Electrokinetic-mechanism of water and furfural oxidation on pulsed laser-interlaced Cu_(2)O and CoO on nickel foam

The electrocatalytic oxidation of biomass-derived furfural(FF)feedstocks into 2-furoic acid(FA)holds immense industrial potential in optics,cosmetics,polymers,and food.Herein,we fabricated Co O/Ni O/nickel foam(NF)and Cu_(2)O/Ni O/NF electrodes via in situ pulsed laser irradiation in liquids(PLIL)for the bifunctional electrocatalysis of oxygen evolution reaction(OER)and furfural oxidation reaction(FOR),respectively.Simultaneous oxidation of NF surface to NiO and deposition of CoO and/or Cu_(2)O on NF during PLIL offer distinct advantages for enhancing both the OER and FOR.CoO/NiO/NF electrocatalyst provides a consistently low overpotential of~359 m V(OER)at 10 m A/cm^(2),achieving the maximum FA yield(~16.37 m M)with 61.5%selectivity,79.5%carbon balance,and a remarkable Faradaic efficiency of~90.1%during 2 h of FOR at 1.43 V(vs.reversible hydrogen electrode).Mechanistic pathway via in situ electrochemical-Raman spectroscopy on CoO/NiO/NF reveals the involvement of phase transition intermediates(NiOOH and CoOOH)as surface-active centers during electrochemical oxidation.The carbonyl carbon in FF is attacked by hydroxyl groups to form unstable hydrates that subsequently undergo further oxidation to yield FA products.This method holds promise for large-scale applications,enabling simultaneous production of renewable building materials and fuel.

Memristive feature and mechanism induced by laser-doping in defect-free 2D semiconductor materials

Memristors as non-volatile memory devices have gained numerous attentions owing to their advantages in storage,in-memory computing, synaptic applications, etc. In recent years, two-dimensional(2D) materials with moderate defects have been discovered to exist memristive feature. However, it is very difficult to obtain moderate defect degree in 2D materials, and studied on modulation means and mechanism becomes urgent and essential. In this work, we realized memristive feature with a bipolar switching and a configurable on/off ratio in a two-terminal MoS_(2) device(on/off ratio ~100), for the first time, from absent to present using laser-modulation to few-layer defect-free MoS_(2)(about 10 layers), and its retention time in both high resistance state and low resistance state can reach 2×10^(4) s. The mechanism of the laser-induced memristive feature has been cleared by dynamic Monte Carlo simulations and first-principles calculations. Furthermore, we verified the universality of the laser-modulation by investigating other 2D materials of TMDs. Our work will open a route to modulate and optimize the performance of 2D semiconductor memristive devices.

Investigations on MoS_(2)plasma by infra-red pulsed laser irradiation in high vacuum

MoS_(2)targets were irradiated by infra-red(IR)pulsed laser in a high vacuum to determine hot plasma parameters,atomic,molecular and ion emission,and angular and charge state distributions.In this way,pulsed laser deposition(PLD)of thin films on graphene oxide substrates was also realized.An Nd:YAG laser,operating at the 1064 nm wavelength with a 5 ns pulse duration and up to a 1 J pulse energy,in a single pulse or at a 10 Hz repetition rate,was employed.Ablation yield was measured as a function of the laser fluence.Plasma was characterized using different analysis techniques,such as time-of-flight measurements,quadrupole mass spectrometry and fast CCD visible imaging.The so-produced films were characterized by composition,thickness,roughness,wetting ability,and morphology.When compared to the MoS_(2)targets,they show a slight decrease of S with respect to Mo,due to higher ablation yield,low fusion temperature and high sublimation in vacuum.The pulsed IR laser deposited Mo Sx(with 1<x<2)films are uniform,with a thickness of about 130 nm,a roughness of about 50 nm and a higher wettability than the MoS_(2)targets.Some potential applications of the pulsed IR laser-deposited Mo Sx films are also presented and discussed.

基于ICESat-2多波束激光测高数据的全球海洋重力异常反演分析

卫星测高技术是获取精细海洋重力数据的重要技术手段之一。常规卫星测高反演海洋重力异常主要是利用沿轨测高数据,而跨轨数据因较长的时间间隔或者稀疏的地面轨间距往往不能用于海洋重力异常反演,进而影响了海洋重力异常模型精度的进一步改善。新型激光测高ICESat-2能够同时获得3对光束观测数据,相邻激光束的地面间距约为3 km,为结合跨轨数据改善海洋重力异常模型提供了可能。本文首先给出了集成沿轨和跨轨数据反演海洋重力异常的处理策略;然后,分别利用沿轨数据和集成的数据构建了ICESat-2全球海洋重力异常模型(IS2Gra_alo和IS2Gra_alo_acr),结果表明通过补充跨轨数据能够有效提高沿轨数据反演海洋重力异常的精度,并验证了ICESat-2测高数据反演全球海洋重力异常的可靠性。此外,本文还探讨了ICESat-2不同跨轨数据组合对海洋重力异常模型反演精度的影响,在沿轨数据的基础上集成适当距离的跨轨观测数据能够有利于改善海洋重力异常模型的精度。本文研究为后续SWOT宽刈幅测高数据和我国双星跟飞模式测高数据反演海洋重力异常模型提供了参考意义。

