Experimental study on Ti+Nb bearing ultra-low carbon bake hardening sheet steel hot-rolled in the ferrite region

A Ti＋Nb bearing ultra-low carbon bake hardening sheet steel hot-rolled in the conventional austenite region and in the ferrite region with lubrication was experimentally studied. Subsequent cold rolling and continuous annealing processes were also conducted. The results show that microstructures of ultra-low carbon bake hardening hot strips at room temperature are basically irregular polygonal ferrites. The yield strength, ultimate tensile strength, n value, and r value of the No.2 specimen hot-rolled in the ferrite region with lubrication are 243 MPa, 364 MPa, 0.29, and 1.74, respectively, which are similar to those of the No.1 specimen hot-roiled in the conventional austenite region. The elongation rate and bake hardening value of No.2 specimen are 51% and 49.4 MPa, respectively, which are greater than those of No. 1 specimen. The No.2 specimen hot-rolled in the ferrite region with lubrication exhibits good mechanical properties and relatively excellent baking hardening performance. Therefore, the hot rolling experiment of Ti＋Nb bearing ultra-low carbon bake hardening steel in the ferrite region with lubrication is feasible and can be considered in the future industrial trial production.

Effect of temper rolling on the bake-hardening behavior of low carbon steel

In a typical process, low carbon steel was annealed at two different temperatures （660℃ and 750℃）, and then was temper rolled to improve the mechanical properties. Pre-straining and baking treatments were subsequently carried out to measure the bake-hardening （BH） values. The influences of annealing temperature and temper rolling on the BH behavior of the steel were investigated. The results indicated that the microstructure evolution during temper rolling was related to carbon atoms and dislocations. After an apparent increase, the BH value of the steel significantly decreased when the temper rolling reduction was increased from 0%to 5%. This was attributed to the increase in solute carbon concentration and dislocation density. The maximum BH values of the steel annealed at 660℃ and 750℃ were 80 MPa and 89 MPa at the reductions of 3%and 4%, respectively. Moreover, increasing the annealing temperature from 660 to 750℃ resulted in an ob-vious increase in the BH value due to carbide dissolution.

Decarburization rate of RH refining for ultra low carbon steel

The decarburization behaviors of ultra low carbon steel in a 210-t RH vacuum degasser were investigated under practical operat- ing conditions. According to the apparent decarburization rate constant （Kc） calculated by the carbon content in the samples taken from the hot melt in a ladle at an interval of 1-2 min, it is observed that the total decarburization reaction period in RH can be divided into the quick decarburization period and the stagnant decarburization period, which is quite different from the traditional one with three stages. In this study, the average apparent decarburization rate constant during the quick decarburization period is 0.306 min^-1, and that of the stagnant period is 0.072 min^-1. Increasing the initial carbon content and enhancing the exhausting capacity can increase the apparent decarburization rate constant in the quick decarburization period. The decarburization reaction comes into the stagnant decarburization period when the carbon content in molten steel is less than 14× 10^-6 after 10 min of decarburization.

Novel mechanism for the modification of Al_2O_3-based inclusions in ultra-low carbon Al-killed steel considering the effects of magnesium and calcium

Many researchers have explored the inclusion modification mechanism to improve non-metallic inclusion modifications in steelmaking. In this study, two types of industrial trials on inclusion modifications in liquid steel were conducted using ultra-low-carbon Al-killed steel with different Mg and Ca contents to verify the effects of Ca and Mg contents on the modification mechanism of Al_2O_3-based inclusions during secondary refining. The results showed that Al_2O_3-based inclusions can be modified into liquid calcium aluminate or a multi-component inclusion with the addition of a suitable amount of Ca. In addition, [Mg] in liquid steel can further reduce CaO in liquid calcium aluminate to drive its evolution into CaO–MgO–Al_2O_3 multi-component inclusions. Thermodynamic analysis confirmed that the reaction between [Mg] and CaO in liquid calcium aluminate occurs when the MgO content of liquid calcium aluminate is less than 3 wt% and the temperature is higher than 1843 K.

