A 300 MW Thermal Unit Start Successfully on First Trial

The complete set of 300 MW No.2 unit of Qingdao Thermal Power Plant started successfully on the first trail up to the national outstanding standard on l

The Linear Formulation of Thermal Unit Commitment Problem with Uncertainties through a Computational Mixed Integer

The solar and wind renewable energy is developing very rapidly to fulfill the energy gap. This specific increasing share of renewable energy is a reaction to the ecological trepidations to conciliate economics with security due to the new challenges in power system supply. In solar and wind renewable energy, the only partially predictable is the output with very low controllability which creates unit commitment problems in thermal units. In this research paper, a different linear formulation via mixed integer is presented that only requires “binary variables” and restraints concerning earlier stated models. The framework of this model allows precisely the costs of time-dependent startup & intertemporal limitations, for example, minimum up & down times and a ramping limit. To solve the unit commitment problem efficiently, a commercially available linear programming of mixed-integer is applied for sizeable practical scale. The results of the simulation are shown in conclusions.

SIMULATION IN THERMAL DESIGN FOR ELECTRONIC CONTROL UNIT OF ELECTRONIC UNIT PUMP

The high working junction temperature of power component is the most common reason of its failure. So the thermal design is of vital importance in electronic control unit （ECU） design. By means of circuit simulation, the thermal design of ECU for electronic unit pump （EUP） fuel system is applied. The power dissipation model of each power component in the ECU is created and simulated. According to the analyses of simulation results, the factors which affect the power dissipation of components are analyzed. Then the ways for reducing the power dissipation of power components are carried out. The power dissipation of power components at different engine state is calculated and analyzed. The maximal power dissipation of each power component in all possible engine state is also carried out based on these simulations. A cooling system is designed based on these studies. The tests show that the maximum total power dissipation of ECU drops from 43.2 W to 33.84 W after these simulations and optimizations. These applications of simulations in thermal design of ECU can greatly increase the quality of the design, save the design cost and shorten design time

Thermal Model of High-Speed Spindle Units

For the purpose to facilitate development of high-speed Spindle Units (SUs) running on rolling bearings, we have developed a beam element model, algorithms, and software for computer analysis of thermal characteristics of SUs. The thermal model incorporates a model of heat generation in rolling bearings, a model of heat transfer from bearings, and models for estimation of temperature and temperature deformations of SU elements. We have carried out experimental test and made quantitative evaluation of the effect of operation conditions on friction and thermal characteristics of the SUs of grinding and turning machines of typical structures. It is found that the operation conditions make stronger effect on SU temperatures when rpm increases. A comparison between the results of analysis and experiment proves their good mutual correspondence and allows us to recommend application of the models and software developed for design and research of high-speed SUs running on rolling bearings.

Research on Operation of Electrothermal Integrated Energy System Including Heat Pump and Thermal Storage Units Based on Capacity Planning

In view of the Three North areas existing wind power absorption and environment pollution problems,the previous scholars have improved the wind abandon problem by adding electrothermal coupling equipment or optimizing power grid operation.In this paper,an electrothermal integrated energy system including heat pump and thermal storage units was proposed.The scheduling model was based on the load data and the output characteristics of power units,each power unit capacity was programmed without constraints,and the proposed scheduling model was compared with the traditional combined heat and power scheduling model.Results showed that the investment and pollutant discharge of the system was reduced respectively.Wind power was fully absorbed.Compared with the traditional thermal power unit,the proportion of the output was significantly decreased by the proposed model.The proposed system could provide a new prospect for wind power absorption and environment protection.

Research on the Prediction of Load Regulation Capacity for Supercritical Thermal Power Unit

Both the modeling and the load regulation capacity prediction of a supercritical power plant are investigated in this paper. Firstly, an indirect identification method based on subspace identification method is proposed. The obtained identification model is verified by the actual operation data and the dynamic characteristics of the system are well reproduced. Secondly, the model is used to predict the load regulation capacity of thermal power unit. The power, main steam pressure, main steam temperature and other parameters are simulated respectively when the unit load is going up and down. Under the actual constraints, the load regulation capacity of thermal power unit can be predicted quickly.

