Quaternary Oxide of Cerium, Terbium, Praseodymium and Zirconium for Three-Way Catalysts

Oxygen storage-capacity （OSC）, oxygen buffer capacity （OBC）, X-my diffraction and electron diffraction pattern, high resolution electron microscopy were used to study the quaternary oxides, i .e., of Ce, Tb, Pr and Zr. （Ce0.6 Tb0.2Zr0.2O2- δ and Ce0.6Pr0.2Zr0.2O2-δ ）. OSC and OBC data indicate that these oxides have very good oxygen transfer capacity （OTC） and their pseudo-solid solutions exhibit fluorite-type structure. These oxides may act as a good candidate for three-way catalysts （TWC）.

Influences of (Ce-Zr-La-Pr)O Contents on Three-Way Catalyst Performances

A series of catalysts with (Ce-Zr-La-Pr)O contents range from 0 to 50% in coating and single-palladium loads on substrates were prepared to study effects of (Ce-Zr-La-Pr)O contents on catalytic activities and durability by contrasting the characteristics of light-off, A/F and catalytic conversions of the fresh catalysts with that of the aged catalysts. The results show that (Ce-Zr-La-Pr)O can enhance the catalysts light-off characteristics, widen A/F windows and increase catalytic conversions at a certain extent through optimizing physical structural and chemical property of the mixed coating. However, (Ce-Zr-La-Pr)O contents influence greatly on the catalysts activities and durability, and the catalysts with contents ranging from 10% to 30% exhibited better integrative properties in all samples, and 10% was the optical content to make the catalyst performance highest in this thesis. It is indicated that an suitable content of (Ce-Zr-La-Pr)O plays an important role in assisting catalysis, enhancing durability and increasing oxygen storage capability.

Regulated and Speciated Hydrocarbon Emissions from a Dual Fuel Light Duty Vehicle with and Without a Three-Way Catalyst

The regulated pollutants （CO,HC and NOx） and unregulated pollutants （volatile organic compounds and carbonyl compounds）,emitted from a dual fuel vehicle fueled with gasoline and E10 fuel,are measured under a transient cycle and steady modes.The impacts of a three-way catalyst （TWC） are investigated for the two types of fuels.The measured results show that NOx and acetaldehyde emitted from the E10-fueled car are much more than that from the gasoline-fueled car under the same modes.On the basis of maximum incremental reactivity （MIR） factors and emissions of organic gases,the ozone specific reactivity of the tailpipe gases are evaluated.

Influence of Ce_(0.35)Zr_(0.55)Y_(0.10) Solid Solution on Performance of Pt-Rh Three-Way Catalysts

Ce0.35Zr0.55Y0. 10 solid solution was prepared by co-precipitation technique and characterized by specific surface area measurements （BET） and X-ray diffraction （XRD）. Ce0.35Zr0.55Y0.10 was used to prepare low Pt-Rh threeway catalyst （TWC）, and its influence on the performance of TWC was investigated. The results revealed that Ce0.35 Zr0.55Y0.10 had a cubic structure similar to Ce0.50Zr0.50O2 and its specific surface area can maintain higher than Ce0.50 Zr0.50O2 after 1000 ℃ calcination for 5 h. Being hydrothermal aged at 1000 ℃ for 5 h, the catalyst containing Ce0.35 Zr0.55Y0.10 still exhibited higher conversion of C3H8, CO and NO and lower light-off temperature in comparison with Ce0.50Zr0.50O2 TWC.

