Study on mechanical properties of composite materials by in-situ tensile test

The mechanical properties of the SiC fiber-reinforced Mg-Al metal matrix composite materials have been studied on internal microstructure by (scanning electron microscopy) SEM in-situ tensile test. The emergence and propagation of the crack, and the fracture behavior in materials have been observed and studied. It is found that in the case of the tensile test, the crack emerged in SiC fiber initially. In the case of the strong cohesion of the fiber-metal interface, the crack propagated in the fiber, meanwhile the fibers in the neighborhood of the cracked fiber began to crack and the Mg-Al metal deformed plastically, and at last the material fractured. Otherwise the toughness of the materials grows in the case of the lower cohesion of the fiber-metal matrix interface.

Acoustic emission activity in directly tensile test on marble specimens and its tensile damage constitutive model

For understanding acoustic emission （AE） activity and accumulation of micro-damage inside rock under pure tensile state, the AE signals has been monitored on the test of directly tension on two kinds of marble specimens. A tensile constitutive model was proposed with the damage factor calculated by AE energy rate. The tensile strength of marble was discrete obviously and was sensitive to the inside microdefects and grain composition. With increasing of loading, the tensile stress-strain curve obviously showed nonlinear with the tensile tangent modulus decreasing. In repeated loading cycle, the tensile elastic modulus was less than that in the previous loading cycle because of the generation of micro damage during the prior loading. It means the linear weakening occurring in the specimens. The AE activity was corresponding with occurrence of nonlinear deformation. In the initial loading stage which only elastic deformation happened on the specimens, there were few AE events occurred; while when the nonlinear deformation happened with increasing of loading, lots of AE events were generated. The quantity and energy of AE events were proportionally related to the variation of tensile tangent modulus. The Kaiser effect of AE activity could be clearly observed in tensile cycle loading. Based on the theory of damage mechanics, the damage factor was defined by AE energy rate and the tensile damage constitutive model was proposed which only needed two property constants. The theoretical stress-strain curve was well fitted with the curve plotted with tested datum and the two property constants were easily gotten by the laboratory testing.

Characterization of microstructure and strain response in Ti-6Al-4V plasma welding deposited material by combined EBSD and in-situ tensile test

Additive layer manufacturing （ALM） of aerospace grade titanium components shows great promise in supplying a cost-effective alternative to the conventional production routes. Complex microstructures comprised of columnar remnants of directionally solidifiedβ-grains, with interior inhabited by colonies of finerα-plate structures, were found in samples produced by layered plasma welding of Ti-6Al-4V alloy. The application of in-situ tensile tests combined with rapid offline electron backscatter diffraction （EBSD） analysis provides a powerful tool for understanding and drawing qualitative correlations between microstructural features and deformation characteristics. Non-uniform deformation occurs due to a strong variation in strain response between colonies and across columnar grain boundaries. Prismatic and basal slip systems are active, with the prismatic systems contributing to the most severe deformation through coarse and widely spaced slip lines. Certain colonies behave as microstructural units, with easy slip transmission across the entire colony. Other regions exhibit significant deformation mismatch, with local build-up of strain gradients and stress concentration. The segmentation occurs due to the growth morphology and variant constraints imposed by the columnar solidification structures through orientation relationships, interface alignment and preferred growth directions. Tensile tests perpendicular to columnar structures reveal deformation localization at columnar grain boundaries. In this work connections are made between the theoretical macro- and microstructural growth mechanisms and the observed microstructure of the Ti-6Al-4V alloy, which in turn is linked to observations during in-situ tensile tests.

Microstructural Changes of Graphene/PLA/PBC Nanofibers by Electrospinning during Tensile Tests

This study focuses on the nanostructure and nanostructural changes of novel graphene/poly（lactic acid） （PLA）/ poly（butylene carbonate） （PBC） nanofibers via electrospinning, which are characterized by differential scanning calorimetry （DSC）, scanning electron microscopy （SEM）, tensile test and in situ small angle x-ray scattering. DSC indicates that the endothermic peak at 295℃ of pure PLA/PBC nanofibers shifted from 317℃ to lower 290℃ with the increasing graphene content. SEM observations reveal a fine dispersion of graphene in the nanofiber matrices. The graphene/PLA/PBC nanofiSers exhibit good improvements in mechanical property. The tensile strength of nanofibers increases with the addition of 0.01 g graphene but reduces with further addition of 0.04g graphene. The scattering intensities increase dramatically when the strain levels are higher than the yield point due to the nucleation and growth of nanovoids or crystals. However, the increasing content of graphene in the PLA/PBC matrix provokes a strong restriction to the deformation-induced crystals.