Cr_(3)C_(2)对激光熔覆原位生成WC增强颗粒粒度及涂层性能的影响

为了研究 Cr_(3)C_(2)对原位生成WC增强相粒度的抑制作用及对涂层性能的影响,在H13钢表面制备了 Cr_(3)C_(2)含量为0、1%、1.5%、2%、2.5%的WC增强镍基涂层。采用扫描电镜(SEM)分析涂层的显微组织,比较WC粒度变化情况以及涂层不同形态区域的元素分布;采用X射线衍射仪(XRD)分析涂层的物相组成;采用显微硬度计分析涂层的硬度值;采用摩擦磨损试验机对涂层的摩擦磨损性能进行测试。结果表明: Cr_(3)C_(2)能够显著抑制WC颗粒的长大,但存在一个最佳值, Cr_(3)C_(2)抑制WC晶粒生长的主要原因是 Cr_(3)C_(2)能够降低WC在粘结相的溶解度。随着 Cr_(3)C_(2)的加入,涂层中含铬物质增多,涂层显微硬度也随之增大,当 Cr_(3)C_(2)含量为2%时涂层显微硬度最大。添加 Cr_(3)C_(2)抑制剂的涂层摩擦磨损性能也更优,磨损机理主要为粘着磨损。

点阵CO_(2)激光Deep FX+Active FX模式治疗痤疮瘢痕疗效观察

目的:探究点阵CO_(2)激光Deep FX+Active FX模式治疗痤疮瘢痕疗效。方法:选取笔者医院2020年1月-2022年1月收治的116例痤疮瘢痕患者作为研究对象,按照随机数字表法分为观察组(采用点阵CO_(2)激光Deep FX+Active FX模式治疗)58例和对照组(采用点阵CO_(2)激光Deep FX模式治疗)58例。观察两组患者治疗后的临床疗效、瘢痕情况、疼痛与瘙痒情况、面部皮肤相关指数、不良反应。结果:观察组总有效率为96.55%,高于对照组86.21%(P<0.05)。治疗后,观察组患者的色泽、血管分布、厚度、柔软度评分均低于对照组(P<0.05)。治疗后,两组疼痛情况评分比较,差异无统计学意义(P>0.05);观察组瘙痒情况评分低于对照组(P<0.05)。观察组红斑指数、棕色斑指数、紫外线光斑指数、毛孔指数、纹路指数及斑点指数均低于对照组(P<0.05)。两组不良反应发生情况比较,差异无统计学意义(P>0.05)。结论:点阵CO_(2)激光Deep FX+Active FX模式能够提高痤疮瘢痕患者的临床疗效,改善瘢痕情况,降低瘙痒情况与面部皮肤相关指数,值得临床推广。

Cr_(3)C_(2)对激光选区熔化316L合金组织及力学性能的影响

目的研究添加Cr_(3)C_(2)颗粒对激光选区熔化316L合金的硬度、强度及耐磨性能的影响。方法采用激光选区熔化(Selective Laser Melting,SLM)技术制备316L合金及10%(质量分数)Cr_(3)C_(2)颗粒增强316L合金(Cr_(3)C_(2)/316L),通过X射线衍射仪(XRD)、光学显微镜(OM)、扫描电子显微镜(SEM)、透射电镜(TEM)、维氏显微硬度计、双立柱电子万能试验机和摩擦磨损试验机分别对2组合金试样的组织结构、硬度、拉伸性能以及耐磨性能进行测试与分析。结果316L合金主要由γ-Fe相组成,Cr_(3)C_(2)/316L合金中除γ-Fe相外,还存在Cr_(23)C_(6)和Cr_(3)C_(2)相。316L和Cr_(3)C_(2)/316L合金的显微组织均由柱状晶和等轴晶组成,Cr_(3)C_(2)/316L的组织中等轴晶比例增多,且组织产生了细化。Cr_(3)C_(2)/316L合金的显微硬度为327HV0.1,相比316L合金(265HV0.1)增加了23%。Cr_(3)C_(2)/316L合金的屈服强度和抗拉强度分别为687 MPa和1029 MPa,较316L合金均提高了约50%。Cr_(3)C_(2)/316L合金的磨损率相比316L合金减小了50%。结论在SLM过程中,由于添加的Cr_(3)C_(2)颗粒在激光选区熔化316L合金过程中所产生的非自发形核和提高过冷度的作用,促使了316L合金组织发生明显细化和等轴化。添加的Cr_(3)C_(2)颗粒所产生的细晶强化、沉淀强化和固溶强化作用,使316L合金的硬度、强度和耐磨性都得到有效提升。

