A review on the multi-scaled structures and mechanical/thermal properties of tool steels fabricated by laser powder bed fusion additive manufacturing

The laser powder bed fusion(LPBF) process can integrally form geometrically complex and high-performance metallic parts that have attracted much interest,especially in the molds industry.The appearance of the LPBF makes it possible to design and produce complex conformal cooling channel systems in molds.Thus,LPBF-processed tool steels have attracted more and more attention.The complex thermal history in the LPBF process makes the microstructural characteristics and properties different from those of conventional manufactured tool steels.This paper provides an overview of LPBF-processed tool steels by describing the physical phenomena,the microstructural characteristics,and the mechanical/thermal properties,including tensile properties,wear resistance,and thermal properties.The microstructural characteristics are presented through a multiscale perspective,ranging from densification,meso-structure,microstructure,substructure in grains,to nanoprecipitates.Finally,a summary of tool steels and their challenges and outlooks are introduced.

Microstructure and Properties of Low Temperature Composite Chromized Layer on H13 Tool Steel

Low temperature composite chromizing is a process composed of a plain ion-carbonitriding or ion-nitriding at 550-580℃, followed by a low-temperature chromizing in a salt-bath of 590℃. The microstructure and properties of the low temperature composite chromized layer on H13 tool steel were investigated using metallography, X-ray diffraction, microanalysis, hardness and wear tests. It was found that this low temperature process was thermo-dynamically and kinetically possible, and the composite chromized layer on H13 steel, with a thickness of 3-6 μm, consisted of three sub-layers (bands), viz. the outer Cr-rich one, the intermediate (black) one, and the inner, original white layer. After chromizing, the former diffusion layer was thickened. The results of X-ray diffraction showed that the composite chromized layer contained such nitrides and carbides of chromium as CrN, Cr2N, (Cr, Fe)23C6, and (Cr, Fe)7C3, as well as plain α-(Fe, Cr). A high surface microhardness of 1450-1550 HV0.025, which is much higher than that obtained by the conventional ion carbonitriding and ion nitriding, was obtained. In addition, an excellent wear resistance was gained on the composite chromized layer.

Effect of inclusion size on the high cycle fatigue strength and failure mode of a high V alloyed powder metallurgy tool steel

The fatigue strength of a high V alloyed powder metallurgy tool steel with two different inclusion size levels, tempered at different temperatures, was investigated by a series of high cycle fatigue tests. It was shown that brittle inclusions with large sizes above 30μm prompted the occurrence of subsurface crack initiation and the reduction in fatigue strength. The fracture toughness and the stress amplitude both exerted a significant influence on the fish-eye size. A larger fish-eye area would form in the sample with a higher fracture toughness subjected to a lower stress amplitude. The stress intensity factor of the inclusion was found to lie above a typical value of the threshold stress intensity factor of 4 MPa.m^1/2. The fracture toughness of the sample with a hardness above HRC 56 could be estimated by the mean value of the stress intensity factor of the fish-eye. According to fractographic evaluation, the critical inclusion size can be calculated by linear fracture mechanics.

Microstructural evolution of a heat-treated H23 tool steel

The microstructure and the stability of carbides after heat treatments in an H23 tool steel were investigated. The heat treatments consisted of austenization at two different austenizing temperatures （1100℃ and 1250℃）, followed by water quenching and double-aging at 650℃, 750℃, and 800℃with air cooling between the first and second aging treatments. Martensite did not form in the as-quenched micro- structures, which consisted of a ferrite matrix, M6C, M7C3, and MC carbides. The double-aged microstructures consisted of a ferrite matrix and MC, M6C, M7C3, and M23C6 carbides. Secondary hardening as a consequence of secondary precipitation of fine M2C carbides did not occur. There was disagreement between the experimental microstructure and the results of thermodynamic calculations. The highest double-aged hardness of the H23 tool steel was 448 HV after austenization at 1250℃ and double-aging at 650℃, which suggested that this tool steel should be used at temperatures below 650℃.