TENSILE TEST AND PHYSICAL MODEL OF NiTi SHAPE MEMORY ALLOY

The tensile stress-strain curves of NiTi wires are obtained by tensile experiments under different heat treatments. A phenomenological physical model based on hysteresis element method is developed to describe the experimentally determined stress-strain curves of shape memory alloy (SMA) wires. Numerical simulations are made. Simulation results show that：(1) a series of unusual changes on physical and mechanical properties of SMA wires occur when martensitic, especially R (rhombohedral) phase transformation emerge. The stress-strain relation of SMA wires is highly non-linear; (2) there are no notable yielding phenomena before NiTi wires are broken; (3) numerical results obtained by the physical model are in good agreement with experimental data.

Analysis on the deformation and fracture behavior of carbon steel by in situ tensile test

The deformation and fracture behaviors of low-carbon steel, medium-carbon steel, and high-carbon steel were studied on internal microstructure using the scanning electron microscopy in situ tensile test. The microstructure mechanism of their deformation and fracture behavior was analyzed. The results show that the deformation and fracture behavior of low-carbon steel depends on the grain size of ferrite, the deformation and fracture behavior of medium-carbon steel depends on the size of ferrite grain and pearlite lump, and the deformation and fracture behavior of high-carbon steel depends on the size of pearlite lump and the pearlitic interlamellar spacing.

A METHOD TO QUANTIFY CRAZING DEFORMATION BY TENSILE TESTS FOR POLYSTYRENE/POLYOLEFIN ELASTOMER IMMISCIBLE BLENDS

A method to quantify crazing deformations by tensile tests for polystyrene （PS） and polyolefin elastomer （POE） blends was investigated. The toughness of PS/POE blends, reflected by the Charpy impact strength, increased with the content of POE. SEM micrographs showed the poor compatibility between PS and POE. In simple tensile tests, it is very easy to achieve the ratio of crazing deformation, i.e. K by measuring the size changes of samples. The K values decreased with increasing the content of POE, and the deformations of PS/POE blends were dominated by crazing. The plots of the change of volume （△V） against longitudinal variation （△I） showed a linear relationship, and the slope of lines decreased with the content of POE. Measuring samples at the tensile velocities of 5 mm/min, 50 mm/min, and 500 mm/min respectively, the K values kept unchanged for each PS/POE blends.

Study of Deformation Coating for Sheets by Using Tensile Test

This article focuses on the study of the defined values of tensile strain and the effect of low temperature plasma adhesion selected coatings on steel samples using a tensile testing flat test bars. Samples were made by machining and welding technologies. The flat test bars were tested by pulling on a test rig UPC 1200. Part of the samples was treated on the surface prior to coating by a tensile test, second base coat and with a final coat continuous multi plasma system. The selected test samples were determined from the tensile test of the material characteristics apparent from the tensile diagrams. The examined samples were fitted top and base coat. Another group was the KTL basis. The presented graphs show the dependence of the strength on elongation of a sample according to DIN EN ISO 6892-2. The samples were then examined under a stereo microscope SCHUT brand, type SSM-E in the laboratory to conduct coating on a steel sheet at the moment of total violation sectional samples. The base layer, in which the temperature ranges from 160°C - 180°C, was applied by electrophoresis method.

In-situ X-ray computed tomography tensile tests and analysis of damage mechanism and mechanical properties in laser powder b e d fused Invar 36 alloy

Laser powder bed fusion(LPBF)is a potential additive manufacturing process to manufacture Invar 36 alloy components with complicated geometry.Whereas it inevitably introduces specific microstructures and pore defects,which will further influence the mechanical properties.Hence,aiming at exploring the LPBF process-related microstructures and pore defects,and especially their influences on the damage mechanism and mechanical properties,Invar 36 alloy was manufactured by LPBF under designed different laser scanning speeds.The microstructure observations reveal that higher scanning speeds lead to equiaxed and short columnar grains with higher dislocation density,while lower scanning speeds result in elongated columnar grains with lower dislocation density.The pore defects analyzed by X-ray computed tomography(XCT)suggest that the high laser scanning speed gives rise to numerous lamellar and large lack-of-fusion(LOF)pores,and the excessively low laser scanning speed produces relatively small keyhole pores with high sphericity.Moreover,the insitu XCT tensile tests were originally performed to evaluate the damage evolution and failure mechanism.Specifically,high laser scanning speed causes brittle fracture due to the rapid growth and coalescence of initial lamellar LOF pores along the scan-ning direction.Low laser scanning speed induces ductile fracture originating from unstable depressions in the surfaces,while metallurgical and keyhole pores have little impact on damage evolution.Eventually,the process-structure-property correlation is established.The presence of high volume fraction of lamel-lar LOF pores,resulting from high scanning speed,leads to inferior yield strength and ductility.Besides,specimens without LOF pores exhibit larger grain sizes and lower dislocation density at decreased scanning speeds,slightly reducing yield strength while slightly enhancing ductility.This understanding lays the foundation for widespread applications of LPBF-processed Invar 36 alloy.

