In this research, the changing rules of billet forged Ti-22 Al-24 Nb alloy with various solution time were studied, and the mechanical properties of different microstructure were tested at the room temperature. The re...In this research, the changing rules of billet forged Ti-22 Al-24 Nb alloy with various solution time were studied, and the mechanical properties of different microstructure were tested at the room temperature. The results indicate that the(α2+O+B2) three-phase microstructure with equiaxed grains was acquired by Ti-22 Al-24 Nb alloy billet forging, and the average size of the grains was about 300 μm. With the increase of solution time, the primary lath-shaped O phase began to dissolve, and then the equiaxial α2 phase started to dissolve, but the undissolved α2/O phase began to be equiaxial and grow. The grains of original B2 phase recrystallized and grew. After the 2 h solution treatment, the recrystallization of grains was completed basically and the average size of the grains was about 100 μm. After the 2.5 h solution treatment, the strength of the alloy decreased, and the plasticity increased. However, when the solution treatment increased to 3 h, the plasticity decreased but the strength increased. The optimal solution parameters of Ti-22 Al-24 Nb alloy were the holding time of 2 h, the solution temperature of 1 000 ?C, and water cooling. Excellent comprehensive mechanical properties can be accquired under these parameters. The tensile strength, the yield strength, the elasticity modulus, the elongation, and the section shrinkage were 950 MPa, 915 MPa, 90 GPa, 15.69% and 42.28%, respectively.展开更多
The phase transformation and microstructure in Ti-22Al-25Nb alloy are extremely complex.In this work,the morphology evolution of the O phase during the heating and cooling process was investigated by electron backscat...The phase transformation and microstructure in Ti-22Al-25Nb alloy are extremely complex.In this work,the morphology evolution of the O phase during the heating and cooling process was investigated by electron backscatter diffraction(EBSD)and first-principles calculations.The results show that the O→α_(2)phase transformation process during the heating process is as follows:spheroidization of the O phase occurs first,then theα_(2)phase nucleates in the spheroidized O phase,grows and replaces the O phase,completing the O→α_(2)phase transformation.In the meanwhile,the diffusion of Nb from Nb-poor O to Nb-rich B2 phases is a back-diffusion process.According to first-principles calculations,the driving force of the O→α_(2)phase transformation is the difference in the free energies of formation for the two phases(0.09 eV/atom).When the Nb content is greater than 15.625%,the lattice distortion of theα_(2)phase sharply increases,and the distortion energy drives the back-diffusion of Nb.During the cooling process,theα_(2)→O phase transformation is difficult and slow due to the difficult diffusion of Nb from the B2 toα_(2)phases.When holding for 60 min at 960℃,the coarseα_(2)phase gradually transforms to the O phase from the margin to the inside,forming a dispersed mixed structure of the O andα_(2)phases.During the B2→O transformation,the nucleation of the O phase induces a high stress region,in the range of approximately 200 nm.展开更多
Vacuum brazing was successfully used to join Ti-22Al-25Nb alloy using Ti-Ni-Nb brazing alloys prepared by arc-melting. The influence of Nb content in the Ti-Ni-Nb brazing alloys on the interfacial microstructure and m...Vacuum brazing was successfully used to join Ti-22Al-25Nb alloy using Ti-Ni-Nb brazing alloys prepared by arc-melting. The influence of Nb content in the Ti-Ni-Nb brazing alloys on the interfacial microstructure and mechanical properties of the brazed joints was investigated. The results showed that the interfacial microstructure of brazed joint consisted of B2, O, ？3, and Ti2 Ni phase, while the width of brazing seams varied at different Nb contents. The room temperature shear strength reached359 MPa when the joints were brazed with eutectic Ti40Ni40Nb20 alloy at 1180？C for 20 min, and it was321, 308 and 256 MPa at 500, 650 and 800？C, respectively. Cracks primarily initiated and propagated in ？3compounds, and partially traversed B2＋O region. Moreover, the fracture surface displayed typical ductile dimples when cracks propagated through B2＋O region, which was favorable for the mechanical properties of the brazed joint.展开更多
