Effect of Weft Binding Structure on Compression Properties of Three-Dimensional Woven Spacer Fabrics and Composites

With the wide use of three-dimensional woven spacer composites(3DWSCs),the market expects greater mechanical properties from this material.By changing the weft fastening method of the traditional I-shape pile yarns,we designed three-dimensional woven spacer fabrics(3DWSFs)and 3DWSCs with the weft V-shape to improve the compression performance of traditional 3DWSFs.The effects of weft binding structures,V-pile densities,and V-shaped angle were investigated in this paper.It is found that the compression resistance of 3DWSFs with the weft V-shape is improved compared to that with the weft I-shape,the fabric height recovery rate is as high as 95.7%,and the average elastic recovery rate is 59.39%.When the interlayer pile yarn density is the same,the weft V-shaped and weft I-shaped 3DWSCs have similar flatwise pressure and edgewise pressure performance.The compression properties of the composite improve as the density of the V-pile yarns increases.The flatwise compression load decreases as the V-shaped angle decreases.When the V-shaped angle is 28°and 42°,the latitudinal V-shaped 3DWSCs perform exceptionally well in terms of anti-compression cushioning.The V-shaped weft binding method offers a novel approach to structural design of 3DWSCs.

MODELING OF LIGHT SPECULAR REFLECTION FROM PLAIN-KNITTED FABRICS: A THREE-DIMENSIONAL ANALYSIS

The paper applies a mathematical model[1] for specular reflection to plain-knitted fabrics by using a three-dimensional analysis. Computer simulation of goniophotometric curves is generated based oa the model. Correction factors are introduced by taking into consideration of geometry of the instrument used. Comparison between the simulated and the measured curves of a straight monofilament yarn with various orientation angles is carried out and reasonable agreement has been obtained.

Three-Dimensional Measurement and Reconstruction of Fabric Drape Shape

This paper introduces a new method of measuring the three-dimensional drape shape of fabrics with structural light. First, we apply parallel annular structural light to form light and shade alternating contour stripes on the surface of fabrics. We then collect the images of contour stripes using Charge Coupled Device (CCD). Subsequently, we process the images to identify the contour stripes and edges of fabrics, and obtain the fabric contour lines of curved surfaces. Finally, we apply three-dimensional curved surface modeling method based on a network of polar coordinates, and reconstruct the three-dimensional drape shape of fabrics. Experiments show that our method is effective in testing and reconstructing three-dimensional drape shape of fabrics.

Mechanical Properties of Three-Dimensional Fabric Sandwich Composites

Three-dimensional( 3 D) fabric composite is a newly developed sandwich structure,consisting of two identical parallel fabric decks woven integrally and mechanically together by means of vertical woven fabrics. In this paper,six types of 3 D fabric sandwich composites were developed in terms of compressive and flexural properties as a function of pile height( 10, 20 and30 mm) and pile distance( 16, 24 and 32 mm) in pile structures. The mechanical characteristics and the damage modes of the 3 D fabric sandwich composites under compressive and flexural load conditions were investigated. Besides,the influence of pile height and pile distance on the 3 D fabric sandwich composites mechanical properties was analyzed. The results showed that the compressive properties decreased with the increase of the pile height and the pile distance. Flexural properties increased with the increase of pile height, while decreased with the increase of pile distance.

Fabrication and formation mechanism of NbC_x-C three-dimensional netted fibers

Micrometer NbC_x-C three-dimensional netted fibers were synthesized by thecarbothermal method under 0.1 MPa of N_2 ambient atmosphere at a relatively low temperature. Rawmaterials were commercial powders of Nb_2O_5 (99.95 percent), reactive carbon (99.99 percent), NaCl(99.95 percent) and sucrose (99.94 percent). The relationship of the fabrication processing with thecomposition, crystal structure and morphology of fibers was investigated. The formation mechanismwas also proposed and discussed.

