Combined effects of ultrasonic vibration and FeCoNiCrCu coating on interfacial microstructure and mechanical properties of Al/Mg bimetal by compound casting

In this work,a new treatment method combining ultrasonic vibration with FeCoNiCrCu high entropy alloy(HEA)coating was used to prepared Al/Mg bimetal through the lost foam compound casting.The effects of composite treatment involving ultrasonic vibration and HEA coating on interfacial microstructure and mechanical properties of Al/Mg bimetal were studied.Results demonstrate that the interface thickness of the Al/Mg bimetal with composite treatment significantly decreases to only 26.99%of the thickness observed in the untreated Al/Mg bimetal.The HEA coating hinders the diffusion between Al and Mg,resulting the significant reduction in Al/Mg intermetallic compounds in the interface.The Al/Mg bimetal interface with composite treatment is composed of Al_(3)Mg_(2)and Mg_(2)Si/AlxFeCoNiCrCu+FeCoNiCrCu/δ-Mg+Al_(12)Mg_(17)eutectic structures.The interface resulting from the composite treatment has a lower hardness than that without treatment.The acoustic cavitation and acoustic streaming effects generated by ultrasonic vibration promote the diffusion of Al elements within the HEA coating,resulting in a significant improvement in the metallurgical bonding quality on the Mg side.The fracture position shifts from the Mg side of the Al/Mg bimetal only with HEA coating to the Al side with composite treatment.The shear strength of the Al/Mg bimetal increases from 32.16 MPa without treatment to 63.44 MPa with ultrasonic vibration and HEA coating,increasing by 97.26%.

Detection of internal crack growth in polyethylene pipe using guided wave ultrasonic testing

Despite the success of guided wave ultrasonic inspection for internal defect detection in steel pipes,its application on polyethylene(PE)pipe remains relatively unexplored.The growth of internal cracks in PE pipe severely affects its pressure-holding capacity,hence the early detection of internal cracks is crucial for effective pipeline maintenance strategies.This study extends the scope of guided wave-based ultrasonic testing to detect the growth of internal cracks in a natural gas distribution PE pipe.Laboratory experiments and a finite element model were planned to study the wave-crack interaction at different stages of axially oriented internal crack growth with a piezoceramic transducer-based setup arranged in a pitch-catch configuration.Mode dispersion analysis supplemented with preliminary experiments was performed to isolate the optimal inspection frequency,leading to the selection of the T(0,1)mode at 50-kHz for the investigation.A transmission index based on the energy of the T(0,1)mode was developed to trace the extent of simulated crack growth.The findings revealed an inverse linear correlation between the transmission index and the crack depth for crack growth beyond 20%crack depth.

An experimental study exploring the influencing factors for ultrasonic-assisted extraction of flavonoid compounds from leaves of Amorpha fruticosa L.

In this paper,the ultrasonic-assisted extraction process of flavonoid compounds from leaves of Amorpha fruticosa is optimized.In single factor experiments,solid/liquid ratios,ultrasonic power,ethanol concentrations and extraction cycles were experimental factors.Box–Behnken central composite design and RSM analyzed the effects of the four factors on the yield of total flavonoids.The optimal extraction parameters were solid/liquid ratio 1:50 g/mL,ultrasonic power 316 W,ethanol concentration 50%,4 extraction cycles.In the optimized condition,the estimated value of the regression model was 66.6456 mg/g while the measured value was 66.4329 mg/g.

Progress on the ultrasonic testing and laser thermography techniques for NDT of tokamak plasma-facing components

During manufacturing and operation, different kinds of defects, e.g., delamination or surface cracks, may be generated in the plasma-facing components (PFCs) of a Tokamak device. To ensure the safety of the PFCs, various kinds of nondestructive testing (NDT) techniques are needed for different defect and failure mode. This paper gives a review of the recently developed ultrasonic testing (UT) and laser thermography methods for inspection of the delamination and surface cracks in PFCs. For monoblock W/Cu PFCs of divertor, the bonding quality at both W-Cu and Cu- CuCrZr interfaces was qualified by using UT with a focus probe during manufacturing. A noncontact, coupling-free and flexible ultrasonic scanning testing system with use of an electromagnetic acoustic transducer and a robotic inspection manipulator was introduced then for the in-vessel inspection of delamination defect in first wall (FW). A laser infrared thermography testing method is highlighted for the on-line inspection of delamination defect in FW through the vacuum vessel window of the Tokamak reactor. Finally, a new laser spot thermography method using laser spot array source was described for the online inspection of the surface cracks in FW.

