An Actively Mode-Locked Ho:YAG Solid-Laser Pumped by a Tm-Doped Fiber Laser

An actively mode-locked Ho： YAG laser pumped by a diode-pumped Tin-doped fiber laser is reported. For the cw operation, we obtain the maximum output power of 3.43 W with a central wavelength 2022.2nm at the maximum incident pump power of 11.4 W, corresponding to a slope efficiency of 34.5%. The beam quality factor M2 is 1.16, and the output beam is close to fundamental TEMoo. In the case of the CWML operation, a stable pulse train is generated with an average output power up to 3.41 W with a slope efficiency of 34.3% at the incident pump power of 11.4 W and a pulse duration of 294ps at a repetition rate of 81.92MHz. In addition, the maximum single pulse energy is 41.6nJ.

Fabrication of Tm-Doped Fibers for High Power and 121W Output All-Fiber Tm-Doped Fiber Laser

We fabricate the Tm-doped double cladding silica fiber by using the vapor-solution hybrid-doping method, then build up an all-fiber Tin-doped fiber laser which can provide the output power of up to 121 W, corresponding to a slope efficiency of 51% and an optical-optical efficiency of 48%. By using the domestic Tin-doped fiber, it is the first time a hundred-watt level output at 1915nm has been achieved, to the best of our knowledge. The thermal effect of Tm-doped fiber laser is also analyzed.

Synchronously Pumped Mode-Locked 1.89 μm Tm-Doped Fiber Laser with High Detuning Toleration

We propose and demonstrate a synchronously pumped mode-locked Tm-doped fiber（TDF） laser without any extra mode-locking elements. Pumped by a 1.56 μm pulse fiber laser, the TDF laser generates 1.17 ps pulses with a spectral width of 9.7 nm and a repetition rate of 9.33 MHz. The emission wavelength is tunable along with the cavity length detuning in a wide range of 3 mm. The high detuning toleration is beneficial to achieve high temperature and vibration stability in all-fiber configuration lasers.

Heat-treated microstructure and mechanical properties of laser solid forming Ti-6Al-4V alloy

The effects of heat treatment on the microstructure and mechanical properties of laser solid forming （LSF） Ti-6Al-4V alloy were investigated The influences of the temperature and time of solution treatment and aging treatment were analyzed. The results show that the microstructure of LSFed samples consists of Widmanstatten α laths and a little acicular in columnar prior β grains with an average grain width of 300 μm, which grow epitaxiaUy from the substrate along the deposition direction （27）. Solution treatment had an important effect on the width, aspect ratio, and volmne fraction of primary and secondary a laths, and aging treatment mainly affects the aspect ratio and volume fraction of primary α laths and the width and volume fraction of secondary a laths. Globular a phase was first observed in LSFed samples when the samples were heat treated with solution treatment （950℃, 8 h/air cooling （AC）） or with solution treatment （950℃, 1 h/AC） and aging treatment （550℃, above 8 h/AC）, respectively. The coarsening and globularization mechanisms of a phase in LSFed Ti-6Al-4V alloy during heat treatment were presented. To obtain good integrated mechanical properties for LSFed Ti-6Al-4V alloys, an optimized heat treatment regimen was suggested.

Effect of Intermediate Heat Treatment Temperature on Microstructure and Notch Sensitivity of Laser Solid Formed Inconel 718 Superalloy

Inconel 718 superalloys deposited by laser solid forming （LSF） were heat treated with solution treatment,intermediate heat treatment （IHT） and two-stage aging treatment in sequence （SITA heat treatment）.The effect of IHT temperature on microstructure,tensile property and notch sensitivity of LSFed Inconel 718 superalloy at 500 ℃ were investigated.As-deposited columnar grains have transformed to equiaxed grains and the grains were refined due to the recrystallization during the SITA heat treatment.It is found that the size and amount of δ phase dispersed at grain boundaries decreased with the increasing of IHT temperature,and δ phase disappeared when the IHT temperature reached 1 020 ℃.The ultimate tensile strength （UTS） and yield strength （YS） of smooth samples increased to a maximum when the IHT temperature reached 980 ℃ and then decreased slightly to a minimum when the IHT temperature was 1 000 ℃,and followed by slight increasing again till the IHT temperature reached 1 020 ℃,resulted from the competition of precipitation strengthening effect of γ″ and γ＇ phase and the grain boundary weakening effect caused by the gradual disappearance of δ phase with increasing the IHT temperature.The notch sensitivity factor （qe） decreased but still greater than 1 as the IHT temperature increased,which is attributed to the decrease of the size and amount of δ precipitation.