F127 assisted fabrication of Ge/r GO/CNTs nanocomposites with three-dimensional network structure for efficient lithium storage

To solve the volume expansion and poor electrical conductivity of germanium-based anode materials,Ge/rGO/CNTs nanocomposites with three-dimensional network structure are fabricated through the dispersion of polyethylene-polypropylene glycol(F127)and reduction of hydrogen.An interesting phenomenon is discovered that F127 can break GeO_(2)polycrystalline microparticles into 100 nm nanoparticles by only physical interaction,which promotes the uniform dispersion of GeO_(2)in a carbon network structure composed of graphene(rGO)and carbon nanotubes(CNTs).As evaluated as anode material of Lithium-ion batteries,Ge/rGO/CNTs nanocomposites exhibit excellent lithium storage performance.The initial specific capacity is high to 1549.7 mAh/g at 0.2 A/g,and the reversible capacity still retains972.4 mAh/g after 100 cycles.The improved lithium storage performance is attributed to that Ge nanoparticles can effectively slow down the volume expansion during charge and discharge processes,and threedimensional carbon networks can improve electrical conductivity and accelerate lithium-ion transfer of anode materials.

3D Modeling and Simulation of Fancy Fabrics in Weft Knitting

Weft knitted fancy fabrics are widely used in knitted garment design. Due to the complexity of the structures, their modeling and simulation needs to be solved in three-dimensional (3D) CAD developments. In this paper, 3D loop geometrical models of weft knitted fancy structures, including tuck stitch, jacquard stitch, transfer stitch and fleecy stitch, were developed based on an improved model of plain loop, and their central axes as some 3D space curves were achieved by using Non-Uniform Rational B-Splines (NURBS). The 3D visual simulation programme was written in C++ programming language using OpenGL, which was a function library of 3D graphics. Some examples of weft knitted fancy fabrics were generated and practical application of 3D simulation was discussed.

Reconfigurable directional coupler in lithium niobate crystal fabricated by three-dimensional femtosecond laser focal field engineering

For crystals, depressed cladding waveguides have advantages such as preservation of the spectroscopic as well as non-linear properties and the capability to guide both horizontal and vertical polarization modes, but fabrication is always quite time consuming. In addition, it is usually difficult to couple modes propagating in different depressed cladding waveguides through evanescent field overlap, so it is often required to dynamically reconfigure photonic waveguide devices using external fields for classical or quantum applications. Here, we experimentally demonstrate the single-scan femtosecond laser transverse writing of depressed cladding waveguides to form a 2 × 2 directional coupler inside lithium niobate crystal, which is integrated with two deeply embedded microelectrodes on both sides of the interaction region to reconfigure the coupling. By focal field engineering of the femtosecond laser, we specially generate a three-dimensional longitudinally oriented ring-shaped focal intensity profile composed of 16 discrete spots to simultaneously write the entire cladding region. The fabricated waveguides exhibit good single guided modes in two orthogonal polarizations at 1550 nm. By applying voltage to the deeply embedded microelectrodes fabricated with the femtosecond laser ablation followed by selective electroless plating, we successfully facilitate the light coupling from the input arm to the cross arm and thus actively tune the splitting ratio. These results open new important perspectives in the efficient fabrication of reconfigurable complex three-dimensional devices in crystals based on depressed cladding waveguides.

Emplacement Mechanism of the Akebasitao Pluton:Implications for Regional Tectonic Evolution of West Junggar,NW China

