Simulation on an optimal combustion control strategy for 3-D temperature distributions in tangentially pc-fired utility boiler furnaces

The control of 3-D temperature distribution in a utility boiler furnace is essential for the safe, economic and clean operation of pc-fired furnace with multi-burner system. The development of the visualization of 3-D temperature distributions in pc-fired furnaces makes it possible for a new combustion control strategy directly with the furnace temperature as its goal to improve the control quality for the combustion processes. Studied in this paper is such a new strategy that the whole furnace is divided into several parts in the vertical direction, and the average temperature and its bias from the center in every cross section can be extracted from the visualization results of the 3-D temperature distributions. In the simulation stage, a computational fluid dynamics(CFD) code served to calculate the 3-D temperature distributions in a furnace, then a linear model was set up to relate the features of the temperature distributions with the input of the combustion processes, such as the flow rates of fuel and air fed into the furnaces through all the burners. The adaptive genetic algorithm was adopted to find the optimal combination of the whole input parameters which ensure to form an optimal 3-D temperature field in the furnace desired for the operation of boiler. Simulation results showed that the strategy could soon find the factors making the temperature distribution apart from the optimal state and give correct adjusting suggestions.

Effect of contact thermal resistance on temperature distributions of concrete-filled steel tubes in fire

To predicate the temperature distribution of concrete-filled steel tubes(CFSTs) being exposure to fire,a finite element analysis model was developed using a finite element package,ANSYS.A suggested value of contact thermal resistance was therefore proposed with the supporting of massive numbers of collected test data.Parametric analysis was conducted subsequently towards the cross-sectional temperature distribution of CFST columns in four-side fire,in which the exposure time,width of the cross section,steel ratio were taken into account with considering contact thermal resistance.It was found that contact thermal resistance has little effect on the overall temperature regulation with the exposure time,the width of cross-section or the change of steel ratio.However,great temperature dropping at the concrete adjacent to the contact interface,and gentle temperature increase at steel tube,exist if considering contact thermal resistance.The results of the study are expected to provide theoretical basis for the fire resistance behavior and design of the CFST columns being exposure to fire.

Temperature distributions in concrete box girders due to heat of concrete hydration

Based on heat transfer theory,a two-dimensional complex exponential function was used to compute heat of concrete hydration.A concrete box girder consisting of a single box with two cells used on Harbin Songpu Bridge was measured on site.The two coefficients in the complex exponential function were determined to best fit the field measured data.ABAQUS program was used to simulate the heat transfer and determine the temperature distribution in the concrete box girders during concrete setting.The calculated temperature distribution in the box girders were compared with the field measured data and good agreement was observed.The temperature distribution and gradient in the entire box section,webs and bottom slab were analyzed using the measured and calculated results during the course of concrete hydration.

Study on visualization simulation of temperature distributions in surrounding rock of tunnels in a deep mine

Based on the mathematical model for rock temperature distribution in a geo-thermal field,the properties of rock temperature distribution in geothermal field for fourkinds of surrounding rock cross-sections of tunnels in a deep mine were simulated by us-ing finite element method.It is shown that the relationship for rock temperature distributionvaried with the geothermal parameters,time and space.Namely, 2-dimensionaltime-dependent isograms clearly showed the process for rock temperature variation anddistribution in a geothermal field which has been redisplayed with visualization numericalsimulation.

Analysis on Temperature Distributions in Single Cell of Polymer Electrolyte Fuel Cell When Operated in High Temperature Range

This study is to understand the impact of operating condition, especially initial operation temperature （Tini） which is set in high temperature range, on the temperature profile of the interface between PEM （polymer electrolyte membrane） and catalyst layer at the cathode （i.e., the reaction surface） in a single PEFC （polymer electrolyte fuel cell）. A 1D multi-plate heat transfer model based on the temperature data of separator measured using thermograph in a power generation experiment was developed to evaluate the reaction surface temperature （Treact）. This study investigated the effects of flow rate, relative humidity and type of supply gas as well as Tini on the temperature distribution on reaction surface. The results obtained in 02 supply case show that, the temperature rise at the segments near the outlet of cell decreases with increasing Tini irrespective of relative humidity of supply gas （RH）, while it is not seen in air supply case. Regarding the segments except near the outlet in 02 supply case, Treact - Tini increases with increasing Tini for 40% RH. The temperature distribution on reaction surface in 02 supply case is wider with increasing Tini as well as decreasing RH, though that in air supply case is relatively even.

