The flotation separation of chalcopyrite and talc is challenging due to their similar natural floatability characteristics.Besides,it is usually difficult to effectively inhibit talc by adding sodium carboxymethyl cel...The flotation separation of chalcopyrite and talc is challenging due to their similar natural floatability characteristics.Besides,it is usually difficult to effectively inhibit talc by adding sodium carboxymethyl cellulose(CMC)alone during chalcopyrite flotation.Here,a combined inhibitor comprising acidified sodium silicate(ASS)and CMC was employed to realize effective flotation separation of chalcopyrite and talc,and the combined inhibition mechanism was further investigated.Microflotation results showed that adding ASS strengthened the inhibitory effect of CMC on talc and improved the separation of chalcopyrite and talc.The zeta potential,Fourier transform infrared,and X-ray photoelectron spectroscopy analysis indicated that CMC was mainly adsorbed on the talc surface via hydroxyl and carboxyl groups.Moreover,the addition of ASS improved the adsorption of carboxyl groups.Furthermore,the adsorption experiments and apparent viscosity measurements revealed that adding ASS dispersed the pulp well,which reduced the apparent viscosity,improved the adsorption amount of CMC on the talc surface,and enhanced the inhibition of talc in chalcopyrite flotation.展开更多
Organic depressants have low selectivity in separating molybdenite and talc because their metal sites lack activity for organics chemisorption.In this study,surface modification by copper sulfate was used to induce th...Organic depressants have low selectivity in separating molybdenite and talc because their metal sites lack activity for organics chemisorption.In this study,surface modification by copper sulfate was used to induce the differential adsorption of pectin onto molybdenite and talc surfaces for enhanced flotation separation.Contact-angle experiments,scanning electron microscopy,adsorption measurements,timeof-flight secondary-ion mass spectrometry,and X-ray photoelectron spectroscopy analyses were conducted to reveal the interaction mechanism.Results illustrated that molybdenite and talc could not be separated using pectin alone,while molybdenite was selectively depressed after surface modification by copper sulfate and this effect was strengthened under alkaline conditions.Metal sites(Mg,Si and Mo)of talc and molybdenite themselves were unable to react with pectin,whereas Cu+would deposit and further function as active site for pectin chemisorption after surface modification.However,the quantity of deposited Cu sites dropped on talc surface and increased on molybdenite surface with increased pH,and the Mo atoms of molybdenite crystal were activated to take part in pectin chemisorption.Therefore,more pectin was adhered on molybdenite surface,which imparted molybdenite stronger wettability.Herein,surface-modification through metal ions can enable the differential adsorption of organic depressants and enhance the flotation separation of minerals.展开更多
The depression behavior and mechanism of guar gum on talc-type scheelite flotation were systematically investigated by flotation experiments, adsorption tests, zeta-potential measurements, and infrared spectroscopic a...The depression behavior and mechanism of guar gum on talc-type scheelite flotation were systematically investigated by flotation experiments, adsorption tests, zeta-potential measurements, and infrared spectroscopic analyses. The flotation results for monominerals, mixed minerals, and actual mineral samples indicated that guar gum exhibited much higher selective depression for talc than for scheelite. Bench-scale closed-circuit tests showed that a tungsten concentrate with a WO_3 grade of 51.43% and a WO_3 recovery of 76.18% was obtained. Adsorption tests, zeta-potential measurements, and infrared spectral analyses confirmed that guar gum absorbed more strongly onto the talc surface than onto the scheelite surface because of chemisorption between guar gum and talc. This chemisorption is responsible for the guar gum's highly selective depression for talc and small depression for scheelite. The flotation results provide technical support for talc-type scheelite flotation.展开更多