Late Carboniferous to Early Permian A-type granites are extensively distributed throughout the West Junggar region, NW China, and the Akebasitao pluton is extremely distinguished among these plutons. In this paper, we reported new anisotropy of magnetic susceptible （AMS） data combine with detailed field study and audio magnetotelluric （AMT） sounding to assess the three-dimensional shape and magmatic emplacement mechanism of the Akebasitao pluton. The geological features and the AMT sounding indicate that the pluton had a slightly oblique movement of magma from northwest to southeast, which was most likely to correspond to an asymmetrical torch with a laccolith-shaped upper part, and a lower part formed by sub-vertical ＂root＂ that was located within its northwestern part, probably controlled by the NE-trending Anqi fault. The AMS fabrics of all the specimens reveal a low Pj value （mean of 1.02） and a low T value （mean of -0.024）, suggesting that the deformation of the AMS ellipsoid is relatively weak. The specimens exhibit both oblate and prolate shapes of the AMS ellipsoid. Magnetic lineations and foliations are randomly distributed throughout the pluton without any preferred orientation. These AMS patterns indicate that the pluton formed in a relatively stable structural environment with no regional extrusion. Therefore, we propose a complex emplacement process in which the magmas reached the shallower crust levels via deep-faults and subsequently occupied the room created by doming, accompanied by stoping near the pluton roof. Additionally, the regional tectonic setting was relatively stable during the emplacement of the Akebasitao pluton, indicating the termination of compressional orogeny during the late Late Carboniferous in the West Junggar region. This conclusion perfectly coincides with the regional tectonic paleogeography, magmatic system, and paleostress field.

Liquid deposition photolithography for submicrometer resolution three-dimensional index structuring with large throughput

Photonic devices increasingly require three-dimensional control of refractive index,but existing fabrication methods such as femtosecond micromachining,multilayer lithography and bulk diffusion can only address a select scale range,are often limited in complexity or thickness and have low throughput.We introduce a new fabrication method and polymeric material that can efficiently create mm^(3) optical devices with programmable,gradient index of refraction with arbitrary feature size.Index contrast of 0.1 is demonstrated,which is 100 times larger than femtosecond micromachining,and 20 times larger than commercial holographic photopolymers.This is achieved by repetitive microfluidic layering of a self-developing photopolymer structured by projection lithography.The process has the unusual property that total fabrication time for a fixed thickness decreases with the number of layers,enabling fabrication 10^(5) faster than femtosecond micromachining.We demonstrate the process by sequentially writing 100 layers to fabricate a mm thick waveguide array.

Fabrication and morphology of NbC_x-C composite three-dimensinal netted fibers

The raw materials were commercial powders of Nb2O5 (99.95%), reactive carbon (99.99%), NaCI (99.95%) and sucrose (99.94%). By the carbothermal method, the NbCx (x= 0.98)-C composite three-dimensional netted fibers were prepared in graphite resistance furnace in 0.1 MPa/N2 ambient atmosphere at temperature from 970 to 1 120℃. The diameters of composite three-dimensional netted fibers are 12-38 μm, the hole circumferences of netted fibers are 0.22-2.2 mm, and the hole diameters are 70-701 μm. The process conditions for fabricating NbCx-C composite three-dimensional netted fibers and related morphology, composition and crystal structure of NbCx-C composite netted fibers were investigated in detail.

A shortcut to marking 3D target curves on curved surface via a galvanometric laser scanner

Marking arbitrary three-dimensional(3D) target curves on given objects with curved surface is required in many industrial fields, such as fabric prepreg placement in composite material part fabrication, product assembly, surface painting for decoration, etc. A shortcut to the solution of this intractable problem is proposed by utilizing a galvanometric laser scanner(GLS) with the aid of a camera. Without using the existing tedious GLS calibration procedures,the proposed method directly establishes a mapping between the 3D coordinates of the laser spots on the object surface and the control voltages of the scanner. A single-hidden layer feedforward neural network(SLFN) is employed to model the mapping. By projecting a dense grid of laser spots on the object to be marked and simultaneously taking only one image, the SLFN model is trained in minutes via a linear solving mechanism. Experiments demonstrate that the trained SLFN model has a good generalization performance for marking 3D target curves. The 3D laser marking errors on experimental objects are less than 0.5 mm. The proposed method is especially suitable for on-site use and can be conveniently extended to multiple GLSs for marking large complex objects.