Fe-Zn supersaturated solid solution prepared by mechanical alloying and laser sintering to accelerate degradation

The slow degration of iron limits its bone implant application.The solid solution of Zn in Fe is expected to accelerate the degradation.In this work,mechanical alloying(MA)was used to prepare Fe-Zn powder with supersaturated solid solution.MA significantly decreased the lamellar spacing between particles,thus reducing the diffusion distance of solution atoms.Moreover,it caused a number of crystalline defects,which further promoted the solution diffusion.Subsequently,the MA-processed powder was consolidated into Fe-Zn part by laser sintering,which involved a partial melting/rapid solidification mechanism and retained the original supersaturated solid solution.Results proved that the Fe-Zn alloy became more susceptible with a lowered corrosion potential,and thereby an accelerated corrosion rate of(0.112±0.013)mm/year.Furthermore,it also exhibited favorable cell behavior.This work highlighted the advantage of MA combined with laser sintering for the preparation of Fe-Zn implant with improved degradation performance.

Medium performance effect on the high output energy from a xenon lamp-pumped pyrromethene-567 solid-state dye laser

In order to obtain a high output energy from a xenon lamp-pumped solid-state dye laser, homogeneities of laser mediums and flatnesses of medium faces with different processing treatments are discussed in the paper. The mediums without aging treatment, which are prepared by using a prepolymer process and have diamond-machined end faces to produce the required optical finish, give a highest laser output of 281.9 mJ with 0.215% slope efficiency at 2.0x 10^-4 mol/L. The best medium lifetime is 21 shots to 50% of original output equating 74.6 k J/liter.

Influence of processing parameters on deposition characteristics of Inconel 625 superalloy fabricated by laser solid forming

A series of single track clads of Inconel 625 alloy were fabricated by laser solid forming.To achieve the high dimensional accuracy and excellent mechanical properties,the effect of processing parameters on the geometry,the formation of Laves phase and the residual stress was investigated.The results show that laser power and scanning speed had a dramatical influence on the width and height of single-track clads.According to the columnar to equiaxed transition curve of Inconel 625,the grain morphology can be predicted during the LSF process.With the increasing laser power and the decreasing scanning speed,the segregation degree of Si,Nb,Mo,the volume fraction and size of Laves phase increased.Vickers indentation was used to demonstrate that optimizing processing parameter can achieve the minimum residual tensile stress.

Controllable combustion behaviors of the laser-controlled solid propellant

Microsatellites have been widely applied in the fields of communication,remote sensing,navigation and science exploration due to its characteristics of low cost,flexible launch mode and short development period.However,conventional solid-propellant have difficulties in starting and interrupting combustion because combustion is autonomously sustained after ignition Herein,we proposed a new type of solid-propellant named laser-controlled solid propellant,which is sensitive to laser irradiation and can be started or interrupted by switching on/off the continuous wave laser.To demonstrate the feasibility and investigate the controllable combustion behaviors under different laser on/off conditions,the combus tion parameters including burning rate,ignition delay time and platform pressure were tested using pressure sensor,high-speed camera and thermographic camera.The results showed that the increase of laser-on or laser-off duration both will lead to the decrease of propellant combustion performance during re-ignition and re-combustion process.This is mainly attributed to the laser attenuation caused by the accumulation of combustion residue and the change of chamber ambient temperature.Simultaneously the multiple ignition tests revealed that the increased chamber ambient temperature after combustion can make up for the energy loss of laser attenuation and expansion of chamber cavity.However,the laser-controlled combustion performance of solid propellant displayed a decrease trend with the addi-tion of ignition times.Nevertheless,the results still exchibited good laser-controlled agility of laser-controlled solid propellant and manifested its inspiring potential in many aspects of space missions.

New Progress on All Solid State Laser Technology in China

1 Significance of All Solid State Laser (DPL) Technology in Field of LaserBecause of the advantages of high conversion efficiency, good beam quality, small size and light weight, DPL becomes the hotspot and priority of development of laser technology. It may be the main body of laser in the future and replace gas laser and liquid laser. It is a great revolution of laser technology.The developed countries vie in developing DPL. China has achieved great success in this field, but there is a wide gap between the developed countries and us. We should attach great importance to it.