Impact of Thickness of Polymer Electrolyte Membrane on Temperature Distributions in Single Cell of Polymer Electrolyte Fuel Cell Operated at High Temperature

This study is to understand the impact of operating condition, especially initial operation temperature （Tini） which is set in high temperature range, on the temperature profile of the interface between PEM （polymer electrolyte membrane） and catalyst layer at the cathode （i.e., the reaction surface） in a single PEFC （polymer electrolyte fuel cell）. A 1D multi-plate heat transfer model based on the temperature data of separator measured using thermograph in a power generation experiment was developed to evaluate the reaction surface temperature （Treact）. This study investigated the effects of Tini, flow rate and relative humidity of supply gas as well as thickness of PEM on the temperature distribution on reaction surface. As a result, the impact of flow rate of supply gas on the temperature distribution is not significant irrespective of relative humidity conditions as well as PEM type. When operated at high temperature, the temperature distribution is relatively flat in the case of thicker PEM （Nafion 115）, while Treact rises from the inlet to the outlet large and the temperature distribution is wide in the case of thin PEM （Nafion 211） irrespective of relative humidity condition. Since the water transfer through PEM in the case of Nafion 211 is better than Nafion 115 due to thin PEM, the power generation is promoted along the gas flow with the aid of humidification by water produced from electrochemical reaction.

Numerical Analysis of Temperature Distributions in Single Cell of Polymer Electrolyte Fuel Cell when Operated in Elevated Temperature Range

Abstract： The purpose of this study is to analyze the temperature distribution on the interface between the polymer electrolyte membrane and catalyst layer at the cathode in single cell of polymer electrolyte fuel cell when operated in elevated temperature range than usual. In this study, the interface between the polymer electrolyte membrane and catalyst layer at the cathode is named as reaction surface. This study has considered the 1D multi-plate heat transfer model estimating the temperature distribution on the reaction surface and verified with the 3D numerical simulation model solving many governing equations on the coupling phenomena of the polymer electrolyte fuel cell. The 3D numerical simulation model coverers a half size of actual cell including three straight parts and two turn-back corners, which can display the essential phenomena of single cell. The results from both models/simulations agreed well. The effects of initial operation temperature, flow rate, and relative humidity of supply gas on temperature distribution on the reaction surface have been investigated. Though the effect of flow rate of supply gas on temperature distribution on reaction surface has been small, low relative humidity of supply gas has caused higher temperature on the reaction surface compared to high relative humidity of the supply gas. The temperature rise of reaction surface from initial operation temperature has increased with the increasing in initial operation temperature of cell.

Impact of Relative Humidity of Supply Gas on Temperature Distributions in Single Cell of Polymer Electrolyte Fuel Cell When Operated at High Temperature

For improving the performance of stationary PEFC （polymer electrolyte fuel cell） system, the cell operating temperature up to 90℃ will be preferred in Japan during the period from 2020 to 2030. To understand the operation of the PEFC system under relatively high temperature conditions, detail heat and mass transfer analysis is required. The purpose of this study is to analyze the impact of relative humidity of supply gas on temperature distribution on the backside of separator in single ceil of PEFC using Nation membrane at higher temperature e.g. 90℃. The in-plane temperature distribution when power was being generated was measured using thermograph with various relative humidity of supply gases. It was found that the in-plane temperature distribution at the anode was more even than that at the cathode irrespective of the relative humidity of supply gas at the anode and the cathode. The temperature elevated along gas flow through the gas channel at the cathode irrespective of relative humidity of supply gas at the anode and the cathode. The in-plane temperature distribution at the cathode was narrower with the increase in Tini irrespective of relative humidity of supply gas at the cathode, while it was not observed when changing the relative humidity of supply gas at the anode. When the relative humidity of supply gas at cathode decreased, the in-plane temperature distribution at the anode was wider compared to decreasing the relative humidity of supply gas at the anode. The study concluded that the impact of relative humidity of supply gas at both anode and cathode had little impact on the in-plane temperature distribution at the cathode.

Study on Temperature Distribution and Smoke Spreading Behavior of Different Fire Source Locations in the UnderwaterW-Shaped Island-Crossing Tunnel

