The hot corrosion behaviour of a modified Ti3Al-based alloy under thin Na2SO4deposit film was investigated at910and950°C in air.The corrosion product was identified by XRD and its morphologies on the surface and ...The hot corrosion behaviour of a modified Ti3Al-based alloy under thin Na2SO4deposit film was investigated at910and950°C in air.The corrosion product was identified by XRD and its morphologies on the surface and cross-section were observed bySEM.The alloy suffered from considerable hot corrosion attack.The mass gain versus time curves obtained by TGA exhibited tworegions of different kinetics.The whole corroded layer consisted of loose and porous mixture oxides of TiO2,Nb2O5and Al2O3.Numerous small nodules of corrosion product were observed.An illustrative schematic was established to describe the formationprocess of such nodules.It seemed that the refractory oxides played a significantly important role in determining the development ofhot corrosion attack.展开更多
The effect of hot-rolling processing on microstructure as well as the relationship between the elongated grain structure and tensile properties are investigated. The results indicate that the elongated grain structure...The effect of hot-rolling processing on microstructure as well as the relationship between the elongated grain structure and tensile properties are investigated. The results indicate that the elongated grain structure influences the tensile properties and creep rupture life of Fe3Al alloy significantly. For the better strength and ductility at RT,a thinner elongated grain structure is desirable. When the elongated grain size is increased, the tensile properties will be decreased. On the other hand, the creeP rupture life at 600℃ is increased with the increase of elongated grain size.展开更多
In the present paper, the relations between the microstructure and the properties of Ti-14Al-21Nb and Ti-14Al-20Nb-3.5V-2Mo alloys at different temperatures and different cooling rates of heat treatment were re-vealed...In the present paper, the relations between the microstructure and the properties of Ti-14Al-21Nb and Ti-14Al-20Nb-3.5V-2Mo alloys at different temperatures and different cooling rates of heat treatment were re-vealed by X-ray , optical microscope , HVTEM , auto-graphical-analyser and mechanical properties test at roomand high temperature. The experimental results show as follows: at 1040～1120℃ 14h WQ, the microstruc-ture of Ti-14Al-21Nb bar is primary phaseα_2+B2. With temperature increasing, the primary α_2 phase de-crease and the mechanical properties ultimate tensile strength (UTS), yield strength (YS) and elongation(EL) at room temperature increase. When it has reduced the α_2 phase by 50% (at 1080℃/4h WQ) , the me-chanical properties at room temperature are excellent , EL being 10. 5%. Following the α_2 phase reduces contin-uously , UTS, YS are going up, but EL is going down. After heated at two phases range and cooled down tothe room temperature with furnace, the microstructure of Ti-14Al-20Nb-3.5V-2Mo alloy is the equiaxed α_2+needle-like α_2+βphase. The mechanical properties at room temperature and 700℃ are fairly good.展开更多
The Proccss of gascous hydrogcn charging into a Ti_3Al- based alloy in the temperature range of 500-650℃isinvcstigatcd. The rcsnlls snoxvc that in rclatiollshil, between the average hydrogen concentration at constant...The Proccss of gascous hydrogcn charging into a Ti_3Al- based alloy in the temperature range of 500-650℃isinvcstigatcd. The rcsnlls snoxvc that in rclatiollshil, between the average hydrogen concentration at constant tempreature and charging time reveals a parabolie rate law Applying the theory of lattice constant tcnlpcralurc and hrgillg tin rcvcals a parabolic riltc laiv. Applyillg tbcthcoly oftatticc dillbsio to allalyzc the hydrogcll diethesioll they andthat cncrgy of hydrogcn diffusion is 90.40 kJ/mol. and the equilibrium hydrogen content in the alloy depends on the temperature of the gaseous hydrogen charging process展开更多
The phase field method was applied to study the microstructure evolution of Ni4Ti3 precipitates during stress-free and stress-assisted aging of bi-crystalline NiTi shape memory alloys （SAMs） with two different initi...The phase field method was applied to study the microstructure evolution of Ni4Ti3 precipitates during stress-free and stress-assisted aging of bi-crystalline NiTi shape memory alloys （SAMs） with two different initial Ni-contents of 51.5% and 52.5% （mole fraction）, respectively. The simulation results show that, during stress-free aging of the NiTi alloy with a low supersaturation of Ni （i.e., Ti-51.5%Ni）, the Ni4Ti3 precipitates exhibit a heterogeneous distribution with a high number density of particles at the grain boundary, leaving most of the grain interiors free of precipitates; while for the NiTi alloy with a high supersaturation of Ni （i.e., Ti-52.5%Ni）, the Ni4Ti3 precipitates show a homogeneous distribution across the entire simulation system. The stress-assisted aging can give rise to homogeneous distribution of the precipitates, regardless of the initial Ni-content; however, the distribution of variant type within the two grains is heterogeneous.展开更多