Effect of deep cryogenic treatment on the formation of nano-sized carbides and the wear behavior of D2 tool steel

The effect of deep cryogenic treatment on the microstructure, hardness, and wear behavior of D2 tool steel was studied by scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, X-ray diffraction （XRD）, hardness test, pin-on-disk wear test, and the reciprocating pin-on-fiat wear test. The results show that deep cryogenic treatment eliminates retained austenite, makes a better carbide distribution, and increases the carbide content. Furthermore, some new nano-sized carbides form during the deep cryogenic treatment, thereby increasing the hardness and improving the wear behavior of the samples.

Effect of deep cryogenic treatment on the properties of 80CrMo12 5 tool steel

The effect of deep cryogenic treatment on the mechanical properties of 80CrMo 12 5 tool steel was investigated. Moreover, the effects of stabilization （holding at room temperature for some periods before deep cryogenic treatment） and tempering before deep cryogenic treatment were studied. The results show that deep cryogenic treatment can eliminate the retained austenite, making a better carbide distribu- tion and a higher carbide amount. As a result, a remarkable improvement in wear resistance of cryogenically treated specimens is observed. Moreover, the ultimate tensile strength increases, and the toughness of the sample decreases. It is also found that both stabilization and tem- pering before deep cryogenic treatment decrease the wear resistance, hardness, and carbides homogeneity compared to the deep cryogeni- cally treated samples. It is concluded that deep cryogenic treatment should be performed without any delay on samples after quenching to reach the highest wear resistance and hardness.

Repair Effect of Hot Work Tool Steel by Laser-Melting Process

Both wear and crack due to heat checking in hot work tool steel are major failure modes.It is desirable to find amethod to lengthen the tool life while reducing manufacturing cost.This paper suggests a method to improve toollife for hot work tool steel(SKD6)with crack by laser-melting process.The method has been evaluated using theimpact and fatigue test results.It is demonstrated that a repair of the crack by a laser-melting process is effectivefor life extension of the damaged tool.

Mechanism of generation of large(Ti,Nb,V)(C,N)-type precipitates in H13 + Nb tool steel

The characteristics and generation mechanism of（Ti,Nb,V）（C,N） precipitates larger than 2 μm in Nb-containing H13 bar steel were studied. The results show that two types of（Ti,Nb,V）（C,N） phases exist—a Ti-V-rich one and an Nb-rich one—in the form of single or complex precipitates. The sizes of the single Ti-V-rich（Ti,Nb,V）（C,N） precipitates are mostly within 5 to 10 μm, whereas the sizes of the single Nb-rich precipitates are mostly 2–5 μm. The complex precipitates are larger and contain an inner Ti-V-rich layer and an outer Nb-rich layer. The compositional distribution of（Ti,Nb,V）（C,N） is concentrated. The average composition of the single Ti-V-rich phase is（Ti_（0.511）V_（0.356）Nb_（0.133））（CxNy）, whereas that for the single Nb-rich phase is（Ti_（0.061）V_（0.263）Nb_（0.676））（C_xN_y）. The calculation results based on the Scheil–Gulliver model in the Thermo-Calc software combining with the thermal stability experiments show that the large phases precipitate during the solidification process. With the development of solidification, the Ti-V-rich phase precipitates first and becomes homogeneous during the subsequent temperature reduction and heat treatment processes. The Nb-rich phase appears later.

Effect of inclusion on high cycle fatigue response of a powder metallurgy tool steel

The high cycle fatigue response of a high V-alloyed powder metallurgy tool steel （AISI 11） with different inclusion sizes was studied. Two materials of this grade at a similar hardness of about HRC 60 were subjected to axial loading fatigue tests, tensile tests and fracture toughness measurements to investigate their mechanical properties. Large inclusion above 70 ~rn is indicated to be responsible for the tensile fracture which happens before yielding. The fatigue strength obtained up to 107 cycles is found to decrease from approximately 1 538 MPa to 1000 MPa with the inclusion size increasing above 30 Izm. The internally induced crack initiation is mainly attributed to the surface compressive residual stress of 300-450 MPa. Fractographic evaluation demonstrates that the crack initiation and propagation controlling factors of the two materials are almost the same, indicating that the two factors would be insignificantly affected by the inclusion size level. Paris sizes of the two materials both show a tendency to decrease as the ratio of stress intensity factor of crack origin to factor of fish-eye increases. The investigation into the relationship between stress intensity factors and fatigue life of the two materials further indicates that the high cycle fatigue behavior of AISI 11 is controlled by crack propagation.

