Dynamic Coupling Analysis of Semisubmersible Platform Float-over Method for Docking Case

In this paper,the multi-body coupled dynamic characteristics of a semisubmersible platform and an HYSY 229 barge were investigated.First,coupled hydrodynamic analysis of the HYSY 229 barge and the semisubmersible platform was performed.Relevant hydrodynamic parameters were obtained using the retardation function method of three-dimensional frequency-domain potential flow theory.The results of the hydrodynamic analysis were highly consistent with the test findings,verifying the accuracy of the multifloating hydrodynamic coupling analysis,and key hydrodynamic parameters were solved for different water depths and the coupling effect.According to the obtained results,the hydrodynamic influence was the largest in shallow waters when the coupling effect was considered.Furthermore,the coupled motion equation combined with viscous damping,fender system,and mooring system was established,and the hydrodynamics,floating body motion,and dynamic response of the fender system were analyzed.Motion analysis revealed good agreement among the surge,sway,and yaw motions of the two floating bodies.However,when the wave period reached 10 s,the motion of the two floating bodies showed severe shock,and a relative motion was also observed.Therefore,excessive constraints should be added between the two floating bodies during construction to ensure construction safety.The numerical analysis and model test results of the semisubmersible platform and HYSY 229 barge at a water depth of 42 m and sea conditions of 0°,45°,and 90° were in good agreement,and the error was less than 5%.The maximum movement of the HYSY 229 barge reached 2.61 m in the sway direction,whereas that of the semisubmersible platform was 2.11 m.During construction,excessive constraints should be added between the two floating bodies to limit their relative movement and ensure construction safety.

Time-Domain Analysis of Underground Station-Layered Soil Interaction Based on High-Order Doubly Asymptotic Transmitting Boundary

Based on the modified scale boundary finite element method and continued fraction solution,a high-order doubly asymptotic transmitting boundary(DATB)is derived and extended to the simulation of vector wave propagation in complex layered soils.The high-order DATB converges rapidly to the exact solution throughout the entire frequency range and its formulation is local in the time domain,possessing high accuracy and good efficiency.Combining with finite element method,a coupled model is constructed for time-domain analysis of underground station-layered soil interaction.The coupled model is divided into the near and far field by the truncated boundary,of which the near field is modelled by FEM while the far field is modelled by the high-order DATB.The coupled model is implemented in an open source finite element software,OpenSees,in which the DATB is employed as a super element.Numerical examples demonstrate that results of the coupled model are stable,accurate and efficient compared with those of the extended mesh model and the viscous-spring boundary model.Besides,it has also shown the fitness for long-time seismic response analysis of underground station-layered soil interaction.Therefore,it is believed that the coupled model could provide a new approach for seismic analysis of underground station-layered soil interaction and could be further developed for engineering.

Brillouin optical time-domain analysis for geotechnical monitoring

In this paper, we show some recent experimental applications of Brillouin optical time-domain analysis （BOTDA） based sensors for geotechnical monitoring. In particular, how these sensors can be applied to detecting early movements of soil slopes by the direct embedding of suitable fiber cables in the ground is presented. Furthermore, the same technology can be used to realize innovative inclinometers, as well as smart foundation anchors.

Adsorption and Transfer Properties for Toluene and pDichlorobenzene in Dense CO_2/Silica Gel Packed Bed System by Moment Method and Time-Domain Analysis

Based on chromatographic theory, the moment method and the time-domain fitting analysis were applied to measure and evaluate the adsorption equilibrium constant and mass transfer properties (axial dispersion coefficient and effective intra-particle diffusivity) for toluene and p-dichlorobenzene on silica gel adsorbent in the subcritical and supercritical CO2. An apparatus based on supercritical fluid chromatography was established and the experiments were performed at temperatures of 298.15-318.15 K and pressures of 7.5-17.8 MPa. The two methods have been compared. The results show that for the systems studied here the moment method can give reasonable values for both adsorption equilibrium constant and mass transfer properties, but the time-domain analysis only can obtain the adsorption equilibrium constant. The dependence of adsorption equilibrium constant and mass transfer properties on temperature and pressure was investigated.