Talc is a hydroxyled, magnesium-rich, layered silicate that has the ideal chemical formula Mg3Si4O10(OH)2. Due to its unique properties, such as softness, chemical inertness, high thermal stability, low electrical con...Talc is a hydroxyled, magnesium-rich, layered silicate that has the ideal chemical formula Mg3Si4O10(OH)2. Due to its unique properties, such as softness, chemical inertness, high thermal stability, low electrical conductivity, lamellar habit, adsorption properties, and occurrence of a wide range of particle sizes that can be easily reduced by milling and high specific surface area, talc is widely used in many industries. A stratified deposit of unusual black talc, an occurrence of talc estimated to be more than half a billion tons, was found exposed in the late Neoproterozoic Dengying Formation, located in Guangfeng County, Jiangxi Province, southeastern China. The ores occur primarily as oolitic structures (Fig. 1). The mineralogical and geochemical characteristics of the ores were investigated by using multiple techniques. The ores were found to mainly consist of talc (30%–70%), dolomite, quartz, and magnesite. Most of talc crystals are ultrafine (with an average crystallite size of smaller than 5 μm) and appear as irregular broken or distorted lamellar flakes. The total organic carbon (TOC) content of the black talc ore samples is generally lower than 1.0%. Electron-microprobe analysis (EPMA) revealed low contents of Na, K, Ca and Mn, Fe, Ni, Al in the talc oolitic particles. The talc ores have low contents of toxic elements and relatively high contents of Li and Zn. The infrared spectrum of the black talc is similar to that of white talc from Trimouns (Pyrenees, France), and their Brunauer–Emmett-Teller (BET) specific surface areas, ranging from 15.7 to 23.2 m2/g, is much higher than those of white talc (normally lower than 5.0 m2/g), which may be due to the small size of the talc crystals.展开更多
The grinding of ultra-fine talcum powder and its application in a polypropylene (PP) matrix were investigated. Ultra-fine talcum powder was prepared by adjusting the grinding parameters of the physical milling proce...The grinding of ultra-fine talcum powder and its application in a polypropylene (PP) matrix were investigated. Ultra-fine talcum powder was prepared by adjusting the grinding parameters of the physical milling process. The talcum powder exhibited polymodal distribution. The layered morphology of talcum particles in a horizontal sand mill was rarely damaged or destroyed. PP-talcum nanocomposites were prepared by melt blending using a twin-screw extruder. Nano talcum can be seen as a single particle, although it is not very apparent. The bending strength of talcum-filled PP was gradually increased by approximately 28%. The impact strength linearly decreased as the filler weight ratio increased. The overall maximum improvement in mechanical properties was recorded when the filler ratios increased from 15 wt% to 20 wt%.展开更多
An experiment of producing high density polyethylene (HDPE) nano-composite filled with 4wt.% talc was presented. Acting as filler and a reinforcing agent in the HDPE, talc powder, sized at around 5 μm, was surface-tr...An experiment of producing high density polyethylene (HDPE) nano-composite filled with 4wt.% talc was presented. Acting as filler and a reinforcing agent in the HDPE, talc powder, sized at around 5 μm, was surface-treated with aluminum diethylene glycol dinitrate coupling agent before adding to the HDPE. Analyses of the reinforced HDPE nano-composite show significant improvement in its mechanical properties including, tensile strength (>26 MPa), break elongation (<1.1%), flexural strength (>22 MPa), and friction coefficients<0.11. The results demonstrate that, after surface-treated, talc can be used as a promising filling material and a reinforcing agent in making HDPE nano-composite.展开更多
Homogeneous cordierite has been synthesized at low cost by talc-magnesite and coal gangue as the main raw materials. The mechanism of synthesizing cordierite under such a composing system of raw materials, and the eff...Homogeneous cordierite has been synthesized at low cost by talc-magnesite and coal gangue as the main raw materials. The mechanism of synthesizing cordierite under such a composing system of raw materials, and the effect of temperature on the crystal cell parameters and microstructure and thermal expansion coefficient of cordierite crystal have been studied via testing methods of XRD, SEM, etc. The result shows that the homogeneous cordierite can be synthesized by the systematic composing materials of "talc-magnesite-coal gangue-talc" with heat pre-servation at 1350 ℃ for 1 h; as the keeping time is prolonged, Al^3+ and Mg^2+ in cordierite crystal are replaced by a few impurity ions such as Fe^3+, Fe^2+, etc., and the crystal cell parameters of cordierite present an increase trend; as the high-temperature heat preservation is prolonged, the content of glassy phase in the sample is increased, its density is improved, and its thermal expansion coefficient presents an increase trend.展开更多