Promoter of (Ce-Zr)O_2 Solid Solution Modified by Praseodymia in Three-Way Catalysts

The three way catalysts (TWCs) promoters (Ce Zr)O 2, (Pr Ce Zr)O 2 and (Pr Zr)O 2 were prepared by sol gel like method. They were characterized by XRD, EXAFS and BET surface area determination. The reduction features of the promoters were measured by temperature programmed reduction (TPR) of H 2 to access the potential for the promoters containing praseodymia as oxygen storage component in three way catalyst. The (Pr Zr)O 2 cubic solid solution is formed at high temperature up to 800 ℃, which makes it more reducible than the (Ce Zr)O 2 solid solution. For the (Pr Ce Zr)O 2 samples, the ternary solid solution plays an important role in the reduction process. The performance of the three way catalysts with fully formulated Pt, Pd and Rh is proceeded by using both light off temperature under a stoichiometric gas composition and the conversion of CO, C 3H 6 and NO under changing air/fuel ratio at a constant reaction temperature 400 ℃ . The results indicate that a small amount of praseodymia doping into (Ce Zr)O 2 favors the light off temperature of C 3H 6 and NO, and all the catalysts containing praseodymia obviously exhibits enhanced width of S value for NO conversion at lean region ( S ≥1.00).

Effect of Sulfur on the Performance of Three-Way Catalysts

Sulfur content is one of the fuel properties to be monitored. Sulfur dioxide, the major product derived from organic sulfur compounds in the exhaust gas emissions, is a poison to the three-way catalysts (TWC). A gas mixture was applied to simulate the exhaust gases used in the TWC aging procedure tests. Two types of the TWC, REX-ⅡC and REX-ⅡD, were tested in this study. The performance of both TWC's before and after the 100-hour sulfur aging program was compared. It was concluded that the Pt component in the TWC was apt to be poisoned by sulfur much easily than Rh. The performance of the REX-ⅡD catalyst was generally better than that of the REX-ⅡC catalyst.

Low-content and highly effective zoned Rh and Pd three-way catalysts for gasoline particulate filter potentially meeting Euro 7

The next-generation Euro 7 standard proposed much lower pollutant limits from gasoline vehicles,specifically for CO and NO_(x),which would be challenging for the three-way catalysts(TWCs)utilized commercially to eliminate these pollutants.TWCs with reductive(Rh)and oxidative(Pd)active components on gasoline particulate filters(TWC on GPF)play importantly auxiliary roles in the remediation of CO and NO_(x)downstream the close coupled TWCs to meet their emission targets.Here,a low-content Rh-based TWC(0.17 wt%)zoned with a less expensive Pd-based TWC(0.29 wt%)for GPF applications(cGPF)is reported using improved colloidal deposition method.The supporting of Rh on Y-stabilized ZrO_(2)rather than on CeO_(2)-ZrO_(2)inhibits the formation of inactive Ce rhodate species,while Pd on CeO_(2)-ZrO_(2)not only guarantees the high oxygen storage capacity(OSC)but also enhances catalytic activity.The layout of the front one-fifth in volume being 0.29 wt%Pd on Ce_(0.43)Zr_(0.5)7O_(2)and the rear four-fifths being 0.17 wt%Rh on Zr_(0.85)Y_(0.15)O_(2)prevents the possible alloying of Rh with Pd.The highly effective zoned Rh and Pd TWCs show synergistic three-way activity before and after severe hydrothermal aging at 1000℃with 10%water for24 h,which could be potential choices for close coupled GPF application to satisfy the upcoming stringent emission standards,such as Euro 7 and China 6b.

光学体表成像设备Catalyst的故障维修案例及日常保养方法

本文介绍了光学体表成像设备Catalyst HD的工作原理,以及处理常见的硬件和软件故障的方法,并提供了日常维护保养方法。其中,对于硬件故障,利用Catalyst HD系统的MutilZsn软件来判断Catalyst投影器和摄像头故障,对于软件故障方面,探讨了Catalyst HD系统在医用直线加速器上常见的Authorization Pending联锁问题的触发原因。本文为科室更好地开展光学体表引导放疗技术,高效地运用好设备提供参考意见。

Catalytic effect in lithium metal batteries: From heterogeneous catalyst to homogenous catalyst