The Cu-Ti-Si alloys containing in-situ formed Ti5Si3 are prepared. In order to clarify the Ti5Si3 formation processes and its microstructure characteristics, the as-cast and deeply etched Cu-Ti-Si alloys with differen...The Cu-Ti-Si alloys containing in-situ formed Ti5Si3 are prepared. In order to clarify the Ti5Si3 formation processes and its microstructure characteristics, the as-cast and deeply etched Cu-Ti-Si alloys with different compositions and cooling rates were investigated using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). It is found that the eutectic Ti5Si3 phases in Cu-Ti-Si alloys are rod-like with hexagonal cross section which tend to intertwine with each other to form a firm skeleton like a bird nest structure which can make the alloys keep their original shape even after etching off the Cu matrix. In addition, there is Cu in the center of many Ti5Si3 rods, resulting in a core-shell structure. With the increase of the cooling rate, Ti5Si3 distributes more uniformly, and the diameter of Ti5Si3 significantly decreases, with a minimum size of less than 100 nm, while the aspect ratio of Ti5Si3 increases.展开更多
The key to managing fracture is to achieve stable internal fixation,and currently,biologically and mechanically appropriate internal fixation devices are urgently needed.With excellent biocompatibility and corrosion r...The key to managing fracture is to achieve stable internal fixation,and currently,biologically and mechanically appropriate internal fixation devices are urgently needed.With excellent biocompatibility and corrosion resistance,titanium–niobium alloys have the potential to become a new generation of internal fixation materials for fractures.However,the role and mechanism of titanium–niobium alloys on promoting fracture healing are still undefined.Therefore,in this study,we systematically evaluated the bone-enabling properties of Ti45Nb via in vivo and in vitro experiments.In vitro,we found that Ti45Nb has an excellent ability to promote MC3T3-E1 cell adhesion and proliferation without obvious cytotoxicity.Alkaline phosphatase(ALP)activity and alizarin red staining and semiquantitative analysis showed that Ti45Nb enhanced the osteogenic differentiation of MC3T3-E1 cells compared to the Ti6Al4V control.In the polymerase chain reaction experiment,the expression of osteogenic genes in the Ti45Nb group,such as ALP,osteopontin(OPN),osteocalcin(OCN),type 1 collagen(Col-1)and runt-related transcription factor-2(Runx2),was significantly higher than that in the control group.Meanwhile,in the western blot experiment,the expression of osteogenic-related proteins in the Ti45Nb group was significantly increased,and the expression of PI3K–Akt-related proteins was also higher,which indicated that Ti45Nb might promote fracture healing by activating the PI3K–Akt signaling pathway.In vivo,we found that Ti45Nb implants accelerated fracture healing compared to Ti6Al4V,and the biosafety of Ti45Nb was confirmed by histological evaluation.Furthermore,immunohistochemical staining confirmed that Ti45Nb may promote osteogenesis by upregulating the PI3K/Akt signaling pathway.Our study demonstrated that Ti45Nb exerts an excellent ability to promote fracture healing as well as enhance osteoblast differentiation by activating the PI3K/Akt signaling pathway,and its good biosafety has been confirmed,which indicates its clinical translation potential.展开更多
Based on the alloy Cu55Ni45 (at pct), holding the proportion of Cu to Ni in constant and in the temperature range of 1233~1573 K, the wetting angles of CuNi-0~56 at pct Ti alloys on Si3N4 have been measured by the ses...Based on the alloy Cu55Ni45 (at pct), holding the proportion of Cu to Ni in constant and in the temperature range of 1233~1573 K, the wetting angles of CuNi-0~56 at pct Ti alloys on Si3N4 have been measured by the sessile drop method. With the increase of Ti content, the wetting angles decreased. The equilibrium wetting angle was 5° when Ti content ≥32 at pct.In the case of same Ti content, the activity of Ti in CuNiTi alloy was weaker than that in CuTi alloy The cross-section of the CuNiTi-Si3N4 interface and the elements distribution were examined by scanning electron microscope with X-ray wave-dispersion spectrometer, and the reaction products formed at the interface were determined by X-ray diffiaction analysis method.展开更多
The phase transformation and deformation mechanism of the alloy based on composition Ti_3Al with addition of Nb,V,Mo have been studied by use of transmission electron microscopy (TEM).It has been shown that the orient...The phase transformation and deformation mechanism of the alloy based on composition Ti_3Al with addition of Nb,V,Mo have been studied by use of transmission electron microscopy (TEM).It has been shown that the orientation relationship of α_2 phase transformed from β phase is:(0001)α_2// (l10)β,[1210]α_2//[111]β.The present dislocation slip systems in α_2 phase are (1100)[0001] and (1100)<1120>.There also exist α_2 twins which have new twin relationship and the twin plane is (2021).展开更多