The utilization of Ca ion as assistant depressant of CMC on talc has been widely reported.Thus,the study on the adsorption mechanism of Ca ion on talc surface is very crucial for understanding the performance of CMC o...The utilization of Ca ion as assistant depressant of CMC on talc has been widely reported.Thus,the study on the adsorption mechanism of Ca ion on talc surface is very crucial for understanding the performance of CMC on talc depression.In this paper,mechanism insights into hydrated Ca ion adsorption on talc(001) basal surface were creatively provided using DFT calculation.[Ca(H_(2)O)_6]^(2+) and [Ca(OH)(H_(2)O)_(3)]^(+) were determined as the effective hydrate components for Ca ion adsorption,and the top O site was the most favorable position for their adsorptions on talc surface.Furthermore,the adsorption mechanisms of [Ca(H_(2)O)_6]^(2+) and [Ca(OH)(H_(2)O)_(3)]^(+) on talc surface were found to be not the Ca-O chemical bond,but the hydrogen bonding formed by the H atom of the H_(2)O ligand and the surface O atom.H_(2)O acted like a bridge to connect them to the talc surface.Moreover,the hydrogen bonding was formed due to the hybridization of H 1s orbital with the O 2s,O 2p orbitals.Simultaneously,electrons transferred between the H atom and the surface O atom.This work provides theoretical insights into the Ca ion adsorption on talc surface,which can help deeply understand the talc flotation using CMC as depression.展开更多
Deep investigation boreholes in crystalline rock for site selection of repositories for high-level radioactive waste are proposed to be sealed by installing a series of dense concrete and clay plugs. These should prev...Deep investigation boreholes in crystalline rock for site selection of repositories for high-level radioactive waste are proposed to be sealed by installing a series of dense concrete and clay plugs. These should prevent radionuclides from leaking canisters at depth to migrate to the biosphere through the holes. The concrete seals will be installed where the holes intersect water-bearing fracture zones to serve as stable and low-permeable supports for adjacent clay plugs. Low porosity and microstructural stability must be guaranteed for many thousands of years and ordinary Portland cement with organic superplastizer will not fulfill the requirements since the high pH will cause degradation of contacting clay and the organic additive can produce colloids with a capacity to carry radionuclides up to the biosphere. Very cement-poor concrete (展开更多
The possibility of using a centrifugal-gravity concentrator to reject Mg-bearing minerals and minimize metal losses in the flotation of base metals was evaluated. Sample characterization, batch scoping tests, pilot-sc...The possibility of using a centrifugal-gravity concentrator to reject Mg-bearing minerals and minimize metal losses in the flotation of base metals was evaluated. Sample characterization, batch scoping tests, pilot-scale tests, and regrind-flotation tests were conducted on a Ni flotation tailings stream. Batch tests revealed that the Mg grade decreased dramatically in the concentrate products. Pilot-scale testing of a continuous centrifugal concentrator(Knelson CVD6) on the flotation tailings revealed that a concentrate with a low mass yield, low Mg content, and high Ni upgrade ratio could be achieved. Under optimum conditions, a concentrate at 6.7% mass yield was obtained with 0.85% Ni grade at 12.9% Ni recovery and with a low Mg distribution(1.7%). Size partition curves demonstrated that the CVD also operated as a size classifier, enhancing the rejection of talc fines. Overall, the CVD was capable of rejecting Mg-bearing minerals. Moreover, an opportunity exists for the novel use of centrifugal-gravity concentration for scavenging flotation tailings and/or after comminution to minimize amount of Mg-bearing minerals reporting to flotation.展开更多
The Xiuyan Jade samples were treated under thermal conditions. By polarizing microscope, the three kinds of jade were choosed. With DTA-TG analysis, three transition temperatures were obtained which were 600℃, 770℃ ...The Xiuyan Jade samples were treated under thermal conditions. By polarizing microscope, the three kinds of jade were choosed. With DTA-TG analysis, three transition temperatures were obtained which were 600℃, 770℃ and 840℃. The study interpreted the mechanism of Xiuyan Jade under thermal condition through XRD analysis results. The mechanism of antigorite thermal activation was as following: when the temperature reached 600℃, the hydroxyl in octahedral sheet began dehydrating, and the new mineral phase forsterite was found, but the layer structure was maintained; when the temperature reached 770℃, the layer structure of antigorite was destroyed; when the temperature reached 840℃, the crystallinity of forsterite was improved, then another new mineral phase enstatite appeard. For talc, it was likely turn to enstatite directly while the temperature rising, and the appearance of SiO2 was most likely due to the conversion of talc.展开更多
The effect of solution surface tension on the flotation behavior of natural hydrophobic minerals such as graphite and talc is studied. The best sol- ution surface tension range is also given in the graphite and talc f...The effect of solution surface tension on the flotation behavior of natural hydrophobic minerals such as graphite and talc is studied. The best sol- ution surface tension range is also given in the graphite and talc flotation. And the critical sur- face tension distribution of floatability of them is analysed.展开更多