Numerical analysis of multicomponent responses of surface-hole transient electromagnetic method

We calculate the multicomponent responses of surface-hole transient electromagnetic method. The methods and models are unsuitable as geoelectric models of conductive surrounding rocks because they are based on regular local targets. We also propose a calculation and analysis scheme based on numerical simulations of the subsurface transient electromagnetic fields. In the modeling of the electromagnetic fields, the forward modeling simulations are performed by using the finite-difference time-domain method and the discrete image method, which combines the Gaver–Stehfest inverse Laplace transform with the Prony method to solve the initial electromagnetic fields. The precision in the iterative computations is ensured by using the transmission boundary conditions. For the response analysis, we customize geoelectric models consisting of near-borehole targets and conductive wall rocks and implement forward modeling simulations. The observed electric fields are converted into induced electromotive force responses using multicomponent observation devices. By comparing the transient electric fields and multicomponent responses under different conditions, we suggest that the multicomponent-induced electromotive force responses are related to the horizontal and vertical gradient variations of the transient electric field at different times. The characteristics of the response are determined by the varying the subsurface transient electromagnetic fields, i.e., diffusion, attenuation and distortion, under different conditions as well as the electromagnetic fields at the observation positions. The calculation and analysis scheme of the response consider the surrounding rocks and the anomalous field of the local targets. It therefore can account for the geological data better than conventional transient field response analysis of local targets.

Distributed Fiber Optic Monitoring and Stability Analysis of a Model Slope under Surcharge Loading

In the discipline of geotechnical engineering, fiber optic sensor based distributed monitoring has played an increasingly important role over the past few decades. Compared with conventional sensors, fiber optic sensors have a variety of exclusive advantages, such as smaller size, higher precision, and better corrosion resistance. These innovative monitoring technologies have been successfully applied for performance monitoring of geo-structures and early warning of potential geo- hazards around the world. In order to investigate their ability to monitor slope stability problems, a medium-sized model of soil nailed slope has been constructed in laboratory. The fully distributed Brillouin optical time-domain analysis （BOTDA） sensing technology was employed to measure the horizontal strain distributions inside the model slope. During model construction, a specially designed strain sensing fiber was buried in the soil mass. Afterward, the surcharge loading was applied on the slope crest in stages using hydraulic jacks and a reaction frame. During testing, an NBX-6o5o BOTDA sensing interrogator was used to collect the fiber optic sensing data. The test results have been analyzed in detail, which shows that the fiber optic sensors can capture the progressive deformation and failure pattern of the model slope. The limit equilibrium analyses were also conducted to obtain the factors ofsafety of the slope under different surface loadings. It is found that the characteristic maximum strains can reflect the stability of the model slope and an empirical relationship was obtained, This study verified the effectiveness of the distributed BOTDA sensing technology in performance monitoring of slope.

Assessment of right ventricular afterload by pressure waveform analysis in acute pulmonary hypertension

AIM: To characterize hydraulic right ventricle (RV) af- terload by pulmonary arterial pressure waveform analy- sis in an acute pulmonary hypertension (PH) model. METHODS: Pulmonary artery (PA) flow and pressure were recorded in six anesthetized sheep. Acute iso- baric PH was induced by phenylephrine (active) and PA mechanical constriction (passive). We estimated the amplitude of the forward and reflected pressure waves according to the inflection point. In most cases the in- flection pressure was smooth, thus the inflection point was defined as the time at which the first derivative ofpulmonary arterial pressure reached its first minimum. We calculated the input and characteristic (Z C , time- domain Li method) impedances, the capacitance index (stroke volume/pulse pressure), the augmentation index (AI) (reflected pressure/pulse pressure), the frac- tional pulse pressure (pulse pressure/mean pressure) and the wasted energy generated by the RV due to wave reflection during ejection (E W ). RESULTS: Pulse pressure, fractional pulse pressure, AI and Z C increased and capacitance index decreased during passive PH with respect to control (P < 0.05). In contrast, Z C and the capacitance index did not change and E W and the AI decreased during active PH. Pulse pressure correlated with E W and Z C and the AI was cor- related with E W (r > 0.6, P < 0.05). CONCLUSION: PA pressure waveform analysis al- lows the quantification of the dynamic RV afterload. Prospective clinical studies will be necessary to validate this time-domain approach to evaluate the dynamic RV afterload in chronic PH.

