Significantly enhanced thermal stability of HMX by phase-transition lysozyme coating

A new robust bio-inspired route by using lysozyme aqueous solution for surface modification on 1,3,5,7-tetranitro-1,3,5,7-tetrazocane(HMX)was described in this paper.HMX crystals were coated by in situ phase transition of lysozyme(PTL)molecules.The HMX decorated by PTL was characterized by SEM,XRD,FTIR and XPS,demonstrating a dense core-shell coating layer.The coverage of lysozyme on HMX crystal was calculated by the ratio of sulfur content.The surface coverage increased from 60.5% to 93.5% when the content of PTL was changed from 0.5 wt% to 2.0 wt%,indicating efficient coating.The thermal stability of HMX was investigated by in situ XRD and DSC.The thermal phase transition temperature of HMX(β to δ phase)was delayed by 42℃ with 2.0 wt% PTL coating,which prevented HMX from thermal damage and sensitivity by the effect of PTL coating.After heating at 215℃,large cracks appeared in the naked HMX crystal,while the PTL coated HMX still maintained intact,with the impact energy of HMX dropped dramatically from 5 J to 2 J.However,the impact energy of HMX with 1.0 wt% and 2.0 wt% coating content(HMX@PTL-1.0 and HMX@PTL-2.0)was unchanged(5 J).Present results potentially enable large-scale fabrication of polymorphic energetic materials with outstanding thermal stability by novel lysozyme coating.

Construction of core@double-shell structured energetic composites with simultaneously enhanced thermal stability and safety performance

The poor thermal stability and high sensitivity severely hinder the practical application of hexanitrohexaazaisowurtzitane(CL-20).Herein,a kind of novel core@double-shell CL-20 based energetic composites were fabricated to address the above issues.The coordination complexes which consist of natural polyphenol tannic acid(TA) and Fe~Ⅲ were chosen to construct the inner shell,while the graphene sheets were used to build the outer shell.The resulting CL-20/TA-Fe~Ⅲ/graphene composites exhibited simultaneously improved thermal stability and safety performance with only 1 wt% double-shell content,which should be ascribed to the intense physical encapsulation effect from inner shell combined with the desensitization effect of carbon nano-materials from outer shell.The phase transition(ε to γ) temperature increased from 173.70 ℃ of pure CL-20 to 191.87℃ of CL-20/TA-Fe~Ⅲ/graphene composites.Meanwhile,the characteristic drop height(H_(50)) dramatically increased from 14.7 cm of pure CL-20 to112.8 cm of CL-20/TA-Fe~Ⅲ/graphene composites,indicating much superior safety performance after the construction of the double-shell structure.In general,this work has provided an effective and versatile strategy to conquer the thermal stability and safety issues of CL-20 and contributes to the future application of high energy density energetic materials.

Further Analysis of Machine Tool Dimensional Accuracy and Thermal Stability under Varying Floor Temperature

Machining is as old as humanity, and changes in temperature in both the machine’s internal and external environments can be of great concern as they affect the machine’s thermal stability and, thus, the machine’s dimensional accuracy. This paper is a continuation of our earlier work, which aimed to analyze the effect of the internal temperature of a machine tool as the machine is put into operation and vary the external temperature, the machine floor temperature. Some experiments are carried out under controlled conditions to study how machine tool components get heated up and how this heating up affects the machine’s accuracy due to thermally induced deviations. Additionally, another angle is added by varying the machine floor temperature. The parameters mentioned above are explored in line with the overall thermal stability of the machine tool and its dimensional accuracy. A Robodrill CNC machine tool is used. The CNC was first soaked with thermal energy by gradually raising the machine floor temperature to a certain level before putting the machine in operation. The machine was monitored, and analytical methods were deplored to evaluate thermal stability. Secondly, the machine was run idle for some time under raised floor temperature before it was put into operation. Data was also collected and analyzed. It is observed that machine thermal stability can be achieved in several ways depending on how the above parameters are joggled. This paper, in conclusion, reinforces the idea of machine tool warm-up process in conjunction with a carefully analyzed and established machine floor temperature variation for the approximation of the machine tool’s thermally stability to map the long-time behavior of the machine tool.

