UV-curable polyurethane prepolymer and photoinitiator 1173 were facilely encapsulated in a poly（urea-formaldehyde） shell, which was in situ formed by the polymerization of formalde-hyde and urea in an oil-in-water e...UV-curable polyurethane prepolymer and photoinitiator 1173 were facilely encapsulated in a poly（urea-formaldehyde） shell, which was in situ formed by the polymerization of formalde-hyde and urea in an oil-in-water emulsion. The diameters of the microcapsules ranged from 118 μm to 663 μm depending on agitation speed, and were obtained via optical mi-croscopy and scanning electron microscopy analyses. The encapsulation percent and the yield of microcapsules prepared at the agitation speed of 600 r/min can reach 97.52wt% and 65.23wt%, respectively. When the water-borne polyurethane （WPU） coating embedded with the prepared microcapsules were scratched, the healing agent could be released from rup-tured microcapsules and lled the scribed region. The excellent anticorrosion properties of the WPU coating embedded with the prepared microcapsules were con rmed by the results obtained from both electrochemical impedance spectroscopy and Tafel curves.展开更多
UV-curable hyperbranched polyurethane （UV-HBPU） containing carboxyl groups was synthesized from isophorone diisocyanate （IPDI）, diethanolamine （DEOA）, polyethylene glycol （PEG-400）, hydroxyethyl acrylate （HEA...UV-curable hyperbranched polyurethane （UV-HBPU） containing carboxyl groups was synthesized from isophorone diisocyanate （IPDI）, diethanolamine （DEOA）, polyethylene glycol （PEG-400）, hydroxyethyl acrylate （HEA）, and 2,2-his （hydroxymethyl） propionic acid （DMPA）. The UV-HBPU was used as a negative-type photoresist for a printed circuit board （PCB）. Fourier-transform infrared spectroscopy （FTIR） and proton nuclear magnetic resonance （1HNMR） spectroscopy of UV-HBPUs indicated that the synthesis was successful. Differential scanning calorimetry （DSC） and thermogravimetric analysis （TGA） showed that the thermal stability of the UV-HBPUs decreased as the HEA content increased. The polymer exhibited excellent photoresist properties, and the resolution of circuits based on this negative-type photoresist reached 10 μm.展开更多
Finer nanoplates of silver are prepared by self-assembly on the surface of graphene,and the low-temperature sintered high conductivity ink containing the silver nanoplates is prepared.Most importantly,graphene is adde...Finer nanoplates of silver are prepared by self-assembly on the surface of graphene,and the low-temperature sintered high conductivity ink containing the silver nanoplates is prepared.Most importantly,graphene is added to the solution before the chemical reduction reaction occurs.Firstly,it is found that silver nanoplates have self-assembly phenomenon on the surface of graphene.Secondly,the Ag nano hexagonal platelets(AgNHPs)with small particle sizes(10 nm),narrow distribution and good dispersion are prepared.Especially,smaller sizes(10 nm)and narrower particle size distribution of AgNHPs particles can be easily controlled by using this process.Finally,the conductivity of the ink is excellent.For example,when the printed patterns were sintering at 150℃,the resistivity of the ink(GE:0.15 g/L)reached the minimum value of 2.2×10^-6 cm.And the resistivity value was 3.7×10^-6Ωcm,when it was sintered at 100℃ for 30 min.The conductive ink prepared can be used for the field of printing electronics as ink-jet printing ink.展开更多
A novel UV-curable prepolymer polypropyleneglycol diglycidyl ether diacrylate （PPGGEA） was synthesized by utilizing polypropyleneglycol diglycidyl ether （PPGGE） and acrylic acid （AA） as starting materials, N, N-...A novel UV-curable prepolymer polypropyleneglycol diglycidyl ether diacrylate （PPGGEA） was synthesized by utilizing polypropyleneglycol diglycidyl ether （PPGGE） and acrylic acid （AA） as starting materials, N, N-dimethylbenzylamine as catalyst and p-hydroxyanisole as inhibitor. The optimum synthetic conditions were in the following： the concentration of N, N-dimethylbenzylamine was 0.80 wt% of reactants, the concentration of p-hydroxyanisole was 0.3 wt% of reactants, the reaction temperature was 90-110 ~C, and the molar ratio of PPGGE to AA was 1：2.2. Meanwhile, 1-hydroxycyclohexyl phenyl ketone of a UV-cured initiator was added to the synthesized PPGGEA to prepare a kind of UV-cured coating. The mechanical properties of the UV-cured films were determined, giving 29.99 MPa of tensile strength, 834.27 MPa of the Young＇s modulus and 5.66% of elongation at tear.展开更多
