de Modelamiento Matemático(BASAL funds for Centers of Excellence FB210005)the CRHIAM project ANID/FONDAP/15130015 and ANID/FONDAP/1523A0001the Anillo project ANID/ACT210030。
文摘Cemented paste backfill(CPB)is a key technology for green mining in metal mines,in which tailings thickening comprises the primary link of CPB technology.However,difficult flocculation and substandard concentrations of thickened tailings often occur.The rheological properties and concentration evolution in the thickened tailings remain unclear.Moreover,traditional indoor thickening experiments have yet to quantitatively characterize their rheological properties.An experiment of flocculation condition optimization based on the Box-Behnken design(BBD)was performed in the study,and the two response values were investigated:concentration and the mean weighted chord length(MWCL)of flocs.Thus,optimal flocculation conditions were obtained.In addition,the rheological properties and concentration evolution of different flocculant dosages and ultrafine tailing contents under shear,compression,and compression-shear coupling experimental conditions were tested and compared.The results show that the shear yield stress under compression and compression-shear coupling increases with the growth of compressive yield stress,while the shear yield stress increases slightly under shear.The order of shear yield stress from low to high under different thickening conditions is shear,compression,and compression-shear coupling.Under compression and compression-shear coupling,the concentration first rapidly increases with the growth of compressive yield stress and then slowly increases,while concentration increases slightly under shear.The order of concentration from low to high under different thickening conditions is shear,compression,and compression-shear coupling.Finally,the evolution mechanism of the flocs and drainage channels during the thickening of the thickened tailings under different experimental conditions was revealed.
文摘This paper discusses a queueing system with a retrial orbit and batch service, in which the quantity of customers’ rooms in the queue is finite and the space of retrial orbit is infinite. When the server starts serving, it serves all customers in the queue in a single batch, which is the so-called batch service. If a new customer or a retrial customer finds all the customers’ rooms are occupied, he will decide whether or not to join the retrial orbit. By using the censoring technique and the matrix analysis method, we first obtain the decay function of the stationary distribution for the quantity of customers in the retrial orbit and the quantity of customers in the queue. Then based on the form of decay rate function and the Karamata Tauberian theorem, we finally get the exact tail asymptotics of the stationary distribution.
基金This work was financially supported by the Major Tech-nical Innovation Project of Hubei Province,China(No.2018ACA157)the National Natural Science Foundation of China(No.51874222)the Excellent Dissertation Cul-tivation Funds of Wuhan University of Technology(No.2018-YS-052).
文摘The aim of this investigation was to prepare geopolymeric precursor from vanadium tailing(VT)by thermal activation and modification.For activation,a homogeneous blend of VT and sodium hydroxide was calcinated at an elevated temperature and then modified with metakaolin to produce a geopolymeric precursor.During the thermal activation,the VT was corroded by sodium hydroxide and then sodium silicate formed on the particle surfaces.After water was added,the sodium silicate coating dissolved to release silicon species,which created an alkaline solution environment.The metakaolin then dissolved in the alkaline environment to generate aluminum species,which was followed by geopolymerization.The VT particles were connected by a gel produced during geopolymerization,which yielded a geopolymer with excellent mechanical performance.This investigation not only improves the feasibility of using geopolymer technology for large-scale and in-situ applications,but also promotes the utilization of VT and other silica-rich solid wastes.