Intrinsic thermal stability of inverted perovskite solar cells based on electrochemical deposited PEDOT

Thermal stability of perovskite materials is an issue impairing the long-term operation of inverted perovskite solar cells(PSCs). Herein, the thermal attenuation mechanism of the MAPb I3films that deposited on two different hole transport layers(HTL), poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)(PEDOT:PSS) and poly(3,4-ethylenedioxythiophene)(PEDOT), is comprehensively studied by applying a heat treatment at 85℃. The thermal stress causes the mutual ions migration of I, Pb and Ag through the device, which leads to the thermal decomposition of perovskite to form Pb I2. Interestingly, we find that I ions tend to migrate more towards electron transport layer(ETL) during heating, which is different with the observation of I ions migration towards HTL when bias pressure is applied. Moreover, the use of electrochemical deposited PEDOT as HTL significantly decreases the defect density of MAPb I3films as compared to PEDOT:PSS supported one. The electrochemical deposition PEDOT has good carrier mobility and low acidity, which avoids the drawbacks of aqueous PEDOT:PSS. Accordingly, the inverted PSCs based on PEDOT show superior durability than that with PEDOT:PSS. Our results reveal detailed degradation routes of a new kind of inverted PSCs which can contribute to the understanding of the failure of thermal-aged inverted PSCs.

Exceptional thermal stability and enhanced hardness in a nanostructured Mg-Gd-Y-Zn-Zr alloy processed by high pressure torsion

A Mg-8.2Gd-3.8Y-1.0Zn-0.4Zr(wt.%) alloy is processed by solution treatment and high pressure torsion(HPT) at room temperature to produce a nanostructured light material with high hardness. The stability of this alloy is subsequently tested through isochronal annealing for 0.5 h at 373 K to 673 K. The results reveal a thermal stability that is vastly superior to that of conventional Mg-based alloys processed by severe plastic deformation: the grain size remains at around 50 nm on heating to 573 K, and as the temperature is increased to 673 K,grain growth is restricted to within 500 nm. The stability of grain refinement of the present alloy/processing combination allowing grain size to be limited to 55 nm after exposure at 573 K, appears to be nearly one order of magnitude better than for the other SPD processed Mg-RE type alloys, and 2 orders of magnitude better than those of SPD processed RE-free Mg alloys. This superior thermal stability is attributed to formation of co-clusters near and segregation at grain boundaries, which cause a thermodynamic stabilization of grain size, as well as formation of β-Mg_(5)RE equilibrium phase at grain boundaries, which impede grain growth by the Zener pinning effect. The hardness of the nanostructured Mg-Gd-Y-Zn-Zr alloy increases with increasing annealing temperature up to 573 K, which is quite different from the other SPD-processed Mg-based alloys. The high hardness of 136 HV after annealing at 573 K is mainly due to solute segregation and solute clustering at or near grain boundaries.

Optimizing the morphology of all-polymer solar cells for enhanced photovoltaic performance and thermal stability

Due to the complicated film formation kinetics, morphology control remains a major challenge for the development of efficient and stable all-polymer solar cells(all-PSCs). To overcome this obstacle, the sequential deposition method is used to fabricate the photoactive layers of all-PSCs comprising a polymer donor PTzBI-oF and a polymer acceptor PS1. The film morphology can be manipulated by incorporating amounts of a dibenzyl ether additive into the PS1 layer. Detailed morphology investigations by grazing incidence wide-angle X-ray scattering and a transmission electron microscope reveal that the combination merits of sequential deposition and DBE additive can render favorable crystalline properties as well as phase separation for PTzBI-oF:PS1 blends. Consequently, the optimized all-PSCs delivered an enhanced power conversion efficiency(PCE) of 15.21%along with improved carrier extraction and suppressed charge recombination. More importantly, the optimized all-PSCs remain over 90% of their initial PCEs under continuous thermal stress at 65 °C for over 500 h. This work validates that control over microstructure morphology via a sequential deposition process is a promising strategy for fabricating highly efficient and stable all-PSCs.

Thermal–moisture dynamics and thermal stability of active layer in response to wet/dry conditions in the central region of the Qinghai–Tibet Plateau,China

