IMPROVING MATERIAL REMOVAL RATE OF BRITTLE CERAMICS THROUGH HONING INCIDENTAL TENSILE STRESSES

The stress intensity factors and stress conditions of machining cracks are analyzed by fracture mechanics on the basis of honing characteristics and of brittle ceramic mechanical behavior.Because the honing incidental tensile stresses effectively decrease the critical grinding stresses and increase the stress intensity factors of machining cracks,the honing process can be carried out easily.The results show that honing can be an efficient machining method for brittle materials.

Experimental research on creep behaviors of sandstone under uniaxial compressive and tensile stresses

The consideration of time dependence is essential for the study of deformation and fracturing processes of rock materials, especially for those subjected to strong compressive and tensile stresses. In this paper, the self-developed direct tension device and creep testing machine RLW-2000M are used to conduct the creep tests on red sandstone under uniaxial compressive and tensile stresses. The short-term and long-term creep behaviors of rocks under compressive and tensile stresses are investigated, as well as the long-term strength of rocks. It is shown that, under low-stress levels, the creep curve of sandstone consists of decay and steady creep stages; while under high-stress levels, it presents the accelerated creep stage and creep fracture presents characteristics of brittle materials. The relationship between tensile stress and time under uniaxial tension is also put forward. Finally, a nonlinear viscoelastoplastic creep model is used to describe the creep behaviors of rocks under uniaxial compressive and tensile stresses.

Film-induced Tensile Stress during CorrosionProcess for α-Ti

The α-Ti foil with protective layer in one side bended to corrosion surface gradually during corrosion process in 0.1 mol/L H2SO4, while the passive film was formed, i.e., a tensile stress was developed in the surface layer of the sample. The extra tensile Stress grew gradually, whose maximum value is =313 MPa (average of 5 samples), which is near or reaches the yield stress. The extra tensile stress would be added to the load Stress during SCC to facilitate the emission and motion of dislocation, so that SCC cracks could nucleate in lower Stress(or lower KI).

EFFECT OF TENSILE STRESS AND RESIDUAL STRESS ON THE SPONTANEOUS STRAY FIELD SIGNALS FROM THE SURFACE OF 0.45%C STEEL

In order to explore the quantitative method of metal magnetic memory testing（MMMT） and clarify the relationship between Hp（y）, the normal component of spontaneous stray field, and applied stress or residual stress, the static tensile tests of 0.45%C steel sheet specimens are carried out on a servo hydraulic MTS810 machine. Hp（y） values are measured during the test process by an EMS-2003 metal magnetic memory diagnostic apparatus and a non-magnetic electric control displacement instrument. Residual stresses of some points on the surface of a specimen are measured by a Stress Tech X-Stress 3000 X-ray diffraction instrument. The results show that the same variation rules of Hp（y） value versus applied tensile stress are presented under the different conditions of load-on and load-off. However, the same rule does not exist between the Hp（y） value and residual stress. The variation of Hp（y） value reflects the history of applied tensile stress.

Tensile Stress Induced Phase Transformations in Zn-Al Alloy

Both furnace cooled and as-cast eutectoid Zn-Al alloys were investigated under external tensile stress at 100℃. It was observed that the external tensile stress caused decomposition of two metastable phases η'T and η'S which derived from both original state of the alloy, and a phase transformation, αf +ε→T' +η， in both furnace cooled and as-cast eutectoid Zn-Al alloys. Also spheroidized structure formed partially during tensile testing. Superplasticity of the alloy has been discussed correlating with the phase transformations and microstructural changes.