Lithium metal batteries are regarded as prominent contenders to address the pressing needs owing to the high theoretical capacity.Toward the broader implementation,the primary obstacle lies in the intricate multi-electron,multi-step redox reaction associated with sluggish conversion kinetics,subsequently giving rise to a cascade of parasitic issues.In order to smooth reaction kinetics,catalysts are widely introduced to accelerate reaction rate via modulating the energy barrier.Over past decades,a large amount of research has been devoted to the catalyst design and catalytic mechanism exploration,and thus the great progress in electrochemical performance has been realized.Therefore,it is necessary to make a comprehensive review toward key progress in catalyst design and future development pathway.In this review,the basic mechanism of lithium metal batteries is provided along with corresponding advantages and existing challenges detailly described.The main catalysts employed to accelerate cathode reaction with emphasis on their catalytic mechanism are summarized as well.Finally,the rational design and innovative direction toward efficient catalysts are suggested for future application in metal-sulfur/gas battery and beyond.This review is expected to drive and benefit future research on rational catalyst design with multi-parameter synergistic impacts on the activity and stability of next-generation metal battery,thus opening new avenue for sustainable solution to climate change,energy and environmental issues,and the potential industrial economy.

Fullerenes and derivatives as electrocatalysts: Promises and challenges

Carbon-based metal-free nanomaterials are promising alternatives to precious metals as electrocatalysts of key energy storage and conversion technologies.Of paramount significance are the establishment of design principles by understanding the catalytic mechanisms and identifying the active sites.Distinct from sp2-conjugated graphene and carbon nanotube,fullerene possesses unique characteristics that are growingly being discovered and exploited by the electrocatalysis community.For instance,the well-defined atomic and molecular structures,the good electron affinity to tune the electronic structures of other substances,the intermolecular self-assembly into superlattices,and the on-demand chemical modification have endowed fullerene with incomparable advantages as electrocatalysts that are otherwise not applicable to other carbon ma-terials.As increasing studies are being reported on this intriguing topic,it is necessary to provide a state-of-the-art overview of the recent progress.This review takes such an initiative by summarizing the promises and challenges in the electrocatalytic applications of fullerene and its derivatives.The content is structured according to the composition and structure of fullerene,including intact fullerene(e.g.,fullerene composite and superlattices)and fullerene derivatives(e.g.,doped,endohedral,and disintegrated fullerene).The synthesis,characterization,catalytic mechanisms,and deficiencies of these fullerene-based materials are explicitly elaborated.We conclude it by sharing our perspectives on the key aspects that future efforts shall consider.

Efficient and stable PtFe alloy catalyst for electrocatalytic methanol oxidation with high resistance to CO

Direct methanol fuel cells(DMFC) are widely considered to be an ideal green energy conversion device but their widespread applications are limited by the high price of the Pt-based catalysts and the instability in terms of surface CO toxicity in long-term operation.Herein,the PtFe alloy nanoparticles(NPs) with small particle size(~4.12 nm) supported on carbon black catalysts with different Pt/Fe atomic ratios(Pt_(1)Fe_(2)/C,Pt_(3)Fe_(4)/C,Pt_(1)Fe_(1)/C,and Pt_(2)Fe_(1)/C) are successfully prepared for enhanced anti-CO poisoning during methanol oxidation reaction(MOR).The optimal atomic ratio of Pt/Fe for the MOR is 1:2,and the mass activity of Pt_(1)Fe_(2)/C(5.40 A mg_(Pt)^(-1)) is 13.5 times higher than that of conventional commercial Pt/C(Pt/C-JM)(0.40 A mg_(Pt)^(-1)).The introduction of Fe into the Pt lattice forms the PtFe alloy phase,and the electron density of Pt is reduced after forming the PtFe alloy.In-situ Fourier transform infrared results indicate that the addition of oxyphilic metal Fe has reduced the adsorption of reactant molecules on Pt during the MOR.The doping of Fe atoms helps to desorb toxic intermediates and regenerate Pt active sites,promoting the cleavage of C-O bonds with good selectivity of CO_(2)(58.1%).Moreover,the Pt_(1)Fe_(2)/C catalyst exhibits higher CO tolerance,methanol electrooxidation activity,and long-term stability than other Pt_(x)Fe_(y)/C catalysts.