On the basis of the framework of systematic science of alloys （SSA）, the basic information such as states, volumes, and potential energies of characteristic atoms in hcp Ti-Al system have been determined. The averag...On the basis of the framework of systematic science of alloys （SSA）, the basic information such as states, volumes, and potential energies of characteristic atoms in hcp Ti-Al system have been determined. The average atomic state of the hcp Ti3Al compound consisting of ψ4^Ti and ψ0^Al atoms is 0.75[Ar] （3dn）^0.573 （3dc）^2.1685 （4sc）^0.972 （4sf）^0.3093 ＋ 0.25[Ne] （3sc）^1.32 （3pc）^1.19 （3sf ＋ 3pf）^0.49. The brittleness of the ordered hcp Ti3Al compound has been discussed considering the fundamental factors, which are atomic states, bond networks, potential energy wave planes, and the ratio xTi/xAl. The existence of more pc and more dc directional electrons in the hcp Ti3Al compound lead to considerable brittleness; From bond networks and potential energy wave planes, the hcp Ti3Al compound has poorer ductility than the pure hcp Ti metal and the pure fcc Al metal; The Al-rich hcp Ti3Al ordered type alloys have poorer ductility than the Ti-rich hcp Ti3Al ordered type alloys.展开更多
To explore the approaches of combined toughening and strengthening of the Al_3Ti-based L1_2 intermetallic alloys, multiphase Al_3Ti alloys formed by combining with reinforcement or by second phase precipitation are be...To explore the approaches of combined toughening and strengthening of the Al_3Ti-based L1_2 intermetallic alloys, multiphase Al_3Ti alloys formed by combining with reinforcement or by second phase precipitation are being studied. The interface reactions between Al_(66)Fe_9Ti_(25)matrix and SiC reinforcement were investigated. It is determined that SiC is chemically incompatible with the Al_(66)Fe_9Ti_(25)matrix, Al_2O_3 barrier coating on SiC by sol-gel process was developed to minimize the interfacial reactions. On the other hand, a new type of Al_3Ti-based alloy having a L1_2 matrix with second phase precipitation has been developed. The quaternary alloys based on Al_(66)Fe_9Ti_(25)and modified with Nb additions, consist of a L1_2 matrix and D0_(22) second phase in the annealed state ,but the second phase can be dissolved by solution treatment and precipitated during high temperature aging.展开更多
A Y2O3 particle enhanced Ni/TiC composite coating was fabricated in-situ on a TC4 Ti alloy by laser surface cladding. The phase component, microstructure, composition distribution and properties of the composite layer...A Y2O3 particle enhanced Ni/TiC composite coating was fabricated in-situ on a TC4 Ti alloy by laser surface cladding. The phase component, microstructure, composition distribution and properties of the composite layer were investigated. The composite layer has graded microstructures and compositions, due to the fast melting followed by rapid solidification and cooling during laser cladding. The TiC powders are completely dissolved into the melted layer during melting and segregated as fine dendrites when solidified. The size of TiC dendrites decreases with increasing depth. Y2O3 fine particles distribute in the whole clad layer. The Y2O3 particle enhanced Ni/TiC composite layer has a quite uniform hardness along depth with a maximum value of HV1380, which is 4 times higher than the initial hardness. The wear resistance of the Ti alloy is significantly improved after laser cladding due to the high hardness of the composite coating.展开更多
A Ti(Al,Si)3 diffusion coating was prepared on γ-TiAl alloy by cold sprayed Al?20Si alloy coating, followed by a heat-treatment. The isothermal and cyclic oxidation tests were conducted at 900 °C for 1000 h and ...A Ti(Al,Si)3 diffusion coating was prepared on γ-TiAl alloy by cold sprayed Al?20Si alloy coating, followed by a heat-treatment. The isothermal and cyclic oxidation tests were conducted at 900 °C for 1000 h and 120 cycles to check the oxidation resistance of the coating. The microstructure and phase transformation of the coating before and after the oxidation were studied by SEM, XRD and EPMA. The results indicate that the diffusion coating shows good oxidation resistance. The mass gain of the diffusion coating is only a quarter of that of bare alloy. After oxidation, the diffusion coating is degraded into three layers: an inner TiAl2 layer, a two-phase intermediate layer composed of a Ti(Al,Si)3 matrix and Si-rich precipitates, and a porous layer because of the inter-diffusion between the coating and substrate.展开更多
基金Projects(51271191,51571205)supported by the National Natural Science Foundation of China
文摘The hot corrosion behaviour of a modified Ti3Al-based alloy under thin Na2SO4deposit film was investigated at910and950°C in air.The corrosion product was identified by XRD and its morphologies on the surface and cross-section were observed bySEM.The alloy suffered from considerable hot corrosion attack.The mass gain versus time curves obtained by TGA exhibited tworegions of different kinetics.The whole corroded layer consisted of loose and porous mixture oxides of TiO2,Nb2O5and Al2O3.Numerous small nodules of corrosion product were observed.An illustrative schematic was established to describe the formationprocess of such nodules.It seemed that the refractory oxides played a significantly important role in determining the development ofhot corrosion attack.