Superplastic solid state welding of steel and copper alloy based on laser quenching of steel surface

Based on the feasibility of isothermal superplastic solid state welding of steel and copper alloy, the welded surface of steel surface was ultra-fined through laser quenching, and then the welding process tests between different base metals of 40Cr and QCr0.5 were made under the condition of non vacuum and non shield gas. The experimental results show that, with the sample surface of steel after laser quenching and that of copper alloy carefully cleaned, and under the pre-pressed stress of 56.684.9 MPa, at the welding temperature of 750800 ℃ and at initial strain rate of （2.57.5）×10-4 s-1, the solid state welding can be finished in 120180 s so that the strength of the joint is up to that of QCr0.5 base metal and the expansion rate of the joint does not exceed 6%. The plastic deformation of the joint was further analysed. The superplastic deformation of the copper alloy occurs in welding process and the deformation of steel are little.

Theoretical analysis and numerical simulation of the impulse delivering from laser-produced plasma to solid target

A plasma is produced in air by using a high-intensity Q-switch Nd：YAG pulsed laser to irradiate a solid target, and the impulses delivering from the plasma to the target are measured at different laser power densities. Analysing the formation process of laser plasma and the laser supported detonation wave （LSDW） and using fluid mechanics theory and Pirri＇s methods, an approximately theoretical solution of the impulse delivering from the plasma to the target under our experimental condition is found. Furthermore, according to the formation time of plasma and the variation of pressure in plasma in a non-equilibrium state, a physical model of the interaction between the pulse laser and the solid target is developed. The plasma evolutions with time during and after the laser pulse irradiating the target are simulated numerically by using a three-dimensional difference scheme. And the numerical solutions of the impulse delivering from the plasma to the target are obtained. A comparison among the theoretical, numerical and experimental results and their analyses are performed. The experimental results are explained reasonably. The consistency between numerical results and experimental results implies that the numerical calculation model used in this paper can well describe the mechanical action of the laser on the target.

PM567-Doped solid dye lasers based on PMMA

Polymers are a kind of attractive hosts for laser dyes due to their high transparency in both pumping and lasing ranges and superior optical homogeneity. In this paper solid dye samples based on polymethyl methacrylate （PMMA） doped with different concentrations of 1, 3, 5, 7, 8 -pentamethyl-2, 6-diethylpyrromethene-BF2 （PM567） are prepared. The absorption, fluorescence and lasing spectra of the samples are obtained. Wide absorption and fluorescence bands are obtained and a red shift of the maxima of the lasing emission spectra is observed. With the second-harmonic generation of Q-switched Nd：YAC laser （532 nm, -20 ns） pumping the samples longitudinally, the slope efficiencies of the samples are obtained. There is an optimal dye concentration for the highest slope efficiency when the pumping energy is lower than some typical value （-250 mJ）, and the highest slope efficiency 35.6% is obtained in the sample with a dye concentration of 2 × 10^-4 mol/L. Pumping the samples at a rate of 10Hz with a pulse energy as high as 200 mJ （the fluence is 0.2 J/cm^2）, the output energy drops to one-half of its initial value after approximate 15500 pulses and the normalized photostability is 5.17CJ/mol. A kind of solid dye laser which could have some applications is built.

Infrared Laser Pumped Green and Blue Laser Emissions from a Single Solid State Material Doped by Rare Earth Ions

The possible ways and progress of infrared or red laser pumped green and blue laser emissions from a single solid state material doped by rare earth ions are outlined. The green and blue lasers realized from infrared laser pumped rare earth doped nonlinear laser crystals by means of self frequency conversion and from infrared laser pumped rare earth doped bulk, fiber and microsphere materials by means of frequency upconversion are introduced in detail. Other kinds of devices and methods are also compared. The typical nonlinear laser crystals such as YAl 3(BO 3) 4, GdAl 3(BO 3) 4, YCa 4O(BO 3) 3 , GdCa 4O(BO 3) 3, and the typical upconversion fluoride fibers are compared and analyzed. The major problems remaining to be solved and the developing trends in the area are also discussed.