The amount of rainfall varies unevenly in different regions of the Qinghai-Tibet Plateau, with some regions becoming wetter and others drier. Precipitation has an important impact on the process of surface energy balance and the energy-water transfer within soils. To clarify the thermal-moisture dynamics and thermal stability of the active layer in permafrost regions under wet/dry conditions, the verified water-vapour-heat coupling model was used. Changes in the surface energy balance, energy-water transfer within the soil, and thickness of the active layer were quantitatively analyzed. The results demonstrate that rainfall changes significantly affect the Bowen ratio, which in turn affects surface energy exchange. Under wet/dry conditions, there is a positive correlation between rainfall and liquid water flux under the hydraulic gradient;water vapour migration is the main form under the temperature gradient, which indicates that the influence of water vapour migration on thermalmoisture dynamics of the active layer cannot be neglected. Concurrently, regardless of wet or dry conditions,disturbance of the heat transport by conduction caused by rainfall is stronger than that of convection by liquid water. In addition, when rainfall decreases by 1.5 times(212 mm) and increases by 1.5 times(477 mm), the thickness of the active layer increases by 0.12 m and decreases by 0.21 m, respectively. The results show that dry conditions are not conducive to the preservation of frozen soil;however, wet conditions are conducive to the preservation of frozen soil, although there is a threshold value. When this threshold value is exceeded, rainfall is unfavourable for the development of frozen soil.

Thermal stability analysis of a satellite-borne optical bench based on quasi-kinematic support

Macao Science Satellite-1(known as MSS-1)is a low-inclination mission that will be launched at the beginning of 2023.An optical bench is used for accessing high-precision strength and direction measurements of the magnetic field.In this paper,we present a thermal stability design for the optical bench based on quasi-kinematic support by kinematic hinges on the MSS-1.The change in angles with the finite element method(FEM)model modified by thermal deformation test data is analyzed.The robustness of the structure is also investigated via the Monte Carlo method.Two main results are obtained.First,the peak-to-peak value(Vp-p)of the inter-boresight angle is at most 1.24″,and the Vp-p of the inter-boresight angle modification and analysis is no more than 3.13″,both of which are better than those on the Swarm satellites in orbit.Second,the 90°fibers of the carbon-reinforced arm need to be strictly controlled during the technological process.

Effect of Ce on the thermal stability of the Ω phase in an Al-Cu-Mg-Ag alloy

This paper studies the effect of Ce on the thermal stability of the Ω phase in an Al-Cu-Mg-Ag alloy by TEM and tensile testing. It has been shown that Ce substantially increases the nucleation density of the Ω phase by acting as the heterogeneous nucleation center. Most impor-tantly,Ce improves the thermal stability of the Ω phase by decreasing the diffusion velocity of Cu atoms and increasing the energy barrier of the thickening ledge nucleation,thus improving the strength of the Al-Cu-Mg-Ag alloy at both room-and elevated-temperatures.

Preparation and characterization of HMX/EVA/hBNNSs microcomposites with improved thermal stability and reduced sensitivity

Hexagonal boron nitride nanosheets(HBNNSs)have huge potential in the field of coating materials owing to their remarkable chemical stability,mechanical strength and thermal conductivity.Thin-layer hBNNSs were obtained by a liquid-phase exfoliation of h-BN powders and incorporated into EVA coatings for improving the safety performance of 1,3,5,7-tetranitro-1,3,5,7-tetrazocane(HMX).HBNNSs and ethylene-vinyl acetate copolymer(EVA)were introduced to HMX by a solvent-slurry process.For comparison,the HMX/EVA and HMX/EVA/graphene(HMX/EVA/G)composites were also prepared by a similar process.The morphology,crystal form,surface element distribution,thermal decomposition property and impact sensitivity of HMX/EVA/hBNNSs composites were contrastively investigated.Results showed that as prepared HMX/EVA/hBNNSs composites were well coated with hBNNSs and EVA,and exhibited better thermal stability and lower impact sensitivity than that of HMX/EVA and HMX/EVA/G composites,suggesting superior performance of desensitization of hBNNSs in explosives.

Influence of zirconium addition on microstructure,magnetic properties and thermal stability of nanocrystalline Nd_(12.3)Fe_(81.7)B_(6.0) alloy

Effect of Zr addition on microstructure, magnetic properties and thermal stability of Nd12.3Fe81.7-xZrxB6.0 (x=0-3.0) ribbons melt-spun and annealed was investigated. Magnetic measurement using vibrating sample magnetometer (VSM) revealed that Zr addition was significantly effective in improving the magnetic properties at room temperature. The intrinsic coercivity Hci of the optimally processed ribbons increased monotonically with increasing Zr content, from 751.7 kA/m for x=0 to 1005.3 kA/m for x=3.0. Unlike the coercivity, the remanence polarization Jr increased first with Zr addition, from 0.898 T up to 1.041 T at x=1.5, and then decreased with further Zr addition. The maximum energy product (BH)max behaved similarly, increasing from 103.1 kJ/m3 to a maximum of 175.2 kJ/m3 at x=1.5. Microstruc- ture studies using atomic force microscopy (AFM) and transmission electron microscopy (TEM) had shown a significant microstructure refinement with Zr addition. The absolute values of temperature coefficients of induction and coercivity were significantly increased with increasing Zr content, indicating that Zr was detrimental to thermal stability of the melt-spun Nd2Fe14B-type material.