Oxidation behavior of Ni-based superalloy GH4738 under tensile stress

Revealing the oxidation behavior of superalloys is crucial for optimizing material properties and extending service life.This study investigated the oxidation behavior of superalloy GH4738 under stress states at 850℃.High-throughput specimens were fabricated to withstand different stresses at the same time.Isothermal oxidation s amples were analyzed using the mass gain method to obtain oxidation kinetic curves.The results show that the external stress below 200 MPa could improve the oxidation resistance of the GH4738.With tensile stress increasing,the oxide layer becomes thinner,denser and more complete,while internal oxidation decreases.The tensile stress alters the structure of the external oxide layer from a two-layer to a threelayer configuration.The Cr_(2)O_(3) oxide layer inhibits the outward diffusion of Ti,leading to Ti enrichment at the oxide-matrix interface and altering the oxidation mechanism of GH4738.

Synergistic Effects of Gamma Irradiation,Tensile Stress and Moisture on the Radiolysis of Silicone Foam

The present work involves the investigation of the synergistic effects of gamma irradiation,tensile stress and absorbed moisture on the radiolysis behaviors of silicone foams by experiments and theoretical simulations.For both the pristine and dehydrated samples,the permanent tensile set increases with the initial tensile strain.Further analysis uncovers that the dehydrated samples exhibit greater permanent tensile sets,lower further elongation and higher Young’s modulus than the counterparts of the pristine samples with the same initial tensile strain and gamma dose,verifying the vital synergistic effects on crosslinking network and aggregation structures caused by moisture and gamma radiation.The synergistic effects unveiled by reactive molecular dynamics at the atomic scale are due to the moisture-induced neutralization and stabilization of the macromolecular radicals.The steric hindrance of moisture located at the interface of silica and polymer chains also conduces to the observed synergistic effects due to the inhibited crosslinking reactions.

Xyloglucan for Generating Tensile Stress to Bend Tree Stem

In response to environmental variation, angiosperm trees bend their stems by forming tension wood, which consists of a cellulose-rich G （gelatinous）-Iayer in the walls of fiber cells and generates abnormal tensile stress in the secondary xylem. We produced transgenic poplar plants overexpressing several endoglycanases to reduce each specific polysaccharide in the cell wall, as the secondary xylem consists of primary and secondary wall layers. When placed horizontally, the basal regions of stems of transgenic poplars overexpressing xyloglucanase alone could not bend upward due to low strain in the tension side of the xylem. In the wild-type plants, xyloglucan was found in the inner surface of G-layers during multiple layering. In situ xyloglucan endotransglucosylase （XET） activity showed that the incorporation of whole xyloglucan, potentially for wall tightening, began at the inner surface layers S1 and S2 and was retained throughout G-layer development, while the incorporation of xyloglucan heptasaccharide （XXXG） for wall loosening occurred in the primary wall of the expanding zone. We propose that the xyloglucan network is reinforced by XET to form a further connection between wall-bound and secreted xyloglucans in order to withstand the tensile stress created within the cellulose G-layer micro fibrils.

High-temperature oxidation behavior of DZ125 Ni-based superalloy under tensile stress

The key in antioxidant capacity of aero-engine hot components is the protective oxide scales.Many factors can affect the performance of oxide scales.The effect of tensile stress on high-temperature oxidation behavior of directionally solidified DZ125 Ni-based superalloy was investigated by thermogravimetric analysis(TGA).Tensile samples were subjected to stress of 100 MPa,and the oxidation behavior was studied at 980℃in air.The surface and cross-sectional morphologies of the oxidized coating were analyzed by scanning electron microscope(SEM).The influence of tensile stress on the oxidation behavior of directionally solidified DZ125 Ni-based superalloy at high temperature was discussed.Results show that an applied tensile stress generally leads to larger Cr/Ni mass ratio in the oxide scales,greater overall chromium depletion values directly under the oxide scales,lower specific weight gain values and thinner oxide scales.These factors are attributed to the formation of fast diffusion paths for Cr atoms to diffuse to the surface under tensile stress,thus causing a reduction in the duration of the less protective transient oxidation period and promoting a faster formation of the protective Cr_(2)O_(3)layer.