A novel UV-curable prepolymer hexanediol diglycidyl ether diacrylate （HDGEA） was synthesized by utilizing hexanediol diglycidyl ether （HDGE） and acrylic acid （AA） as starting materials, N, N-dimethylbenzylamine ...A novel UV-curable prepolymer hexanediol diglycidyl ether diacrylate （HDGEA） was synthesized by utilizing hexanediol diglycidyl ether （HDGE） and acrylic acid （AA） as starting materials, N, N-dimethylbenzylamine as catalyst and p-hydroxyanisole as inhibitor. The optimal synthetic conditions were that the concentration of N, N-dimethylbenzylamine was 0.80 wt% of reactants, the concentration of p-hydroxyanisole was 0.3 wt% of reactants, the reaction temperature was 90-110 ℃, and the molar ratio of HDGE to AA was 1︰2.2. Meanwhile, 1-hydroxycyclohexyl phenyl ketone of a UV-curing initiator was added to the synthesized HDGEA to prepare a kind of UV-curing coating. The mechanical properties of the UV-cured films were determined, giving 31.87 MPa of tensile strength, 871.88 MPa of Young＇s modulus and 6.77% of elongation at tear.展开更多
Ink-jet printing of ceramic thick films is one of low cost on-site ceramic pattern fabrication methods.It is necessary to investigate the rheological behaviour of ceramic inks and drying behaviour of droplets.Two kind...Ink-jet printing of ceramic thick films is one of low cost on-site ceramic pattern fabrication methods.It is necessary to investigate the rheological behaviour of ceramic inks and drying behaviour of droplets.Two kinds of BaTiO3 ceramic inks were prepared by mechanical mixing and sol-gel methods,respectively.The effect of preparation parameters,such as quantity of polyacrylic acid(PAA)and solid content,on physicochemical and rheologic properties of the ceramic inks was investigated.The results show that they satisfy the requirements of continuous ink-jet printing.The appearances of printed dots and single printed layers were observed by SEM.The SEM images indicate that dots printed with mixing method ink are in ring shape,and dots printed with sol-gel method ink are in pancake shape,so the printed layer surface with the latter ink is smoother.The causes of these phenomena were discussed.展开更多
A novel photosensitive copolymer P（SS-co-AA-g-GMA）（PSAG） was synthesized and utilized to noncovalently functionalize pristine single-walled carbon nanotubes（SCNTs）. PSAG was highly effective for the solubilizati...A novel photosensitive copolymer P（SS-co-AA-g-GMA）（PSAG） was synthesized and utilized to noncovalently functionalize pristine single-walled carbon nanotubes（SCNTs）. PSAG was highly effective for the solubilization of SCNTs in water and validated by UV-vis absorption spectra experiments, resulting in homogeneous and stable PSAG-SCNT aqueous dispersion. The microstructure of SCNTs was observed through Raman spectroscopy and transmission electron microscopy. In addition, compared with the two common polymeric dispersants of Triton X-100 and PSS, PSAG demonstrated more effective performances for dispersing SCNTs under identical conditions. Furthermore, the photosensitive PSAG-SCNTs can be crosslinked after UV irradiation, leading to significant improvement in the water resistance of SCNT films. UV-cured films can be transferred to plastic wrap to form a flexible film with high electrical conductivity.展开更多
A series of photosensitive random copolymers （UPDHES） were prepared by introducing acrylate groups onto the side chain of the copolymer backbone of N, N-domethyl amimethyl methacrylate （DMAEMA）, 2-hydroxypropyl ac...A series of photosensitive random copolymers （UPDHES） were prepared by introducing acrylate groups onto the side chain of the copolymer backbone of N, N-domethyl amimethyl methacrylate （DMAEMA）, 2-hydroxypropyl acrylate （HEA）, 2-ethylhexyl acrylate （EHA）, and styrene （St） （PDHES）. The molecular structure of UPDHES was characterized by FTIR, 1HNMR and GPC. The photopolymerization kinetics of UPDHES with different C=C content was investigated using real time FTIR in which it was found that the UPDHES system had notable photosensitivity. The effect of C=C content on the properties of cured films were studied by evaluating various film properties such as thermal stability, glass transition temperature and tensile properties. The thermal degradation of cured films was investigated via thermogravimetric analysis/infrared spectrometry （TGA-IR）. Thus a series of UV-curable electrodeposition coatings with good photosensitivity and mechanical properties were prepared from a low-cost photosensitive random copolymer.展开更多