基金funded by the National Natural Science Foundation of China (No. 51834001)
文摘Efficient thickening of tailings is a prerequisite for the metal mine tailings backfill and surface disposal operation.The effective collision of ultrafine tailings particles in suspension with flocculant molecules is essential for flocs aggregates formation and settling.Unreasonable feeding speed and flocculant adding method will lead to the failure of effective dispersion of flocculant and high particle content in thickener overflow.In this work,the effect of turbulence intensity and flocculant adding method on floc size,strength,and movement characteristics are analysed.Aiming to solve the turbidity increased,a pilot-scale continuous thickening test was carried out.Taking a single particle and multiple flocs of full tailings as the research object,the particle iterative settlement model of flocs was established.The influence of turbulence intensity on collision effect is studied by tracking and simulating particle trajectory.The results show that in the process of single particle settlement,chaos appears in the iterative process owing to particle adhesion which caused by micro action.When the turbulence intensity is 25.99%,the maximum particle size of tailings floc is 6.21 mm and the maximum sedimentation rate is 5.284 cm·s^(−1).The tailings floc presents a multi-scale structure of particle-force chain system when hindered settling,and the interweaving of strong and weak force chains constitutes the topological structure of particles.The results are applied to a thicker in plant,the flocculant addition mode and feed rate are optimized,and the flocs settling speed and overflow clarity are improved.
基金We thank Professor Yang F and Dr. Shi HJ for their contribution to manuscriptrevision, Yan D and Lee E for further linguistic revision, and Zhang L for diagramdrawing.
文摘BACKGROUND Total pancreatectomy (TP) is usually considered a therapeutic option forpancreatic cancer in which Whipple surgery and distal pancreatectomy areundesirable, but brittle diabetes and poor quality of life (QoL) remain majorconcerns. A subset of patients who underwent TP even died due to severehypoglycemia. For pancreatic cancer involving the pancreatic head and proximalbody but without invasion to the pancreatic tail, we performed partial pancreatictail preserving subtotal pancreatectomy (PPTP-SP) in selected patients, in order toimprove postoperative glycemic control and QoL without compromisingoncological outcomes.AIM To evaluate the efficacy of PPTP-SP for patients with pancreatic cancer.METHODS We retrospectively reviewed 56 patients with pancreatic ductal adenocarcinomawho underwent PPTP-SP (n = 18) or TP (n = 38) at our institution from May 2014to January 2019. Clinical outcomes were compared between the two groups, withan emphasis on oncological outcomes, postoperative glycemic control, and QoL.QoL was evaluated using the European Organization for Research and Treatmentof Cancer Quality of Life Questionnaire (EORTC QLQ-C30 and EORTC PAN26).All patients were followed until May 2019 or until death.RESULTS A total of 56 consecutive patients were enrolled in this study. Perioperativeoutcomes, recurrence-free survival, and overall survival were comparablebetween the two groups. No patients in the PPTP-SP group developed cancerrecurrence in the pancreatic tail stump or splenic hilum, or a clinical pancreaticfistula. Patients who underwent PPTP-SP had significantly better glycemiccontrol, based on their higher rate of insulin-independence (P = 0.014), lowerhemoglobin A1c (HbA1c) level (P = 0.046), lower daily insulin dosage (P < 0.001),and less frequent hypoglycemic episodes (P < 0.001). Global health was similar inthe two groups, but patients who underwent PPTP-SP had better functional status(P = 0.036), milder symptoms (P = 0.013), less severe diet restriction (P = 0.011),and higher confidence regarding future life (P = 0.035).CONCLUSION For pancreatic cancer involving the pancreatic head and proximal body, PPTP-SPachieves perioperative and oncological outcomes comparable to TP in selectedpatients while significantly improving long-term glycemic control and QoL.
基金financially supported by the National Key Research and Development Program of China(No.2022YFC2905004)the National Natural Science Foundation of China(No.51804017)。
文摘For mines with poor ore bodies and surrounding rocks,the general mining method does not allow the ore to be extracted from underground safely and efficiently.For these mines,the downward layered filling mining technique is undoubtedly the most suitable mining method.The downward filling mining technique may eliminate the troubles relating to poor ore deposit conditions,such as production safety,ore loss rate,and depletion rate.However,in this technique,the safety of the artificial roof of the next stratum is of paramount importance.Cementitious tailings backfilling(CTB)that is not sufficiently cemented and causes collapses could threaten ore production.This paper explores a diamond-shaped composite structure to mimic the stability of a glued false roof in an actual infill mine based on the recently emerged three-dimensional(3D)printing technology.Experimental means such as three-point bending and digital image correlation(DIC)techniques were used to explore the flexural characteristics of 3D construction specimens and CTB combinations with different cement/tailings weight ratios at diverse layer heights.The results show that the 3D structure with a 14-mm ply height and CTB has strong flexural characteristics,with a maximum deflection value of 30.1 mm,while the 3D-printed rhomboid polymer(3D-PRP)structure with a 26-mm ply height is slightly worse in terms of flexural strength characteristics,but it has a higher maximum flexural strength of 2.83 MPa.A combination of 3D structure and CTB has more unique mechanical properties than CTB itself.This research work offers practical knowledge on the artificial roof performance of the downward layered filling mining technique and builds a scientific knowledge base regarding the successful application of CTB material in mines.
