Ensuring adequate access to truck parking is critical to the safe and efficient movement of freight traffic. There are strict federal guidelines for commercial truck driver rest periods. Rest areas and private truck s...Ensuring adequate access to truck parking is critical to the safe and efficient movement of freight traffic. There are strict federal guidelines for commercial truck driver rest periods. Rest areas and private truck stops are the only places for the trucks to stop legally and safely. In locations without sufficient parking areas, trucks often park on interstate ramps, which create safety risks for other interstate motorists. Historically, agencies have employed costly and time intensive manual counting methods, camera surveillance, and driver surveys to assess truck parking. Connected truck data, available in near real-time, offers an efficient alternative to practitioners to assess truck parking patterns and identify areas where there may be insufficient safe parking spaces. This paper presents a case study of interstate I-70 in east central Indiana and documents the observed spatiotemporal impacts of a rest area closure on truck parking on nearby interstate ramps. Results showed that there was a 28% increase in parking on ramps during the rest area closure. Analysis also found that ramps closest to the rest area were most impacted by the closure, seeing a rise in truck parking sessions as high as 2.7 times. Parking duration on the ramps during rest area closure also increased drastically. Although it was expected that this would result in increased parking by trucks on adjacent ramps, this before, during, after scenario provided an ideal scenario to evaluate the robustness of these techniques to assess changing parking characteristics of long-haul commercial trucks. The data analytics and visualization tools presented in this study are scalable nationwide and will aid stakeholders in informed data-driven decision making when allocating resources towards improving the nations commercial vehicle parking infrastructure.展开更多
In this paper,two lifting mechanism models with opposing placements,which use the same hydraulic hoist model and have the same angle of 50°,have been developed.The mechanical and hydraulic simulation models are e...In this paper,two lifting mechanism models with opposing placements,which use the same hydraulic hoist model and have the same angle of 50°,have been developed.The mechanical and hydraulic simulation models are established using MATLAB Simscape to analyze their kinetics and dynamics in the lifting and holding stages.The simulation findings are compared to the analytical calculation results in the steady state,and both methods show good agreement.In the early lifting stage,Model 1 produces greater force and discharges goods in the container faster than Model 2.Meanwhile,Model 2 reaches a higher force and ejects goods from the container cleaner than its counterpart at the end lifting stage.The established simulation models can consider the effects of dynamic loads due to inertial moments and forces generated during the system operation.It is crucial in studying,designing,and optimizing the structure of hydraulic-mechanical systems.展开更多
The plug-in hybrid vehicles(PHEV)technology can effectively address the issues of poor dynamics and higher energy consumption commonly found in traditional mining dump trucks.Meanwhile,plug-in hybrid electric trucks c...The plug-in hybrid vehicles(PHEV)technology can effectively address the issues of poor dynamics and higher energy consumption commonly found in traditional mining dump trucks.Meanwhile,plug-in hybrid electric trucks can achieve excellent fuel economy through efficient energy management strategies(EMS).Therefore,a series hybrid system is constructed based on a 100-ton mining dump truck in this paper.And inspired by the dynamic programming(DP)algorithm,a predictive equivalent consumption minimization strategy(P-ECMS)based on the DP optimization result is proposed.Based on the optimal control manifold and the SOC reference trajectory obtained by the DP algorithm,the P-ECMS strategy performs real-time stage parameter optimization to obtain the optimal equivalent factor(EF).Finally,applying the equivalent consumption minimization strategy(ECMS)realizes real-time control.The simulation results show that the equivalent fuel consumption of the P-ECMS strategy under the experimentally collected mining cycle conditions is 150.8 L/100 km,which is 10.9%less than that of the common CDCS strategy(169.3 L/100 km),and achieves 99.47%of the fuel saving effect of the DP strategy(150 L/100 km).展开更多
Intermodal competition changes with changes in technology, economics, and environmental concerns. Trucks and airships are generally considered not to be competitors, but this depends on the distance of haul. The tonne...Intermodal competition changes with changes in technology, economics, and environmental concerns. Trucks and airships are generally considered not to be competitors, but this depends on the distance of haul. The tonne-kilometer cost of trucking rises much more quickly with distance than it does the cost of a cargo airship. At some distance, the two modes are direct substitutes. The costs of the Mexico-Canada refrigerated truck supply chain are compared with the costs of a 100t-lift, electrically-powered airship. The flight characteristics of the Hindenburg Zeppelin are used as a model for a modern cargo airship. The supply chain cost of trucking tomatoes is used to test the theorical proposition. The cost difference works out to about US10¢/kg (5¢/lb) advantage for trucking Mexican tomatoes to Canada. However, this cost disadvantage of the airship could be made up by their vibrationless ride, better air circulation and one-day service versus four days by truck. This alternative form of transportation could have a positive impact on worldwide north-south distribution of food. Airships can overcome trade barriers and distance to open new markets for perishable food exports. In addition, they would reduce the carbon emissions of transport. Canada imports 160,000 refrigerated truckloads of fruits and vegetables by from the southern US and Mexico. With an average driving distance of 3,000 km, these trucks emit 606,000 MT of CO<sub>2</sub> annually. Airships powered by hydrogen fuel cells would have zero-carbon emissions. Markets are not yet incorporating the environmental advantage of airships in any freight comparison, but inevitably this will be important.展开更多