Catalyst光学体表监测在左侧乳腺癌ABC-DIBH放射治疗中的应用

目的 探讨在应用主动呼吸控制(Active Breathing Control,ABC)技术的左侧乳腺癌深吸气屏气(Deep Inspiration Breath Hold,DIBH)放疗中,使用光学体表追踪技术监测屏气的有效性和体位的重复性效果,以保证患者在放疗中吸气方式一致和体位不变,提高放射治疗的精确性。方法 选取应用ABC技术放疗的23例左侧乳腺癌患者为研究对象,以Catalyst进行治疗中DIBH体位监测,以分次内锥形束计算机断层扫描(Cone Beam Computed Tomography,CBCT)为参考标准,分别记录二者误差数据,应用Pearson法和Bland-Altman法分别评估两组误差的相关性和两种系统的一致性。将光学体表监测值与CBCT配准误差值之间的差值定义为Catalyst体表监测精度。结果 Catalyst监测在左右(x轴)方向、头脚(y轴)方向和前后(z轴)方向误差分别为(0.08±1.04)、(1.44±2.15)、(0.45±1.69)mm,CBCT配准误差分别为(0.15±1.15)、(1.51±2.28)、(0.44±1.81)mm。x轴方向和z轴方向相关系数r值分别为0.60、0.77,呈强相关;y轴方向r值为0.82,呈极强相关。二者95%CI值在x、y与z轴方向分别为[-2.01,1.86]、[-2.69,2.57]、[-2.32,2.34] mm,Catalyst监测精度在x、y、z轴方向分别为(-0.08±0.99)、(-0.06±1.34)、(0.01±1.19)mm。结论 Catalyst可有效监测使用ABC进行治疗左侧乳腺癌患者的屏气状态,能准确且实时监测患者位置,提高治疗精确度,具有临床应用价值。

Efficient Direct Decomposition of NO over La_(0.8)A_(0.2)NiO_(3)(A=K, Ba, Y) Catalysts under Microwave Irradiation

La_(0.8)A_(0.2)NiO_(3) (A=K,Ba,Y) catalysts supported on the microwave-absorbing ceramic heating carrier were prepared by the sol-gel method.The crystalline phase and the catalytic activity of the La_(0.8)A_(0.2)NiO_(3)catalysts were characterized by XRD and H_(2) temperature-programmed reduction (TPR).The effects of reaction temperature,oxygen concentration,and gas flow rate on the direct decomposition of nitric oxide over the synthesized catalysts were studied under microwave irradiation (2.45 GHz).The XRD results indicated that the La_(0.8)A_(0.2)NiO_(3) catalysts formed an ABO_(3) perovskite structure,and the H_(2)-TPR results revealed that the relative reducibility of the catalysts increased in the order of La_(0.8)K_(0.2)NiO_(3)>La_(0.8)Ba_(0.2)NiO_(3)>La_(0.8)Y_(0.2)Ni O_(3).Under microwave irradiation,the highest NO conversion amounted to 98.9%,which was obtained with the La_(0.8)K_(0.2)NiO_(3) catalyst at 400℃.The oxygen concentration did not inhibit the NO decomposition on the La_(0.8)A_(0.2)NiO_(3) catalysts,thus the N_(2) selectivity exceeded 99.8%under excess oxygen at 550℃.The NOconversion of the La_(0.8)A_(0.2)NiO_(3) catalysts decreased linearly with the increase in the gas flow rate.

An effective catalyst carrier SiO_(2):Enhancing catalytic and combustion properties of CuFe_(2)O_(4)on energetic components