基金financially supported by the Young Scientist Project of the National Key Research and Development Program of China (No.2021YFC2900600)the Beijing Nova Program (No.20220484057)financial support from China Scholarship Council under Grant CSC No.202110300001。
文摘Estimation of stressses within the tailings slurry during self-weight consolidation is a critical issue for cost-effective barricade design and efficient backfill planning in underground mine stopes.This process requires a good understanding of self-weight consolidation behaviors of the tailings slurry within practical stopes,where many factors can have significant effects on the consolidation,including drainage condition and cement addition.In this paper,the prepared tailings slurry with different cement contents(0,4.76wt%,and 6.25wt%)was poured into1.2 m-high columns,which allowed three drainage scenarios(undrained,partial lateral drainage near the bottom part,and full lateral drainage boundaries)to investigate the effects of drainage condition and cement addition on the consolidation behavior of the tailings slurry.The consolidation behavior was analyzed in terms of pore water pressure(PWP),settlement,volume of drainage water,and residual water content.The results indicate that increasing the length of the drainage boundary or cement content aids in PWP dissipation.In addition,constructing an efficient drainage boundary was more favorable to PWP dissipation than increasing cement addition.The final stable PWP on the column floor was not sensitive to cement addition.The final settlement of uncemented tailings slurry was independent of drainage conditions,and that of cemented tailings slurry decreased with the increase in cement addition.Notably,more pore water can drain out from the cemented tailings slurry than the uncemented tailings slurry during consolidation.
基金wish to express their appreciation to Vale S.A.and Brazilian Research Council(CNPq)for the support to the research group.
文摘The disposal of mining tailings has increasingly focused on the use of dry stacks.These structures offer more security since they use filtered and compacted material.Because of the construction method and the heights achieved,the material that compounds the structure can be subjected to different stress paths along the failure plane.The theoretical framework considered in the design of these structures generally is the critical state soil mechanics(CSSM).However,the data in the literature concerning the uniqueness of critical state line(CSL)is still controversial as the soil is subjected to different stress paths.With respect to tailings,this question is even more restricted.This paper studies two tailings with different gradings due to the beneficial processes over extension and compression paths.A series of drained and undrained triaxial tests was conducted over a range of initial densities and stress levels.In the q-p'plane,different critical stress ratio(M)values were obtained for compression and extension stress paths.However,the critical state friction angle is very similar with a slightly higher critical state friction angle for extension tests.Curved stress path dependent CSLs were obtained in the n-lnp0 plane with the extension tests below the CSL defined in compression.Regarding the fines content,the studied tailings presented very similar M and critical state friction angle values.However,the fines content af-fects the volumetric behavior of the studied tailings and the CSLs on the n-lnp0 plane shift downwards with the increasing fines content for compression and extension tests.In relation to dilatancy analysis,the fines content did not present an evident influence on the dilatancy of the materials.However,different values of mean stress ratio N were obtained between compression and extension tests and can corroborate the existence of non-unique CSLs for these materials.