Called island-crossing tunnels,some specific underwater tunneling projects face constraints imposed by geological and water conditions,necessitating their passage through artificial or natural islands.The longitudinal of the tunnel follows aW-shaped distribution.The congestion situation does not allowfor immediate longitudinal smoke exhaust at the early stage of the fire,and the natural spread of smoke is complicated.An exhaustive investigation was carried out to analyze the smoke behaviors during a fire incident,employing the fire dynamics software FDS,considering five slopes and four fire locations.The simulation results reveal that the layer of high-temperature smoke becomes thicker as one gets closer to the fire source.The thermal pressure difference significantly impacts the temperature distribution within the tunnel and the distance of smoke spread.The value of the thermal pressure difference is significantly affected by changes in slope.It reaches a maximum of 157 Pa at a 5%slope,while it is only 41 Pa at a 1%slope when the fire occurs at the V-point.Fire hazards vary across locations within the W-shaped tunnel,necessitating separate consideration of the V-point and inverted V-point fire characteristics.The mass flow rate in small and large slope tunnels shows different decay rates due to variations in the main forces acting on the movement.Hence,two equations have been developed to predict the smoke mass flow rate,indicating a nonlinear relationship with the tunnel slope and the distance fromthe fire source.The tunnel slope inversely affects the smoke mass flowrate at the same location.The results can be utilized as a reference for conducting evacuation operations and aiding rescues during aW-shaped tunnel fire.

Experimental study on pressure and temperature distributions for low mass flux steam jet in subcooled water

A low mass flux steam jet in subcooled water was experimentally investigated.The transition of flow pattern from stable jet to condensation oscillation was observed at relatively high water temperature.The axial total pressures,the axial and radial temperature distributions were measured in the jet region.The results indicated that the pressure and temperature distributions were mainly influenced by the water temperature.The correlations corrected with water temperature were given to predict the dimen-sionless axial pressure peak distance and axial temperature distributions in the jet region,the results showed a good agreement between the predictions and experiments.Moreover,the self-similarity property of the radial temperature was obtained,which agreed well with Gauss distribution.In present work,all the dimensionless properties were mainly dependent on the water temperature but weakly on the nozzle size under a certain steam mass flux.

Numerical investigation of water and temperature distributions in a proton exchange membrane electrolysis cell

A three-dimensional, non-isothermal, two-phase model for a PEM water electrolysis cell(PEMEC) is established in this study.An effective connection between two-phase transport and performance in the PEMECs is built through coupling the liquid water saturation and temperature in the charge conservation equation. The distributions of liquid water and temperature with different operating(voltage, temperature, inlet velocity) and physical(contact angle, and porosity of anode gas diffusion layer) parameters are examined and discussed in detail. The results show that the water and temperature distributions, which are affected by the operating and physical parameters, have a combined effect on the cell performance. The effects of various parameters on the PEMEC are of interaction and restricted mutually. As the voltage increases, the priority factor caused by the change of inlet water velocity changes from the liquid water saturation increase to the temperature drop in the anode catalyst layer. While the priority influence factor caused by the contact angle and porosity of anode gas diffusion layer is the liquid water saturation. Decreasing the contact angle or/and increasing the porosity can improve the PEMEC performance especially at the high voltage. The results can provide a better understanding of the effect of heat and mass transfer and the foundation for optimization design.

Simulation of Velocity and Temperature Distributions of Displacement Ventilation System with Single or Double Heat Sources

In order to obtain a better understanding of flow characteristics of displacement ventilation, the three-dimensional numerical models are developed using the CFD technology. The numerical simulation results are verified by experiments, based on this, the velocity and temperature distribution of three-dimensional displacement ventilation system with single and double heat sources are studied. Velocity and temperature fields under two different cases of heat source are analyzed and compared. The numerical results show that there are three layers in vertical temperature fields of displacement ventilation system with single or double heat sources, and the vertical temperature distribution of single heat source is different from that of double heat sources. When indoor load is large, the comfort requirement of people indoor can＇t be satisfied with displacement ventilation system only, thus an additional refrigeration system is necessary. Furthermore, under the condition of two heat sources, the displacement ventilation parameters can＇t be computed simply according to single heat source inlet parameters, therefore the interaction between heat sources should be considered.

Numerical simulation of temperature and strength distributions of mold(core) on heating

By using Visual C++, a model with post processing was carried out to simulate the temperature and strength distributions of the mold(core). The results are shown in 256 color graphic mode. With this model, the temperature and strength distributions of the mold(core) both in case of heating process for core in the furnace and solidification process for a thin wall aluminum alloy casting in the mold(core) are numerically simulated. The results show that the temperature and strength distributions of the mold(core) were uneven because the thermal conductivity of the resin sand was much small. This study laid a basis for the optimum design of the mold(core) properties. [

Thermal integrity profiling of cast-in-situ piles in sand using fiber-optic distributed temperature sensing