The Impact of Thermal Desorption Unit Associated with Remediation of Hydrocarbon Impacted Soils on Air Quality at Beneku, Ndokwa East, Delta State, Nigeria

The study is on the use of thermal desorption unit in the remediation of contaminated soils located at Beneku in Ndokwa East local government area of Delta state. This method uses heat to vaporize the contaminants, and as such only works for volatile contaminants. Air quality samples around the thermal desorption Unit (TDU), used for the treatment of hydrocarbon impacted soils were taken at six (6) different sampling points (Stations). The sampling points were 100 m apart beginning from 0 m which was the closest to the TDU. The results showed that the mean values of SO2 were 0.01 ppm for both the dry and wet seasons and it is within the FMEnv limit of 0.01. The mean concentration of NO2 in the dry season was 0.25 μg/m3 and in the wet season it was 0.18 μg/m3, which were above the FMEnv limit of 0.06 μg/m3. It is a strong oxidizing agent that reacts with air/water to form corrosive nitric acid, as well as toxic organic nitrates. The mean concentration of CO2 recorded in the dry season was 11.52 ppm and that for the wet season was 10.53 ppm, which were slightly above the FMEnv limit of 10.00 ppm. The levels of SPM 2.5 recorded in the study show a concentration of 132.07 μg/m3 in the dry season and 95.93 μg/m3 in the wet season while those for SPM 10 had 102.17 μg/m3 in the dry season and 91.33 μg/m3 in the wet season. The level of the VOC recorded across the study area was significantly low (0.11 μg/m3). The mean H2S concentration recorded across the study area was low (0.01 μg/m3). Several health risks have been associated with SPM. Inhaling SPM affects respiratory and cardiovascular systems in both children and adults. Fine SPM (such as PM 2.5 particulate) can penetrate into the lungs and blood streams when inhaled, resulting to respiratory problems, heart attack, lung cancer and even death, while exposure to low levels of H2S can induce headaches as well as breathing difficulties in some asthmatic patients.

500 MW Unit Simulator for Panshan Thermal Power Plant Passed Acceptance

After a thorough demonstration in Panshan Thermal Power Plant, the 500 MW super critical pressure unit simulator developed by the Simulation & Control Institute under the North China University of Electric Power was accepted by experts from the North China Electric Power Group Company on 3rd August 1996.

基于蝙蝠优化算法的电力系统经济调度

针对电力系统的优化调度问题,提出基于蝙蝠优化算法的运行策略,旨在降低发电机组的总燃料成本和减少污染物排放量.然而由于约束条件的复杂性,一般的数学方法难以解决这个难题.采用优化过的蝙蝠算法(NBA)来解决电力系统动态经济调度问题,为了验证优化过的NBA算法的性能,对一个含有6台火电机组的电力系统进行优化调度,并在Matlab软件中对模型进行了仿真和测试.以运行成本最小为目标函数,约束条件包含功率平衡约束、火电机组最大最小出力约束、火电机组爬坡约束、网络潮流约束等,然后使用NBA算法完成对电力系统优化调度决策任务,结果表明,优化过后的算法减少污染的同时降低了发电成本,提升了电力系统的效益.

集成蓄热装置的火电机组调峰特性分析

【目的】随着新能源的大规模发展,新能源出力不确定性和波动性问题展现出来,而为了弥补新能源出力缺点,火电机组承担起了调峰作用。为了提升火电机组的调峰能力,对其调峰特性进行了研究。【方法】首先,以某350 MW供热机组作为分析对象,应用仿真软件搭建热力系统模型,并验证该模型的精确性。其次,以蓄热系统为辅助系统,研究机组在满足供热需求情况下的机组调峰能力,并分析蓄热等储能单元对机组调峰能力的影响。最后,采用启发式粒子群算法对蓄热水罐运行策略进行优化,得到随热负荷变化的储热罐最优运行模式。【结果】通过蓄热水罐与火电机组耦合的方法有效提升了机组的调峰和供热能力,并提出可以根据实际热负荷数据确定最大化收益的运行模式。【结论】该方法对机组的运行策略具有指导意义。

火电耦合压缩空气储能技术研究进展及展望

火电耦合压缩空气储能技术作为一种提升传统火电机组灵活性和经济性的有效手段,近年来受到了广泛关注。该文从分析火电耦合压缩空气储能技术在提升电网调峰能力、促进可再生能源整合等方面的重要意义出发。首先,介绍典型耦合系统的结构组成与工作原理;然后,探讨耦合系统中关键设备的技术现状和面临的挑战;之后,梳理火-储耦合系统的集成方案设计、调峰运行优化以及经济性评估的研究现状;最后,针对当前技术难点,展望未来火电耦合压缩空气储能技术的研究方向与重点。该文旨在为今后相关领域研究提供参考与借鉴,推动其持续发展和创新。