Structure Character of M-A Constituent in CGHAZ of New Ultra-Low Carbon Bainitic Steel under Laser Welding Conditions

800 MPa grade new ultra-low carbon bainitic （NULCB） steel is the recently developed new generation steel. The microstructure in the coarse-grained heat affected zone （CGHAZ） of NULCB steel under laser welding conditions was investigated by thermal simulation. The influence of the cooling time from 800℃ to 500℃.t8/5 （0.3-30 s）, on the microstructure of the CGHAZ was discussed. The experimental results indicate that the microstructnre of the CGHAZ is only the granular bainite which consists of bainitic ferrite （BF） lath and M-A constituent while t8/5 is 0.3-30 s. The M-A constituent consists of twinned martensite and residual austenite, and the change of the volume fraction of the residual austenite in the M-A constituent is very small when t8/5 is between 0.3 and 30 s. The morphology of the M-A constituent obviously changes with the variation of t8/5.As t8/5 increases, tile average width, gross and shape parameter of the M-A constituent increase, while the line density of the M-A constituent decreases.

Mathematical Model of Decarburization of Ultra Low Carbon Steel during RH Treatment

According to the balance of carbon and oxygen, a decarburization model for the RH treatment has been developed. in which the influence of the mass transfer of carbon and oxygen in the liquid steel and the stirring energy (ε) in the vacuum vessel on decarburization rate has been considered. The conclusion that the volumetric coefficients of the mass transfer of carbon is proportional to ε(1.5) is drawn. Industrical experiment proves this model is reliable. The influence of some factors on decarburization rate has been obtained. which can provide directions for RH treatment The decarburization behavior of steel with RH-OB treatment is also studied. The OB-or-not curve, the optimized OB time and OB amount are discussed.

Isothermal precipitation behavior of copper sulfide in ultra low carbon steel

Copper and sulfur are typical residual elements or impurity elements in steel.Sufficient removal of them during steelmaking process is difficult for copper and costly for sulfur.Utilization of copper and sulfur in steel, especially in steel scrap,has been an important issue for a long period for metallurgists.Copper and sulfur may combine to form copper sulfide,which may provide a prospect to avoid the detrimental effects of copper and sulfur in steel.Unfortunately the formation mechanism of copper sulfide in steel has not been completely clarified so far. In the present paper,solution treatment of samples containing copper and sulfur are firstly performed at 1623 K for 2.7×10~3 s followed by quenching into water.The samples are then isothermally heat-treated at 673 K,873 K, 1073 K,1273 K and 1373K for different time followed by quenching into water again.The size,morphology, constituent and crystallography of sulfide precipitates in these samples are investigated by scanning electron microscope(SEM) and TEM equipped with EDS.Fine copper sulfides(less than 100 nm) are observed to coexist with silicon oxide in samples even isothermally heat-treated at 1 373 K for 1.44×10~4 s;Film-like copper sulfides are generally observed to co-exist with iron sulfide in all samples;Plate-like copper sulfides are observed especially in sample isothermally heat-treated at 1 073 K for 1.44×10~4 s.The formation mechanisms of these copper sulfides have been discussed.

Advanced manufacturing technologies of large martensitic stainless steel castings with ultra low carbon and high cleanliness

The key manufacturing technologies associated with composition, microstructure, mechanical properties, casting quality and key process control for large martensitic stainless steel castings are involved in this paper. The achievements fully satisfeid the technical requirements of the large 700 MW stainless steel hydraulic turbine runner for the Three Gorges Hydropower Station, and become the major technical support for the design and manufacture of the largest 700 MW hydraulic turbine generator unit in the world developed through our own efforts. The characteristics of a new high yield to tensile strength (R p0.2/R m ) ratio and high obdurability martensitic stainless steel with ultra low carbon and high cleanliness are also described. Over the next ten years, the large martensitic stainless steel castings and advanced manufacturing technologies will see a huge demand in clean energy industry such as nuclear power, hydraulic power at home and abroad. Therefore, the new high yield o tensile strength (R p0.2/R m ) ratio and high obdurability martensitic stainless steel materials, the fast and flexible manufacturing technologies of large size castings, and new environment friendly sustainable process will face new challenges and opportunities.