Introduction: Over-drowsiness is a condition with serious consequences, including road accidents. The condition, however, is often ignored both by carers as well as victims themselves. The aim of the present study was...Introduction: Over-drowsiness is a condition with serious consequences, including road accidents. The condition, however, is often ignored both by carers as well as victims themselves. The aim of the present study was to investigate the factors associated with excessive drowsiness in Cotonou, Benin 2023, along with its influence on the occurrence of crashes among truck drivers. Methods: This was a descriptive and analytical cross-sectional study, held from March 13 to April 10, 2023, focusing on large truck drivers over 18 years of age, selected by convenience from parking lots in and around the city of Cotonou. Data collected using questionnaires on socio-demographic and behavioral factors, sleeping habits and working conditions were processed using Stata 15.0 software. Excessive drowsiness was defined by a score above 10 on the Epworth scale. Associated factors were found by multiple logistic regression, at a threshold of 0.05. Results: Altogether 304 drivers, all male and aged 35.98 ± 8.42 years, were surveyed. The prevalence of excessive drowsiness was 29.2%. The associated factors identified were not practicing sport OR = 2.27, CI95% = [1.33;3.86], p = 0,002;sleep duration per working day OR = 1.82;CI95% = [1.06;3.11], p = 0,027 and average distance travelled per day OR = 3.40;CI95% = [1.53;7.56], p = 0,003. Excessive drowsiness was associated with a 1.73-fold increased risk of road accidents (CI95% [1.04;2.87];p = 0.03). Conclusion: Communicating excessive drowsiness and its associated factors to all the stakeholders in the haulage chain is essential to help prevent road accidents.展开更多
In-cab alerts warn commercial vehicle drivers of upcoming roadway incidents, slowdowns and work zone construction activities. This paper reports on a study evaluating the driver response to in-cab alerts in Ohio. Driv...In-cab alerts warn commercial vehicle drivers of upcoming roadway incidents, slowdowns and work zone construction activities. This paper reports on a study evaluating the driver response to in-cab alerts in Ohio. Driver response was evaluated by measuring the statistical trends of vehicle speeds after the in-cab alerts were received. Vehicle speeds pre and post in-cab alert were collected over a 47 day period in the fall of 2023 for trucks traveling on interstate roadways in Ohio. Results show that approximately 22% of drivers receiving Dangerous Slowdown alerts had reduced their speeds by at least 5 mph 30 seconds after receiving such an alert. Segmenting this analysis by speed found that of vehicles traveling at or above 70 mph at the time of alerting, 26% reduced speeds by at least 5 mph. These speed reductions suggest drivers taking actional measures after receiving alerts. Future studies will involve further analysis on the impact of the types of alerts shown, roadway characteristics and overall traffic conditions on truck speeds passing through work zones.展开更多
The prevalence of human immunodeficiency virus (AIDS) and hepatitis B virus among heavy truck drivers and their assistants has been well documented globally in correlation with their behavioral characteristics. The pr...The prevalence of human immunodeficiency virus (AIDS) and hepatitis B virus among heavy truck drivers and their assistants has been well documented globally in correlation with their behavioral characteristics. The present study aimed to screen for human immunodeficiency virus (HIV), hepatitis B virus (HBV), and behavioral characteristics among heavy truck drivers in Port Sudan. A cross-sectional study was conducted on 274 heavy truck drivers and their assistants who used the highway Port Sudan-Khartoum in Port Sudan city during 2019-2021. Data on behavioral characteristics and substance use habits were collected using a structured questionnaire, and an ELISA test was used to screen for HIV and HBV infections in the study participants. The chi-square test, odds ratio, and confidence intervals were used to find the association between behavioral characteristics and seropositive HIV/HBV. Of the 274 enrolled participants, the seroprevalence rates of HIV were 2.7% and HBV was 23.7%. Ninety-four (34.3%) of them had a history of high-risk sexual behavior outside of marriage;only two (0.7%) used condoms;14.2% of participants reported alcohol use;and 1.1% reported drug use. Univariate analysis revealed that having a sex history outside of marriage with ≥1 sex partner and never using a condom with a spouse or casual partner were significant risk factors for HIV and HBV among drivers. Fortunately, we found that most of the drivers reported low alcohol and drug use. Concerning this study, the seroprevalence of HIV and HBV is highly associated with a history of having sex outside of marriage and sexual behavior among truck drivers and assistances. Additional studies are needed to further investigate other STIs and behavioral characteristics associated with factors in truck drivers/assistance in different truck stop regions in Sudan.展开更多