In this work, we study the stability of a class of materials obtained by printing a textile with conductive inks using a method called screen printing. Under the action of a certain external factors, the printed circu...In this work, we study the stability of a class of materials obtained by printing a textile with conductive inks using a method called screen printing. Under the action of a certain external factors, the printed circuit suffers deterioration and the conductivity decreases considerably. In this work, we propose to model the overall damage of the textile sheet in terms of the partial damages of the conductive lines. We also apply this approach to evaluate the damage of a system being made of transmission lines printed into nonwoven substrates using different conductive inks.展开更多
While the practice of tattooing has existed for thousands of years, it has recently begun growing in popularity in the US. With the increasing prevalence of tattoos, the methods and inks involved in the tattooing proc...While the practice of tattooing has existed for thousands of years, it has recently begun growing in popularity in the US. With the increasing prevalence of tattoos, the methods and inks involved in the tattooing process have also developed. Tattoos now use many brightly colored inks, often made using metal-based pigments. There is concern that chemicals may be present in tattoo inks in concentrations that may lead to human health concerns either during application or removal of tattoos. Since exposure to metals has been linked to tremors, liver damage, memory loss, cognitive loss, and even death, there is concern about the prevalence of metals in tattoo inks in general. To this end, a survey of 226 commercial tattoo inks was performed and each ink was analyzed for the presence of heavy metals using two different x-ray methods: Particle Induced X-Ray Emission and Scanning Electron Microscopy/ Energy Dispersive Spectroscopy. Fifteen metals were identified in various tattoo inks by these rapid x-ray methods, including chromium, manganese, nickel, copper, barium, and lead. Conclusions can be drawn about the prevalence of metals in some pigment colors and from some brands.展开更多
A novel UV-curable diluent benzyl glycidyl ether acrylate(BGEA) was synthesized by utilizing benzyl glycidyl ether(BGE) and acrylic acid(AA) as starting materials,N,N-dimethylbenzylamine as catalyst and p-hydroxyaniso...A novel UV-curable diluent benzyl glycidyl ether acrylate(BGEA) was synthesized by utilizing benzyl glycidyl ether(BGE) and acrylic acid(AA) as starting materials,N,N-dimethylbenzylamine as catalyst and p-hydroxyanisole as inhibitor.The optimum synthetic conditions were that the concentration of N,N-dimethylbenzylamine was 0.90% of reactants by weight,the concentration of p-hydroxyanisole was 0.20% of reactants by weight,the reaction temperature was 90-100℃,and the molar ratio of BGE to AA was 1.00:1.10.The experiment shows that BGEA is a kind of good diluent.The mechanical properties of the UV-cured films with BGEA as diluent to prepare UV-curing coating were superior to that of the UV-cured films with butyl acrylate as diluent to prepare UV-curing coating.展开更多