Talc coatings were produced with chemical method on the surface of pure aluminum. The characteristics of cathodic polarization in a 3.5% NaCl solution have been studied through the observation of the 'current osci...Talc coatings were produced with chemical method on the surface of pure aluminum. The characteristics of cathodic polarization in a 3.5% NaCl solution have been studied through the observation of the 'current oscillations' phenomenon.展开更多
基金financially supported by the National Natural Science Foundation of China (Nos.52104266 and 52074206)Open Foundation of State Key Laboratory of Mineral Processing (No.BGRIMM-KJSKL-2021-19)+2 种基金the Natural Science Basic Research Program of Shaanxi Province (No.2021JQ-507)the Natural Science Project of Shaanxi Education Department (No.21JK0731)Key Research and Development Projects of Anhui Province (No.202104a07020012)。
文摘The flotation separation of chalcopyrite and talc is challenging due to their similar natural floatability characteristics.Besides,it is usually difficult to effectively inhibit talc by adding sodium carboxymethyl cellulose(CMC)alone during chalcopyrite flotation.Here,a combined inhibitor comprising acidified sodium silicate(ASS)and CMC was employed to realize effective flotation separation of chalcopyrite and talc,and the combined inhibition mechanism was further investigated.Microflotation results showed that adding ASS strengthened the inhibitory effect of CMC on talc and improved the separation of chalcopyrite and talc.The zeta potential,Fourier transform infrared,and X-ray photoelectron spectroscopy analysis indicated that CMC was mainly adsorbed on the talc surface via hydroxyl and carboxyl groups.Moreover,the addition of ASS improved the adsorption of carboxyl groups.Furthermore,the adsorption experiments and apparent viscosity measurements revealed that adding ASS dispersed the pulp well,which reduced the apparent viscosity,improved the adsorption amount of CMC on the talc surface,and enhanced the inhibition of talc in chalcopyrite flotation.
基金The authors would like to acknowledge the support from the National Natural Science Foundation of China(No.52174272)the Joint Funds of the National Natural Science Foundation of China(No.U1704252)+1 种基金the Fundamental Research Funds for the Central Universities of Central South University(Nos.2021zzts0306 and 2021zzts0896)the Hunan Provincial Natural Science Foundation of China(No.2020JJ5736).
文摘Organic depressants have low selectivity in separating molybdenite and talc because their metal sites lack activity for organics chemisorption.In this study,surface modification by copper sulfate was used to induce the differential adsorption of pectin onto molybdenite and talc surfaces for enhanced flotation separation.Contact-angle experiments,scanning electron microscopy,adsorption measurements,timeof-flight secondary-ion mass spectrometry,and X-ray photoelectron spectroscopy analyses were conducted to reveal the interaction mechanism.Results illustrated that molybdenite and talc could not be separated using pectin alone,while molybdenite was selectively depressed after surface modification by copper sulfate and this effect was strengthened under alkaline conditions.Metal sites(Mg,Si and Mo)of talc and molybdenite themselves were unable to react with pectin,whereas Cu+would deposit and further function as active site for pectin chemisorption after surface modification.However,the quantity of deposited Cu sites dropped on talc surface and increased on molybdenite surface with increased pH,and the Mo atoms of molybdenite crystal were activated to take part in pectin chemisorption.Therefore,more pectin was adhered on molybdenite surface,which imparted molybdenite stronger wettability.Herein,surface-modification through metal ions can enable the differential adsorption of organic depressants and enhance the flotation separation of minerals.
基金financially supported by the National Natural Science Foundation of China (No.51404218)the National Key Technology R&D Program (No.2015BAB12B02)the Science and Technology Planning Project of Guangdong Province, China (No.2013B090800016)
文摘The depression behavior and mechanism of guar gum on talc-type scheelite flotation were systematically investigated by flotation experiments, adsorption tests, zeta-potential measurements, and infrared spectroscopic analyses. The flotation results for monominerals, mixed minerals, and actual mineral samples indicated that guar gum exhibited much higher selective depression for talc than for scheelite. Bench-scale closed-circuit tests showed that a tungsten concentrate with a WO_3 grade of 51.43% and a WO_3 recovery of 76.18% was obtained. Adsorption tests, zeta-potential measurements, and infrared spectral analyses confirmed that guar gum absorbed more strongly onto the talc surface than onto the scheelite surface because of chemisorption between guar gum and talc. This chemisorption is responsible for the guar gum's highly selective depression for talc and small depression for scheelite. The flotation results provide technical support for talc-type scheelite flotation.