Truck frames should be designed and fabricated with enough rigidity to avoid excessive deflections. Finite element analysis (FEA) plays an important role in all stages of frame designs. While being accurate, 3D solid ...Truck frames should be designed and fabricated with enough rigidity to avoid excessive deflections. Finite element analysis (FEA) plays an important role in all stages of frame designs. While being accurate, 3D solid element FEA models are built upon frame configuration details which are not feasible in the preliminary design stage, partially because of limited available design data of frames and heavy computation costs. This research develops 1D beam element FEA models for simulating frame structures. In this paper, the CAD model of a truck frame is first created. The solid element FEA analysis, which is adopted as the baseline in this study, is subsequently conducted for the stiffness of the frame, Next, beam element FEA analysis is performed for validating the feasibility of the beam element FEA model by comparing the results from the solid and beam element FEA models. It is found that the beam element FEA model can predict the frame stiffness with acceptable accuracy and reduce the computation cost significantly.展开更多
This study demonstrates a practical cycle time analysis of dump truck haulage system of “Ukhaa Khudag” open-pit coal mine located in Umnugobi Province, Mongolia. It examines the possibility of minimizing the cycle t...This study demonstrates a practical cycle time analysis of dump truck haulage system of “Ukhaa Khudag” open-pit coal mine located in Umnugobi Province, Mongolia. It examines the possibility of minimizing the cycle time of the haulage system as well as factors impacting the speed of the dump truck. The current study divides the open pit mine road for the dump trucks into five sections which are bench road, ramp, surface road, dump road uphill, and dump road. Meanwhile, it investigates the influence of the length, the grade, and the rolling resistance of the road section on the cycle time. The data is analyzed using mathematical regression methods via Microsoft Excel program. For each of the five road sections, we compare the statistical calculations of three regression models: linear, quadratic and exponential;thus, a total of thirty regression models are obtained in this research. Accordingly, the cycle time for each road section is predicted by the most accountable model. The loaded and empty direction of the movement is measured and calculated for each road section, and it appears that the difference between the calculated mean value and the actual cycle time of the models is 0.82 seconds with a relative error of 2.51 percent.展开更多
In order to improve the maintenance efficiency,extend the use time,ensure that the exhaust emission meets the standard,forthe 830E truck heating bucket exhaust pipe design defects,the current single smoke exhaust syst...In order to improve the maintenance efficiency,extend the use time,ensure that the exhaust emission meets the standard,forthe 830E truck heating bucket exhaust pipe design defects,the current single smoke exhaust system is transformed into atime period,convertible smoke exhaust system.After the transformation,it can not only realize the side row to prevent direct corrosion of the box bucket in summer,but also realize the heating of the box bucket at low temperature in winter to prevent snow and ice and frozen blocks from sticking to the box bucket and the materials transported.After the transformation can save a lot of manpower,material resources,financial resources,improve the service life.展开更多
In 2016 alone, around 4000 people died in crashes involving trucks in the USA, with 21% of these fatalities involving only single-unit trucks. Much research has identified the underlying factors for truck crashes.Howe...In 2016 alone, around 4000 people died in crashes involving trucks in the USA, with 21% of these fatalities involving only single-unit trucks. Much research has identified the underlying factors for truck crashes.However, few studies detected the factors unique to single and multiple crashes, and none have examined these underlying factors to severe truck crashes in conjunction with violation data. The current research assessed all of these factors using two approaches to improve truck safety.The first approach used ordinal logistic regression to investigate the contributory factors that increased the odds of severe single-truck and multiple-vehicle crashes, with involvement of at least one truck. The literature has indicated that past violations can be used to predict future violations and crashes. Therefore, the second approach used risky violations, related to truck crashes, to identify the contributory factors to the risky violations and truck crashes. Driver actions of failure to keep proper lane following too close and driving too fast for conditions accounted for about 40% of all the truck crashes. Therefore, the same violations as the aforementioned driver actions were included in the analysis. Based on ordinal logistic regression, the analysis for the first approach indicated that being under non-normal conditions at the time of crash, driving on dry-road condition and having a distraction in the cabin are some of the factors that increase the odds of severe single-truck crashes. On the other hand,speed compliance, alcohol involvement, and posted speed limits are some of the variables that impacted the severity of multiple-vehicle, truck-involved crashes. With the second approach, the violations related to risky driver actions,which were underlying causes of severe truck crashes, were identified and analysis was run to identify the groups at increased risk of truck-involved crashes. The results of violations indicated that being nonresident, driving offpeak hours, and driving on weekends could increase the risk of truck-involved crashes. This paper offers an insight into the capability of using violation data, in addition to crash data, in identification of possible countermeasures to reduce crash frequency.展开更多