To reduce the impact of the novel SARS-CoV-2 virus, popularly known as the Coronavirus, many public health-related rules have been established around the world. Along with social distancing and lockdowns, most countri...To reduce the impact of the novel SARS-CoV-2 virus, popularly known as the Coronavirus, many public health-related rules have been established around the world. Along with social distancing and lockdowns, most countries have mandatory wearing of face masks in public areas to limit the spread of the virus during the COVID-19 pandemic. However, because people are free to choose any method to make their masks, some are being fabricated from materials that can be toxic to the environment and human health. This paper discusses how inks and dyes used in face masks are causing major environmental degradation and health issues in industry workers and the general mask-wearing public. The goal fixed for the present study is to raise the alarm with authorities and decision-makers regarding the toxic nature of some colors (dyes and inks) and fabrics in the masks being worn every day.展开更多
Precursor (Metal-organic decomposition (MOD)) inks are used to fabricate 2D and 3D printed conductive structures directly onto a substrate. By formulating a nanoalloy structure containing multiple metals, the opportun...Precursor (Metal-organic decomposition (MOD)) inks are used to fabricate 2D and 3D printed conductive structures directly onto a substrate. By formulating a nanoalloy structure containing multiple metals, the opportunity to modify chemical and physical properties exists. In this paper, a copper-nickel bimetallic nanoalloy film was fabricated by mixing copper and nickel precursor inks and sintering them in vacuum. The individual elemental inks were formulated and characterized using SEM, EDS, and XRD. During thermal processing, elemental copper forms first and is followed by the formation of bimetallic copper-nickel alloy. The encapsulation of the underlying copper by the nickel-rich alloy provides excellent oxidation resistance. No change in film resistance was observed after the film was exposed to an oxygen plasma. Nanoalloy films printed using reactive metallic inks have a variety of important applications involving local control of alloy composition. Examples include facile formation of layered nanostructures, and electrical conductivity with oxidative stability.展开更多
A novel UV-curable oligmer 1,4-cyclohexanedimethanol glycidyl ether acrylate（CHDMGEA） was synthesized by utilizing 1,4-cyclohexanedimethanol glycidyl ether（CHDMGE） and acrylic acid（AA） as starting materials, tri...A novel UV-curable oligmer 1,4-cyclohexanedimethanol glycidyl ether acrylate（CHDMGEA） was synthesized by utilizing 1,4-cyclohexanedimethanol glycidyl ether（CHDMGE） and acrylic acid（AA） as starting materials, triphenyl phosphine as catalyst and p-hydroxyanisole as inhibitor. The optimum synthetic conditions were that the concentration of triphenyl phosphine was 0.90% of reactants by weight, the concentration of p-hydroxyanisole was 0.20% of reactants by weight, the reaction temperature was 90-100 ℃, and the molar ratio of CHDMGE to AA was 0.5：1.1. The experimental results show that CHDMGEA is a kind of good UV-curable oligmer. The impact resistance of the UV-cured films with CHDMGEA as oligmer to prepare UV-curing coating was superior to that of the UV-cured films with bisphenol A diglycidyl ether diacrylate（BPGEA） as oligmer to prepare UV-curing coating.展开更多
A novel UV-curable prepolymer neopentyl glycol diglycidyl ether diacrylate (NPGGEA) was synthesized by using neopentyl glycol diglycidyl ether (NPGGE) and acrylic acid (AA) as starting materials, N, N-dimethylbenzylam...A novel UV-curable prepolymer neopentyl glycol diglycidyl ether diacrylate (NPGGEA) was synthesized by using neopentyl glycol diglycidyl ether (NPGGE) and acrylic acid (AA) as starting materials, N, N-dimethylbenzylamine as catalyst and p-hydroxyanisole as inhibitor. The optimum synthetic conditions were taken as follows: The concentration of N,N-dimethylbenzylamine, 0.80% of reactants; the concentration of p-hydroxyanisole, 0.3% of reactants; the reaction temperature, 90-110 ; the molar ratio of NPGGE to AA, 1:2.2. Meanwhile, 1-hydroxycyclohexyl phenyl ketone of a UV-cured initiator was added to the synthesized NPGGEA to prepare a kind of UV-cured coating. Mechanical properties of the UV-cured films were determined, giving 28.75 MPa of tensile strength, 923.82 MPa of Young’s modulus and 5.51% of elongation at tear.展开更多