文摘The flake-like basic magnesium carbonate was prepared from the ammonium sulfate leaching liquid of asbestos tailings. The method of X-ray diffraction, Fourier transform infrared spectra, TA-DTG and SEM analysis had been used to research the influence of the reaction temperature on the phase, structure and morphology of the product during the preparation of the basic magnesium carbonate. The results indicates that the product was needle-like magnesium carbonate hydrate at the lower reaction temperature (from 35 ℃ to 65℃), with the increase of the reaction temperature (75 ℃ to 95 ℃ ), the needle-like magnesium carbonate hydrate (MgCO3·xH2O) transformed to flake-like basic magnesium carbonate [Mg5(CO3)4(OH)2·4H2O], the reaction temperature plays an important role in the preparation of flake-like basic magnesium carbonate, the preparation of flake-like basic magnesium carbonate was a nucleation-dissolution-recrystallization growth mechanism process.
基金Under the auspices of National Natural Science Foundation of China(No.41971128,41371104)the Award Program for Min River Scholar in Fujian Province(No.Min 201531)。
文摘To determine the pollution levels and potential toxic risks of arsenic(As) and heavy metals(Cr, Ni, Cu, Zn, Pb and Cd) in water and suspended particulate matter(SPM) in tail reaches(including freshwater reach and low-salinity reach) of the Yellow River as the Flow-Sediment Regulation Project(FSRP) has been carried out for approximately 15 yr, the surface water and SPM were sampled at pre-flood(April) and post-flood seasons(October). Results showed that similar changes of As and metal levels in water and SPM were observed along the tail reaches at pre-flood or post-flood season. Compared to pre-flood season, the levels of As, Cu, Cr and Ni in freshwater reach and the concentrations of Cr and Ni in low-salinity reach rose greatly at post-flood season. The levels of As and metals in SPM of freshwater reach or low-salinity reach at pre-flood season were significantly higher than those at post-flood season(P < 0.01).The pollutions of As and metals in surface water of tail reaches at pre-flood or post-flood season were not serious. The SPM in freshwater reach at pre-flood season were polluted by Cd, As, Cr, Cu and Ni while those in low-salinity reach were polluted by Cd and Cr. The SPM in freshwater reach at post-flood season were polluted by Cd and Pb while those in low-salinity reach were polluted by Cd and Cr.Cd was identified as heavy metal of primary concern at both pre-flood and post-flood seasons. Combined with the existed data reported in present research, this study found that the toxic risk of As and metals in SPM of tail reaches at pre-flood season was higher than that at post-flood season, implying that the implementation of FSRP during flooding season, to a great extent, reduced the toxic risk of these elements. With the long-term implementation of FSRP, the pollution levels of As and metals(particularly for Cd) in SPM of tail reaches might be elevated and the potential toxic risk primarily produced by Cr, Ni and As might be increased if effective measures were not taken in future.
基金financially supported by the National Key R&D Program of China(No.2022YFC2903803)National Natural Science Foundation of China(No.52130404)+4 种基金Guangdong Basic and Applied Basic Research Foundation(No.2021A1515110161)ANID(Chile)through Fondecyt project 1210610Centro de Modelamiento Matemático(BASAL funds for Centers of Excellence FB210005)CRHIAM project ANID/FONDAP/15130015Anillo project ANID/ACT210030。
文摘The 3D reconstruction and quantitative characterization of drainage channels and coarse tailings particles in a bed were conducted in this study.The influence of variations in the azimuthal angle(θ)and polar angle(φ)of coarse particles on drainage channel structure was analyzed,and the drainage mechanism of the bed was studied.Results showed that water discharge in the bed reduced the size of pores and throat channels,increasing slurry concentration.The throat channel structure was a key component of the drainage process.Theφandθof particles changed predominantly along the length direction.The changes inφhad a cumulative plugging effect on the drainage channel and increased the difficulty of water discharge.The rake and rod formed a shear ring in the tailings bed with shear,and theθdistribution of particles changed from disorderly to orderly during the rotation process.The drainage channel was squeezed during the shearing process with the change inθ,which broke the channel structure,encouraged water discharge in the bed,and facilitated a further increase in slurry concentration.The findings of this work are expected to offer theoretical guidance for preparing high-concentration underflow in the tailings thickening process.