Hydrothermal Synthesis,Crystal Structure and Thermal Stability of a Binuclear Copper(Ⅱ) Complex with 3-(Pyridin-2-yl)-1,2,4-triazole

One novel binuclear copper（Ⅱ） complex [Cu 2 （Hpt） 2 （CO 3） 2 （H 2 O） 2 ]·H 2 O with copper carbonate and 3-（pyridin-2-yl）-1,2,4-triazole （Hpt） was hydrothermally synthesized and characterized by IR and X-ray diffraction analysis.The complex crystallizes in triclinic,space group P2 1 /n with a=0.6862（1）,b=0.7805（1）,c=1.1983（2） nm,α=72.03（2）,β=107.72（3）,γ=75.28（2）o,V=0.5884 nm 3,D c=2.105 g/cm 3,Z=1,F（000）=357,GOOF=1.041,the final R=0.01859 and wR=0.04348.The whole molecule is composed of two cooper ions,two Hpt molecules,two carbonate and three water molecules,forming a binuclear structure.The crystal structure shows that the cooper ion is coordinated with three nitrogen atoms from two Hpt molecules,two oxygen atoms from one carbonic acid and one water molecule,forming a distorted square pyramidal geometry.The TG analysis result shows that the title complex is stable under 131.0 ℃.

Effects of Composition and Thermal Cycle on Transformation Behaviors,Thermal Stability and Mechanical Properties of CuAlAg Alloy

The phase transformation behavior, mechanical properties, and the thermal stability of CuAlAg alloy were studied and minor rare earth (0.1 wt pct La+Ce) was added to improve the mechanical property of the studied alloy. It was found that Ag addition in the CuAl binary alloy can improve the stability of martensitic transformation and high Al content leads to the disappearing of martensitic transformation. The tensile strength and strain of the Cu-10.6AI-5.8Ag (wt pct) alloy were measured to be 383.5 MPa and 0.86%, respectively. With rare earth addition, the tensile strain increased from 0.86% to 1.47%. The CuAlAg alloy did not exhibit martensitic transformation on the second heating process. Its poor thermal stability still needs to be improved.

STUDY ON THE SURFACE MODIFICATION OF NANO-TiO_2 BY GRAFTING PMMA/PBMA AND ITS THERMAL STABILITY

The surface of nano-TiO_2 was encapsulated with hydroxyl-propyl-methyl cellulose(HPMC),and then cograftedwith acrylates.Conditions of absorbing and grafting have been studied.Modified nano-TiO_2 particles were characterized byFT-IR spectra,TEM and TG analysis.It was convinced from FT-IR studies that both methyl methacrylate(MMA)and butyl-methacrylate(BMA)were co-grafted onto the surface of nano-TiO_2 particles.TEM images show that the surface of nano-TiO_2 particles was successfully modified by a thick layer of film-like polymer.TG results demonstrate that the decompositiontemperature of HPMC-g-PMMA/PBMA,which has been grafted onto the surface of nano-TiO_2,is 56.9 K higher than that ofHPMC-g-PMMA/PBMA.

Synthesis,Crystal Structure and Thermal Stability of a One-dimensional Chain Cobalt Coordination Polymer [Co(4,4'-bipy)(2,4,6-TMBA)_2(CH_3CH_2OH)_2]_n

A one-dimensional chain cobalt（Ⅱ） coordination polymer with 2,4,6-trimethyl- benzoic acid, 4,4′-bipyridine and cobalt perchlorate anhydrous has been synthesized and characterized in the mixture solvent of water and alcohol. Crystal data for this complex： monoclinic, space group C2/c, a = 2.3805（8）, b = 1.1464（4）, c = 1.5807（5） nm, y = 128.435（4）°, V= 3.3791（18） nm^3, Dc = 1.246 g/cm^3, Z = 4, F（000） = 1340, final GooF = 1.009, R = 0.0504 and wR = 0.1287. Structural analysis shows that the cobalt ion is coordinated with two nitrogen atoms of one 4,4′- bipyridine molecule and four oxygen atoms from two 2,4,6-trimethylbenzoic acid molecules and two alcohol molecules, giving a distorted octahedral coordination geometry. The result of TG analysis indicates that the title complex is stable till 200 ℃.

