This article describes the properties of TiO_2-siloxane that can be appliedto spacecraft polymers to protect from AO environmental influences on the life and performance ofspace mission. This protective coating is obt...This article describes the properties of TiO_2-siloxane that can be appliedto spacecraft polymers to protect from AO environmental influences on the life and performance ofspace mission. This protective coating is obtained by mixing TiO_2, siloxane and silicate mineralsvia dispersion and ground. Kaptons with and without TiO_2-siloxane overcoating are exposed to AOimpingement from ground-simulation laboratory. Fourier transform infrared spectroscopy (FTIR) ,LAMBDA-9 spectrophotometer, X-ray photoelectron spectroscopy (XPS) and scanning electronmicroscopy(SEM) are used to characterize the chemical and physical changes on the surfaces of theunprotected Kapton and protected Kapton samples . The application of protective coatings and theirresistance to the space environment are described for ground-based test. From the test results itcan be seen that Kapton is heavily eroded, while there is little change on surface ofTiO_2-siloxane. So it can be concluded that TiO_2-siloxane coatings are highly resistant to AO andthat it is a kind of protective coating for Kapton.展开更多
The high activity of metallic magnesium and alloys limits its potential in biomedical applications;in recent years,extensive efforts have been devoted to modulating this reactivity.In this work,we present Mg(OH)_(2) a...The high activity of metallic magnesium and alloys limits its potential in biomedical applications;in recent years,extensive efforts have been devoted to modulating this reactivity.In this work,we present Mg(OH)_(2) and TiO_(2)barrier coatings to reduce the degradation of magnesium alloy(Mg-Ca-Zn)surfaces.These coatings were deposited by the anodization method and the spin-coating technique,respectively.The anodized layer was coated with TiO_(2)generated from the hydrolysis of 3%weight of TTIP(Ti[OCH(CH_(3))_(2)]_(4),Titanium(IV)isopropoxide)in 2-Propanol deposited by the spin-coating method.Studying the degradation in Ringer’s solution by electrochemical impedance spectroscopy and OCP revealed a 98%reduction in pittings in uncoated samples after 14 days of immersion.The p H measurements revealed that the TiO_(2)coating reduced the alkalization of the physiological environment,keeping the pH at 6.0 values.In vitro studies of two types of bacteria(E.coli and S.aureus)exhibited zones of inhibition in the agar and activity bactericidal(kill time test).The mechanisms behind the improved degradation resistance and enhanced antibacterial activity are presented and discussed here.Surface modification with Mg(OH)_(2)/TiO_(2)coatings is a promising strategy to control the biodegradation of magnesium implants for bone regeneration.展开更多
The effects of welding current on the macro-morphology, microstructure and mechanical properties of tungsten inert gas(TIG) welded AZ31 magnesium alloy joints with TiO2 coating were investigated. The results showed th...The effects of welding current on the macro-morphology, microstructure and mechanical properties of tungsten inert gas(TIG) welded AZ31 magnesium alloy joints with TiO2 coating were investigated. The results showed that the increase of welding current led to the increase in the depth/width ratio and deteriorated the surface appearance of the welded seams with TiO2 coating. The grain size of α-Mg and the amount of granular β-Mg17Al12 particles in the welded seams also increased. The welded joints with TiO2 coating exhibited a deeper weld penetration and larger grain size compared with the welded joint without TiO2 coating. When the welding current was less than 130 A, the ultimate tensile strength of the welded joints with TiO2 coating increased with the increase in welding current and then decreased when the welding current was greater than 130 A. The average microhardness of the heat-affected zone and fusion zone decreased gradually with the increase of welding current.展开更多
The study investigated the application of radiofrequency(RF)-sputtered TiO2 coatings at various temperatures to enhance the hydrophobicity and corrosion resistance of Al6061 alloy.The research aimed to establish a cor...The study investigated the application of radiofrequency(RF)-sputtered TiO2 coatings at various temperatures to enhance the hydrophobicity and corrosion resistance of Al6061 alloy.The research aimed to establish a correlation between the coating process and the resulting surface properties.Surface roughness and wettability were quantified with a surface profilometer and goniometer.Additionally,chemical boiling and salt spray corrosion tests were conducted to evaluate any topographical changes during these procedures.The analysis further involved the use of field-emission scanning electron microscopy(FESEM),energy-dispersive spectroscopy(EDS),and X-ray diffraction(XRD)techniques to characterize the deposited coatings.The findings indicated that the TiO2 coating applied at 500℃exhibited the highest water contact angle and superior corrosion resistance compared to other temperatures.Surface characterization confirmed that this specific TiO_(2) coating at 500℃ effectively delays corrosion due to its hydrophobic behavior,making it durable for industrial applications.展开更多