Defects in cast-in-situ piles have an adverse impact on load transfer at the pile‒soil interface and pile bearing capacity. In recent years, thermal integrity profiling (TIP) has been developed to measure temperature profiles of cast-in-situ piles, enabling the detection of structural defects or anomalies at the early stage of construction. However, using this integrity testing method to evaluate potential defects in cast-in-situ piles requires a comprehensive understanding of the mechanism of hydration heat transfer from piles to surrounding soils. In this study, small-scale model tests were conducted in laboratory to investigate the performance of TIP in detecting pile integrity. Fiber-optic distributed temperature sensing (DTS) technology was used to monitor detailed temperature variations along model piles in sand. Additionally, sensors were installed in sand to measure water content and matric suction. An interpretation method against available DTS-based thermal profiles was proposed to reveal the potential defective regions. It shows that the temperature difference between normal and defective piles is more obvious in wet sand. In addition, there is a critical zone of water migration in sand due to the water absorption behavior of cement and temperature transfer-induced water migration in the early-age concrete setting. These findings could provide important insight into the improvement of the TIP testing method for field applications.

Temperature field test and prediction using a GA-BP neural network for CRTS Ⅱ slab tracks

The CRTS Ⅱ slab track, which is connected in a longitudinal direction, is one of the main ballastless tracks in China, with approximately 7365 km of operational track. Temperature loading is a very vital factor leading to slab track damages such as warping and cracking. While existing research on temperature distribution rests on either site tests in special environments or theoretical analysis, the long-term temperature field characteristics are not clear. Therefore, a long-term temperature field test for the CRTS Ⅱ slab track on bridge-subgrade transition section was conducted to analyze the temperature field. A GA-BP(genetic algorithm optimized back propagation) neural network was trained on the test data to predict the temperature field. The vertical and lateral temperature distributions in four typical days were carried out. We found that the temperature along the track was distributed in a nonlinear manner. This was particularly distinct in the vertical direction for depths of less than 300 mm. The highest and lowest daily temperatures and the daily range of the temperature were analyzed. With the increasing depth, the daily highest temperatures and range of the temperature were smaller, the daily lowest temperatures were higher, and the time corresponding to this peak value appeared later in the day. Both the highest and lowest daily temperature could be predicted using the GA-BP neural network, though the accuracy in predicting the highest temperature was higher than that in predicting the lowest temperature.

Numerical Analysis on Temperature Distribution in a Single Cell of PEFC Operated at Higher Temperature by1D Heat Transfer Model and 3D Multi-Physics Simulation Model

This study is to understand the impact of operating conditions, especially initial operation temperature (Tini) which is set in a high temperature range, on the temperature profile of the interface between the polymer electrolyte membrane (PEM) and the catalyst layer at the cathode (i.e., the reaction surface) in a single cell of polymer electrolyte fuel cell (PEFC). A 1D multi-plate heat transfer model based on the temperature data of the separator measured using the thermograph in a power generation experiment was developed to evaluate the reaction surface temperature (Treact). In addition, to validate the proposed heat transfer model, Treact obtained from the model was compared with that from the 3D numerical simulation using CFD software COMSOL Multiphysics which solves the continuity equation, Brinkman equation, Maxwell-Stefan equation, Butler-Volmer equation as well as heat transfer equation. As a result, the temperature gap between the results obtained by 1D heat transfer model and those obtained by 3D numerical simulation is below approximately 0.5 K. The simulation results show the change in the molar concentration of O2 and H2O from the inlet to the outlet is more even with the increase in Tini due to the lower performance of O2 reduction reaction. The change in the current density from the inlet to the outlet is more even with the increase in Tini and the value of current density is smaller with the increase in Tini due to the increase in ohmic over-potential and concentration over-potential. It is revealed that the change in Treact from the inlet to the outlet is more even with the increase in Tini irrespective of heat transfer model. This is because the generated heat from the power generation is lower with the increase in Tini due to the lower performance of O2 reduction reaction.

Correlation Analysis of Wind Turbine Temperature Rise and Exergy Efficiency Based on Field-Path Coupling

To solve the problems of large losses and low productivity of permanent magnet synchronous generators used in wind power systems,the field-circuit coupling method is used to accurately solve the electromagnetic field and temperature field of the generator.The loss distribution of the motor is accurately obtained by considering the influence of external circuit characteristics on its internal physical field.By mapping the losses to the corresponding part of the three-dimensional finite element model of the motor,the temperature field is solved,and the global temperature distribution of the generator,considering the influence of end windings,is obtained.By changing the air gap length,permanent magnet thickness,and winding conductivity,the relationship between the loss,temperature rise,and exergy efficiency can be obtained.By optimizing the air gap length,permanent magnet thickness,and winding conductivity,the best configuration and material properties can improve the efficiency of the motor by up to 4%.