文摘Talc is a hydroxyled, magnesium-rich, layered silicate that has the ideal chemical formula Mg3Si4O10(OH)2. Due to its unique properties, such as softness, chemical inertness, high thermal stability, low electrical conductivity, lamellar habit, adsorption properties, and occurrence of a wide range of particle sizes that can be easily reduced by milling and high specific surface area, talc is widely used in many industries. A stratified deposit of unusual black talc, an occurrence of talc estimated to be more than half a billion tons, was found exposed in the late Neoproterozoic Dengying Formation, located in Guangfeng County, Jiangxi Province, southeastern China. The ores occur primarily as oolitic structures (Fig. 1). The mineralogical and geochemical characteristics of the ores were investigated by using multiple techniques. The ores were found to mainly consist of talc (30%–70%), dolomite, quartz, and magnesite. Most of talc crystals are ultrafine (with an average crystallite size of smaller than 5 μm) and appear as irregular broken or distorted lamellar flakes. The total organic carbon (TOC) content of the black talc ore samples is generally lower than 1.0%. Electron-microprobe analysis (EPMA) revealed low contents of Na, K, Ca and Mn, Fe, Ni, Al in the talc oolitic particles. The talc ores have low contents of toxic elements and relatively high contents of Li and Zn. The infrared spectrum of the black talc is similar to that of white talc from Trimouns (Pyrenees, France), and their Brunauer–Emmett-Teller (BET) specific surface areas, ranging from 15.7 to 23.2 m2/g, is much higher than those of white talc (normally lower than 5.0 m2/g), which may be due to the small size of the talc crystals.
基金Funded by the Foundation of Shanghai Science and Technology Committee (Nos.10521100602, 10DZ2211400)Foundation of Guangdong Province (No.2011A090200082)China Postdoctoral Science Foundation, and Research Foundation for the Excellent Youth Scholars of Shanghai(No.SHU-10057)
文摘The grinding of ultra-fine talcum powder and its application in a polypropylene (PP) matrix were investigated. Ultra-fine talcum powder was prepared by adjusting the grinding parameters of the physical milling process. The talcum powder exhibited polymodal distribution. The layered morphology of talcum particles in a horizontal sand mill was rarely damaged or destroyed. PP-talcum nanocomposites were prepared by melt blending using a twin-screw extruder. Nano talcum can be seen as a single particle, although it is not very apparent. The bending strength of talcum-filled PP was gradually increased by approximately 28%. The impact strength linearly decreased as the filler weight ratio increased. The overall maximum improvement in mechanical properties was recorded when the filler ratios increased from 15 wt% to 20 wt%.
文摘An experiment of producing high density polyethylene (HDPE) nano-composite filled with 4wt.% talc was presented. Acting as filler and a reinforcing agent in the HDPE, talc powder, sized at around 5 μm, was surface-treated with aluminum diethylene glycol dinitrate coupling agent before adding to the HDPE. Analyses of the reinforced HDPE nano-composite show significant improvement in its mechanical properties including, tensile strength (>26 MPa), break elongation (<1.1%), flexural strength (>22 MPa), and friction coefficients<0.11. The results demonstrate that, after surface-treated, talc can be used as a promising filling material and a reinforcing agent in making HDPE nano-composite.
基金This work was supported by the National Natural Science Foundation of China (50672056) Scientific Research and Innovation Foundation of Shaanxi University of Science & Technology (SUST-B14)
文摘Homogeneous cordierite has been synthesized at low cost by talc-magnesite and coal gangue as the main raw materials. The mechanism of synthesizing cordierite under such a composing system of raw materials, and the effect of temperature on the crystal cell parameters and microstructure and thermal expansion coefficient of cordierite crystal have been studied via testing methods of XRD, SEM, etc. The result shows that the homogeneous cordierite can be synthesized by the systematic composing materials of "talc-magnesite-coal gangue-talc" with heat pre-servation at 1350 ℃ for 1 h; as the keeping time is prolonged, Al^3+ and Mg^2+ in cordierite crystal are replaced by a few impurity ions such as Fe^3+, Fe^2+, etc., and the crystal cell parameters of cordierite present an increase trend; as the high-temperature heat preservation is prolonged, the content of glassy phase in the sample is increased, its density is improved, and its thermal expansion coefficient presents an increase trend.