This work describes the application of a detailed set of TXRF evaluations to the elemental content of assorted tattoo inks, on the market of the city of Concepcion, Chile. We applied TXRF as a screening method for det...This work describes the application of a detailed set of TXRF evaluations to the elemental content of assorted tattoo inks, on the market of the city of Concepcion, Chile. We applied TXRF as a screening method for determining the composition in 3 sets of tattoo inks, in order to establish, from an inorganic point of view, the composition and purity of the samples, evaluating their elemental innocuousness. The analyzed 48 products were freely acquired from on line suppliers. All of them were analyzed by external standard quantification, but in order to inter-compare the results, a 15% of the samples were acidly digested and then quantified by the internal standard method. In the samples we determined: 1) their inorganic quantitative composition and, 2) the possible presence of elements which are potential health hazards. In this study few anomalies were found: 1) The high presence Ti of and W in few samples, 2) Arsenic was found in four of them, and 3) A trace detection of a rare earth element in a particular product. The products studied are almost freely imported from a world open marked, so the questions about their innocuousness could affect not only to the Chilean society.展开更多
文摘UV-curable polyurethane prepolymer and photoinitiator 1173 were facilely encapsulated in a poly（urea-formaldehyde） shell, which was in situ formed by the polymerization of formalde-hyde and urea in an oil-in-water emulsion. The diameters of the microcapsules ranged from 118 μm to 663 μm depending on agitation speed, and were obtained via optical mi-croscopy and scanning electron microscopy analyses. The encapsulation percent and the yield of microcapsules prepared at the agitation speed of 600 r/min can reach 97.52wt% and 65.23wt%, respectively. When the water-borne polyurethane （WPU） coating embedded with the prepared microcapsules were scratched, the healing agent could be released from rup-tured microcapsules and lled the scribed region. The excellent anticorrosion properties of the WPU coating embedded with the prepared microcapsules were con rmed by the results obtained from both electrochemical impedance spectroscopy and Tafel curves.
基金Funded by the National Natural Science Foundation of China(Nos.51203063,51103064)
文摘UV-curable hyperbranched polyurethane （UV-HBPU） containing carboxyl groups was synthesized from isophorone diisocyanate （IPDI）, diethanolamine （DEOA）, polyethylene glycol （PEG-400）, hydroxyethyl acrylate （HEA）, and 2,2-his （hydroxymethyl） propionic acid （DMPA）. The UV-HBPU was used as a negative-type photoresist for a printed circuit board （PCB）. Fourier-transform infrared spectroscopy （FTIR） and proton nuclear magnetic resonance （1HNMR） spectroscopy of UV-HBPUs indicated that the synthesis was successful. Differential scanning calorimetry （DSC） and thermogravimetric analysis （TGA） showed that the thermal stability of the UV-HBPUs decreased as the HEA content increased. The polymer exhibited excellent photoresist properties, and the resolution of circuits based on this negative-type photoresist reached 10 μm.
基金Project(2018GK4015)supported by the Hunan Provincial Strategic Emerging Industry Project,China
文摘Finer nanoplates of silver are prepared by self-assembly on the surface of graphene,and the low-temperature sintered high conductivity ink containing the silver nanoplates is prepared.Most importantly,graphene is added to the solution before the chemical reduction reaction occurs.Firstly,it is found that silver nanoplates have self-assembly phenomenon on the surface of graphene.Secondly,the Ag nano hexagonal platelets(AgNHPs)with small particle sizes(10 nm),narrow distribution and good dispersion are prepared.Especially,smaller sizes(10 nm)and narrower particle size distribution of AgNHPs particles can be easily controlled by using this process.Finally,the conductivity of the ink is excellent.For example,when the printed patterns were sintering at 150℃,the resistivity of the ink(GE:0.15 g/L)reached the minimum value of 2.2×10^-6 cm.And the resistivity value was 3.7×10^-6Ωcm,when it was sintered at 100℃ for 30 min.The conductive ink prepared can be used for the field of printing electronics as ink-jet printing ink.