Roundabouts in United States and other countries have been proved to be very successful, effective, and a safe traffic control treatment. Roundabouts in the context of regularly expected truck configuration have also ...Roundabouts in United States and other countries have been proved to be very successful, effective, and a safe traffic control treatment. Roundabouts in the context of regularly expected truck configuration have also been successful for effective roundabout designs;however, there are always some site specific issues for trucks accommodation at roundabouts. Therefore, there is a great need for an informational guide in the form of synthesis report for roundabout designs specific to unique trucking traffic activity. While there are not significant literatures and studies in this subject, there are few studies/reports spread out which address various issues in this subject area. This study attempts to synthesize the research and knowledge of truck accommodation at roundabouts by synthesizing various research studies, reports, and articles;various subject areas such as roundabout designs for trucking activity, roundabout designs and accommodation strategies for specialized trucking activity such as oversized trucks, truck safety at roundabouts, and motor carrier perspective of trucking at roundabouts have been analyzed and relevant knowledge has been synthesized. This synthesis can be useful o researchers, designers, planners, and decision makers to determine effective ways to address specific trucking related issues at a roundabout.展开更多
Di erential braking and active steering have already been integrated to overcome their shortcomings. However, existing research mainly focuses on two-axle vehicles and controllers are mostly designed to use one contro...Di erential braking and active steering have already been integrated to overcome their shortcomings. However, existing research mainly focuses on two-axle vehicles and controllers are mostly designed to use one control method to improve the other. Moreover, many experiments are needed to improve the robustness; therefore, these control methods are underutilized. This paper proposes an integrated control system specially designed for multi-axle vehicles, in which the desired lateral force and yaw moment of vehicles are determined by the sliding mode control algorithm. The output of the sliding mode control is distributed to the suitable wheels based on the abilities and potentials of the two control methods. Moreover, in this method, fewer experiments are needed, and the robustness and simultaneity are both guaranteed. To simplify the optimization system and to improve the computation speed, seven simple optimization subsystems are designed for the determination of control outputs on each wheel. The simulation results show that the proposed controller obviously enhances the stability of multi-axle trucks. The system improves 68% of the safe velocity, and its performance is much better than both di erential braking and active steering. This research proposes an integrated control system that can simultaneously invoke di erential braking and active steering of multi-axle vehicles to fully utilize the abilities and potentials of the two control methods.展开更多
The requirements of vehicle dynamic stability control are higher than ever as the significant increase of electric drive articulated vehicle speed. According to the construction features of articulated dumping truck a...The requirements of vehicle dynamic stability control are higher than ever as the significant increase of electric drive articulated vehicle speed. According to the construction features of articulated dumping truck and nonlinear characteristics of moving vehicles,nonlinear observer of vehicle status is designed to strength robustness of dynamic control system in this paper. A 4-degree-of-freedom nonlinear dynamic model of articulated electric drive vehicle is built as reference model to estimate the state of the articulated vehicle. And by adopting Unscented Kalman Filter( UKF) algorithm,a series of state parameters such as longitudinal velocities of front and rear frames,yaw rate and side-slip angle are estimated. During the test of 60 t articulated electric drive vehicle,2 inertial navigation modules are installed in the front frame and rear frame respectively and the speed of each electric drive wheel is obtained simultaneously. As the test results suggest,in various working conditions,the algorithm based on UKF is able to accurately estimate the state parameters of articulated vehicle with the estimated error less than 5%. The proposed method is justified to be the theoretical basis and application guidance for articulated vehicle stability control.展开更多
In a global environment where energy and labor are becoming increasingly expensive, continuous mining systems such as In-Pit Crushing and Conveying(IPCC) systems have been advanced as offering a real alternative to co...In a global environment where energy and labor are becoming increasingly expensive, continuous mining systems such as In-Pit Crushing and Conveying(IPCC) systems have been advanced as offering a real alternative to conventional truck haulage systems. The implementation of IPCC systems in hard rock operations in open pit mines however requires different and more comprehensive planning approaches in order to adequately reflect the practical aspects associated with these. This paper investigates the impact that these approaches may have on the implementation of IPCC systems on a basic metalliferous deposit amenable to open pit exploitation. A strategic life of mine plan to provide numerous economic indicators for each approach is analyzed and compared to traditional truck haulage systems. The mine planning and evaluation process highlights the increased overall resource recovery that may accompany the use of IPCC systems. This investigation also provides insights into the issues associated with IPCC and the scale and type of operation and orebody that is likely to provide a feasible alternative to truck haulage.展开更多