Bromine has attracted significant attention as a cathode material for aqueous batteries due to its high reduction potential of 1.05 V(Br_(3)^(-)+2e~-■3Br~-),impressive theoretical specific capacity of 223 mA h g^(-1)...Bromine has attracted significant attention as a cathode material for aqueous batteries due to its high reduction potential of 1.05 V(Br_(3)^(-)+2e~-■3Br~-),impressive theoretical specific capacity of 223 mA h g^(-1),and rapid reaction kinetics in the electrolyte.However,searching for compatible anode materials to match with bromine has posed a challenge due to its highly corrosive nature.In this study,we developed oxygen-deficient MoO_(3) with TiO_(2) coating(referred to as MoO_(3-x)@TiO_(2))as an anode material to pair with a bromine cathode in static full batteries.The oxygen deficiency contributes to enhanced electronic and protonic diffusion within the MoO_(3-x)lattice,while the TiO_(2) coating mitigates structural dissolution and proton trapping during cycling.The MoO_(3-x)@TiO_(2) demonstrates fast charge storage kinetics and excellent resistance to bromine corrosion.The impressive compatibility between MoO_(3-x)@TiO_(2) and bromine enables the construction of membrane-less full batteries with exceptional rate capability and cyclic stability.The MoO_(3-x)@TiO_(2)-bromine battery achieves an energy density of70.8 W h kg^(-1)at a power density of 328.1 W kg^(-1),showcasing an impressive long-term cyclic life of 20,000 cycles.Our study provides valuable insights for the development of high-performance aqueous secondary batteries.展开更多
The titanium coatings were prepared on Al_(2)O_(3) balls by mechanical coating technique (MCT),and then the coatings were oxidized to titanium oxides(TiO_(2)) films at 300-600 ℃.The effects of different milling time ...The titanium coatings were prepared on Al_(2)O_(3) balls by mechanical coating technique (MCT),and then the coatings were oxidized to titanium oxides(TiO_(2)) films at 300-600 ℃.The effects of different milling time and oxidation temperature on thickness of films were studied.The composition and microstructure of the films were analyzed by scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS).The results show that the thickest coatings with an average thickness of 20 μm were obtained at the milling time of 15 h.In addition,with the increase of the oxidation temperature,the oxidation of the film is increased.When the milling time is 15 h,the oxidation temperature is 500 ℃,and the addition of photocatalyst is 1 g/mL.The films have the best photocatalytic performance when the degradation rate of methyl orange solution reaches the maximum value of 74.9 %,and the films have a good reusability.展开更多
The"one pot"simultaneous carbon coating and doping of TiO_(2) materials by the hydrolysis of TiCl4 in fructose is reported.The synergistic effect of carbon doping and coating of TiO_(2) to significantly boos...The"one pot"simultaneous carbon coating and doping of TiO_(2) materials by the hydrolysis of TiCl4 in fructose is reported.The synergistic effect of carbon doping and coating of TiO_(2) to significantly boost textural,optical and electronic properties and photocurrent of TiO_(2) for high performance visible light H2 production from water splitting has been comprehensively investigated.Carbon doping can significantly increase the thermal stability,thus inhibiting the phase transformation of the Titania material from anatase to rutile while carbon coating can suppress the grain aggregation of TiO_(2).The synergy of carbon doping and coating can not only ensure an enhanced narrowing effect of the electronic band gap of TiO_(2) thus extending the absorption of photocatalysts to the visible regions,but also promote dramatically the separation of electron-hole pairs.Owing to these synergistic effects,the carbon coated and doped TiO_(2) shows much superior photocatalytic activity for both degradation of organics and photocatalytic/photoelectro chemical(PEC)water splitting under simulated sunlight illumination.The photocatalytic activity of obtained materials can reach 5,4 and 2 times higher than that of pristine TiO_(2),carbon doped TiO_(2) and carbon coated TiO_(2),respectively in the degradation of organic pollutants.The carbon coated and doped TiO_(2) materials exhibited more than 37 times and hundreds of times photocurrent enhancement under simulated sunlight and visible light,respectively compared to that of pristine TiO_(2).The present work providing new comprehensive understanding on carbon coating and doping effect could be very helpful for the development of advanced TiO_(2) materials for a large series of applications.展开更多