Experimental Study on the Ultrasonic Testing including Porosity of Rock Damage Characteristics

Cement mortar specimens are used to simulate the fracture of rock material under uniaxial compression test, using the ultrasonic instrument measurement test process, the waveform and wave velocity results along with the change of specimen fracture extension are obtained. Experimental results show that at 0 MPa, there are micro-defects in the specimen, leading to the irregular change of the waveform of the measuring points 4# and 5#;At 1 - 4 MPa, there is no crack on the surface of the specimen, the waveform of ultrasonic wave is stable, and the velocity of each point increases with the increase of the strain, but the measuring point increases the wave velocity when the load is applied;When the specimen surface cracks, expect the waveform of measuring point 4# and 5# change in irregularities, the measuring point 2# waveform also changes irregularly and measuring point of the wave velocity has decreased;At the crack propagation stage, ultrasonic wave also changes irregularly along with the expansion of crack, wave velocity with the increase of the strain is also obvious downward trend;When the crack penetrates the whole specimen, the waveform of each measuring point changes abnormally, the continuity is bad, the waveform is irregular and the measured wave velocity is low.

Feasibility of differentiating defect signals of ultrasonic testing for laser weld based on independent component analysis theory

Separating noise from observed signals was studied.When the small defect in the T-shape laser welding joint was inspected by ultrasonic testing system adopting independent component analysis(ICA) theory to process the signals.The principle of automatic ultrasonic testing signals processing and negentropy law of ICA were introduced.The experimental data were processed using relative analysis tools and results showed that the ICA could separate defects signals from noise effectively in laboratory.

The Testing Strength Curves of Lightweight Aggregate Concrete by Rebound Method and Ultrasonic-rebound Combined Method

The strength curves of lightweight aggregate concrete （LWAC） were tested based on detecting LWAC with density of 1 400-1 900 kg/m3 and LWAC with strength grade of LC15-LC50 by rebound method and ultrasonic-rebound combined method.The results show that the common measured strength curves tested by above two methods can not satisfy the required accuracy of LWAC strength test.In addition,specified compressive strength curves of testing LWAC by rebound method and ultrasonic-rebound combined method are obtained,respectively.

Ultrasonic Testing Combined with Pattern Recognition for the Detection of Kissing Bonds

Kissing bonds are defects in the adhesive bonds with intimate contact of touching surface but considerably lowered shear strength. Their detection specifically in the aerospace area is so not satisfactory. Usually, kissing bonds are inconspicuous in ultrasonic C-scans. However, the determination of attributes in the time domain and the frequency domain of an ultrasound signal provides the opportunity to derive a pattern for bonded area. Deviations from the pattern found in inconspicuous bonding areas indicate kissing bonds. The survey described here deals with the manufacturing of adhesively joint samples that purposefully include kissing bonds, as well as potential solutions for detecting them through ultrasonic testing combined with pattern recognition. The properties of the epoxy-based adhesive were varied by changing the mixing ratios between resin and hardener. Samples with a mixing ratio far apart from the manufacturer’s recommendation with an inconspicuous appearance in a C-scan, but low shear strength values were taken for further evaluation. After a definition and learning phase, a 100 percent hit rate to separate good bondings from kissing bonds could be derived in a blind test. The discriminating feature found is due to the frequency shift between good and kissing bonds as well as the relative amplitude of the second peak.