Forming Limit Stress Diagram Prediction of Aluminum Alloy 5052 Based on GTN Model Parameters Determined by In Situ Tensile Test

The conventional forming limit diagram （FLD） is described as a plot of major strain versus minor strain. However, FLD is dependent on forming history and strain path. In the present study, a forming limit stress-based diagram （FLSD） has been adopted to predict the fracture limit of aluminum alloy （AA） 5052-O1 sheet. Nakazima test is simulated by plastic constitutive formula derived from the modified Gurson-Tvergaard-Needleman （GTN） model. An in situ tensile test with scanning electron microscope （SEM） is proposed to determine the parameters in GTN model. The damage evolution is observed and recorded, and the parameters of GTN model are identified through counting void fraction at three damage stages of AA5052-O 1. According to the experimental results, the original void volume fraction, the volume fraction of potential nucleated voids, the critical void volume fraction, the void volume fraction at the final failure of material are assigned as 0.002 918, 0.024 9, 0.030 103, 0.048 54, respectively. The stress and strain are obtained at the last loading step before crack. FLSD and FLD of AA5052-O 1 are plotted. Compared with the experimental Nakazima test and uniaxial tensile test, the predicted results show a good agreement. The parameters determined by in situ tensile test can be applied to the research of the forming limit for ductile metals.

Influence of uniaxial tensile pre-strain on forming limit curve by using biaxial tensile test

This paper focused on the effect of pre-strain on forming limit curves(FLC)of 5754-O aluminum alloy sheet through utilizing biaxial tensile approach.Based on Swift model and Yld2000-2 d yield criterion,the dimensions of cruciform specimen was optimized through applying finite element method for increasing the strain at specimen center.After that,with the recommended specimen size,the cruciform specimen was tested under various stroke ratios to experimentally characterize the limit strains under different pre-strain levels.Subsequently,the biaxial tensile tests were simulated by Abaqus to obtain the limit strains and validate the material models.It can be observed in both experiments and simulations that the pre-strained uniaxial tension followed by plane tension or equi-biaxial tension can improve the formability of sheet metals.Besides,the strain path change affects the trend of first derivative of strain rate difference between neighboring points with respect to time.An early increase occurred and then fell back to the stable value,the steady evolution continued until to a new increase reaching the critical value.The M–K prediction approach was simulated to verify the influence of pre-strain on FLC.It can be found that the early increase peaks of the major strain incremental ratio rose with the amplitude of pre-strain.Finally,the phenomenon of pseudolocalization caused by the strain path change was explained through evolution of stress state inside the groove.

Probing into the Yield Plateau Phenomenon in Commercially Pure Titanium During Tensile Tests

To explain the intrinsic mechanism of the yield plateau phenomenon in commercially pure titanium,the tensile behaviors of commercially pure titanium specimens after 91.6%cryorolling and subsequent annealing at 280℃,335℃,450℃and 600℃have been studied.The results show that the yield plateau phenomenon is a result of dislocation behaviors controlled by grain size and thus only exists within a given range of mean grain size.αgrain boundaries are the main dislocation multiplication sources of commercially pure titanium.Fine-grained microstructure could offer numerous dislocation multiplication locations during deformation.Once the applied stress is above the yielding strength,dislocations multiply rapidly and the mobile dislocation density is high.To retrieve the imposed strain rate,the mean dislocation velocity is bound to be low.Therefore,it takes time for them to interact with each other.As a result,the movement of dislocations is hardly blocked and the deformation could continue at a nearly constant applied stress.Consequently,the so-called yield plateau behavior presents in the tensile curves.The disappearance of yield plateau phenomenon in coarse-grained and ultrafi ne-grained microstructures is attributed to the quick realization of the mutual interactions among dislocations at the initial stage of tensile test.