Numerical simulation of downhole temperature distribution in producing oil wells

An improved numerical simulation method is presented to calculate the downhole temperature distribution for multiple pay zones in producing oil wells. Based on hydrodynamics and heat transfer theory, a 2-D temperature field model in cylindrical coordinates is developed. In the model, we considered general heat conduction as well as the heat convection due to fluid flow from porous formation to the borehole. We also take into account the fluid velocity variation in the wellbore due to multiple pay zones. We present coupled boundary conditions at the interfaces between the wellbore and adjacent formation, the wellbore and pay zone, and the pay zone and adjacent formation. Finally, an alternating direction implicit difference method （ADI） is used to solve the temperature model for the downhole temperature distribution. The comparison of modeled temperature curve with actual temperature log indicates that simulation result is in general quite similar to the actual temperature log. We found that the total production rate, production time, porosity, thickness of pay zones, and geothermal gradient, all have effects on the downhole temperature distribution.

Two-dimensional investigation of characteristic parameters and their gradients for the self-generated electric and magnetic fields of laser-induced zirconium plasma

Two-dimensional diagnosis of laser-induced zirconium(Zr)plasma has been experimentally performed using the time-of-flight method by employing Faraday cups in addition to electric and magnetic probes.The characteristic parameters of laser-induced Zr plasma have been evaluated as a function of different laser irradiances ranging from 4.5 to 11.7 GW cm-2 at different axial positions of 1–4 cm with a fixed radial distance of 2 cm.A well-supporting correlation between the plume parameters and the laser-plasma-produced spontaneous electric and magnetic(E and B)fields was established.The measurements of the characteristic parameters and spontaneously induced fields were observed to have an increasing trend with the increasing laser irradiance.However,when increasing the spatial distance in both the axial and radial directions,the plasma parameters(electron/ion number density,temperature and kinetic energy)did not show either continuously increasing or decreasing trends due to various kinetic and dynamic processes during the spatial evolution of the plume.However,the E and B fields were observed to be always diffusing away from the target.The radial component of electron number densities remained higher than the axial number density component,whereas the axial ion number density at all laser irradiances and axial distances remained higher than the radial ion number density.The higher axial self-generated electric field(SGEF)values than radial SGEF values are correlated with the effective charge-separation mechanism of electrons and ions.The generation of a self-generated magnetic field is observed dominantly in the radial direction at increasing laser irradiance as compared to the axial one due to the deflection of fast-moving electrons and the persistence of two-electron temperature on the radial axis.

On the Thermal Distribution in Oncological Hyperthermia Treatments

The temperature is one of the principal controlling parameters of oncological hyperthermia. However, local heating forms a complicated thermal distribution in space and has developed over time, too. The decisional factors are the heterogeneity of the targeted volume, the electrolyte perfusions controlled by thermal homeostasis, and the spreading of the heat energy with time. A further complication is that the energy absorption sharply changes by depth, so the spatiotemporal development of the temperature distribution requires specialized methods to control. Most of the temperature imaging facilities (thermography, radiometry, electric impedance tomography, etc.) are less precise than the medical practice needs. In contrast, precise point sensing (like thermocouples, thermistors, and fluoroptical methods) is invasive and measures only a discrete point in the robustly changing thermal map. The two most precise thermal imaging methods, computer tomography, and magnetic resonance are expensive and have numerous technical complications. Our objective is to show the complexity of the temperature distribution inside the human body, and offer a relatively simple and cheap method to visualize its spatiotemporal development. A novel emerging technology, the application of ultrasound microbubble contrast agents is a promising method for solving complicated tasks of thermal distribution deep inside the living body. Noteworthy, the temperature distribution does not determine the full hyperthermia process, nonthermal effects make considerable impact, too. Additionally to the difficulties to measure the thermal heterogeneity during hyperthermia in oncology, numerous nonthermal processes, molecular and structural changes are triggered by the incoming electromagnetic energy, which presently has no spatiotemporal visualization technique. Microbubble imaging has a suitable spatiotemporal thermal resolution, and also it is sensitive to nonthermal effects. Its application for characterization of the modulated electrohyperthermia (mEHT) may open a new theranostic facility, using the synergy of the thermal and nonthermal effects of the radiofrequency delivered energy. This complex approach gives facility to follow the mEHT processes, and the proposed microbubble ultrasound imaging has a particularly promising advantage sensing and acting also nonthermally, having potential to characterize the thermally conditioned nonthermal electromagnetic effects in oncologic hyperthermia. The mEHT combined with microbubble ultrasound images could be a robust theranostic method against cancer.