Effect of ultrasonic vibration on Fe-containing intermetallic compounds of hypereutectic Al-Si alloys with high Fe content

The Fe-containing intermetallic compounds with high melting point in hypereutectic Al-Si alloys can improve the heat resistance and wear resistance at elevated temperatures. However, the long needle-like Fe-containing compounds in the alloys produced by conventional casting process are detrimental to the strength of matrix. The effect of ultrasonic vibration （USV） on the morphology change of Fe-containing intermetallic compounds in the hypereutectic Al-17Si-xFe （x=2, 3, 4, 5） alloys was systematically studied. The results show that, the Fe-containing intermetallic compounds are mainly composed of long needle-like β-Al5FeSi phase with a small amount of plate-like δ-Al4FeSi2 phase in Al-17Si-2Fe alloy produced by conventional casting process. With the increase of Fe content from 2% to 5% in the alloys, the amount of plate-like or coarse needle-like δ-Al4FeSi2 phase increases while the amount of long needle-like β-Al5FeSi phases decreases. In Al-17Si-5Fe alloy, the Fe-containing intermetallic compounds exist mainly as coarse needle-like δ-Al4FeSi2 phase. After USV treatment, the Fe-containing compounds in the Al-17Si-xFe alloys are refined and exist mainly as δ-Al4FeSi2 particles, with average grain size ranging from 26 μm to 37 μm, and only a small amount of β-Al5FeSi phases remain. The mechanism of USV on the morphology of Fe-containing intermetallic compounds was also discussed.

Phase aberration correction in ultrasonic phased array non-destructive testing systems

Phase aberration correction for medical ultrasound systems has attracted a great deal of attention. Since phased array techniques are now widely employed for industrial non-destructive testing （NDT） applications in various fields, the problem of phase aberrations in the process of NDT testing is considered. The technique of cross-covariance for phase aberration correction is presented. The performance of the technique for phase aberration correction is tested by means of echo signals obtained in practical non-destructive testing experiment. The results show that the technique has the better accuracy of phase correction.

Effects of ultrasonic vibration on plastic deformation of AZ31 during the tensile process

An investigation on the plastic behavior of AZ31 magnesium alloy under ultrasonic vibration（with a frequency of 15 kHz and a maximum output of 2 kW） during the process of tension at room temperature was conducted to reveal the volume effect of the vibrated plastic deformation of AZ31.The characteristics of mechanical properties and microstructures of AZ31 under routine and vibrated tensile processes with different amplitudes were compared.It is found that ultrasonic vibration has a remarkable influence on the plastic behavior of AZ31 which can be summarized into two opposite aspects：the softening effect which reduces the flow resistance and improves the plasticity,and the hardening effect which decreases the formability.When a lower amplitude or vibration energy is applied to the tensile sample,the softening effect dominates,leading to a decrease of AZ31 deformation resistance with an increase of formability.Under the application of a high-vibrating amplitude,the hardening effect dominates,resulting in the decline of plasticity and brittle fracture of the samples.

Nondestructive Testing and Characterization of Residual Stress Field Using an Ultrasonic Method

To address the difficulty in testing and calibrating the stress gradient in the depth direction of mechanical components, a new technology of nondestructive testing and characterization of the residual stress gradient field by ultrasonic method is proposed based on acoustoelasticity theory. By carrying out theoretical analysis, the sensitivity coefficients of different types of ultrasonic are obtained by taking the low carbon steel（12%C） as a research object. By fixing the interval distance between sending and receiving transducers, the mathematical expressions of the change of stress and the variation of time are established. To design one sending-one receiving and oblique incidence ultrasonic detection probes, according to Snell law, the critically refracted longitudinal wave（LCR wave） is excited at a certain depth of the fixed distance of the tested components. Then, the relationship between the depth of LCR wave detection and the center frequency of the probe in Q235 steel is obtained through experimental study. To detect the stress gradient in the depth direction, a stress gradient LCR wave detection model is established, through which the stress gradient formula is derived by the relationship between center frequency and detecting depth. A C-shaped stress specimen of Q235 steel is designed to conduct stress loading tests, and the stress is measured with the five group probes at different center frequencies. The accuracy of ultrasonic testing is verified by X-ray stress analyzer. The stress value of each specific depth is calculated using the stress gradient formula. Accordingly, the ultrasonic characterization of residual stress field is realized. Characterization results show that the stress gradient distribution is consistent with the simulation in ANSYS. The new technology can be widely applied in the detection of the residual stress gradient field caused by mechanical processing, such as welding and shot peening.