To enhance the catalytic activity of copper ferrite(CuFe_(2)O_(4))nanoparticle and promote its application as combustion catalyst,a low-cost silicon dioxide(SiO_(2))carrier was employed to construct a novel CuFe_(2)O_(4)/SiO_(2)binary composites via solvothermal method.The phase structure,morphology and catalytic activity of CuFe_(2)O_(4)/SiO_(2)composites were studied firstly,and thermal decomposition,combustion and safety performance of ammonium perchlorate(AP)and 1,3,5-trinitroperhydro-1,3,5-triazine(RDX)with it affecting were then systematically analyzed.The results show that CuFe_(2)O_(4)/SiO_(2)composite can remarkably either advance the decomposition peak temperature of AP and RDX,or reduce the apparent activation energy at their main decomposition zone.Moreover,the flame propagation rate of RDX was promoted by about 2.73 times with SiO_(2)content of 3 wt%,and safety property of energetic component was also improved greatly,in which depressing the electrostatic discharge sensitivity of pure RDX by about 1.89 times.In addition,the effective range of SiO_(2)carrier content in the binary catalyst is found to be 3 to 5 wt%.Therefore,SiO_(2)opens a new insight on the design of combustion catalyst carrier and will promote the application of CuFe_(2)O_(4)catalyst in solid propellant.

100 W-class green hydrogen production from ammonia at a dual-layer electrode containing a Pt-Ir catalyst for an alkaline electrolytic process

Ammonia allows storage and transport of hydrogen over long distances and is an attractive potential hydrogen carrier.Electrochemical decomposition has recently been used for the conversion of ammonia to hydrogen and is regarded as a future technology for production of CO_(2)-free pure hydrogen.Herein,a heterostructural Pt-Ir dual-layer electrode is developed and shown to achieve successful long-term operation in an ammonia electrolyzer with an anion exchange membrane(AEM).This electrolyzer consisted of eight membra ne electrode assemblies(MEAs)with a total geometric area of 200 cm~2 on the anode side,which resulted in a hydrogen production rate of 25 L h~(-1).We observed the degradation in MEA performance attributed to changes in the anode catalyst layer during hydrogen production via ammonia electrolysis.Furthermore,we demonstrated the relationship between the ammonia oxidation reaction(AOR)and the oxygen evolution reaction(OER).

Enhanced stability of nitrogen-doped carbon-supported palladium catalyst for oxidative carbonylation of phenol

Enhancing the stability of supported noble metal catalysts emerges is a major challenge in both science and industry.Herein,a heterogeneous Pd catalyst(Pd/NCF)was prepared by supporting Pd ultrafine metal nanoparticles(NPs)on nitrogen-doped carbon;synthesized by using F127 as a stabilizer,as well as chitosan as a carbon and nitrogen source.The Pd/NCF catalyst was efficient and recyclable for oxidative carbonylation of phenol to diphenyl carbonate,exhibiting higher stability than Pd/NC prepared without F127 addition.The hydrogen bond between chitosan(CTS)and F127 was enhanced by F127,which anchored the N in the free amino group,increasing the N content of the carbon material and ensuring that the support could provide sufficient N sites for the deposition of Pd NPs.This process helped to improve metal dispersion.The increased metal-support interaction,which limits the leaching and coarsening of Pd NPs,improves the stability of the Pd/NCF catalyst.Furthermore,density functional theory calculations indicated that pyridine N stabilized the Pd^(2+)species,significantly inhibiting the loss of Pd^(2+)in Pd/NCF during the reaction process.This work provides a promising avenue towards enhancing the stability of nitrogen-doped carbon-supported metal catalysts.

Realizing methanol synthesis from CO and water via the synergistic effect of Cu^(0)/Cu^(+)over Cu/ZrO_(2) catalyst

The optimizing utilization of ca rbon resources has drawn wide attention all over the world,while exploiting the high-efficiency catalytic routes remains a challenge.Here,a direct methanol synthesis route is realized from pure CO and H_(2)O over 10%Cu/t-ZrO_(2) catalyst,where the time yield of methanol is144.43 mmol mol_(Cu)^(-1)h^(-1)and the methanol selectivity in hydrocarbons is 100%,The Cu species highly dispersed in the t-ZrO_(2) support lead parts of them in the cationic state.The Cu^(+)sites contribute to the dissociation of H_(2)O,providing the H*source for methanol synthesis,while the formed Cu^(0) sites promote the absorption and transfer of H*during the reaction.Moreover,the H_(2)O is even a better H resource than H_(2) due to its better dissociation effectivity in this catalytic system.The present work offers a new approach for methanol synthesis from CO and new insight into the process of supplying H donor.