Tailoring microstructure and electrical transportation through tensile stress in Bi_(2)Te_(3) thermoelectric fibers

Bismuth telluride(Bi_(2)Te_(3))has attracted much attention in the field of thermoelectrics since it is one kind of commercial room-temperature thermoelectric material.Herein three kinds of Bi_(2)Te_(3) thermoelectric fibers with internal tensile stress are fabricated utilizing an optical fiber template method.The effects of internal stress on the microstructure and the electrical transportation of Bi_(2)Te_(3) thermoelectric fibers are investigated.The Bi_(2)Te_(3) cores in the fibers are highly crystalline and possess a tensile nanosheet structure with preferential orientation as evidenced by X-ray diffraction and Raman studies.Tensile stress can enhance electrical properties of the fibers.And a paper cup generator covered with 20 pieces of optimized fibers provides a μW-level output power.It is inferred that tensile stress tuning can be an effective tool for the material optimization of thermoelectric performance.

Simultaneous imaging and measurement of tensile stress on cornea by using a common-path optical coherence tomography system with an external contact reference

The objective of this study is to demonstrate that tensile stress resulting due to applied force on cornea can be accurately measured by using a time-domain common-path optical coherence tomography （OCT） system with an external contact reference. The unique design of the common-path OCT is utilized to set up an imaging system in which a chicken eye is placed adjacent to a glass plate serving as the external reference plane for the imaging system. As the force is applied to the chicken eye, it presses against the reference glass plate. The modified OCT image obtained is used to calculate the size of contact area, which is then used to derive the tensile stress on the cornea. The drop in signal levels upon contact of reference glass plate with the tissue are extremely sharp because of the sharp decline in reference power levels itself, thus providing us with an accurate measurement of contact area. The experimental results were in good agreement with the numerical predictions. The results of this study might be useful in providing new insights and ideas to improve the precision and safety of currently used ophthalmic surgical techniques. This research outlines a method which could be used to provide high resolution OCT images and a precise feedback of the forces applied to the cornea simultaneously.

Numerical Simulation of Stress Field in Physical Tempering Process of Flat Soda Lime Silica Glass

Based on the analysis of different theory for glass tempering process,the“structural theory”with stress relaxation and structural relaxation effects was selected to investigate the tempering of flat glass quantificationally.The geometrical model with small size and non-homogeneous mesh were considered to build the finite element models according to the characteristics of stress field.The tempering process of flat glass with12 mm thickness was calculated with the verified finite element model.The transient and permanent stress of the central area,edge and corner end of the flat glass are obtained and analyzed.From the calculation results of basic case,the transient tensile stress at the upper surface of the central area,the center point of edge,the edge of edge,the edge of corner were 14.30,18.94,40.76 and 34.75 MPa,respectively.The transient tensile stress at these points were dangerous to promote the glass to break during the tempering.In addition,the point at the diagonal line of symmetry plane in the thickness direction,which is 14 mm from corner,has the maximum permanent tensile stress about 70.01 MPa in the flat glass after tempering.Thus,it is indicated that the corner is the weakest region in the tempered glass.

Analysis of stresses at the center of transversely isotropic Brazilian disk

This article presents the stresses at the center of a Brazilian disk(BD)for transversely isotropic rocks.It is shown that the solution of stresses at the center of an anisotropic disk is a function of the disk radius and the magnitude of applied load,as well as the material orientation with respect to the load axis and two dimensionless ratios with specific physical meanings and limitations.These two dimensionless parameters are the ratios of Young’s modulus and apparent shear modulus,although the ratio of apparent shear modulus will be eliminated if the Saint-Venant assumption is considered.Considerable finite element simulations are carried out to find the stresses at the disk center concerning the material orientation and the two dimensionless parameters.Also,an approximate formula obtained from analytical results,previously proposed in the literature for solving the tensile and compressive stresses at the disk center,is re-written and simplified based on these new definitions.The results of the approximate formula fitted to the analytical results are compared to those obtained from numerical solutions,suggesting a good agreement between the numerical and analytical methods.An approximate equation for the shear stress at the disk center is also formulated based on the numerical results.Finally,the influence of the assumptions for simplification of the proposed formula for the tensile,compressive,and shear stresses at the disk center is discussed,and simple and practical equations are proposed as estimations for the stresses at the center of the BD specimen for low to moderate anisotropic rocks.For highly anisotropic rocks,the reference plots can be used for more accuracy.