Plasma electrolytic oxidation(PEO)was applied using a pulsed unipolar waveform to produce Al_(2)O_(3)−TiO_(2) composite coatings from sol electrolytic solutions containing colloidal TiO_(2) nanoparticles.The sol solut...Plasma electrolytic oxidation(PEO)was applied using a pulsed unipolar waveform to produce Al_(2)O_(3)−TiO_(2) composite coatings from sol electrolytic solutions containing colloidal TiO_(2) nanoparticles.The sol solutions were produced by dissolving 1,3,and 5 g/L of potassium titanyl oxalate(PTO)in a silicate solution.Scanning electron microscopy,energy dispersive spectrometry,X-ray diffraction,and Raman spectroscopy were applied to characterizing the coatings.Corrosion behavior of the coatings was investigated using polarization and impedance techniques.The results indicated that TiO_(2) enters the coating through all types of micro-discharging and is doped into the alumina phase.The higher level of TiO_(2) incorporation results in the decrease of surface micro-pores,while the lower incorporation shows a reverse effect.It was revealed that the higher TiO_(2) content makes a more compact outer layer and increases the inner layer thickness of the coating.Electrochemical measurements revealed that the coating obtained from the solution containing 3 g/L PTO exhibits higher corrosion performance than that obtained in the absence of PTO.The coating produced in the absence of PTO consists of γ-Al_(2)O_(3),δ-Al_(2)O_(3) and amorphous phases,while α-Al_(2)O_(3) is promoted by the presence of PTO.展开更多
The surface of Titanium Hydride (TiH 2) is coated by Nano Titanium Dioxide (TiO 2) particles prepared in both of methods of hydrolysis reaction of Ti(OC 4H 9) 4 and base precipitation reaction of Ti(SO 4) 2. ...The surface of Titanium Hydride (TiH 2) is coated by Nano Titanium Dioxide (TiO 2) particles prepared in both of methods of hydrolysis reaction of Ti(OC 4H 9) 4 and base precipitation reaction of Ti(SO 4) 2. TiH 2 coated with nano TiO 2 particles, in which there is an oxidation film on its surface, shown in the experiments, will obviously achieve good effects on releasing hydrogen slowly in high temperature. There are different structures and properties of TiH 2 coated by nano TiO 2 particles prepared in different ways in high temperature, which can influence on releasing hydrogen.展开更多
文摘This article describes the properties of TiO_2-siloxane that can be appliedto spacecraft polymers to protect from AO environmental influences on the life and performance ofspace mission. This protective coating is obtained by mixing TiO_2, siloxane and silicate mineralsvia dispersion and ground. Kaptons with and without TiO_2-siloxane overcoating are exposed to AOimpingement from ground-simulation laboratory. Fourier transform infrared spectroscopy (FTIR) ,LAMBDA-9 spectrophotometer, X-ray photoelectron spectroscopy (XPS) and scanning electronmicroscopy(SEM) are used to characterize the chemical and physical changes on the surfaces of theunprotected Kapton and protected Kapton samples . The application of protective coatings and theirresistance to the space environment are described for ground-based test. From the test results itcan be seen that Kapton is heavily eroded, while there is little change on surface ofTiO_2-siloxane. So it can be concluded that TiO_2-siloxane coatings are highly resistant to AO andthat it is a kind of protective coating for Kapton.
基金financed by the FOMIX-Yucatán 2008-108160,CONACYT LAB-2009-01-123913,292692,294643,188345,and 204822 projectsthe financial support received from CONACYT。
文摘The high activity of metallic magnesium and alloys limits its potential in biomedical applications;in recent years,extensive efforts have been devoted to modulating this reactivity.In this work,we present Mg(OH)_(2) and TiO_(2)barrier coatings to reduce the degradation of magnesium alloy(Mg-Ca-Zn)surfaces.These coatings were deposited by the anodization method and the spin-coating technique,respectively.The anodized layer was coated with TiO_(2)generated from the hydrolysis of 3%weight of TTIP(Ti[OCH(CH_(3))_(2)]_(4),Titanium(IV)isopropoxide)in 2-Propanol deposited by the spin-coating method.Studying the degradation in Ringer’s solution by electrochemical impedance spectroscopy and OCP revealed a 98%reduction in pittings in uncoated samples after 14 days of immersion.The p H measurements revealed that the TiO_(2)coating reduced the alkalization of the physiological environment,keeping the pH at 6.0 values.In vitro studies of two types of bacteria(E.coli and S.aureus)exhibited zones of inhibition in the agar and activity bactericidal(kill time test).The mechanisms behind the improved degradation resistance and enhanced antibacterial activity are presented and discussed here.Surface modification with Mg(OH)_(2)/TiO_(2)coatings is a promising strategy to control the biodegradation of magnesium implants for bone regeneration.