Preparation of Modified UiO-66 Catalyst and Its Catalytic Performance for NH_(3)-SCR Denitration

Zirconium-based metal-organic framework UiO-66 was successfully prepared by solvothermal method,and UiO-66 was modified by adding regulators such as formic acid,acetic acid,and hydrochloric acid.The NH_(3)-SCR reactivity of the samples was evaluated by the denitration activity evaluation system,and the UiO-66 and the regulator-modified UiO-66 were characterized by XRD,SEM,BET,FTIR,TG,NH_(3)-TPD,etc.,the effects of regulator types on the structure and properties of UiO-66 were investigated.The experimental results show that,after adding the modifier,the morphology of UiO-66 changes from irregular quadrilateral with serious agglomeration to particles with regular crystal shape and good dispersibility,and the crystal morphology of the catalyst is improved.In addition,after adding the modifier,UiO-66 has a larger specific surface area and stronger surface acidity,which optimizes the catalytic performance of UiO-66.The catalytic performance test results of NH_(3)-SCR show that the low-temperature activity of UiO-66 is poor,and it only shows a certain catalytic activity at higher temperatures.The catalytic activity of UiO-66 was significantly improved after adding the regulator.Among them,the UiO-66-HCl modified with hydrochloric acid had the best catalytic activity,and the denitration rate reached 70%when the denitration temperature was 380℃.

Single-atom catalysts for the electrochemical reduction of carbon dioxide into hydrocarbons and oxygenates

The electrochemical reduction of carbon dioxide offers a sound and economically viable technology for the electrification and decarbonization of the chemical and fuel industries.In this technology,an electrocatalytic material and renewable energy-generated electricity drive the conversion of carbon dioxide into high-value chemicals and carbon-neutral fuels.Over the past few years,single-atom catalysts have been intensively studied as they could provide near-unity atom utilization and unique catalytic performance.Single-atom catalysts have become one of the state-of-the-art catalyst materials for the electrochemical reduction of carbon dioxide into carbon monoxide.However,it remains a challenge for single-atom catalysts to facilitate the efficient conversion of carbon dioxide into products beyond carbon monoxide.In this review,we summarize and present important findings and critical insights from studies on the electrochemical carbon dioxide reduction reaction into hydrocarbons and oxygenates using single-atom catalysts.It is hoped that this review gives a thorough recapitulation and analysis of the science behind the catalysis of carbon dioxide into more reduced products through singleatom catalysts so that it can be a guide for future research and development on catalysts with industry-ready performance for the electrochemical reduction of carbon dioxide into high-value chemicals and carbon-neutral fuels.

Boosting Fischer-Tropsch Synthesis via Tuning of N Dopants in TiO_(2)@CN-Supported Ru Catalysts

Nitrogen(N)-doped carbon materials as metal catalyst supports have attracted signifi cant attention,but the eff ect of N dopants on catalytic performance remains unclear,especially for complex reaction processes such as Fischer-Tropsch synthesis(FTS).Herein,we engineered ruthenium(Ru)FTS catalysts supported on N-doped carbon overlayers on TiO_(2)nanoparticles.By regulating the carbonization temperatures,we successfully controlled the types and contents of N dopants to identify their impacts on metal-support interactions(MSI).Our fi ndings revealed that N dopants establish a favorable surface environment for electron transfer from the support to the Ru species.Moreover,pyridinic N demonstrates the highest electron-donating ability,followed by pyrrolic N and graphitic N.In addition to realizing excellent catalytic stability,strengthening the interaction between Ru sites and N dopants increases the Ru^(0)/Ru^(δ+)ratios to enlarge the active site numbers and surface electron density of Ru species to enhance the strength of adsorbed CO.Consequently,it improves the catalyst’s overall performance,encompassing intrinsic and apparent activities,as well as its ability for carbon chain growth.Accordingly,the as-synthesized Ru/TiO_(2)@CN-700 catalyst with abundant pyridine N dopants exhibits a superhigh C_(5+)time yield of 219.4 mol CO/(mol Ru·h)and C_(5+)selectivity of 85.5%.