An all-solid-state high power quasi-continuous-wave tunable dual-wavelength Ti：sapphire laser system using birefringence filter

This paper describes a tunable dual-wavelength Ti：sapphire laser system with quasi-continuous-wave and high-power outputs. In the design of the laser, it adopts a frequency-doubled Nd：YAG laser as the pumping source, and the birefringence filter as the tuning element. Tunable dual-wavelength outputs with one wavelength range from 700 nm to 756.5 nm, another from 830 nm to 900mn have been demonstrated. With a pump power of 23 W at 532 nm, a repetition rate of 7 kHz and a pulse width of 47.6 ns, an output power of 5.1 W at 744.8 nm and 860.9 nm with a pulse width of 13.2 ns and a line width of 3 nm has been obtained, it indicates an optical-to-optical conversion efficiency of 22.2%.

Absorption of ultrashort intense lasers in laser–solid interactions

With the advent of ultrashort high intensity laser pulses, laser absorption during the laser–solid interactions has received significant attention over the last two decades since it is related to a variety of applications of high intensity lasers,including the hot electron production for fast ignition of fusion targets, table-top bright X-ray and gamma-ray sources,ion acceleration, compact neutron sources, and generally the creation of high energy density matters. Normally, some absorption mechanisms found for nanosecond long laser pulses also appear for ultrashort laser pulses. The peculiar aspects with ultrashort laser pulses are that their absorption depends significantly on the preplasma condition and the initial target structures. Meanwhile, relativistic nonlinearity and ponderomotive force associated with the laser pulses lead to new mechanisms or phenomena, which are usually not found with nanosecond long pulses. In this paper, we present an overview of the recent progress on the major absorption mechanisms in intense laser–solid interactions, where emphasis is paid to our related theory and simulation studies.

Energy transfer in solid-state dye lasers based on methyl methacrylate co-doped with sulforhodamine B and crystal violet

Laser action in methyl methacrylate （MMA） co-doped with sulforhodamine B and crystal violet dyes was investi- gated. The dye mixture was incorporated into a solid polymeric matrix and was pumped by a 532-nm Nd：YAG laser. Distributed feedback dye laser （DFDL） action was induced in the dye mixture using a prism arrangement both in the donor and acceptor regions by an energy transfer mechanism. Theoretically, the characteristics of acceptor and donor DFDLs, and the dependence of their pulse widths and output powers on acceptor-donor concentrations and pump power, were studied. Experimentally, the output energy of DFDL was measured at the emission peaks of donor and acceptor dyes for different pump powers and different acceptor-donor concentrations. Tuning of the output wavelength was achieved by varying the period of the gain modulation of the laser medium. The laser wavelength showed continuous tunability from 563 nm to 648 nm.

Temperature Fluetuations in Laser-Solid Interaction

Epoxylite,polymethylmethacrylate and aluminum are irradiated by a cw CO2 laser and their temperature fluctuations are measured by the infrared thermal imagers. It is reported that the temperature fluctuation becomes stronger with increase of the laser-solid interaction time in the experiment, which is in good agreement with the theory prediction. Furthermore, the temperature fluctuation is experimentally studied while the material is melted or vaporized.

Stimulated Emission of Gamma Photon from Ultrashort Pulse Intense Laser—Solid—Target Interaction

The efficient production of energetic γ photons is a significant physical process in the relativistic ultrashortpulse laser-plasma inducing photonuclear action. Based on the interaction of laser-solid-target, an analytical theory onstimulated γ photon emission from a hot electron firing the target-nucleus is developed by a relativistic full quantummethod. The emitting power or probability of γ photon in arbitrary space direction can be calculated for laser irradiatingsolid-target normally. It is valid only if the scatter-centre is immovable or its motion can be neglected compared withthat of the scattered electrons.

Thermal Analysis of Blue Laser Diode for Solid State Lighting Application

Solid-state light sources based on laser diode are becoming great alternative for LEDs. Improvement of the thermal characteristics of InGaN LD is very important for realizing reliable devices. In this investigation the influence of the temperature of diode on light parameters was studied. White light was obtained by coupling blue light of diode with yellow phosphors: YAG:Ce3+ and GYAG:Ce3+ with nitride. For three values of the temperature of LD’s stem, regulated by Peltier module, CCT, CRI and chromaticity coordinates were measured by spectroradiometer. The importance of emission characteristics of materials was shown. Subsequently, the influence of temperature on laser diode intensity was investigated for 120 hours. This experiment was repeated for different levels of current and temperature. Finally, the steady state of thermal finite element analysis was performed to reveal the distribution of the temperature. The analysis showed the importance of heat sink and also temperature control.