Isotopic analysis based on terahertz spectrum

As a new promising detection technology in the terahertz research field,the terahertz time-domain spec-troscopy(THz-TDS)has very broad application potential in many fields because its advantage on the characteristic spectrum,wide spectrum and non-destructive analysis of interested substances.In this paper,the terahertz absorption spectra of gases mixed with 12 CO and 13 CO in the spec-trum range of 0.5–2.5 THz are measured by terahertz time-domain spectroscopy for the first time.Several isotopo-logues can be clearly distinguished based on the difference in their rotational energies and the consequent terahertz spectrum.The experimental results show that 12 CO and 13 CO have obvious characteristic absorption peaks in the spectrum range of 0.5–2.5 THz due to the difference in rotational energy,and the rotational constant B can be calculated according to the experimental values to distin-guish the two gaseous isotopologues.The frequency posi-tions of the characteristic absorption peak measured by this experiment and the rotation constant B calculated accord-ing to the experimental values are compared with those previous theoretical calculations and experimental results,and they are in good agreement.This result lays a foun-dation for developing more sophisticated terahertz instru-ments to the detection of different isotopologues.

Analysis of photonic crystal on LED extraction efficiency

Because of its very low light extraction efficiency(LEE),LED is limited to be widely used under the condition of the internal quantum efficiency which up to 90%.In order to fullfill the design of a more efficient GaN-based blue light LED,the model including deeply etched surface photonic crystals(PhCs)LED is discussed using mode analysis method from light waveguide theory.The distributions of all order modes in GaN layer are obtained by the effective index approximation.The light extraction efficiencies are also calculated by finite-difference time-domain method(FDTD).The emulated results fully coincide with the former analysis.Because the manufacture of the surface photonic crystal is feasible,the work can be very meaningful to design and manufacture the high efficiency GaN-based blue light LED in factory for a large amount.

A Time-Domain Method for Hydroelastic Analysis of A Moored Oil Storage Vessel in Wind,Irregular Waves and Currents

The hydroelastic behavior of a moored oil storage vessel subjected to arbitrary time-dependent external loads,which include wind,waves,and currents with different incident directions,is investigated with the time-domain modal expansion method.First,the water boundary integral equations on the body surface of a quarter model,which can be obtained via the free-surface Green’s function method,are established.Then,the time-dependent elastic deflection of the moored oil storage vessel is expressed by a superposition of modal functions and corresponding modal amplitudes,and a Galerkin scheme is applied to derive the linear system of equations for the modal amplitudes.The second-order linear differential equations for modal amplitudes are solved via the fourth-order Runge−Kutta method.The present model is validated against existing frequency domain results for a truncated cylinder and a VLFS.Numerical calculations for the moored oil storage vessel are then conducted to obtain the time series of various modal amplitudes and elastic displacements of the measurement points and the corresponding spectra with different incident directions.

PC-based artif icial neural network inversion for airborne time-domain electromagnetic data

Traditionally, airborne time-domain electromagnetic （ATEM） data are inverted to derive the earth model by iteration. However, the data are often highly correlated among channels and consequently cause ill-posed and over-determined problems in the inversion. The correlation complicates the mapping relation between the ATEM data and the earth parameters and thus increases the inversion complexity. To obviate this, we adopt principal component analysis to transform ATEM data into orthogonal principal components （PCs） to reduce the correlations and the data dimensionality and simultaneously suppress the unrelated noise. In this paper, we use an artificial neural network （ANN） to approach the PCs mapping relation with the earth model parameters, avoiding the calculation of Jacobian derivatives. The PC-based ANN algorithm is applied to synthetic data for layered models compared with data-based ANN for airborne time-domain electromagnetic inversion. The results demonstrate the PC-based ANN advantages of simpler network structure, less training steps, and better inversion results over data-based ANN, especially for contaminated data. Furthermore, the PC-based ANN algorithm effectiveness is examined by the inversion of the pseudo 2D model and comparison with data-based ANN and Zhody＇s methods. The results indicate that PC-based ANN inversion can achieve a better agreement with the true model and also proved that PC-based ANN is feasible to invert large ATEM datasets.