Chloride Resistance of Concrete under Complex Stress and Environment

The presence of stress is shown to have a significant impact on chloride ions in concrete. Reinforced concrete is usually durable and cost-effective which has resulted in its widespread use for construction, however, the concrete subjected to environment and load has become increasingly apparently that attacked by aggressive agents such as chloride ion. In this study, the coupling influences are stress effects and environmental problems on the coastline concrete durability have been investigated. A series of cyclic of a wet-dry cycle and submersion tests were performed onto the stressed concrete to obtain an understanding of the physical mechanisms causing the accumulation of chlorides in the interior pores of concrete under different stress types and exposure environments, based on the same duration. Specimens were prepared and subjected to NaCl solution in a wet-dry cycle and submersion, the chloride in the tension zone is gradual with increasing the stress level, as well as the chloride ion in the wet-dry cycle, is increasing the number of cycles. The apparent diffusion coefficient of each specimen was calculated respectively, the profile of concentration at a different section of tension and compression zones were presented in influence factors of the number of cycles, the length of drying phase, and periodic wetting cycles with sodium solution was discussed. After employed Fick’s second law, the results suggested Da in a wet-dry cycle is much higher than the Da in submersion zones.

Stress and strain analysis on the anastomosis site sutured with either epineurial or perineurial sutures after simulation of sciatic nerve injury

The magnitude of tensile stress and tensile strain at an anastomosis site under physiological stress is an important factor for the success of anastomosis following suturing in peripheral nerve injury treatment. Sciatic nerves from fresh adult cadavers were used to create models of sciatic nerve injury. The denervated specimens underwent epineurial and perineurial suturing. The elastic modulus （40.96 ＋ 2.59 MPa） and Poisson ratio （0.37 ＋ 0.02） of the normal sciatic nerve were measured by strain electrical measurement. A resistance strain gauge was pasted on the front, back left, and right of the edge of the anastomosis site after suturing. Strain electrical measurement results showed that the stress and strain values of the sciatic nerve following perineurial suturing were lower than those following epineurial suturing. Scanning electron microscopy revealed that the sciatic nerve fibers were disordered following epineurial compared with perineurial suturing. These results indicate that the effect of perineurial suturing in sciatic nerve injury repair is better than that of epineurial suturing.

TENSILE PROPERTIES AND CREEP RESISTANCE OF AZ91 ALLOY CONTAINING ANTIMONY

Small amount of antimony addition to the Mg-9Al-0.8Zn-0.2Mn(AZ91) alloy results in the obvious increase of tensile strength at both ambient and elevated temperatures. The creep resistance at the temperatures up to 200°C is also improved significantly by antimony addition. Microstructural observations revealed that the addition of antimony modifies morphology of the β(Mg17Al12) phase and causes the formation of some rod-shaped precipitates Mg3Sb2 at grain boundaries. These precipitates have high thermal stability and play an important role for strengthening grain boundaries at elevated temperatures.

Experimental study on complete stress-deformation curves of larger-size concrete specimens subjected to uniaxial tension

In order to provide parameters for numerical analyses of the huge Three-Gorge concrete dam (2309 m long by 175 m height), complete tensile stress-deformation curves for large-size plain concrete specimens were measured and studied by per-forming uniaxial tensile tests on large-size unnotched specimens (250 mm×250 mm×1400 mm). The specimens were prepared with the three-graded-aggregate materials provided by the client of the Three-Gorge project. To prevent a failure occurring near the ends of the unnotched specimens, both the ends of each specimen (450 mm in length) were cast using a higher-strength concrete than the middle part (i.e., active part). Tensile tests were completed on a specially-designed tensile testing machine, which can be easily re-assembled to accommodate different-size specimens. To make the specimens fail stably, a cyclic loading scheme was adopted after the peak strength was reached. Four of five tests in this study were successful, and four complete tensile stress-deformation curves were obtained. It was found that the post-peak curve of the large-size specimens used in this study is more gradual than those for the small-size specimens reported in the literature.