Effect of an upward magnetic field on nanosized sulfide precipitation in ultra-low carbon steel

An induction levitation melting （ILM） refining process is performed to remove most microsized inclusions in ultra-low carbon steel （UCS）. Nanosized, spheroid shaped sulfide precipitates remain dispersed in the UCS. During the ILM process, the UCS is molten and is rotated under an upward magnetic field. With the addition of Ti additives, the spinning molten steel under the upward magnetic field ejects particles because of resultant centrifugal, floating, and magnetic forces. Magnetic force plays a key role in removing sub-micrometer-sized particles, composed of porous aluminum titanate enwrapping alumina nuclei. Consequently, sulfide precipitates with sizes less than 50 nan remain dispersed in the steel matrix. These findings open a path to the fabrication of clean steel or steel bearing only a nanosized strengthen- ing phase.

Deformation Behavior of Ultra-low Carbon Steel in Ferrite Region during Warm Processing

The hot deformation experiments of ultra-low carbon steel in ferrite range were carried out in a hot simulator in order to research hot deformation behaviors of ultra-low carbon steel in ferrite range at low temperature. The results show that the influences of deformation parameters on flow stress are different to those in austenitic deformation. The deformation characteristic parameters were calculated for ultra-low carbon steel in ferrite region. The flow stress equation for ultra-low carbon steel in ferritic deformation at low temperature was obtained.

Mechanical Method Determining Precipitation in an Ultra-Low Carbon Bainitic Steel

Stress relaxation was chosen as the best method for monitoring the precipitation process. Tests were carried out on an ultra-low carbon bainitic steel containing Mn, Nb and B over 800~950℃. Specimens were solu- tion treated at 1250℃ for a certain holding period. A prestain of 20% was applied at a strain rate of 0.1/s. The exper- imental results are displayed by a set of stress vs. 1g(time) curves different from the typical stress relaxation curves. There are two singularities forming a stress plateau on the stress vs.1g(time) curves when precipitates could be observed. Suppose the first one is the start of precipitation (Ps), and the second represcnts the fihish (Pf). As a result Precipitation-Time-Temperature relationship is described as C-shape curves based on two points. This mechanical method is suitable and precise for measuring precipitates in microalloyed steels during hot working.

Optimum process of RH-MFB refining for ultra-low carbon steel

A mathematical model was established and applied to simulate thedecarburization of RH-MFB process in Pansteel Company. Study of theeffects of w_[C]0, w_[O]0, Ar flowrate, evaluation rate the MFB lanceblowing parameters on the decarburization process was car- Ried out.The results showed that this model could give the quantitativeunderstanding of the process, especially the behavior of MFB Lanceblowing. This model has realized the optimum process of RH-MFBrefining for ultra-low carbon steels in Pansteel.

The micro structure of high carbon low alloy steel for easy drawing

For better processing performance of high carbon low alloy steel wire rod,an investigation about the influence of cementite lamellar spacing on wire 'easy drawing' performance is completed.It is pointed out that too thin cementite lamellar spacing(<80 um) reduces the strain hardening level of wire drawing, and reduce the torsion performance of drawn wire at same time.For the wire or wire rod from industrial production,compared with the micro-structure with troostite,the micro-structure with sorbite or sorbite mixed with pearlite is more suitable to the drawing process with high reduction ratio.

Experimental Procedure and Hardening Model to Consider Forming and Baking Effects in Simulation