文摘The effect of hot-rolling processing on microstructure as well as the relationship between the elongated grain structure and tensile properties are investigated. The results indicate that the elongated grain structure influences the tensile properties and creep rupture life of Fe3Al alloy significantly. For the better strength and ductility at RT,a thinner elongated grain structure is desirable. When the elongated grain size is increased, the tensile properties will be decreased. On the other hand, the creeP rupture life at 600℃ is increased with the increase of elongated grain size.
文摘In the present paper, the relations between the microstructure and the properties of Ti-14Al-21Nb and Ti-14Al-20Nb-3.5V-2Mo alloys at different temperatures and different cooling rates of heat treatment were re-vealed by X-ray , optical microscope , HVTEM , auto-graphical-analyser and mechanical properties test at roomand high temperature. The experimental results show as follows: at 1040～1120℃ 14h WQ, the microstruc-ture of Ti-14Al-21Nb bar is primary phaseα_2+B2. With temperature increasing, the primary α_2 phase de-crease and the mechanical properties ultimate tensile strength (UTS), yield strength (YS) and elongation(EL) at room temperature increase. When it has reduced the α_2 phase by 50% (at 1080℃/4h WQ) , the me-chanical properties at room temperature are excellent , EL being 10. 5%. Following the α_2 phase reduces contin-uously , UTS, YS are going up, but EL is going down. After heated at two phases range and cooled down tothe room temperature with furnace, the microstructure of Ti-14Al-20Nb-3.5V-2Mo alloy is the equiaxed α_2+needle-like α_2+βphase. The mechanical properties at room temperature and 700℃ are fairly good.
文摘The Proccss of gascous hydrogcn charging into a Ti_3Al- based alloy in the temperature range of 500-650℃isinvcstigatcd. The rcsnlls snoxvc that in rclatiollshil, between the average hydrogen concentration at constant tempreature and charging time reveals a parabolie rate law Applying the theory of lattice constant tcnlpcralurc and hrgillg tin rcvcals a parabolic riltc laiv. Applyillg tbcthcoly oftatticc dillbsio to allalyzc the hydrogcll diethesioll they andthat cncrgy of hydrogcn diffusion is 90.40 kJ/mol. and the equilibrium hydrogen content in the alloy depends on the temperature of the gaseous hydrogen charging process
基金Project (50871039) supported by the National Natural Science Foundation of ChinaProject (2011ZB0007) supported by the Fundamental Research Funds for Central Universities of ChinaProject (201104090881) support by China Postdoctoral Science Foundation
文摘The phase field method was applied to study the microstructure evolution of Ni4Ti3 precipitates during stress-free and stress-assisted aging of bi-crystalline NiTi shape memory alloys （SAMs） with two different initial Ni-contents of 51.5% and 52.5% （mole fraction）, respectively. The simulation results show that, during stress-free aging of the NiTi alloy with a low supersaturation of Ni （i.e., Ti-51.5%Ni）, the Ni4Ti3 precipitates exhibit a heterogeneous distribution with a high number density of particles at the grain boundary, leaving most of the grain interiors free of precipitates; while for the NiTi alloy with a high supersaturation of Ni （i.e., Ti-52.5%Ni）, the Ni4Ti3 precipitates show a homogeneous distribution across the entire simulation system. The stress-assisted aging can give rise to homogeneous distribution of the precipitates, regardless of the initial Ni-content; however, the distribution of variant type within the two grains is heterogeneous.