Measurement of Attenuation of Ultrasonic Propagating through the Thin Layer Media with Time Delay Spectrum

The ultrasonic attenuation coefficient is one of the most important acoustic parameters to character the performance of a thin layer media, but it can not be measured due to mutual superposition of multiple reflected waves at the same interface in ultrasonic testing. Ultrasonic pulse echo and lamb wave to evaluate the thin layer media can not obtain attenuation coefficient at present. In this paper, analytical method was used to study the acoustics characteristic of thin layer media with the ultrasonic echo testing. Meanwhile, the process of ultrasonic attenuation measurement was presented. Simulation and experimental investigation is focused on a thin layer of rubber. Attenuation coefficient was introduced and evaluation mathematics model was established by the two echoes cross-correlation with and without the thin layer media based on the time delay spectrum. It involved the parameters related to the acoustic properties of the thin layer media. Through calculating the sound velocity and acoustic impedance with the evaluation model, it can deduce the relation between the attenuation coefficient and the frequency. Through analyzing the simulation results, it indicated that the attenuation coefficients were invariable with the varying of the frequency. However, the attenuation coefficients increased with the frequency increasing by ultrasonic testing the thin layer of rubber. The reason was that the attenuation factor was not taken into account during the simulation. This method overcomes shortcomings that the traditional ultrasonic testing can not evaluate the thin layer media whose thickness is less than motivation wavelength. It is a new solution to study the attenuation characteristic and on-line nondestructive evaluation in the thin layer media.

Characterization of the key aroma compounds in four varieties of pomegranate juice by gas chromatography-mass spectrometry(GC-MS),gas chromatography-olfactometry(GC-O),odor activity value(OAV),aroma recombination,and omission tests

P omegranate(Punica granatum L.)has attracted considerable attention in world markets due to its valuable nutrients and highly appreciated sensory properties.The aroma profiles of 4 varieties of pomegranate juice,including Dahongtian(DP),Jingpitian(JP),Luyudan(LP),and Tianhonngdan(TP),were investigated via gas chromatography-mass spectrometry(GC-MS)and gas chromatography-olfactometry(GC-O)analyses.A total of 43 volatile compounds were identified by using GC-MS.Among these compounds,16 were considered as potential aroma-active compounds as detected by GC-O.These compounds belonged to the classes of terpinenes,alcohols,and aldehydes.Eleven volatile compounds were defined as the main contributors to the overall aroma of pomegranate juice due to their high odor activity values(OAVs≥1).Aroma recombination and omission tests confirmed thatβ-myrcene,1-hexanol,and(Z)-3-hexen-1-ol were the key aroma compounds,and limonene,1-octen-3-ol,linalool,and hexanal were important aroma-active compounds in DP samples.

Laser ultrasonic testing for near-surface defects inspection of 316L stainless steel fabricated by laser powder bed fusion

The laser powder bed fusion(L-PBF)method of additive manufacturing(AM)is increasingly used in various industrial manufacturing fields due to its high material utilization and design freedom of parts.However,the parts produced by L-PBF usually contain such defects as crack and porosity because of the technological characteristics of L-PBF,which affect the quality of the product.Laser ultrasonic testing(LUT)is a potential technology for on-line testing of the L-PBF process.It is a non-contact and non-destructive approach based on signals from abundant waveforms with a wide frequency-band.In this study,a method of LUT for on-line inspection of L-PBF process was proposed,and a system of LUT was established approaching the actual environment of on-line detection to evaluate the method applicability for defects detection of L-PBF parts.The detection results of near-surface defects in L-PBF 316L stainless steel parts show that the crack-type defects with a sub-millimeter level within 0.5 mm depth can be identified,and accordingly,the positions and dimensions information can be acquired.The results were verified by X-ray computed tomography,which indicates that the present method exhibits great potential for on-line inspection of AM processes.