Experimental investigation of electrode cycle performance and electrochemical kinetic performance under stress loading

Lithium-ion batteries suffer from mechano–electrochemical coupling problems that directly determine the battery life. In this paper, we investigate the electrode electrochemical performance under stress conditions, where seven tensile/compressive stresses are designed and loaded on electrodes, thereby decoupling mechanics and electrochemistry through incremental stress loads. Four types of multi-group electrochemical tests under tensile/compressive stress loading and normal package loading are performed to quantitatively characterize the effects of tensile stress and compressive stress on cycle performance and the kinetic performance of a silicon composite electrode. Experiments show that a tensile stress improves the electrochemical performance of a silicon composite electrode, exhibiting increased specific capacity and capacity retention rate, reduced energy dissipation rate and impedances, enhanced reactivity, accelerated ion/electron migration and diffusion, and reduced polarization. Contrarily, a compressive stress has the opposite effect, inhibiting the electrochemical performance. The stress effect is nonlinear, and a more obvious suppression via compressive stress is observed than an enhancement via tensile stress. For example, a tensile stress of 675 k Pa increases diffusion coefficient by 32.5%, while a compressive stress reduces it by 35%. Based on the experimental results, the stress regulation mechanism is analyzed. Tensile stress loads increase the pores of the electrode material microstructure, providing more deformation spaces and ion/electron transport channels. This relieves contact compressive stress, strengthens diffusion/reaction, and reduces the degree of damage and energy dissipation. Thus, the essence of stress enhancement is that it improves and optimizes diffusion, reaction and stress in the microstructure of electrode material as well as their interactions via physical morphology.

Moiré method analysis for tensile strain field of 2024 aluminum alloy welded joint

Using experimental mechanics method of moiré analysis, strain field distributions of 2024 aluminum alloy welded joints under different conditions were investigated. The results show that moiré stripes of welded joint without trailing peening just before fracture are not only few and scattered but also uneven, and the stress mainly concentrates on the poor position welded toes during the tensioning process with the relatively poor mechanical properties of welded joints; When the method of welding with trailing peening is adopted, moiré stripes of welded joint just before fracture are relatively thick and even due to the strengthening welded toes during the welding process, and fracture position transfers from the welded toes to weld, at the same time the mechanical properties of welded joints are improved greatly than conventional welding which can show that the technology of trailing peening is effective to strengthen welded joints of aluminum alloy with high strength.

Responses of osteoblasts under varied tensile stress types induced by stretching basement materials

Osteoblasts are mechanosensitive cells.Tensile stress with different conditions,including loading time,frequency,magnitude,etc.would cause varied responses in osteoblasts.However,it was not clarified that the effect of the loading types on the osteoblasts.In this study,we focused on the effect of varied tensile stress types on osteoblasts,including isotropic stretch,biaxial stretch,and uniaxial stretch with the negative ratio of transverse strain to axial strain(NR)-1,0,and 0.2 respectively.Cell proliferation was determined to be most efficient when stimulated by 6%strain at a frequency of 1 Hz and a negative value of 0 for 1 h/day.The varied strain resulted in a thickening of the F-actin cytoskeleton and a thinning of the nucleus.Nuclear flattening caused Yes-associated protein(YAP)to be transported to the nucleus.It was suggested that the influence of loading types on the mechanobiology responses must be noticed.The mechanism of cell mechanical sensitivity under varied loading types was explored,which would provide good sugges-tions for designing microstructures to control deformation patterns in bone tissue engineering.