基金This work was financially supported by the Natural Science Foundation of Hebei Province of China(Grant No.E2019502057)the Fundamental Research Funds for the Central Universities,China(Grant No.2018MS120).
文摘The Cu-Ti-Si alloys containing in-situ formed Ti5Si3 are prepared. In order to clarify the Ti5Si3 formation processes and its microstructure characteristics, the as-cast and deeply etched Cu-Ti-Si alloys with different compositions and cooling rates were investigated using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). It is found that the eutectic Ti5Si3 phases in Cu-Ti-Si alloys are rod-like with hexagonal cross section which tend to intertwine with each other to form a firm skeleton like a bird nest structure which can make the alloys keep their original shape even after etching off the Cu matrix. In addition, there is Cu in the center of many Ti5Si3 rods, resulting in a core-shell structure. With the increase of the cooling rate, Ti5Si3 distributes more uniformly, and the diameter of Ti5Si3 significantly decreases, with a minimum size of less than 100 nm, while the aspect ratio of Ti5Si3 increases.
基金This work was supported by the National Natural Science Foundation of China(Nos.81972058,81902194 and 82202680)the Science and Technology Commission of Shanghai Municipality(No.22YF1422900)+3 种基金the Shanghai Municipal Key Clinical Specialty,China(No.shslczdzk06701)the National Facility for Translational Medicine(Shanghai),China(No.TMSZ-2020-207)the Shanghai Engineering Research Center of Orthopedic Innovative Instruments and Personalized Medicine Instruments and Personalized Medicine(No.19DZ2250200)the Key R&D Program of Ningxia,China(Nos.2020BCH01001 and 2021BEG02037).
文摘The key to managing fracture is to achieve stable internal fixation,and currently,biologically and mechanically appropriate internal fixation devices are urgently needed.With excellent biocompatibility and corrosion resistance,titanium–niobium alloys have the potential to become a new generation of internal fixation materials for fractures.However,the role and mechanism of titanium–niobium alloys on promoting fracture healing are still undefined.Therefore,in this study,we systematically evaluated the bone-enabling properties of Ti45Nb via in vivo and in vitro experiments.In vitro,we found that Ti45Nb has an excellent ability to promote MC3T3-E1 cell adhesion and proliferation without obvious cytotoxicity.Alkaline phosphatase(ALP)activity and alizarin red staining and semiquantitative analysis showed that Ti45Nb enhanced the osteogenic differentiation of MC3T3-E1 cells compared to the Ti6Al4V control.In the polymerase chain reaction experiment,the expression of osteogenic genes in the Ti45Nb group,such as ALP,osteopontin(OPN),osteocalcin(OCN),type 1 collagen(Col-1)and runt-related transcription factor-2(Runx2),was significantly higher than that in the control group.Meanwhile,in the western blot experiment,the expression of osteogenic-related proteins in the Ti45Nb group was significantly increased,and the expression of PI3K–Akt-related proteins was also higher,which indicated that Ti45Nb might promote fracture healing by activating the PI3K–Akt signaling pathway.In vivo,we found that Ti45Nb implants accelerated fracture healing compared to Ti6Al4V,and the biosafety of Ti45Nb was confirmed by histological evaluation.Furthermore,immunohistochemical staining confirmed that Ti45Nb may promote osteogenesis by upregulating the PI3K/Akt signaling pathway.Our study demonstrated that Ti45Nb exerts an excellent ability to promote fracture healing as well as enhance osteoblast differentiation by activating the PI3K/Akt signaling pathway,and its good biosafety has been confirmed,which indicates its clinical translation potential.
文摘Based on the alloy Cu55Ni45 (at pct), holding the proportion of Cu to Ni in constant and in the temperature range of 1233~1573 K, the wetting angles of CuNi-0~56 at pct Ti alloys on Si3N4 have been measured by the sessile drop method. With the increase of Ti content, the wetting angles decreased. The equilibrium wetting angle was 5° when Ti content ≥32 at pct.In the case of same Ti content, the activity of Ti in CuNiTi alloy was weaker than that in CuTi alloy The cross-section of the CuNiTi-Si3N4 interface and the elements distribution were examined by scanning electron microscope with X-ray wave-dispersion spectrometer, and the reaction products formed at the interface were determined by X-ray diffiaction analysis method.