Synthesis, Crystal Structure and Thermal Stability of a Nickel(Ⅱ) Complex with Bicycle[2.2.1]-2-hepten-5,6-dicarboxylic Acid

The nickel complex {Ni（2,2-bipy）（H2O）3[C8H11O2（COO）]}（H2O）3 with bicycle-[2.2.1]-2-hepten-5,6-dicarboxylic acid [C7H8（COOH）2] and 2,2＇-bipyridine （bipy） as ligands has been synthesized and characterized. It crystallizes in monoclinic, space group P , with a = 0.74975（3）, b = 1.20309（4）, c = 1.30593（4） nm, α = 109.861（2）, β = 98.519（2）, γ = 90.575（2）o, V = 1.09337（7） nm3, Dc = 1.552 g/cm3, Z = 2, F（000） = 524, the final GOOF = 1.064, R = 0.0397 and wR = 0.1171. The crystal structure shows that the nickel ion is coordinated with four oxygen atoms from one bicycle[2.2.1]-2-hepten-5,6-dicarboxylic acid molecule and three water molecules and two nitrogen atoms from the 2,2′-bipyridine molecule, forming a distorted octahedral coordination geometry. The result of TG analysis shows that the title complex is stable under 200.0 ℃.

Thermal stability of different texture components in extruded Mg-3Al-1Zn alloy

Grain growth can modify the texture orientation and the fraction of different texture component.The thermal stability of two texture component in an extruded magnesium AZ31 alloy was investigated.Three types samples with different texture distribution were prepared.The results show that normal grain growth takes place in the magnesium AZ31 alloy during annealing at 300℃ and 450℃.But the grain growth does not lead to the strengthening of either texture component.Both the<0002>⊥ED texture and<0002>//ED texture components show good thermal stability,without influence of the texture volume fraction.The two different texture component possess comparable boundary migration ability,so grains of the two texture component consume indifferently the other grains,or are equally consumed during annealing.

Effect of yttrium on thermal stability and crystallization behavior of Nd_(60)Fe_(20)Al_(10)Ni_(10) amorphous alloys

The effect of yttrium on the thermal stability and crystallization behavior of Nd-Fe-Al-Ni amorphous alloys was investigated using X-ray diffraction （XRD）, differential scanning calorimeter （DSC）, and transmission electron microscopy （TEM）.The results indicated that the as-cast Nd60Fe20Al10Ni10-xYx（X=-0, 2） amorphous alloys were fabricated with some quenched-in crystals, which could be restrained by Y. With the effect of yttrium, both the crystallization temperature and exothermic peak shifted to higher temperatures, illustrating that the thermal stability could be improved. The addition of Y changed the crystallization process and final crystallization results. Moreover, the crystallites in the amorphous matrix became more homogeneous and smaller. Meanwhile, Y was useful for the passivation of oxygen in chemistry and restrained the negative effect of oxygen. The activation energies of the start of crystallization and peaking were 1.21 and 1.16 eV, respectively, according to the Kissinger equation.

Effect of Mo content on the thermal stability of Ti-Mo-bearing ferritic steel

The effects of tempering holding time at 700℃on the morphology,mechanical properties,and behavior of nanoparticles in Ti-Mo ferritic steel with different Mo contents were analyzed using scanning electron microscopy and transmission electron microscopy.The equilibrium solid solution amounts of Mo,Ti,and C in ferritic steel at various temperatures were calculated,and changes in the sizes of nanoparticles over time at different Mo contents were analyzed.The experimental results and theoretical calculations were in good agreement with each other and showed that the size of nanoparticles in middle Mo content nano-ferrite(MNF)steel changed the least during aging.High Mo contents inhibited the maturation and growth of nanoparticles,but no obvious inhibitory effect was observed when the Mo content exceeded 0.37wt%.The tensile strength and yield strength continuously decreased with the tempering time.Analysis of the strengthening and toughening mechanisms showed that the different mechanical properties among the three different Mo content experiment steels were mainly determined by grain refinement strengthening(the difference range was 30-40 MPa)and precipitation strengthening(the difference range was 78-127 MPa).MNF steel displayed an ideal chemical ratio and the highest thermodynamic stability,whereas low Mo content nano-ferrite(LNF)steel and high Mo content nano-ferrite(HNF)steel displayed relatively similar thermodynamic stabilities.