Exploring an eco-friendly approach to improve soil tensile behavior and cracking resistance

Soil tensile strength is a critical parameter governing the initiation and propagation of tensile cracking.This study proposes an eco-friendly approach to improve the tensile behavior and crack resistance of clayey soils.To validate the feasibility and efficacy of the proposed approach,direct tensile tests were employed to determine the tensile strength of the compacted soil with different W-OH treatment concentrations and water contents.Desiccation tests were also performed to evaluate the effectiveness of W-OH treatment in enhancing soil tensile cracking resistance.During this period,the effects of W-OH treatment concentration and water content on tensile properties,soil suction and microstructure were investigated.The tensile tests reveal that W-OH treatment has a significant impact on the tensile strength and failure mode of the soil,which not only effectively enhances the tensile strength and failure displacement,but also changes the brittle failure behavior into a more ductile quasi-brittle failure behavior.The suction measurements and mercury intrusion porosimetry(MIP)tests show that W-OH treatment can slightly reduce soil suction by affecting skeleton structure and increasing macropores.Combined with the microstructural analysis,it becomes evident that the significant improvement in soil tensile behavior through W-OH treatment is mainly attributed to the W-OH gel's ability to provide additional binding force for bridging and encapsulating the soil particles.Moreover,desiccation tests demonstrate that W-OH treatment can significantly reduce or even inhibit the formation of soil tensile cracking.With the increase of W-OH treatment concentration,the surface crack ratio and total crack length are significantly reduced.This study enhances a fundamental understanding of eco-polymer impacts on soil mechanical properties and provides valuable insight into their potential application for improving soil crack resistance.

Tensile strength and failure behavior of rock-mortar interfaces: Direct and indirect measurements

The tensile strength at the rock-concrete interface is one of the crucial factors controlling the failure mechanisms of structures,such as concrete gravity dams.Despite the critical importance of the failure mechanism and tensile strength of rock-concrete interfaces,understanding of these factors remains very limited.This study investigated the tensile strength and fracturing processes at rock-mortar interfaces subjected to direct and indirect tensile loadings.Digital image correlation(DIC)and acoustic emission(AE)techniques were used to monitor the failure mechanisms of specimens subjected to direct tension and indirect loading(Brazilian tests).The results indicated that the direct tensile strength of the rock-mortar specimens was lower than their indirect tensile strength,with a direct/indirect tensile strength ratio of 65%.DIC strain field data and moment tensor inversions(MTI)of AE events indicated that a significant number of shear microcracks occurred in the specimens subjected to the Brazilian test.The presence of these shear microcracks,which require more energy to break,resulted in a higher tensile strength during the Brazilian tests.In contrast,microcracks were predominantly tensile in specimens subjected to direct tension,leading to a lower tensile strength.Spatiotemporal monitoring of the cracking processes in the rock-mortar interfaces revealed that they show AE precursors before failure under the Brazilian test,whereas they show a minimal number of AE events before failure under direct tension.Due to different microcracking mechanisms,specimens tested under Brazilian tests showed lower roughness with flatter fracture surfaces than those tested under direct tension with jagged and rough fracture surfaces.The results of this study shed light on better understanding the micromechanics of damage in the rock-concrete interfaces for a safer design of engineering structures.

TENSILE TESTING OF C/C COMPOSITES AT HIGH TEMPERATURES

The tensile properties of three different carbonfiberreinforced carbon composites (C/C), mat C/C, 2D laminate and 4D C/C, were investigated under the combined influence of temperature and loading rate. From the experiments the following could be concluded: loading rate between 10-1-10 mm/min was valid; the fracture stress of the three kinds of C/C composites increased with increasing temperature in the range from room temperature to 1900, and the initial modulus of 2D laminate C/C composites increased with the increase of temperature up to 2000.

The Efect of Si Impurity at the Al Σ5 Grain Boundary:a First Principle Computational Tensile Test Study

First principle computational tensile tests （FPCTT） are performed to the Al ∑5 grain boundaries （GBs） with and without substitution or interstitial Si impurity. The obtained stress-strain relationships and atomic configurations demonstrate that the Al ∑5 GBs with and without substitutional or interstitial Si impurity show different fracture modes. The mechanisms of the different fracture modes are analyzed based on the charge density and the density of states. The results show that the charge redistributions of the atoms in the vicinity of GBs and the covalent interactions between Si and its neighboring Al atoms determine the fracture modes.