基金supported by The National Nat ural Science Foundation of China(No.42207184)Nature Science Basic Research Plan in Shaanxi Provi nce of China(No.2022JQ-253)。
文摘Limited by mining technology,mineral exploitation can produce large amounts of tailings.Heavy summer rainfall or seasonal freeze-thaw can lead to physical and chemical modification of tailing material in mountainous areas,resulting in fluidized tailings flow and severe disaster losses.Therefore,aiming at the problem of tailings fluidization catastrophe,this paper tried to reveal the rheological mechanism of tailings fluidization transformation by combining rheological tests and theoretical analysis.The results show that the yield stress increases with decreasing temperature,and when the density of debris flow(ρ)is more than 1.9 g/cm~3,this behavior becomes more pronounced as the density increases.The storage modulus decreases by at least two orders of magnitude at the solid-fluid transition under amplitude test sweep.Storage and loss modulus in the linear viscoelastic range and yield stress have an exponential growth relationship with sediment concentration.In addition,a stress constitutive relation and a new exponential law describing the evolution of yield stress required for solid-liquid transformation were proposed,and the relationship is further strengthened through a comprehensive analysis of existing results,which expands the evaluation application of the rheological characteristics of tailings flow.This paper provides a new insight into the rheological properties of tailing and how they occur through solid-liquid transition under different environments,which is beneficial to geological hazard prevention and the ecological remediation of the mining area.
基金financially supported by the National Natural Science Foundation of China(No.52074035)the Fundamental Research Funds for the Central Universities,China(No.00007720)the National Key Research and Development Program of China(No.2020YFC1910000)。
文摘Photocatalytic processes are efficient methods to solve water contamination problems,especially considering dyeing wastewater disposal.However,high-efficiency photocatalysts are usually very expensive and have the risk of heavy metal pollution.Recently,an iron oxides@hydrothermal carbonation carbon(HTCC)heterogeneous catalyst was prepared by our group through co-hydrothermal treatment of carbohydrates and zinc extraction tailings of converter dust.Herein,the catalytic performance of the iron oxides@HTCC was verified by a nonbiodegradable dye,methylene blue(MB),and the catalytic mechanism was deduced from theoretical simulations and spectroscopic measurements.The iron oxides@HTCC showed an excellent synergy between photocatalysis and Fenton-like reactions.Under visible-light illumination,the iron oxides@HTCC could be excited to generate electrons and holes,reacting with H_(2)O_(2)to produce·OH radicals to oxidize and decompose organic pollutants.The removal efficiency of methylene blue over iron oxides@HTCC at 140 min was 2.86 times that of HTCC.The enhanced catalytic performance was attributed to the advantages of iron oxides modification:(1)promoting the excitation induced by photons;(2)improving the charge transfer.Furthermore,the iron oxides@HTCC showed high catalytic activity in a wide pH value range of 2.3-10.4,and the MB removal efficiency remained higher than 95% after the iron oxides@HTCC was recycled 4 times.The magnetically recyclable iron oxides@HTCC may provide a solution for the treatment of wastewater from the textile industry.