基金Project(51375511)supported by the National Natural Science Foundation of ChinaProjects(CDJZR12138801,CDJZR11135501,CDJZR13130033)supported by the Fundamental Research Funds for Central Universities of China
文摘The effects of welding current on the macro-morphology, microstructure and mechanical properties of tungsten inert gas(TIG) welded AZ31 magnesium alloy joints with TiO2 coating were investigated. The results showed that the increase of welding current led to the increase in the depth/width ratio and deteriorated the surface appearance of the welded seams with TiO2 coating. The grain size of α-Mg and the amount of granular β-Mg17Al12 particles in the welded seams also increased. The welded joints with TiO2 coating exhibited a deeper weld penetration and larger grain size compared with the welded joint without TiO2 coating. When the welding current was less than 130 A, the ultimate tensile strength of the welded joints with TiO2 coating increased with the increase in welding current and then decreased when the welding current was greater than 130 A. The average microhardness of the heat-affected zone and fusion zone decreased gradually with the increase of welding current.
文摘The study investigated the application of radiofrequency(RF)-sputtered TiO2 coatings at various temperatures to enhance the hydrophobicity and corrosion resistance of Al6061 alloy.The research aimed to establish a correlation between the coating process and the resulting surface properties.Surface roughness and wettability were quantified with a surface profilometer and goniometer.Additionally,chemical boiling and salt spray corrosion tests were conducted to evaluate any topographical changes during these procedures.The analysis further involved the use of field-emission scanning electron microscopy(FESEM),energy-dispersive spectroscopy(EDS),and X-ray diffraction(XRD)techniques to characterize the deposited coatings.The findings indicated that the TiO2 coating applied at 500℃exhibited the highest water contact angle and superior corrosion resistance compared to other temperatures.Surface characterization confirmed that this specific TiO_(2) coating at 500℃ effectively delays corrosion due to its hydrophobic behavior,making it durable for industrial applications.
基金the financial support from the National Key Research and Development Program of China(2022YFB2502003)the Guangdong Basic and Applied Basic Research Foundation(2023B1515040011)。
文摘Bromine has attracted significant attention as a cathode material for aqueous batteries due to its high reduction potential of 1.05 V(Br_(3)^(-)+2e~-■3Br~-),impressive theoretical specific capacity of 223 mA h g^(-1),and rapid reaction kinetics in the electrolyte.However,searching for compatible anode materials to match with bromine has posed a challenge due to its highly corrosive nature.In this study,we developed oxygen-deficient MoO_(3) with TiO_(2) coating(referred to as MoO_(3-x)@TiO_(2))as an anode material to pair with a bromine cathode in static full batteries.The oxygen deficiency contributes to enhanced electronic and protonic diffusion within the MoO_(3-x)lattice,while the TiO_(2) coating mitigates structural dissolution and proton trapping during cycling.The MoO_(3-x)@TiO_(2) demonstrates fast charge storage kinetics and excellent resistance to bromine corrosion.The impressive compatibility between MoO_(3-x)@TiO_(2) and bromine enables the construction of membrane-less full batteries with exceptional rate capability and cyclic stability.The MoO_(3-x)@TiO_(2)-bromine battery achieves an energy density of70.8 W h kg^(-1)at a power density of 328.1 W kg^(-1),showcasing an impressive long-term cyclic life of 20,000 cycles.Our study provides valuable insights for the development of high-performance aqueous secondary batteries.