It is very necessary for an intelligent heavy truck to have the ability to prevent rollover independently.However,it was rarely considered in intelligent vehicle motion planning.To improve rollover stability,a motion ...It is very necessary for an intelligent heavy truck to have the ability to prevent rollover independently.However,it was rarely considered in intelligent vehicle motion planning.To improve rollover stability,a motion planning strategy with autonomous anti rollover ability for an intelligent heavy truck is put forward in this paper.Considering the influence of unsprung mass in the front axle and the rear axle and the body roll stiffness on vehicle rollover stability,a rollover dynamics model is built for the intelligent heavy truck.From the model,a novel rollover index is derived to evaluate vehicle rollover risk accurately,and a model predictive control algorithm is applicated to design the motion planning strategy for the intelligent heavy truck,which integrates the vehicle rollover stability,the artificial potential field for the obstacle avoidance,the path tracking and vehicle dynamics constrains.Then,the optimal path is obtained to meet the requirements that the intelligent heavy truck can avoid obstacles and drive stably without rollover.In addition,three typical scenarios are designed to numerically simulate the dynamic performance of the intelligent heavy truck.The results show that the proposed motion planning strategy can avoid collisions and improve vehicle rollover stability effectively even under the worst driving scenarios.展开更多
文摘Ensuring adequate access to truck parking is critical to the safe and efficient movement of freight traffic. There are strict federal guidelines for commercial truck driver rest periods. Rest areas and private truck stops are the only places for the trucks to stop legally and safely. In locations without sufficient parking areas, trucks often park on interstate ramps, which create safety risks for other interstate motorists. Historically, agencies have employed costly and time intensive manual counting methods, camera surveillance, and driver surveys to assess truck parking. Connected truck data, available in near real-time, offers an efficient alternative to practitioners to assess truck parking patterns and identify areas where there may be insufficient safe parking spaces. This paper presents a case study of interstate I-70 in east central Indiana and documents the observed spatiotemporal impacts of a rest area closure on truck parking on nearby interstate ramps. Results showed that there was a 28% increase in parking on ramps during the rest area closure. Analysis also found that ramps closest to the rest area were most impacted by the closure, seeing a rise in truck parking sessions as high as 2.7 times. Parking duration on the ramps during rest area closure also increased drastically. Although it was expected that this would result in increased parking by trucks on adjacent ramps, this before, during, after scenario provided an ideal scenario to evaluate the robustness of these techniques to assess changing parking characteristics of long-haul commercial trucks. The data analytics and visualization tools presented in this study are scalable nationwide and will aid stakeholders in informed data-driven decision making when allocating resources towards improving the nations commercial vehicle parking infrastructure.
基金Ho Chi Minh City University of Technology(HCMUT)Vietnam National University Ho Chi Minh City(VNU-HCM)for supporting this study。
文摘In this paper,two lifting mechanism models with opposing placements,which use the same hydraulic hoist model and have the same angle of 50°,have been developed.The mechanical and hydraulic simulation models are established using MATLAB Simscape to analyze their kinetics and dynamics in the lifting and holding stages.The simulation findings are compared to the analytical calculation results in the steady state,and both methods show good agreement.In the early lifting stage,Model 1 produces greater force and discharges goods in the container faster than Model 2.Meanwhile,Model 2 reaches a higher force and ejects goods from the container cleaner than its counterpart at the end lifting stage.The established simulation models can consider the effects of dynamic loads due to inertial moments and forces generated during the system operation.It is crucial in studying,designing,and optimizing the structure of hydraulic-mechanical systems.
文摘The plug-in hybrid vehicles(PHEV)technology can effectively address the issues of poor dynamics and higher energy consumption commonly found in traditional mining dump trucks.Meanwhile,plug-in hybrid electric trucks can achieve excellent fuel economy through efficient energy management strategies(EMS).Therefore,a series hybrid system is constructed based on a 100-ton mining dump truck in this paper.And inspired by the dynamic programming(DP)algorithm,a predictive equivalent consumption minimization strategy(P-ECMS)based on the DP optimization result is proposed.Based on the optimal control manifold and the SOC reference trajectory obtained by the DP algorithm,the P-ECMS strategy performs real-time stage parameter optimization to obtain the optimal equivalent factor(EF).Finally,applying the equivalent consumption minimization strategy(ECMS)realizes real-time control.The simulation results show that the equivalent fuel consumption of the P-ECMS strategy under the experimentally collected mining cycle conditions is 150.8 L/100 km,which is 10.9%less than that of the common CDCS strategy(169.3 L/100 km),and achieves 99.47%of the fuel saving effect of the DP strategy(150 L/100 km).