基金Funded by the National Natural Science Foundation of China(No.51464035)
文摘In this research, the changing rules of billet forged Ti-22 Al-24 Nb alloy with various solution time were studied, and the mechanical properties of different microstructure were tested at the room temperature. The results indicate that the(α2+O+B2) three-phase microstructure with equiaxed grains was acquired by Ti-22 Al-24 Nb alloy billet forging, and the average size of the grains was about 300 μm. With the increase of solution time, the primary lath-shaped O phase began to dissolve, and then the equiaxial α2 phase started to dissolve, but the undissolved α2/O phase began to be equiaxial and grow. The grains of original B2 phase recrystallized and grew. After the 2 h solution treatment, the recrystallization of grains was completed basically and the average size of the grains was about 100 μm. After the 2.5 h solution treatment, the strength of the alloy decreased, and the plasticity increased. However, when the solution treatment increased to 3 h, the plasticity decreased but the strength increased. The optimal solution parameters of Ti-22 Al-24 Nb alloy were the holding time of 2 h, the solution temperature of 1 000 ?C, and water cooling. Excellent comprehensive mechanical properties can be accquired under these parameters. The tensile strength, the yield strength, the elasticity modulus, the elongation, and the section shrinkage were 950 MPa, 915 MPa, 90 GPa, 15.69% and 42.28%, respectively.
基金the financial support from the National Natural Science Foundation of China under Grant No.52005129。
文摘The phase transformation and microstructure in Ti-22Al-25Nb alloy are extremely complex.In this work,the morphology evolution of the O phase during the heating and cooling process was investigated by electron backscatter diffraction(EBSD)and first-principles calculations.The results show that the O→α_(2)phase transformation process during the heating process is as follows:spheroidization of the O phase occurs first,then theα_(2)phase nucleates in the spheroidized O phase,grows and replaces the O phase,completing the O→α_(2)phase transformation.In the meanwhile,the diffusion of Nb from Nb-poor O to Nb-rich B2 phases is a back-diffusion process.According to first-principles calculations,the driving force of the O→α_(2)phase transformation is the difference in the free energies of formation for the two phases(0.09 eV/atom).When the Nb content is greater than 15.625%,the lattice distortion of theα_(2)phase sharply increases,and the distortion energy drives the back-diffusion of Nb.During the cooling process,theα_(2)→O phase transformation is difficult and slow due to the difficult diffusion of Nb from the B2 toα_(2)phases.When holding for 60 min at 960℃,the coarseα_(2)phase gradually transforms to the O phase from the margin to the inside,forming a dispersed mixed structure of the O andα_(2)phases.During the B2→O transformation,the nucleation of the O phase induces a high stress region,in the range of approximately 200 nm.
基金supported by the National Natural Science Foundation of China (Grant No. 51574177)the China Natural Founds for Distinguished Young Scientists (Grant No. 51325401)the National High Technology Research and Development Program of China (“863” Program, Granted No. 2015AA042504)
文摘Vacuum brazing was successfully used to join Ti-22Al-25Nb alloy using Ti-Ni-Nb brazing alloys prepared by arc-melting. The influence of Nb content in the Ti-Ni-Nb brazing alloys on the interfacial microstructure and mechanical properties of the brazed joints was investigated. The results showed that the interfacial microstructure of brazed joint consisted of B2, O, ？3, and Ti2 Ni phase, while the width of brazing seams varied at different Nb contents. The room temperature shear strength reached359 MPa when the joints were brazed with eutectic Ti40Ni40Nb20 alloy at 1180？C for 20 min, and it was321, 308 and 256 MPa at 500, 650 and 800？C, respectively. Cracks primarily initiated and propagated in ？3compounds, and partially traversed B2＋O region. Moreover, the fracture surface displayed typical ductile dimples when cracks propagated through B2＋O region, which was favorable for the mechanical properties of the brazed joint.