基金Funded by University-level Project of Jincheng College of Sichuan University(No.2020jcky0014)。
文摘The titanium coatings were prepared on Al_(2)O_(3) balls by mechanical coating technique (MCT),and then the coatings were oxidized to titanium oxides(TiO_(2)) films at 300-600 ℃.The effects of different milling time and oxidation temperature on thickness of films were studied.The composition and microstructure of the films were analyzed by scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS).The results show that the thickest coatings with an average thickness of 20 μm were obtained at the milling time of 15 h.In addition,with the increase of the oxidation temperature,the oxidation of the film is increased.When the milling time is 15 h,the oxidation temperature is 500 ℃,and the addition of photocatalyst is 1 g/mL.The films have the best photocatalytic performance when the degradation rate of methyl orange solution reaches the maximum value of 74.9 %,and the films have a good reusability.
基金supported by the National Natural Science Foundation of China(U1663225,21805280)Program for Changjiang Scholars and Innovative Research Team in University(IRT15R52)+2 种基金the Minstry of Education of Chinathe 111 Project(Grant No.B20002)from the Ministry of Science and Technology and the Ministry of Education of China,China,European Commission,Interreg V France-Wallonie-Vlaanderen(Depollutair)the Fundamental Research Funds for the Central Universities(WUT:2017III001),Chinathe FJIRSM&IUE Joint Research Fund(RHZX-2018-002),China for supporting this work。
文摘The"one pot"simultaneous carbon coating and doping of TiO_(2) materials by the hydrolysis of TiCl4 in fructose is reported.The synergistic effect of carbon doping and coating of TiO_(2) to significantly boost textural,optical and electronic properties and photocurrent of TiO_(2) for high performance visible light H2 production from water splitting has been comprehensively investigated.Carbon doping can significantly increase the thermal stability,thus inhibiting the phase transformation of the Titania material from anatase to rutile while carbon coating can suppress the grain aggregation of TiO_(2).The synergy of carbon doping and coating can not only ensure an enhanced narrowing effect of the electronic band gap of TiO_(2) thus extending the absorption of photocatalysts to the visible regions,but also promote dramatically the separation of electron-hole pairs.Owing to these synergistic effects,the carbon coated and doped TiO_(2) shows much superior photocatalytic activity for both degradation of organics and photocatalytic/photoelectro chemical(PEC)water splitting under simulated sunlight illumination.The photocatalytic activity of obtained materials can reach 5,4 and 2 times higher than that of pristine TiO_(2),carbon doped TiO_(2) and carbon coated TiO_(2),respectively in the degradation of organic pollutants.The carbon coated and doped TiO_(2) materials exhibited more than 37 times and hundreds of times photocurrent enhancement under simulated sunlight and visible light,respectively compared to that of pristine TiO_(2).The present work providing new comprehensive understanding on carbon coating and doping effect could be very helpful for the development of advanced TiO_(2) materials for a large series of applications.
文摘Plasma electrolytic oxidation(PEO)was applied using a pulsed unipolar waveform to produce Al_(2)O_(3)−TiO_(2) composite coatings from sol electrolytic solutions containing colloidal TiO_(2) nanoparticles.The sol solutions were produced by dissolving 1,3,and 5 g/L of potassium titanyl oxalate(PTO)in a silicate solution.Scanning electron microscopy,energy dispersive spectrometry,X-ray diffraction,and Raman spectroscopy were applied to characterizing the coatings.Corrosion behavior of the coatings was investigated using polarization and impedance techniques.The results indicated that TiO_(2) enters the coating through all types of micro-discharging and is doped into the alumina phase.The higher level of TiO_(2) incorporation results in the decrease of surface micro-pores,while the lower incorporation shows a reverse effect.It was revealed that the higher TiO_(2) content makes a more compact outer layer and increases the inner layer thickness of the coating.Electrochemical measurements revealed that the coating obtained from the solution containing 3 g/L PTO exhibits higher corrosion performance than that obtained in the absence of PTO.The coating produced in the absence of PTO consists of γ-Al_(2)O_(3),δ-Al_(2)O_(3) and amorphous phases,while α-Al_(2)O_(3) is promoted by the presence of PTO.
文摘The surface of Titanium Hydride (TiH 2) is coated by Nano Titanium Dioxide (TiO 2) particles prepared in both of methods of hydrolysis reaction of Ti(OC 4H 9) 4 and base precipitation reaction of Ti(SO 4) 2. TiH 2 coated with nano TiO 2 particles, in which there is an oxidation film on its surface, shown in the experiments, will obviously achieve good effects on releasing hydrogen slowly in high temperature. There are different structures and properties of TiH 2 coated by nano TiO 2 particles prepared in different ways in high temperature, which can influence on releasing hydrogen.