Detecting damage to offshore platform structures using the time-domain data

A new method that uses time-domain response data under random loading is proposed for detecting damage to the structural elements of offshore platforms. In our study, a time series model with a fitting order was first constructed using the time-domain of noise data. A sensitivity matrix consisting of the first differential of the autoregressive coefficients of the time series models with respect to the stiffness of structural elements was then obtained based on time-domain response data. Locations and severity of damage may then be estimated by solving the damage vector whose components express the degrees of damage to the structural elements. A unique aspect of this detection method is that it requires acceleration history data from only one or a few sensors. This makes it feasible for a limited array of sensors to obtain sufficient data. The efficiency and reliability of the proposed method was demonstrated by applying it to a simplified offshore platform with damage to one element. Numerical simulations show that the use of a few sensors’ acceleration history data, when compared with recorded levels of noise, is capable of detecting damage efficiently. An increase in the number of sensors helps improve the diagnosis success rate.

A Service-Based Intelligent Time-Domain and Spectral-Domain Flow Aggregation in IP-over-EON Based on SDON

The rapid growth of IP traffic has contributed to wide deployment of optical devices in elastic optical network.However,the passband shape of wavelength selective switches(WSSs)that are used in reconfigurable optical add-drop multiplexer(ROADM)/optical cross connect(OXC)is not ideal,causing the narrowing of spectrum.Spectral narrowing will lead to signal impairment.Therefore,guard-bands need to be inserted between adjacent paths which will cause the waste of resources.In this paper,we propose a service-based intelligent aggregation node selection and area division(ANS-AD)algorithm.For the rationality of the aggregation node selection,the ANS-AD algorithm chooses the aggregation nodes according to historical traffic information based on big data analysis.Then the ANS-AD algorithm divides the topology into areas according to the result of the aggregation node selection.Based on the ANS-AD algorithm,we propose a time-domain and spectral-domain flow aggregation(TS-FA)algorithm.For the purpose of reducing resources'waste,the TS-FA algorithm attempts to reduce the insertion of guard-bands by time-domain and spectral-domain flow aggregation.Moreover,we design a time-domain and spectral-domain flow aggregation module on software defined optical network(SDON)architecture.Finally,a simulation is designed to evaluate the performance of the proposed algorithms and the results show that our proposed algorithms can effectively reduce the resource waste.

Time-domain analysis methodology for large-scale RLC circuits and its applications

With soaring work frequency and decreasing feature sizes, VLSI circuits with RLC parasitic components are more like analog circuits and should be carefully analyzed in physical design. However, the number of extracted RLC components is typically too large to be analyzed efficiently by using present analog circuit simulators like SPICE. In order to speedup the simulations without error penalty, this paper proposes a novel methodology to compress the time-descritized circuits resulted from numerical integration approximation at every time step. The main contribution of the methodology is the efficient structure-level compression of DC circuits containing many current sources, which is an important complement to present circuit analysis theory. The methodology consists of the following parts： 1） An approach is proposed to delete all intermediate nodes of RL branches. 2） An efficient approach is proposed to compress and back-solve parallel and serial branches so that it is error-free and of linear complexity to analyze circuits of tree topology. 3） The Y to πtransformation method is used to error-free reduce and back-solve the intermediate nodes of ladder circuits with the linear complexity. Thus, the whole simulation method is very accurate and of linear complexity to analyze circuits of chain topology. Based on the methodology, we propose several novel algorithms for efficiently solving RLC-model transient power/ground （P/G） networks. Among them, EQU-ADI algorithm of linear-complexity is proposed to solve RLC P/G networks with mesh-tree or mesh-chain topologies. Experimental results show that the proposed method is at least two orders of magnitude faster than SPICE while it can scale linearly in both time- and memory-complexity to solve very large P/G networks.

HF-VHF dual-channel multifunctional radio astronomy terminal system

The high frequency-very high frequency(HF-VHF)frequency band is of significant importance in astronomical observations,with applications studying various phenomena such as space weather,solar radio emissions,planetary eruptions in the solar system,pulsars,transient sources,and reionization of the early universe.This article introduces the HF-VHF frequency band multifunctional radio astronomical terminal system based on a dual-channel high-speed acquisition board with a frequency observation range of 1-250 MHz and a sampling rate of 500 Msps(Mega samples per second).The maximum quantization bit of the system is 14 bits,with a maximum time resolution of 0.1 s and a maximum spectral resolution of 16 kHz.The system combines spectral analysis of solar radio signals and recording of time-domain data of signals interfering with long baselines,and adopts a server-client separation mode to allow remote operation with separate permissions.It is used in the China-Malaysia joint astronomy project,which can carry out single-site observation of solar radio signals as well as interferometric observation of signals from multiple sites.