基金the Innovatory Group Program of the Natural Science Foundation of Hubei Province(No.2004ABC001)the National"863"Hi-tech Foundation of China(No.2002AA6Z3083)
文摘A novel UV-curable prepolymer polypropyleneglycol diglycidyl ether diacrylate （PPGGEA） was synthesized by utilizing polypropyleneglycol diglycidyl ether （PPGGE） and acrylic acid （AA） as starting materials, N, N-dimethylbenzylamine as catalyst and p-hydroxyanisole as inhibitor. The optimum synthetic conditions were in the following： the concentration of N, N-dimethylbenzylamine was 0.80 wt% of reactants, the concentration of p-hydroxyanisole was 0.3 wt% of reactants, the reaction temperature was 90-110 ~C, and the molar ratio of PPGGE to AA was 1：2.2. Meanwhile, 1-hydroxycyclohexyl phenyl ketone of a UV-cured initiator was added to the synthesized PPGGEA to prepare a kind of UV-cured coating. The mechanical properties of the UV-cured films were determined, giving 29.99 MPa of tensile strength, 834.27 MPa of the Young＇s modulus and 5.66% of elongation at tear.
基金Funded by the Natural Science Foundation of Jiangxi Province (No.2008GZC0021)the National "863" Hi-tech Foundation of China (No.2002AA6Z3083)
文摘A novel UV-curable prepolymer hexanediol diglycidyl ether diacrylate （HDGEA） was synthesized by utilizing hexanediol diglycidyl ether （HDGE） and acrylic acid （AA） as starting materials, N, N-dimethylbenzylamine as catalyst and p-hydroxyanisole as inhibitor. The optimal synthetic conditions were that the concentration of N, N-dimethylbenzylamine was 0.80 wt% of reactants, the concentration of p-hydroxyanisole was 0.3 wt% of reactants, the reaction temperature was 90-110 ℃, and the molar ratio of HDGE to AA was 1︰2.2. Meanwhile, 1-hydroxycyclohexyl phenyl ketone of a UV-curing initiator was added to the synthesized HDGEA to prepare a kind of UV-curing coating. The mechanical properties of the UV-cured films were determined, giving 31.87 MPa of tensile strength, 871.88 MPa of Young＇s modulus and 6.77% of elongation at tear.
基金Project(106151)supported by the Major Program of the Ministry of Education of ChinaProject(59842001)supported by the National Natural Science Foundation of China
文摘Ink-jet printing of ceramic thick films is one of low cost on-site ceramic pattern fabrication methods.It is necessary to investigate the rheological behaviour of ceramic inks and drying behaviour of droplets.Two kinds of BaTiO3 ceramic inks were prepared by mechanical mixing and sol-gel methods,respectively.The effect of preparation parameters,such as quantity of polyacrylic acid(PAA)and solid content,on physicochemical and rheologic properties of the ceramic inks was investigated.The results show that they satisfy the requirements of continuous ink-jet printing.The appearances of printed dots and single printed layers were observed by SEM.The SEM images indicate that dots printed with mixing method ink are in ring shape,and dots printed with sol-gel method ink are in pancake shape,so the printed layer surface with the latter ink is smoother.The causes of these phenomena were discussed.
基金Funded by the National Natural Science Foundation of China(No.51403082)
文摘A novel photosensitive copolymer P（SS-co-AA-g-GMA）（PSAG） was synthesized and utilized to noncovalently functionalize pristine single-walled carbon nanotubes（SCNTs）. PSAG was highly effective for the solubilization of SCNTs in water and validated by UV-vis absorption spectra experiments, resulting in homogeneous and stable PSAG-SCNT aqueous dispersion. The microstructure of SCNTs was observed through Raman spectroscopy and transmission electron microscopy. In addition, compared with the two common polymeric dispersants of Triton X-100 and PSS, PSAG demonstrated more effective performances for dispersing SCNTs under identical conditions. Furthermore, the photosensitive PSAG-SCNTs can be crosslinked after UV irradiation, leading to significant improvement in the water resistance of SCNT films. UV-cured films can be transferred to plastic wrap to form a flexible film with high electrical conductivity.