Deoxidation of H13 tool steel with CaF_(2)-MgO-CaO-Al_(2)O_(3)-SiO_(2) slags at 1873 K

Laboratory-scale experiments were performed to investigate the deoxidation of H13 tool steel with CaF_(2)-MgO-Al_(2)O_(3)-CaO-SiO_(2) slags at 1873 K.The calculation of thermodynamics and kinetics was also verified through the experimental results.The results show that[Si]-[O]reaction is the control reaction,and with the increase of basicity of slag,the limitation of deoxidation was decreased.The limitation of deoxidation is the lowest for the slag with basicity of 2.0.Under the conditions of the basicity of 2.0 and the content of CaF_(2) more than 50%,the limitation of deoxidation is less than 10×10^(−6),and it does not depend on the contents of Al_(2)O_(3) and CaF_(2) in slags.The mass transport of oxygen in the metal phase is the rate-controlling step,and the slag composition has no effect on the equilibrium time of deoxidation.Based on this finding,the optimized slag composition is designed and it contains the following components:51.5%CaF_(2),20.3%MgO,16.2%Al_(2)O_(3),8.2%CaO and 3.8%SiO_(2).In the case of the optimized deoxidizing slag,the total oxygen content in H13 steel can be reduced from 25×10^(−6) to 6×10^(−6).

C-Curves of Tool Steels for Annealing and Their Application

TTT diagrams,CCT diagrams and critical points of steels H13,S7,S5 for annealing were measured and investigated by means of Formastor-Digital full-automatic phase transformation dilatometer in order to make their annealing technology reasonable and scientific.The basis is provided for making a new annealing technology scientifically.The new technology improves the quality of annealed materials,saves energy and increases productivity.

MICROSTRUCTURE OF LASER MELTED-RESOLIDIFIED LAYER ON HIGH SPEED TOOL STEEL

The laser melted-resolidified processing on W18Cr4V high speed tool steel has been made us- ing a 1 kW CO_2 continuous wave laser device.The microstructure of the laser melted- resolidified layer has been examined by optical microscopy and transmission electron microscopy(TEM).It was characteristic of extremely fine dendrite in the laser melted- resolidified layer and δ-ferrite in bulk form in the center of dendrite.The predominant twin martensite and a little dislocation martensite existed in the dendrite.The thin plate-like M_(213)C_6 carbide precipitated coherently on the twin martensites along their twin plane.There were both austenite rich in W,V and Cr and M_6C carbide in the interdendritic regions.

FLOW STRESS MODEL FOR HARD MACHINING OF AISI H13 WORK TOOL STEEL

An approach is presented to characterize the stress response of workpiece in hard machining, accounted for the effect of the initial workpiece hardness, temperature, strain and strain rate on flow stress. AISI H13 work tool steel was chosen to verify this methodology. The proposed flow stress model demonstrates a good agreement with data collected from published experiments. Therefore, the proposed model can be used to predict the corresponding flow stress-strain response of AISI H13 work tool steel with variation of the initial workpiece hardness in hard machining.

Calculation of the Hardness Space Distribution in the As Quenched Condition of a Medium Hardening Tool Steel

The calculation of the hardness profile is a powerful tool for the selection of the right steel for a given purpose. Computer programs INC-PHATRAN and INDUCTER-B were formerly developed by the authors for the calculation of hardness profiles after heat treatment processes of low alloy and carbon steels. The first one simulates quenching as well as through hardening operations, and the second one models electromagnetic induction heat treatments processes. These codes make use of the SAE Standard 3406 in order to obtain the hardness profile, with enhanced regression coefficients recently obtained by the authors. The present work broadens the field of application of this method, allowing to apply it for low hardenability tool steels such as the ASTM O1 Tool Steel. The method used for the calculation of the hardness profile is here summarized, and an example of application is described, which shows good correspondence between the calculated and measured values.

Experimental Study on Material Surface Modification of Tool Steel

This paper presents the surface temperature behavior of M42 high-speed tool steel samples during N+ implantation in an industrialized GLZ-100 metal-ion implantation machine. A detail study has been made on the parameters of N+ implantation. Optimized technical parameters have been presented. The microhardness of the sample surface implanted under these parameters has been increased by a factor of 2.3, and the wear-resistance has been improved by about 5.4 times. The research on the mechanism of surface modification of M42 steel by nitrogen ion implantation has also been made.