飞轮储能辅助火电机组一次调频及其性能评价

为促进太阳能、风能等新能源消纳,进一步拓宽火电储能技术升级和灵活性改造渠道,助力双碳目标和新型电力系统建设,提出增设储能系统辅助火电机组调频以解决火电机组爬坡慢、机组振荡不稳定等问题。基于国内外研究现状,提出机组以及储能系统荷电状态出力控制策略模型,通过Matlab/Simulink搭建两区域电网进行模拟仿真。结果表明,在阶跃扰动下区域1机组耦合1 MW飞轮储能系统后,峰值降至1.93×10^(-3)pu,降低4×10^(-4) pu,占原频率波动率的9.39%,机组实际出力从2.45×10^(-2)pu降至1.61×10^(-2)pu,降低34%。结果表明,在外界相同扰动条件下,采用飞轮储能辅助火电机组调频可有效减小系统频率波动量,减少汽轮机输出功率波动,提升调频性能。

基于麻雀算法优化支持向量机的NOx浓度预测

煤炭作为火电厂发电的主要能源,其在锅炉内焚烧过程中会产生大量的氮氧化物。各电厂一般利用烟气自动监控系统对其浓度进行实时测量,但由于测量时存在较大迟延,不能准确地反映SCR系统NOx浓度的实时变化。因此提出了一种基于改进麻雀算法优化最小二乘支持向量机的NOX浓度预测方法。首先,引入余弦因子改进麻雀算法中的比例算子,将迭代次数信息引入到迭代过程中,平衡算法前后期的全局与局部搜索能力。其次,使用新的变异算子代替原算子,将混沌理论融合到麻雀算法,解决了算法全局搜索能力较差、初始化麻雀分布不稳定及发现者位置更新方式不足的问题。最后,采用改进麻雀算法(CDE-SSA)对最小二乘支持向量机(LSSVM)进行参数寻优。实验结果证明,方法在NOX浓度预测的精度和稳定性上均表现出了良好的性能。

基于火电灵活性改造的可再生能源消纳系统成本优化

随着风电等可再生能源的大规模发展,带来了消纳难等新挑战,通过火电灵活性改造可以增强电力系统灵活调节能力、提升可再生能源消纳空间,同时需要考虑火电灵活性改造的经济性和对可再生能源消纳的影响。因此,综合考虑火电机组常规运行成本及灵活性改造后增加的各项成本,结合碳排放成本和弃风成本,建立以总成本最小为目标的火电灵活性改造前后优化调度模型,采用对比差值法计算基于火电灵活性改造的可再生能源消纳系统成本。通过算例,将所建模型应用于对比改造前后、不同碳排放强度、是否考虑弃风等不同方案下的机组运行状况及消纳系统成本大小,并拟合得到可再生能源渗透率和消纳系统成本的关系曲线,验证了模型的有效性。

基于逐次变分模态分解的飞轮-火电一次调频控制策略

随着新型电力系统的大力建设与推广,火电机组面临的调频压力增大,提出一种逐次变分模态分解的飞轮-火电一次调频控制策略。首先,以飞轮储能和火电机组为研究对象,建立考虑新能源占比的飞轮-火电一次调频模型;其次,将一次调频功率指令利用逐次变分模态方法分解,由火电机组响应分解后的低频功率指令,同时设计飞轮储能下垂优化控制方法,实现飞轮储能与火电机组响应频率变化的协同控制;最后在不同工况下仿真验证,结果表明所提策略可有效避免火电机组一次调频时的频繁出力,减小火电机组响应频率变化时的调控要求,同时可最大限度地利用飞轮储能调频容量并保证飞轮储能调频期间的运行安全,进一步提升了系统的频率响应能力。

双碳目标下高温气冷堆替代中小型火电的思考

碳达峰碳中和是我国一项重要的国家战略决策,“双碳”目标的提出给能源行业带来了深刻的变革,我国能源结构将进一步优化,电力行业必须实现低碳转型,新能源取代火电已成为必然。本文分析了新形势下火电企业面临的巨大挑战、发电规模受到限制、经营成本不断上升,尤其是中小型火电机组,面临着淘汰和关停的局面,而高温气冷堆具有固有安全性、发电效率高、用途广泛的显著特点,使其替代中小型火电成为可能。本文通过厂址适应性、技术可行性、经济可行性三方面,分析了高温气冷堆替代中小型火电的可行性,并从相关法律法规适用性、内陆厂址所带来的问题、开展公众沟通等方面提出建议。