基金Funded by the National Natural Science Foundation of China (50673038 and 20704017)the Innovation Foundation of Jiangsu(BY2011118)
文摘A series of photosensitive random copolymers （UPDHES） were prepared by introducing acrylate groups onto the side chain of the copolymer backbone of N, N-domethyl amimethyl methacrylate （DMAEMA）, 2-hydroxypropyl acrylate （HEA）, 2-ethylhexyl acrylate （EHA）, and styrene （St） （PDHES）. The molecular structure of UPDHES was characterized by FTIR, 1HNMR and GPC. The photopolymerization kinetics of UPDHES with different C=C content was investigated using real time FTIR in which it was found that the UPDHES system had notable photosensitivity. The effect of C=C content on the properties of cured films were studied by evaluating various film properties such as thermal stability, glass transition temperature and tensile properties. The thermal degradation of cured films was investigated via thermogravimetric analysis/infrared spectrometry （TGA-IR）. Thus a series of UV-curable electrodeposition coatings with good photosensitivity and mechanical properties were prepared from a low-cost photosensitive random copolymer.
文摘In this work, we study the stability of a class of materials obtained by printing a textile with conductive inks using a method called screen printing. Under the action of a certain external factors, the printed circuit suffers deterioration and the conductivity decreases considerably. In this work, we propose to model the overall damage of the textile sheet in terms of the partial damages of the conductive lines. We also apply this approach to evaluate the damage of a system being made of transmission lines printed into nonwoven substrates using different conductive inks.
文摘While the practice of tattooing has existed for thousands of years, it has recently begun growing in popularity in the US. With the increasing prevalence of tattoos, the methods and inks involved in the tattooing process have also developed. Tattoos now use many brightly colored inks, often made using metal-based pigments. There is concern that chemicals may be present in tattoo inks in concentrations that may lead to human health concerns either during application or removal of tattoos. Since exposure to metals has been linked to tremors, liver damage, memory loss, cognitive loss, and even death, there is concern about the prevalence of metals in tattoo inks in general. To this end, a survey of 226 commercial tattoo inks was performed and each ink was analyzed for the presence of heavy metals using two different x-ray methods: Particle Induced X-Ray Emission and Scanning Electron Microscopy/ Energy Dispersive Spectroscopy. Fifteen metals were identified in various tattoo inks by these rapid x-ray methods, including chromium, manganese, nickel, copper, barium, and lead. Conclusions can be drawn about the prevalence of metals in some pigment colors and from some brands.
基金Natural Science Foundation of Jiangxi Province of China (No. 2008GZC0021)National High-Tech R&D Program of China(863 program) (No. 2002AA6Z3083)
文摘A novel UV-curable diluent benzyl glycidyl ether acrylate(BGEA) was synthesized by utilizing benzyl glycidyl ether(BGE) and acrylic acid(AA) as starting materials,N,N-dimethylbenzylamine as catalyst and p-hydroxyanisole as inhibitor.The optimum synthetic conditions were that the concentration of N,N-dimethylbenzylamine was 0.90% of reactants by weight,the concentration of p-hydroxyanisole was 0.20% of reactants by weight,the reaction temperature was 90-100℃,and the molar ratio of BGE to AA was 1.00:1.10.The experiment shows that BGEA is a kind of good diluent.The mechanical properties of the UV-cured films with BGEA as diluent to prepare UV-curing coating were superior to that of the UV-cured films with butyl acrylate as diluent to prepare UV-curing coating.
文摘To reduce the impact of the novel SARS-CoV-2 virus, popularly known as the Coronavirus, many public health-related rules have been established around the world. Along with social distancing and lockdowns, most countries have mandatory wearing of face masks in public areas to limit the spread of the virus during the COVID-19 pandemic. However, because people are free to choose any method to make their masks, some are being fabricated from materials that can be toxic to the environment and human health. This paper discusses how inks and dyes used in face masks are causing major environmental degradation and health issues in industry workers and the general mask-wearing public. The goal fixed for the present study is to raise the alarm with authorities and decision-makers regarding the toxic nature of some colors (dyes and inks) and fabrics in the masks being worn every day.