文摘Intermodal competition changes with changes in technology, economics, and environmental concerns. Trucks and airships are generally considered not to be competitors, but this depends on the distance of haul. The tonne-kilometer cost of trucking rises much more quickly with distance than it does the cost of a cargo airship. At some distance, the two modes are direct substitutes. The costs of the Mexico-Canada refrigerated truck supply chain are compared with the costs of a 100t-lift, electrically-powered airship. The flight characteristics of the Hindenburg Zeppelin are used as a model for a modern cargo airship. The supply chain cost of trucking tomatoes is used to test the theorical proposition. The cost difference works out to about US10¢/kg (5¢/lb) advantage for trucking Mexican tomatoes to Canada. However, this cost disadvantage of the airship could be made up by their vibrationless ride, better air circulation and one-day service versus four days by truck. This alternative form of transportation could have a positive impact on worldwide north-south distribution of food. Airships can overcome trade barriers and distance to open new markets for perishable food exports. In addition, they would reduce the carbon emissions of transport. Canada imports 160,000 refrigerated truckloads of fruits and vegetables by from the southern US and Mexico. With an average driving distance of 3,000 km, these trucks emit 606,000 MT of CO<sub>2</sub> annually. Airships powered by hydrogen fuel cells would have zero-carbon emissions. Markets are not yet incorporating the environmental advantage of airships in any freight comparison, but inevitably this will be important.
文摘Introduction: Over-drowsiness is a condition with serious consequences, including road accidents. The condition, however, is often ignored both by carers as well as victims themselves. The aim of the present study was to investigate the factors associated with excessive drowsiness in Cotonou, Benin 2023, along with its influence on the occurrence of crashes among truck drivers. Methods: This was a descriptive and analytical cross-sectional study, held from March 13 to April 10, 2023, focusing on large truck drivers over 18 years of age, selected by convenience from parking lots in and around the city of Cotonou. Data collected using questionnaires on socio-demographic and behavioral factors, sleeping habits and working conditions were processed using Stata 15.0 software. Excessive drowsiness was defined by a score above 10 on the Epworth scale. Associated factors were found by multiple logistic regression, at a threshold of 0.05. Results: Altogether 304 drivers, all male and aged 35.98 ± 8.42 years, were surveyed. The prevalence of excessive drowsiness was 29.2%. The associated factors identified were not practicing sport OR = 2.27, CI95% = [1.33;3.86], p = 0,002;sleep duration per working day OR = 1.82;CI95% = [1.06;3.11], p = 0,027 and average distance travelled per day OR = 3.40;CI95% = [1.53;7.56], p = 0,003. Excessive drowsiness was associated with a 1.73-fold increased risk of road accidents (CI95% [1.04;2.87];p = 0.03). Conclusion: Communicating excessive drowsiness and its associated factors to all the stakeholders in the haulage chain is essential to help prevent road accidents.
文摘In-cab alerts warn commercial vehicle drivers of upcoming roadway incidents, slowdowns and work zone construction activities. This paper reports on a study evaluating the driver response to in-cab alerts in Ohio. Driver response was evaluated by measuring the statistical trends of vehicle speeds after the in-cab alerts were received. Vehicle speeds pre and post in-cab alert were collected over a 47 day period in the fall of 2023 for trucks traveling on interstate roadways in Ohio. Results show that approximately 22% of drivers receiving Dangerous Slowdown alerts had reduced their speeds by at least 5 mph 30 seconds after receiving such an alert. Segmenting this analysis by speed found that of vehicles traveling at or above 70 mph at the time of alerting, 26% reduced speeds by at least 5 mph. These speed reductions suggest drivers taking actional measures after receiving alerts. Future studies will involve further analysis on the impact of the types of alerts shown, roadway characteristics and overall traffic conditions on truck speeds passing through work zones.
文摘The prevalence of human immunodeficiency virus (AIDS) and hepatitis B virus among heavy truck drivers and their assistants has been well documented globally in correlation with their behavioral characteristics. The present study aimed to screen for human immunodeficiency virus (HIV), hepatitis B virus (HBV), and behavioral characteristics among heavy truck drivers in Port Sudan. A cross-sectional study was conducted on 274 heavy truck drivers and their assistants who used the highway Port Sudan-Khartoum in Port Sudan city during 2019-2021. Data on behavioral characteristics and substance use habits were collected using a structured questionnaire, and an ELISA test was used to screen for HIV and HBV infections in the study participants. The chi-square test, odds ratio, and confidence intervals were used to find the association between behavioral characteristics and seropositive HIV/HBV. Of the 274 enrolled participants, the seroprevalence rates of HIV were 2.7% and HBV was 23.7%. Ninety-four (34.3%) of them had a history of high-risk sexual behavior outside of marriage;only two (0.7%) used condoms;14.2% of participants reported alcohol use;and 1.1% reported drug use. Univariate analysis revealed that having a sex history outside of marriage with ≥1 sex partner and never using a condom with a spouse or casual partner were significant risk factors for HIV and HBV among drivers. Fortunately, we found that most of the drivers reported low alcohol and drug use. Concerning this study, the seroprevalence of HIV and HBV is highly associated with a history of having sex outside of marriage and sexual behavior among truck drivers and assistances. Additional studies are needed to further investigate other STIs and behavioral characteristics associated with factors in truck drivers/assistance in different truck stop regions in Sudan.