Effects of ultrasonic vibration on plastic deformation of AZ31 during the tensile process

An investigation on the plastic behavior of AZ31 magnesium alloy under ultrasonic vibration（with a frequency of 15 kHz and a maximum output of 2 kW） during the process of tension at room temperature was conducted to reveal the volume effect of the vibrated plastic deformation of AZ31.The characteristics of mechanical properties and microstructures of AZ31 under routine and vibrated tensile processes with different amplitudes were compared.It is found that ultrasonic vibration has a remarkable influence on the plastic behavior of AZ31 which can be summarized into two opposite aspects：the softening effect which reduces the flow resistance and improves the plasticity,and the hardening effect which decreases the formability.When a lower amplitude or vibration energy is applied to the tensile sample,the softening effect dominates,leading to a decrease of AZ31 deformation resistance with an increase of formability.Under the application of a high-vibrating amplitude,the hardening effect dominates,resulting in the decline of plasticity and brittle fracture of the samples.

Effects of ultrasonic vibration on performance and microstructure of AZ31 magnesium alloy under tensile deformation

Ultrasonic vibration can reduce the forming force, decrease the friction in the metal forming process and improve the surface quality of the workpiece effectively. Tensile tests of AZ31 magnesium alloy were carried out. The stress–strain relationship, fracture modes of tensile specimens, microstructure and microhardness under different vibration conditions were analyzed, in order to study the effects of the ultrasonic vibration on microstructure and performance of AZ31 magnesium alloy under tensile deformation. The results showed that the different reductions of the true stress appeared under various ultrasonic vibration conditions, and the maximum decreasing range was 4.76%. The maximum microhardness difference among the 3 nodes selected along the specimen was HV 10.9. The fracture modes, plasticity and microstructure of AZ31 magnesium alloy also were affected by amplitude and action time of the ultrasonic vibration. The softening effect and the hardening effect occurred simultaneously when the ultrasonic vibration was applied. When the ultrasonic amplitude was 4.6 μm with short action time, the plastic deformation was dominated by twins and the softening effect was dominant. However, the twinning could be inhibited and the hardening effect became dominant in the case of high ultrasonic energy.

Variation of the mechanical properties of tungsten heavy alloys tested at different temperatures

The high-temperature mechanical properties of 95W-3.5Ni-1.5Fe and 95W-4.5Ni-0.5Co alloys were investigated in the temperature range of room temperature to1100℃. The yield strength and tensile strengths declined gradually, and the ductility of both alloys increased as the testing temperature was increased to 300℃. All the three properties reached a plateau at temperatures between 300 and 500℃ in the case of 95W-3.5Ni-l.5Fe and at temperatures between 350 and 700℃ in the case of 95W-4.5Ni-0.5Co. Thereafter, the ductility as well as yield and tensile strengths decreased considerably.

A multifunctional rock testing system for rock failure analysis under different stress states: Development and application

The stress state in a rock mass is complex. Stress redistribution around underground excavation may lead to various failure modes, including compressive-shear, tensile-shear, and tensile failures. The ability to perform laboratory tests with these complex stress states is significant for establishing new strength criteria. The present paper introduces a new rock testing system with “tensile-compressive-shear”loading functions. The device includes bi-directional and double-range hydraulic cylinders, auxiliary loading equipment, and roller rows that can perform direct compressive-shear tests, direct tensile tests,and direct tensile-shear tests. The testing system provides maximum vertical and lateral loading forces of2000 k N and allows testing cubical rock specimens with dimensions of 0.5 m × 0.5 m × 0.5 m. The performance of the testing machine was evaluated by testing a rock-like material based on cement mortar under compressive-shear, tensile, and tensile-shear stress states. The failure process and deformation characteristics were monitored during loading using acoustic emission(AE) transient recorder,piezoelectric AE sensors, a high-speed camera, and a thermal infrared camera. The failure mechanism was investigated by analyzing AE counts, AE amplitude, strain, and temperature changes on the rock specimen surface. The test results confirmed that the testing system could successfully simulate the abovementioned stress path. The AE counts and amplitude responses were influenced by different failure modes. The temperature response during the compressive-shear test indicated the development of a high-temperature band on the rock specimen surface. In contrast, a negligible temperature change was observed during the tensile and tensile-shear tests. The newly developed multifunctional rock testing system allows laboratory tests under various failure modes. The monitoring results of multiple variables during rock failure tests provide valuable information on failure characteristics.