This paper investigated an experimental method for bake hardening properties, a technique for deriving the true stress-strain curves after reaching the maximum load, and a constitutive equation considering both work hardening and bake hardening in order to apply the work hardening occurring in the forming process of parts and the bake hardening induced in the baking process to an automotive crash simulation. A general bake hardening test is that a pre-tensioned specimen is baked and then the same specimen is tensioned again without any further treatment. For a bake hardening test of automotive steel with a tensile strength of 1.2 GPa or more, fractures often occur in curvature section outside, an extensometer due to the difference in the material strength caused by non-uniform bake hardening. This causes a problem in that the bake hardening properties cannot be obtained. In this paper, to prevent curvature fracture, tensile specimens were re-machined in the uniformly deformed region of large specimens subjected to pre-strain, and the re-machined specimens with uniform strength in all regions were re-tensioned. In the bake hardening test of ultra-high strength steels with a tensile strength of 1 GPa or more, shear band fractures occur when the pre-strain is large. This makes it impossible to obtain a true stress-strain curve because there is no uniformly deformed region under a tensile test. To overcome this problem, a new method to calculate the true stress-strain curve by comparing experimental results and the load calculated by the local strain obtained from digital images was developed. This method can be applied not only where shear band deformation occurs, but also in necking deformation, and true stress-strain curves for strains up to 2 - 3 times the uniform elongation can be obtained. A new constitutive equation was developed since an appropriate hardening model is required to simultaneously apply the work hardening and the bake hardening to the simulation. For the newly developed model, the user material subroutine of LS-Dyna was configured, and the simulation was performed on the single hat specimens with pre-strain. When both work hardening and bake hardening were considered, there was a significant increase in absorbed energy compared to when only work hardening was considered. This means that both work hardening and bake hardening should be considered in the car crash simulations to enhance the accuracy of the simulation.

Effect of annealing time and phosphorus addition on bake hardening behavior of ultra-low carbon bake hardening steel

The relationship of the P and C grain boundary segregation and its effect on bake hardening behavior were investigated in ultra-low carbon bake hardening (ULC-BH)steel with and without P addition annealed at 810 ℃ for various time using electron probe micro-analyzer,electroh backscattered diffraction,and three-dimensional atomic probe techniques.Results revealed that P addition and annealing duration considerably affected the bake hardening behavior of experimental steel. The BH value of ULC-BH steel without P addition is lower than that with P addition within a short annealing time,and the difference in the BH value gradually decreases as the annealing duration is prolonged.P segregation is dominant in terms of a high P bulk content in steels with P addition at the expense of C segregation during annealing.By contrast,opposite effects are observed in low carbon bake hardening steel.The high residual solute C content in steel with P addition is due to P segregation at the grain boundary.Site competition is mainly responsible for the lower BH value in ULC-BH steel without P addition than that with P addition.As the annealing time is further extended,C segregation begins at grain boundary despite the delayed P segregation,leading to a gradual decrease in the solute concentration in the matrix of steels with P addition.C and P segregations reach the equilibrium as the annealing time increases to 60 min at 810 ℃ in the two steel samples.Theoretical calculations reveal that the residual solute C concentration in the matrix decreases to zero,and this finding is consistent with the change trend of the bake hardening value.Hence,the C segregation at grain boundary. adversely influences the bake hardening property of ULC-BH steel.

钢铁行业大气污染治理科技发展分析与展望

钢铁行业是我国工业领域重要的大气污染排放源之一,钢铁行业的大气污染治理是降低重点行业污染排放、打好污染防治攻坚战的重中之重。近年来,我国在钢铁行业大气污染治理方面取得了显著成果。总结了我国“十一五”以来钢铁行业污染防治科技工作的部署,并梳理分析了钢铁行业大气污染治理技术发展的阶段。基于末端治理、源头减排和过程控制、全过程耦合控制三个方面技术发展现状,剖析了当前我国钢铁行业在多污染物协同深度减排和实现超低排放面临的形势和问题。最后,面向“十四五”时期,聚焦碳达峰碳中和目标,提出了相关建议,旨在深化大气污染防治科技工作,为建设“美丽中国”和实现“双碳”目标提供关键科技支撑。在未来的发展中,我们有理由相信,在全社会的共同努力下,钢铁行业将迎来更加清洁、高效和可持续的发展。

Microstructure and Properties of Ti and Ti+Nb Ultra-Low-Carbon Bake Hardened Steels

Hot rolling, cold rolling and continuous annealing processes of Ti bearing and Ti＋ Nb stabilized ultra-low-carbon bake hardened steels were experimentally studied. The microstructure and texture evolution, as well as the morphology, size and distribution of second phase precipitates during hot rolling, cold rolling and continuous annealing were also analyzed. The results showed that the size of NbC precipitates in Ti＋Nb stabilized ultra-low-carbon bake hardened steel was smaller than that of TiC precipitates in Ti bearing ultra-low-carbon bake hardened steel, which made the average grain size of Ti＋ Nb stabilized ultra-low-carbon bake hardened steel finer than that of Ti bearing ultra-low-carbon bake hardened steel; for the yield strength, the former was higher than the latter; but for the r value which reflects the deep-drawing performance, the former was lower than the latter.