文摘Truck frames should be designed and fabricated with enough rigidity to avoid excessive deflections. Finite element analysis (FEA) plays an important role in all stages of frame designs. While being accurate, 3D solid element FEA models are built upon frame configuration details which are not feasible in the preliminary design stage, partially because of limited available design data of frames and heavy computation costs. This research develops 1D beam element FEA models for simulating frame structures. In this paper, the CAD model of a truck frame is first created. The solid element FEA analysis, which is adopted as the baseline in this study, is subsequently conducted for the stiffness of the frame, Next, beam element FEA analysis is performed for validating the feasibility of the beam element FEA model by comparing the results from the solid and beam element FEA models. It is found that the beam element FEA model can predict the frame stiffness with acceptable accuracy and reduce the computation cost significantly.
文摘This study demonstrates a practical cycle time analysis of dump truck haulage system of “Ukhaa Khudag” open-pit coal mine located in Umnugobi Province, Mongolia. It examines the possibility of minimizing the cycle time of the haulage system as well as factors impacting the speed of the dump truck. The current study divides the open pit mine road for the dump trucks into five sections which are bench road, ramp, surface road, dump road uphill, and dump road. Meanwhile, it investigates the influence of the length, the grade, and the rolling resistance of the road section on the cycle time. The data is analyzed using mathematical regression methods via Microsoft Excel program. For each of the five road sections, we compare the statistical calculations of three regression models: linear, quadratic and exponential;thus, a total of thirty regression models are obtained in this research. Accordingly, the cycle time for each road section is predicted by the most accountable model. The loaded and empty direction of the movement is measured and calculated for each road section, and it appears that the difference between the calculated mean value and the actual cycle time of the models is 0.82 seconds with a relative error of 2.51 percent.
基金2022 Liaoning Natural Science Foundation Plan(Yingkou Joint Fund)Damping damping Design and Optimization of New Bore Head Transmission Structure(Fund No.:2022-YKLH-17)In 2023,the key scientific research project of Yingkou Institute of Technology is the Design and Optimization of Smoke Drainage Pipe for New Mining Truck(Fund No.:ZDIL202306)2021 Natural Science Foundation of Liaoning Province(Yingkou Joint Fund)Research on Dynamic Characteristics of Damped Dynamic Reduction Vertical Holack(Fund No.:2021-YKLH-08).
文摘In order to improve the maintenance efficiency,extend the use time,ensure that the exhaust emission meets the standard,forthe 830E truck heating bucket exhaust pipe design defects,the current single smoke exhaust system is transformed into atime period,convertible smoke exhaust system.After the transformation,it can not only realize the side row to prevent direct corrosion of the box bucket in summer,but also realize the heating of the box bucket at low temperature in winter to prevent snow and ice and frozen blocks from sticking to the box bucket and the materials transported.After the transformation can save a lot of manpower,material resources,financial resources,improve the service life.
文摘In 2016 alone, around 4000 people died in crashes involving trucks in the USA, with 21% of these fatalities involving only single-unit trucks. Much research has identified the underlying factors for truck crashes.However, few studies detected the factors unique to single and multiple crashes, and none have examined these underlying factors to severe truck crashes in conjunction with violation data. The current research assessed all of these factors using two approaches to improve truck safety.The first approach used ordinal logistic regression to investigate the contributory factors that increased the odds of severe single-truck and multiple-vehicle crashes, with involvement of at least one truck. The literature has indicated that past violations can be used to predict future violations and crashes. Therefore, the second approach used risky violations, related to truck crashes, to identify the contributory factors to the risky violations and truck crashes. Driver actions of failure to keep proper lane following too close and driving too fast for conditions accounted for about 40% of all the truck crashes. Therefore, the same violations as the aforementioned driver actions were included in the analysis. Based on ordinal logistic regression, the analysis for the first approach indicated that being under non-normal conditions at the time of crash, driving on dry-road condition and having a distraction in the cabin are some of the factors that increase the odds of severe single-truck crashes. On the other hand,speed compliance, alcohol involvement, and posted speed limits are some of the variables that impacted the severity of multiple-vehicle, truck-involved crashes. With the second approach, the violations related to risky driver actions,which were underlying causes of severe truck crashes, were identified and analysis was run to identify the groups at increased risk of truck-involved crashes. The results of violations indicated that being nonresident, driving offpeak hours, and driving on weekends could increase the risk of truck-involved crashes. This paper offers an insight into the capability of using violation data, in addition to crash data, in identification of possible countermeasures to reduce crash frequency.
文摘Roundabouts in United States and other countries have been proved to be very successful, effective, and a safe traffic control treatment. Roundabouts in the context of regularly expected truck configuration have also been successful for effective roundabout designs;however, there are always some site specific issues for trucks accommodation at roundabouts. Therefore, there is a great need for an informational guide in the form of synthesis report for roundabout designs specific to unique trucking traffic activity. While there are not significant literatures and studies in this subject, there are few studies/reports spread out which address various issues in this subject area. This study attempts to synthesize the research and knowledge of truck accommodation at roundabouts by synthesizing various research studies, reports, and articles;various subject areas such as roundabout designs for trucking activity, roundabout designs and accommodation strategies for specialized trucking activity such as oversized trucks, truck safety at roundabouts, and motor carrier perspective of trucking at roundabouts have been analyzed and relevant knowledge has been synthesized. This synthesis can be useful o researchers, designers, planners, and decision makers to determine effective ways to address specific trucking related issues at a roundabout.