基金supported in part by the High Performance Computing Center of Central South Universityfinancially supported by the National Natural Science Foundation of China (No.51674291)。
文摘The utilization of Ca ion as assistant depressant of CMC on talc has been widely reported.Thus,the study on the adsorption mechanism of Ca ion on talc surface is very crucial for understanding the performance of CMC on talc depression.In this paper,mechanism insights into hydrated Ca ion adsorption on talc(001) basal surface were creatively provided using DFT calculation.[Ca(H_(2)O)_6]^(2+) and [Ca(OH)(H_(2)O)_(3)]^(+) were determined as the effective hydrate components for Ca ion adsorption,and the top O site was the most favorable position for their adsorptions on talc surface.Furthermore,the adsorption mechanisms of [Ca(H_(2)O)_6]^(2+) and [Ca(OH)(H_(2)O)_(3)]^(+) on talc surface were found to be not the Ca-O chemical bond,but the hydrogen bonding formed by the H atom of the H_(2)O ligand and the surface O atom.H_(2)O acted like a bridge to connect them to the talc surface.Moreover,the hydrogen bonding was formed due to the hybridization of H 1s orbital with the O 2s,O 2p orbitals.Simultaneously,electrons transferred between the H atom and the surface O atom.This work provides theoretical insights into the Ca ion adsorption on talc surface,which can help deeply understand the talc flotation using CMC as depression.
文摘Deep investigation boreholes in crystalline rock for site selection of repositories for high-level radioactive waste are proposed to be sealed by installing a series of dense concrete and clay plugs. These should prevent radionuclides from leaking canisters at depth to migrate to the biosphere through the holes. The concrete seals will be installed where the holes intersect water-bearing fracture zones to serve as stable and low-permeable supports for adjacent clay plugs. Low porosity and microstructural stability must be guaranteed for many thousands of years and ordinary Portland cement with organic superplastizer will not fulfill the requirements since the high pH will cause degradation of contacting clay and the organic additive can produce colloids with a capacity to carry radionuclides up to the biosphere. Very cement-poor concrete (
文摘The possibility of using a centrifugal-gravity concentrator to reject Mg-bearing minerals and minimize metal losses in the flotation of base metals was evaluated. Sample characterization, batch scoping tests, pilot-scale tests, and regrind-flotation tests were conducted on a Ni flotation tailings stream. Batch tests revealed that the Mg grade decreased dramatically in the concentrate products. Pilot-scale testing of a continuous centrifugal concentrator(Knelson CVD6) on the flotation tailings revealed that a concentrate with a low mass yield, low Mg content, and high Ni upgrade ratio could be achieved. Under optimum conditions, a concentrate at 6.7% mass yield was obtained with 0.85% Ni grade at 12.9% Ni recovery and with a low Mg distribution(1.7%). Size partition curves demonstrated that the CVD also operated as a size classifier, enhancing the rejection of talc fines. Overall, the CVD was capable of rejecting Mg-bearing minerals. Moreover, an opportunity exists for the novel use of centrifugal-gravity concentration for scavenging flotation tailings and/or after comminution to minimize amount of Mg-bearing minerals reporting to flotation.
基金Supported by National Natural Science Foundation (Grant No.:40872045 41172047)The Opening Project of Key Laboratory of Solid Waste Treatment and Resource Recycle (SWUST), Ministry of Education (12zxgk01)
文摘The Xiuyan Jade samples were treated under thermal conditions. By polarizing microscope, the three kinds of jade were choosed. With DTA-TG analysis, three transition temperatures were obtained which were 600℃, 770℃ and 840℃. The study interpreted the mechanism of Xiuyan Jade under thermal condition through XRD analysis results. The mechanism of antigorite thermal activation was as following: when the temperature reached 600℃, the hydroxyl in octahedral sheet began dehydrating, and the new mineral phase forsterite was found, but the layer structure was maintained; when the temperature reached 770℃, the layer structure of antigorite was destroyed; when the temperature reached 840℃, the crystallinity of forsterite was improved, then another new mineral phase enstatite appeard. For talc, it was likely turn to enstatite directly while the temperature rising, and the appearance of SiO2 was most likely due to the conversion of talc.
文摘The effect of solution surface tension on the flotation behavior of natural hydrophobic minerals such as graphite and talc is studied. The best sol- ution surface tension range is also given in the graphite and talc flotation. And the critical sur- face tension distribution of floatability of them is analysed.
文摘Talc coatings were produced with chemical method on the surface of pure aluminum. The characteristics of cathodic polarization in a 3.5% NaCl solution have been studied through the observation of the 'current oscillations' phenomenon.