Laser surface hardening of AISI H13 tool steel

An attempt was made to improve the surface hardness and wear properties of AISI H13 tool steel through solid solution hardening and refinement of microstructures using a 200 W fiber laser as a heat generating source.The hardness of laser melted zone was investigated.In order to identify the effect of heat input on the laser melting zone,scanning conditions were controlled.The results show that,the hardness of as-received AISI H13 tool steel is approximately Hv 240,and the hardness after laser surface heat treatment is around Hv 480-510.The hardening depth and width are increased with the increase in the heat input applied.Application of experimental results will be considered in tooling industry.

Study on Interface Structure and Bond Properties between Cemented Carbide and Tool Steel Blazing with amorphous alloy

Cemented Carbide YG11C and Tool Steel Crl2MoV was blazed with Ni-base amorphous alloys, QG-1011, MBF-20 and MBF-75, using dynamics thermodynamics analogue testing machine Gleeble 1500D. The effects of brazing temperature, holding time and holding pressure on micro-structure and bond strength were investigated. Results showed that YG11C and Crl2MoV were all wetted well by these three Ni-base alloys, and the bond strength was as high as 220MPa, 320MPa, 320MPa respectively. When the blazing temperature was at the point over the melting point 60-70°C of Ni-base alloy, the holding time was about 2-10min, the suitable pressure was benefit for improving the brazing quality. Microanalysis showed Co in cemented carbide diffused into liquid brazing alloy and formed the Fe-Co solid .solution.

Selective laser melting of Fe-Ni-Cr layer on AISI H13 tool steel

An attempt to fabricate Fe-Ni-Cr coating on AISI H13 tool steel was performed with selective laser melting.Fe-Ni-Cr coating was produced by experimental facilities consisting of a 200 W fiber laser which can be focused to 80 μm and atmospheric chamber which can control atmospheric pressure with N2 or Ar.Coating layer was fabricated with various process parameters such as laser power,scan rate and fill spacing.Surface quality and coating thickness were measured and analyzed.Three different surface patterns,such as typeⅠ,typeⅡand type Ⅲ,are shown with various test conditions and smooth regular pattern is obtained under the conditions as 10 μm of fill spacing,50-350 mm/s of scan rate and 40 μm of fill spacing,10-150 mm/s of scan rate.The maximum coating thickness is increased with power elevation or scan rate drop,and average thickness of 10 μm fill spacing is lower than that of 40 μm fill spacing.

Erosion problem in tool steel using cold box core-making process

This paper presents the erosion results of the AISI H13 steel impinged by resin-bonded silica sand, using a testing rig that closely simulates the real blowing conditions during industrial core-making. Steel specimens were heat treated to obtain hardness of 294, 445 and 595 HV200 (29, 45 and 55 HRC). Erosion tests were carried out at impingement angles from 20° to 90° and air drag pressures of 1.38, 2.07 and 2.76 bar (20, 30 and 40 psi). The main results are summarized as follows:(i) The harder material, the lower erosion;(ii) the maximum erosion rate is at 30°;(iii) Little difference in erosion rate at impact angle of 60° and 90° for a constant pressure tested regardless of the hardness level;(iv) As the pressure increases, so does the erosion rate, being more sensitive for low impact angles. Finally, a differential form of the general erosion equation is applied on a practical core-making case to evaluate the erosion rate of the H13 steel at 30° and 90° impingement angles.

The Influence of Method of Carburizing and Nitrocarburizing on the Microstructure and Properties of Tool Steels.

The paper presents the results of wear and metallography tests of tool steel grades: ASTM A681, Chl2M and CH12FS per COST, AMS 6437E i BS X46Crl3, all surface hardened by the Carbo process (carburizing) and by the NiCar process (nitrocarburizing). The thermo-chemical treatment was conducted in powder pack for a duration of 6 h (carburizing) and for 4 h in the case of nitrocarburizing. Factors investigated were: morphology, depth and microhardness of the cases obtained, their microstructure, as well as phase composition. Wear tests were conducted by the three cylinder-cone method. Wear velocity was 0.58 m/s, unit load was 50 MPa and 400Mpa, wear path was 3470 m. Oil SAE30 was applied at the rate of 30 drops per minute.