文摘Precursor (Metal-organic decomposition (MOD)) inks are used to fabricate 2D and 3D printed conductive structures directly onto a substrate. By formulating a nanoalloy structure containing multiple metals, the opportunity to modify chemical and physical properties exists. In this paper, a copper-nickel bimetallic nanoalloy film was fabricated by mixing copper and nickel precursor inks and sintering them in vacuum. The individual elemental inks were formulated and characterized using SEM, EDS, and XRD. During thermal processing, elemental copper forms first and is followed by the formation of bimetallic copper-nickel alloy. The encapsulation of the underlying copper by the nickel-rich alloy provides excellent oxidation resistance. No change in film resistance was observed after the film was exposed to an oxygen plasma. Nanoalloy films printed using reactive metallic inks have a variety of important applications involving local control of alloy composition. Examples include facile formation of layered nanostructures, and electrical conductivity with oxidative stability.
基金Funded by the Natural Science Foundation of Jiangxi Province(20142BAB206029)
文摘A novel UV-curable oligmer 1,4-cyclohexanedimethanol glycidyl ether acrylate（CHDMGEA） was synthesized by utilizing 1,4-cyclohexanedimethanol glycidyl ether（CHDMGE） and acrylic acid（AA） as starting materials, triphenyl phosphine as catalyst and p-hydroxyanisole as inhibitor. The optimum synthetic conditions were that the concentration of triphenyl phosphine was 0.90% of reactants by weight, the concentration of p-hydroxyanisole was 0.20% of reactants by weight, the reaction temperature was 90-100 ℃, and the molar ratio of CHDMGE to AA was 0.5：1.1. The experimental results show that CHDMGEA is a kind of good UV-curable oligmer. The impact resistance of the UV-cured films with CHDMGEA as oligmer to prepare UV-curing coating was superior to that of the UV-cured films with bisphenol A diglycidyl ether diacrylate（BPGEA） as oligmer to prepare UV-curing coating.
基金supported by the National High-Technology Research and Development Program of China (Grant No.2002AA6Z3083)
文摘A novel UV-curable prepolymer neopentyl glycol diglycidyl ether diacrylate (NPGGEA) was synthesized by using neopentyl glycol diglycidyl ether (NPGGE) and acrylic acid (AA) as starting materials, N, N-dimethylbenzylamine as catalyst and p-hydroxyanisole as inhibitor. The optimum synthetic conditions were taken as follows: The concentration of N,N-dimethylbenzylamine, 0.80% of reactants; the concentration of p-hydroxyanisole, 0.3% of reactants; the reaction temperature, 90-110 ; the molar ratio of NPGGE to AA, 1:2.2. Meanwhile, 1-hydroxycyclohexyl phenyl ketone of a UV-cured initiator was added to the synthesized NPGGEA to prepare a kind of UV-cured coating. Mechanical properties of the UV-cured films were determined, giving 28.75 MPa of tensile strength, 923.82 MPa of Young’s modulus and 5.51% of elongation at tear.
文摘This work describes the application of a detailed set of TXRF evaluations to the elemental content of assorted tattoo inks, on the market of the city of Concepcion, Chile. We applied TXRF as a screening method for determining the composition in 3 sets of tattoo inks, in order to establish, from an inorganic point of view, the composition and purity of the samples, evaluating their elemental innocuousness. The analyzed 48 products were freely acquired from on line suppliers. All of them were analyzed by external standard quantification, but in order to inter-compare the results, a 15% of the samples were acidly digested and then quantified by the internal standard method. In the samples we determined: 1) their inorganic quantitative composition and, 2) the possible presence of elements which are potential health hazards. In this study few anomalies were found: 1) The high presence Ti of and W in few samples, 2) Arsenic was found in four of them, and 3) A trace detection of a rare earth element in a particular product. The products studied are almost freely imported from a world open marked, so the questions about their innocuousness could affect not only to the Chilean society.
