The interaction of U-shaped rings used for power transmission hardware with a wind-sand field is simulated numerically.A standard kturbulence model is used in synergy with an Eulerian-Lagrangian approach.The results...The interaction of U-shaped rings used for power transmission hardware with a wind-sand field is simulated numerically.A standard kturbulence model is used in synergy with an Eulerian-Lagrangian approach.The results show that the wind pressure on the windward side of the U-shaped ring is the highest,a negative pressure zone appears on both sides of the U-shaped ring,while a Kármán Vortex Street is created on its leeward side.There are three possible regimes of motion for the sand grains in the wind field.Sand grains with size below 0.125 mm can follow the airflow directly into the contact area of two U-shaped rings.When the sand size is about 0.1 mm,the number of sand grains that are blown into the contact area attains a maximum.Through the simulation of U-shaped rings in the wind-sand field,the dynamics of such processes are explained in detail,thereby providing relevant information for the subsequent protection and design of connecting hardware used for power transmission.展开更多
The formulae for stresses and angular displacements of U-shaped bellows overall bending in a meridian plane under pure bending moments are presented based on the general solution for slender ring shells proposed by Zh...The formulae for stresses and angular displacements of U-shaped bellows overall bending in a meridian plane under pure bending moments are presented based on the general solution for slender ring shells proposed by Zhu Weiping, et al. and the solution for ring plates. The results evaluated in this paper are compared with those on EJMA (standards of the expansion joint manufacturers association) and of the experiment given by Li Tingxilz, et al.展开更多
Ring footings are suitable for the structures like tall transmission towers, chimneys, silos and oil storages.These types of structures are susceptible to horizontal loads(wind load) in addition to their dead weight.I...Ring footings are suitable for the structures like tall transmission towers, chimneys, silos and oil storages.These types of structures are susceptible to horizontal loads(wind load) in addition to their dead weight.In the literature, very little or no effort has been made to study the effect of ring footing resting on reinforced sand when subjected to eccentric, inclined and/or eccentric-inclined loadings. This paper aims to study the behavior of ring footing resting on loose sand and/or compacted randomly distributed fiberreinforced sand(RDFS) when subjected to eccentric(0 B, 0.05 B and 0.1 B, where B is the outer diameter of ring footing), inclined(0°,5°,10°, 15°,-5°,-10° and-15°)and eccentric-inclined loadings by using a finite element(FE) software PLAXIS 3 D. The behavior of ring footing is studied by using a dimensionless factor called reduction factor(RF). The numerical model used in the PLAXIS 3 D has been validated by conducting model plate load tests. Moreover, an empirical expression using regression analysis has been presented which will be helpful in plotting a load-settlement curve for the ring footing.展开更多
We experimentally tested under radial compressive loads and statistically analyzed rings constructed from spruce wood and reinforced with glass fiber.We used the Weibull distribution in statistical analysis,and tested...We experimentally tested under radial compressive loads and statistically analyzed rings constructed from spruce wood and reinforced with glass fiber.We used the Weibull distribution in statistical analysis,and tested five types of rings including unreinforced and composite reinforced（CR） as wound around the ring,oriented as two layers at angles of 45°,60°,75° and 90° to the column axis.We calculated 95 % reliability of load carrying capacity of the rings by Weibull distribution.The highest load carrying capacity was obtained with CR rings at 60° to the axial axis of the ring.Load carrying capacities of rings at CR90,CR75,CR60 and CR45 were 137,192,215 and 126 %greater,respectively,than unreinforced rings.For unreinforced rings,failures resulted from catastrophic breaking of wood materials.None of the reinforced rings failed catastrophically because the outer surface of the rings was reinforced with glass–epoxy composite fiber.Cracks began at the core of the materials under the composite layer for all specimens and resulted in failure of the rings.展开更多
基金National Natural Science Foundation of China(51865055)Tianshan Talents Plan of Xinjiang Autonomous Region of China(201720025)。
文摘The interaction of U-shaped rings used for power transmission hardware with a wind-sand field is simulated numerically.A standard kturbulence model is used in synergy with an Eulerian-Lagrangian approach.The results show that the wind pressure on the windward side of the U-shaped ring is the highest,a negative pressure zone appears on both sides of the U-shaped ring,while a Kármán Vortex Street is created on its leeward side.There are three possible regimes of motion for the sand grains in the wind field.Sand grains with size below 0.125 mm can follow the airflow directly into the contact area of two U-shaped rings.When the sand size is about 0.1 mm,the number of sand grains that are blown into the contact area attains a maximum.Through the simulation of U-shaped rings in the wind-sand field,the dynamics of such processes are explained in detail,thereby providing relevant information for the subsequent protection and design of connecting hardware used for power transmission.
文摘The formulae for stresses and angular displacements of U-shaped bellows overall bending in a meridian plane under pure bending moments are presented based on the general solution for slender ring shells proposed by Zhu Weiping, et al. and the solution for ring plates. The results evaluated in this paper are compared with those on EJMA (standards of the expansion joint manufacturers association) and of the experiment given by Li Tingxilz, et al.
文摘Ring footings are suitable for the structures like tall transmission towers, chimneys, silos and oil storages.These types of structures are susceptible to horizontal loads(wind load) in addition to their dead weight.In the literature, very little or no effort has been made to study the effect of ring footing resting on reinforced sand when subjected to eccentric, inclined and/or eccentric-inclined loadings. This paper aims to study the behavior of ring footing resting on loose sand and/or compacted randomly distributed fiberreinforced sand(RDFS) when subjected to eccentric(0 B, 0.05 B and 0.1 B, where B is the outer diameter of ring footing), inclined(0°,5°,10°, 15°,-5°,-10° and-15°)and eccentric-inclined loadings by using a finite element(FE) software PLAXIS 3 D. The behavior of ring footing is studied by using a dimensionless factor called reduction factor(RF). The numerical model used in the PLAXIS 3 D has been validated by conducting model plate load tests. Moreover, an empirical expression using regression analysis has been presented which will be helpful in plotting a load-settlement curve for the ring footing.
文摘We experimentally tested under radial compressive loads and statistically analyzed rings constructed from spruce wood and reinforced with glass fiber.We used the Weibull distribution in statistical analysis,and tested five types of rings including unreinforced and composite reinforced（CR） as wound around the ring,oriented as two layers at angles of 45°,60°,75° and 90° to the column axis.We calculated 95 % reliability of load carrying capacity of the rings by Weibull distribution.The highest load carrying capacity was obtained with CR rings at 60° to the axial axis of the ring.Load carrying capacities of rings at CR90,CR75,CR60 and CR45 were 137,192,215 and 126 %greater,respectively,than unreinforced rings.For unreinforced rings,failures resulted from catastrophic breaking of wood materials.None of the reinforced rings failed catastrophically because the outer surface of the rings was reinforced with glass–epoxy composite fiber.Cracks began at the core of the materials under the composite layer for all specimens and resulted in failure of the rings.