基金Funded by the Natural Science Foundation of Nanping of China(No.N2021J002)Guangdong Basic and Applied Basic Research Foundation(No.2020A1515110304)+3 种基金Guangzhou Science and Technology Plan(No.202102020224)Natural Science Foundation of Fujian Province(No.2020Y0092)Natural Science Foundation of Fujian Province(No.2023J011044)Resource Chemical Industry and Technology Foundation of Nanping(No.N2020Z003)。
文摘To develop the microwave absorbing(MA)properties of cementitious material mixed with mine solid waste,the iron tailings cementitious microwave absorbing materials were prepared.The iron tailings was treated into different particle sizes by planetary ball mill,and the physicochemical properties of iron tailings were tested by laser particle size analyzer and scanning electron microscope(SEM).The electromagnetic parameters of iron tailings cementitious materials were characterized by a vector network analyzer and simulated MA properties,and the MA properties of iron tailings-cement composite system with steel fiber as absorber was studied.Based on the design of the single-layer structure,optimum mix ratio and thickness configuration method of double-layer structure were further studied,meanwhile,the mechanical properties and engineering application were analyzed and discussed.The results show that the particle size of iron tailings can afiect its electromagnetic behavior in cementitious materials,and the smaller particles lead the increase of demagnetisation efiect induced by domain wall motion and achieve better microwave absorbing properties in cementitious materials.When the thickness of matching layer and absorbing layer is 5 mm,the optimized microwave absorbing properties of C1/C3 double-layer cementitious material can obtain optimal RL value of-27.61 dB and efiective absorbing bandwidth of 0.97 GHz,which attributes to the synergistic efiect of impedance matching and attenuation characteristics.The double-layer microwave absorbing materials obtain excellent absorbing properties and show great design flexibility and diversity,which can be used as a suitable candidate for the preparation of favorable microwave absorbing cementitious materials.
基金funded by the National Natural Science Foundation of China(No.51904154)Natural Science Foundation of Hunan Province(No.2020JJ5491).
文摘The use of some environmental functional minerals as backfill-modified materials may improve the leaching resistance of cemented uranium tailings backfill created from alkali-activated slag(CUTB),but these materials may participate in the hydration reaction of the cementitious materials,which could have a certain impact on the pore structure of the CUTB,thus affecting its mechanical properties and leaching resistance.In this paper,natural zeolite is selected as the backfill-modified material,and it is added to alkali-activated slag paste(AASP)and CUTB in cementitious material proportions of 4%,8%,12%,and 16%to prepare AASP mixtures and CUTB mixtures containing environmental functional minerals.After the addition of natural zeolite,the porosity of the CUTB generally increases,but when the content is 4%,the porosity decreases to 22.30%.The uniaxial compressive strength(UCS)of the CUTB generally decreases,but the decrease is the smallest when the content is 4%,and the UCS is 12.37 MPa.The addition of natural zeolite mainly reduces the number of fine pores in the CUTB,but the pores with relaxation times T_(2)of greater than 10 ms account for about 10%of the total pores,and there are a certain number of large pores in the CUTB.The main product of alkali-activated slag is calcium(alumino)silicate hydrate(C-(A)-S-H gel).When natural zeolite is added,the hydration products develop towards denser products with a high degree of polymerization and the formation of low polymerization products is reduced.This affects the internal fracture pores of the hydration products and the interface pores of the CUTB,has an irregular effect on the pore characteristics of the CUTB,and influences the UCS.
基金financially supported by the National Key Research and Development Program of China(Grant No.2023YFC3200026)the National Natural Science Foundation of China(Grant No.U2243238)。
文摘Channel avulsion is a natural phenomenon that occurs abruptly on alluvial river deltas,which can affect the channel stability.The causes for avulsion could be generally categorized as topography-and flood-driven factors.However,previous studies on avulsion thresholds usually focused on topography-driven factors due to the centurial or millennial avulsion timescales of the world’s most deltas,but neglected the impacts of flood-driven factors.In the current study,a novel demarcation equation including the two driven factors was proposed,with the decadal timescale of avulsion being considered in the Yellow River Estuary(YRE).In order to quantify the contributions of different factors in each category,an entropy-based methodology was used to calculate the contributing weights of these factors.The factor with the highest weight in each category was then used to construct the demarcation equation,based on avulsion datasets associated with the YRE.An avulsion threshold was deduced according to the demarcation equation.This avulsion threshold was then applied to conduct the risk assessment of avulsion in the YRE.The results show that:two dominant factors cover respectively geomorphic coefficient representing the topography-driven factor and fluvial erosion intensity representing the flood-driven factor,which were thus employed to define a two dimensional mathematical space in which the demarcation equation can be obtained;the avulsion threshold derived from the equation was also applied in the risk assessment of avulsion;and the avulsion threshold proposed in this study is more accurate,as compared with the existing thresholds.