Effect of Continuous Annealing on Microstructure and Bake Hardening Behavior of Low Carbon Steel

The influences of the heating rate, annealing temperature and soaking time during continuous annealing on the microstructure evolution and bake hardening behavior of the low carbon steel were investigated. After 2% pres- training, bake treatment （180 ℃ × 20 min） was carried out to measure BH （bake hardening） values. The results showed that, with the increase of the annealing temperature, the grain size increased except for annealing in the in- tercritical region. Furthermore, the BH value increased and the mean grain size reduced with increasing the heating rate from 5 to 80 ℃/s. The BH value was very low before complete recrystallization. After a significant decrease from 630 to 720 ℃ , the BH value enhanced when the steel was annealed at 750 ℃. With the increase of the soaking time from 20 to 100 s, the BH value reduced linearly due to the segregation of solute C atoms.

变形量对冷拉拔低碳镀锌钢丝力学性能的影响

冷拉拔低碳镀锌钢丝以良好的耐蚀性能、焊接性能、与力学性能协同匹配的良好综合性能和低廉的价格广泛应用于轻工业及建筑行业,其中变形量是影响其力学性能、生产成本及良品率的关键因素。通过显微组织分析、力学性能测定、断口观察,研究了Q235冷拉拔低碳镀锌钢丝不同变形量下的加工硬化过程,并分析了断丝及钢丝表面出现箭头状裂纹的原因。结果表明:真应变从0增加到2.41的过程中,抗拉强度、横纵截面硬度随应变量增加呈抛物线状增加,抗拉强度从586.8 MPa增加到1157.1 MPa,横截面硬度比纵截面增加了5.8 HV。塑性变形初期,加工硬化率最大,为364.7 MPa。真应变从0增加到1.91过程中,加工硬化率从364.7 MPa降低到162.2 MPa,真应变从1.91增加到2.41的过程中,加工硬化率又增加到了172.0 MPa。钢丝中存在CaO夹杂物是导致钢丝出现断丝和表面箭头状裂纹的主要原因。

超低碳IF钢冶炼过程炉渣对夹杂物控制研究进展

超低碳IF钢板主要应用于汽车面板等超深冲部件,其面临的主要质量问题是夹杂物、卷渣、气泡造成的炼钢缺陷,因此全生产流程中所采用的炉渣性质对控制炼钢缺陷具有重要作用。分别从炉渣的物化特性以及所在工序炉渣特性两个角度归纳总结了炉渣对夹杂物控制产生的影响,发现炉渣对夹杂物的吸附溶解与炉渣的物化性质和夹杂物的尺寸相关。RH精炼渣主要控制目标是低氧化性和合适的w(CaO)/w(Al_(2)O_(3)),TFe质量分数一般控制在2.0%~8.0%,w(CaO)/w(Al_(2)O_(3))控制在1.2~1.8,此外精炼渣碱度一般控制较高为4.0~10.0。中间包覆盖剂和结晶器保护渣首先要防止钢液增碳,其次是防止渣中SiO_(2)造成钢液的二次氧化,同时它们还应拥有良好的吸附夹杂物的能力。超低碳IF钢中间包高碱度覆盖剂一般碱度为2.9~11.5,w(CaO)/w(Al_(2)O_(3))控制在1.0~2.5,(FeO+MnO)质量分数控制在1.9%~4.0%。而超低碳IF钢结晶器保护渣的碱度一般控制较低在0.85~1.0,w(CaO)/w(Al_(2)O_(3))控制在5.0~8.5,(FeO+MnO)质量分数小于1%。