Micro-destructive assessment of subgrade compaction quality using ultrasonic pulse velocity

The ultrasonic pulse velocity(UPV)correlates significantly with the density and pore size of subgrade filling materials.This research conducts numerous Proctor and UPV tests to examine how moisture and rock content affect compaction quality.The study measures the changes in UPV across dry density and compaction characteristics.The compacted specimens exhibit distinct microstructures and mechanical properties along the dry and wet sides of the compaction curve,primarily influenced by internal water molecules.The maximum dry density exhibits a positive correlation with the rock content,while the optimal moisture content demonstrates an inverse relationship.As the rock content increases,the relative error of UPV measurement rises.The UPV follows a hump-shaped pattern with the initial moisture content.Three intelligent models are established to forecast dry density.The measure of UPV and PSO-BP-NN model quickly assesses compaction quality.

Ultrasonic TOFD testing for aluminum alloy weld of thick plate

The ultrasonic time of flight diffraction (TOFD) testing method for aluminum alloy weld of thick plate was introduced, and the basic defect image features of crack in shape at different positions A, B, C were discussed. The TOFD testing for weld joints was carried out. The results show that the TOFD method has a good measurement accuracy and a good ability of finding the defect of crack in shape.

Decomposition of Organic Compounds in Coke Plant Wastewater by Ultrasonic Irradiation and Its Combined Process

The paper deals with the degradation of the organic compounds in the coke plant wastewater by the combined process of ultrasonic irradiation and activated sludge. The influence factors of the ultrasonic degradation effect such as air atmosphere, initial concentration, ultrasonic power density and the category and consumption of catalyst were investigated. A water quality model was used to explain the degradation of different kinds of organic compounds in the coke plant wastewater by ultrasonic irradiation. After the wastewater was treated by the combined process of ultrasonic irradiation and activated sludge, the COD degradation efficiency was 95.74%, which is 63.49% higher than that by the process of activated sludge alone.

Linear and Nonlinear Ultrasonic Detections of Impact Damage in Composite Laminate

The appearance and accumulation of internal impact damage seriously influence overall performance of carbon fiber reinforced plastic(CFRP).Thus,this study evaluates the change in impact damage number by using linear and nonlinear ultrasonic Lamb wave detection methods,and compares these two detection results.An ultrasonic wave simulation model for composite structure with impact damage is established using the finite element method,and the interaction between impact damage and the ultrasonic wave is simulated.Simulation results demonstrate that the ultrasonic amplitude linearly decreases,and the relative nonlinear parameter linearly increases in proportion to the impact number,respectively.The linear-fitting slope of nonlinear parameter is 0.38 per impact number at an input frequency of 1.0 MHz.It is far higher than that of the linear ultrasonic amplitude,which is only-0.12.However,with the increase of impact damage,the linear growth of nonlinear parameters mainly depends on the decrease in ultrasonic amplitude rather than the accumulation of second harmonic amplitude.In the linear ultrasonic amplitude detection,the linear fitting slope at 1.1 MHz is-0.14,which is lower than those at 0.9 MHz and 1.0 MHz.Meanwhile,in the nonlinear ultrasonic parameter detection,the linear fitting slope at 1.1 MHz is 0.92,which is higher than those at 0.9 MHz and 1.0 MHz.The results show that higher frequencies lead to greater attenuation of ultrasonic amplitude and a larger increase in nonlinear parameters,which can enhance the sensitivity of both linear and nonlinear ultrasonic detections.The accuracy of simulation results is demonstrated through the low-velocity impact and ultrasonic experiments.The results show that compared with nonlinear ultrasonic technology,the linear ultrasonic technology is more suitable for impact damage assessment of carbon fiber reinforced plastic because of its simpler detection process and higher sensitivity.

Ultrasonic Nondestructive Testing of Superplastic Solid-State Welding Joint for Different Steels

Based on quantitative microscopic examinations of welds and welding rate for different steels(40Cr and T10A) joint,which possess the ultra-fine microstructure after high frequency hardening(HFH) and salt-bath cyclic quenching(SCQ),the suitable defect grey scale threshold value was determined,and the welding rate of superplastic solid-state welding of different steels(40Cr and T10 A steel) was systematically inspected and analyzed by means of self-made ultrasonic imaging inspection system.The experimental results showed that the superplastic solid-state weld of different steels can be inspected more accurately,reliably and quickly by this system,and the results were in good accordance with that of metallographic observation.The welding rate of superplastic welding is in linear relation with tensile strength of joint.