基金National Natural Science Foundation of China(Grant No.51505178)China Postdoctoral Science Foundation(Grant No.2014M561289)
文摘Di erential braking and active steering have already been integrated to overcome their shortcomings. However, existing research mainly focuses on two-axle vehicles and controllers are mostly designed to use one control method to improve the other. Moreover, many experiments are needed to improve the robustness; therefore, these control methods are underutilized. This paper proposes an integrated control system specially designed for multi-axle vehicles, in which the desired lateral force and yaw moment of vehicles are determined by the sliding mode control algorithm. The output of the sliding mode control is distributed to the suitable wheels based on the abilities and potentials of the two control methods. Moreover, in this method, fewer experiments are needed, and the robustness and simultaneity are both guaranteed. To simplify the optimization system and to improve the computation speed, seven simple optimization subsystems are designed for the determination of control outputs on each wheel. The simulation results show that the proposed controller obviously enhances the stability of multi-axle trucks. The system improves 68% of the safe velocity, and its performance is much better than both di erential braking and active steering. This research proposes an integrated control system that can simultaneously invoke di erential braking and active steering of multi-axle vehicles to fully utilize the abilities and potentials of the two control methods.
基金Sponsored by the National High Technology Research and Development Program:Underground Mining Intelligent Truck(Grant No.2011AA060404)
文摘The requirements of vehicle dynamic stability control are higher than ever as the significant increase of electric drive articulated vehicle speed. According to the construction features of articulated dumping truck and nonlinear characteristics of moving vehicles,nonlinear observer of vehicle status is designed to strength robustness of dynamic control system in this paper. A 4-degree-of-freedom nonlinear dynamic model of articulated electric drive vehicle is built as reference model to estimate the state of the articulated vehicle. And by adopting Unscented Kalman Filter( UKF) algorithm,a series of state parameters such as longitudinal velocities of front and rear frames,yaw rate and side-slip angle are estimated. During the test of 60 t articulated electric drive vehicle,2 inertial navigation modules are installed in the front frame and rear frame respectively and the speed of each electric drive wheel is obtained simultaneously. As the test results suggest,in various working conditions,the algorithm based on UKF is able to accurately estimate the state parameters of articulated vehicle with the estimated error less than 5%. The proposed method is justified to be the theoretical basis and application guidance for articulated vehicle stability control.
文摘In a global environment where energy and labor are becoming increasingly expensive, continuous mining systems such as In-Pit Crushing and Conveying(IPCC) systems have been advanced as offering a real alternative to conventional truck haulage systems. The implementation of IPCC systems in hard rock operations in open pit mines however requires different and more comprehensive planning approaches in order to adequately reflect the practical aspects associated with these. This paper investigates the impact that these approaches may have on the implementation of IPCC systems on a basic metalliferous deposit amenable to open pit exploitation. A strategic life of mine plan to provide numerous economic indicators for each approach is analyzed and compared to traditional truck haulage systems. The mine planning and evaluation process highlights the increased overall resource recovery that may accompany the use of IPCC systems. This investigation also provides insights into the issues associated with IPCC and the scale and type of operation and orebody that is likely to provide a feasible alternative to truck haulage.
基金Supported by National Natural Science Foundation of China(Grant Nos.51775269,U1964203,52072215)National Key R&D Program of China(Grant No.2020YFB1600303).
文摘It is very necessary for an intelligent heavy truck to have the ability to prevent rollover independently.However,it was rarely considered in intelligent vehicle motion planning.To improve rollover stability,a motion planning strategy with autonomous anti rollover ability for an intelligent heavy truck is put forward in this paper.Considering the influence of unsprung mass in the front axle and the rear axle and the body roll stiffness on vehicle rollover stability,a rollover dynamics model is built for the intelligent heavy truck.From the model,a novel rollover index is derived to evaluate vehicle rollover risk accurately,and a model predictive control algorithm is applicated to design the motion planning strategy for the intelligent heavy truck,which integrates the vehicle rollover stability,the artificial potential field for the obstacle avoidance,the path tracking and vehicle dynamics constrains.Then,the optimal path is obtained to meet the requirements that the intelligent heavy truck can avoid obstacles and drive stably without rollover.In addition,three typical scenarios are designed to numerically simulate the dynamic performance of the intelligent heavy truck.The results show that the proposed motion planning strategy can avoid collisions and improve vehicle rollover stability effectively even under the worst driving scenarios.