Time-domain analysis for vibration and sound radiation of submerged spherical shell excited by force

The vibration and sound radiation of a submerged spherical shell are studied in the time-domain by Laplace transform method, where a CW pulse force acts at the apex of the shell. The numerical results for the case of long pulse show that the different vibrational modes and the resonant or beat radiated sound are excited for different carrier-frequencies, but litle sound is radiated for some vibrational modes. For the case of short pulse the waveforms of the pulse become widened and deformed, when the pulse propagates between apexes of the shell. Then, the Doubly Asymptotic Approximations (DAA2) and Kirchhoff's Retarded Potential Formulate (KRPF)are used to solve the same problem. It is shown that the results of DAA2 and KRPF method have a good agreement with the results of Laplace transform method.

Depolarization Degree to Determine Dihedral Attribute of Radar Target

This paper investigates the ability of the depolarization degree, derived from the characteristic polarization states at the resonant frequency set, to identify corner or swept, i.e. dihedral, changes in same-class targets by a metallic wire example. A well-estimated depolarization degree requires a robust extraction of the fundamental target resonance set in two orthogonal sets of fully co-polarized and cross-polarized polarization channels, then finding the null polarization states using the Lagrangian method. Such depolarization degree per resonance mode has the potential to form a robust feature set because it is relatively less sensitive to onset ambiguity, invariant to rotation, and could create a compact, recognizable, and separable distribution in the proposed feature space. The study was limited to two targets with two swept changes of fifteen degrees within normal incidence;under a supervised learning approach, the results showed that the identification rate converging to upper-bound (100%) for a signal-to-noise ratio above 20 dB and lower-bound around (50%) below −10 dB.

Sensitivity analysis of fatigue life prediction for deepwater steel lazy wave catenary risers

Steel lazy wave catenary riser (SLWR) has been an attractive choice for deepwater oil field developments. However, fatigue is a critical issue in assessing the feasibility of applying SLWR to large motion vessels such as floating production storage and offloading (FPSO) or semi-submersibles. In this work, the time-domain fatigue analysis of SLWR was adopted for better representing the structural nonlinearity, fluid load nonlinearity and riser-soil nonlinear interaction. The Palmgren-Miner rule was employed for the fatigue life prediction along the riser length. The main purpose of this analysis is to present sensitivity analyses of SLWR fatigue life under various input parameters, which include the structural damping, the hydrodynamic coefficients along the riser, the seabed stiffness, the vessel motions, etc. The analyses indicated the strong dependence of the riser fatigue life on these parameters. The results can help designers to understand the dynamic behavior of the SLWR and provide guidance for selection of some critical parameters that are used in the fatigue design.

Numerical and Experimental Research on the Global Performances of Cell-Truss Spar Platform

Spar technology has been applied to the deep-sea oil and gas exploitation for several years. From the first generation of classic spar, the spar platform has developed into the second generation of truss spar and the latest cell spar. Owing to its favorable adaptability to wide range of water depth and benign motion performances, spar has aroused quite a lot of interests from oil companies, universities and research institutes. In the present paper, a new cell-truss spar concept, put forward by the State Key Laboratory of Ocean Engineering （SKLOE） at Shanghai Jiao Tong University, is studied both numerically and experimentally. The numerical simulation was conducted by means of nonlinear time-domain fully coupled analysis, and its results were compared to the experimental data. Whereafter, detailed analysis was carried out to obtain the global performances of＇ the new spar concept. Proposals for the improvement of numerical calculation and experimental technique were tabled meanwhile.

Modeling and Sliding Mode Control with Boundary Layer for Unmanned Coaxial Rotor Ducted Fan Helicopter

The structure and modeling of a novel unmanned coaxial rotor ducted fan helicopter(RDFH)are introduced,and then,based on the helicopter air dynamics and kinematics principles,a nonlinear model of the coaxial rotor ducted fan helicopter is developed and implemented on the basis of the wind tunnel experiment.After that,the helicopter′s stability and coupling characteristics of manipulation are analyzed through time-domain.Finally,a sliding mode controller(SMC)with boundary layers is developed on a hardware in the loop platform using digital signal processor(DSP)as the flight control computer.The results show that the RDFH′s tracking ability performs well under the use of proposed controller.