文摘The phase transformation and deformation mechanism of the alloy based on composition Ti_3Al with addition of Nb,V,Mo have been studied by use of transmission electron microscopy (TEM).It has been shown that the orientation relationship of α_2 phase transformed from β phase is:(0001)α_2// (l10)β,[1210]α_2//[111]β.The present dislocation slip systems in α_2 phase are (1100)[0001] and (1100)<1120>.There also exist α_2 twins which have new twin relationship and the twin plane is (2021).
文摘On the basis of the framework of systematic science of alloys （SSA）, the basic information such as states, volumes, and potential energies of characteristic atoms in hcp Ti-Al system have been determined. The average atomic state of the hcp Ti3Al compound consisting of ψ4^Ti and ψ0^Al atoms is 0.75[Ar] （3dn）^0.573 （3dc）^2.1685 （4sc）^0.972 （4sf）^0.3093 ＋ 0.25[Ne] （3sc）^1.32 （3pc）^1.19 （3sf ＋ 3pf）^0.49. The brittleness of the ordered hcp Ti3Al compound has been discussed considering the fundamental factors, which are atomic states, bond networks, potential energy wave planes, and the ratio xTi/xAl. The existence of more pc and more dc directional electrons in the hcp Ti3Al compound lead to considerable brittleness; From bond networks and potential energy wave planes, the hcp Ti3Al compound has poorer ductility than the pure hcp Ti metal and the pure fcc Al metal; The Al-rich hcp Ti3Al ordered type alloys have poorer ductility than the Ti-rich hcp Ti3Al ordered type alloys.
文摘To explore the approaches of combined toughening and strengthening of the Al_3Ti-based L1_2 intermetallic alloys, multiphase Al_3Ti alloys formed by combining with reinforcement or by second phase precipitation are being studied. The interface reactions between Al_(66)Fe_9Ti_(25)matrix and SiC reinforcement were investigated. It is determined that SiC is chemically incompatible with the Al_(66)Fe_9Ti_(25)matrix, Al_2O_3 barrier coating on SiC by sol-gel process was developed to minimize the interfacial reactions. On the other hand, a new type of Al_3Ti-based alloy having a L1_2 matrix with second phase precipitation has been developed. The quaternary alloys based on Al_(66)Fe_9Ti_(25)and modified with Nb additions, consist of a L1_2 matrix and D0_(22) second phase in the annealed state ,but the second phase can be dissolved by solution treatment and precipitated during high temperature aging.
基金Projects (51101096, 51002093) supported by the National Natural Science Foundation of ChinaProject (1052nm05000) supported by Special Foundation of the Shanghai Science and Technology Commission for Nano-Materials ResearchProject (J51042) supported by Leading Academic Discipline Project of the Shanghai Education Commission, China
文摘A Y2O3 particle enhanced Ni/TiC composite coating was fabricated in-situ on a TC4 Ti alloy by laser surface cladding. The phase component, microstructure, composition distribution and properties of the composite layer were investigated. The composite layer has graded microstructures and compositions, due to the fast melting followed by rapid solidification and cooling during laser cladding. The TiC powders are completely dissolved into the melted layer during melting and segregated as fine dendrites when solidified. The size of TiC dendrites decreases with increasing depth. Y2O3 fine particles distribute in the whole clad layer. The Y2O3 particle enhanced Ni/TiC composite layer has a quite uniform hardness along depth with a maximum value of HV1380, which is 4 times higher than the initial hardness. The wear resistance of the Ti alloy is significantly improved after laser cladding due to the high hardness of the composite coating.
基金Project(50971127)supported by the National Natural Science Foundation of China
文摘A Ti(Al,Si)3 diffusion coating was prepared on γ-TiAl alloy by cold sprayed Al?20Si alloy coating, followed by a heat-treatment. The isothermal and cyclic oxidation tests were conducted at 900 °C for 1000 h and 120 cycles to check the oxidation resistance of the coating. The microstructure and phase transformation of the coating before and after the oxidation were studied by SEM, XRD and EPMA. The results indicate that the diffusion coating shows good oxidation resistance. The mass gain of the diffusion coating is only a quarter of that of bare alloy. After oxidation, the diffusion coating is degraded into three layers: an inner TiAl2 layer, a two-phase intermediate layer composed of a Ti(Al,Si)3 matrix and Si-rich precipitates, and a porous layer because of the inter-diffusion between the coating and substrate.