重组贻贝粘蛋白在点阵CO_(2)激光治疗面部痤疮萎缩性瘢痕术后创面修复中的应用研究

目的:探究重组贻贝粘蛋白水凝胶敷料(Recombined mussel adhesive protein hydrogel dressing,Rmaphd)在点阵CO_(2)激光治疗面部痤疮萎缩性瘢痕术后创面修复中的应用效果。方法:选择2022年6月-2023年2月面部痤疮萎缩性瘢痕患者117例,分为Rmaphd组、重组人表皮生长因子(Recombinant human epidermal growth factor,rhEGF)组和对照组,每组39例,三组均给予点阵CO_(2)激光术治疗,术后分别给予Rmaphd、rhEGF及生理盐水处理,比较三组疗效、ECCA评分、症状持续时间以及生活质量评分。结果:Rmaphd组和rhEGF组总有效率分别为92.31%和94.87%,均高于对照组76.92%(P<0.05),术后ECCA评分低于对照组(P<0.05),术后疼痛、红斑、痂皮持续时间短于对照组(P<0.05),Acne-QoL各指标得分优于对照组(P<0.05);上述各临床Rmaphd组与rhEGF组差异无统计学意义(P>0.05)。结论:Rmaphd用于点阵CO_(2)激光治疗面部痤疮萎缩性瘢痕术后创面修复疗效显著,具备在临床上辅助激光治疗术后修复的应用潜力。

点阵CO_(2)激光联合米诺地尔治疗雄激素性脱发的疗效及安全性分析

目的:探究点阵CO_(2)激光联合米诺地尔治疗雄激素性脱发(Androgenetic alopecia,AGA)的疗效及安全性分析。方法:选取2020年1月-2021年12月笔者医院收治的114例雄激素性脱发患者,采用单双球法随机分为对照组(n=57)和观察组(n=57),对照组给予米诺地尔治疗,观察组给予点阵CO_(2)激光与米诺地尔联合治疗。比较治疗6个月后两组患者的临床症状改善情况,对比治疗前和治疗6个月后两组患者治疗效果、毛发镜评价、生活质量[流调中心抑郁表(The center for epidemiological studies depression scale,CES-D)、皮肤病生活质量指数(Dermatology life quality index,DLQI)],记录治疗期间不良反应发生情况。结果:治疗6个月后,观察组临床症状改善评分高于对照组(P<0.05);两组脱发评分、新生发评、毳毛比例、CES-D、DLQI评分均较治疗前降低,观察组低于对照组(P<0.05);两组毛发密度、毛囊密度均较治疗前增大,观察组大于对照组(P<0.05);两组患者不良反应差异无统计学意义(P>0.05)。结论:点阵CO_(2)激光联合米诺地尔可改善AGA患者瘙痒、出油、头屑、毛囊炎等症状及毛发镜指标,改善患者生活质量,且不增加不良反应发生率。

Research on Infrared Emissivity and Laser Reflectivity of Sn_(1−x)Er_(x)O_(2)Micro/Nanofibers Based on First-Principles

Sn_(1−x)Er_(x)O_(2)(x=0%,8%,16%,24%)micro/nanofibers were prepared by electrospinning combined with heat treatment using erbium nitrate,stannous chloride and polyvinylpyrrolidone(PVP)as raw materials.The target products were characterized by thermogravimetric analyzer,X-ray diffrotometer,fourier transform infrared spectrometer,scanning electron microscope,spectrophotometer and infrared emissivity tester,and the effects of Er^(3+)doping on its infrared and laser emissivity were studied.At the same time,the Sn_(1−x)Er_(x)O_(2)(x=0%,16%)doping models were constructed based on the first principles of density functional theory,and the related optoelectronic properties such as their energy band structure,density of states,reflectivity and dielectric constant were analyzed,and further explained the mechanism of Er^(3+)doping on SnO_(2)infrared emissivity and laser absorption from the point of electronic structure.The results showed that after calcination at 600℃,single rutile type SnO_(2)was formed,and the crystal structure was not changed by doping Er^(3+).The calcined products showed good fiber morphology,and the average fiber diameter was 402 nm.The infrared emissivity and resistivity of the samples both decreased first and then increased with the increase of Er^(3+)doping amount.When x=16%,the infrared emis-sivity of the sample was at least 0.71;and Er^(3+)doping can effectively reduce the reflectivity of SnO_(2)at 1.06μm and 1.55μm,when x=16%,its reflectivity at 1.06μm and 1.55μm are 50.5%and 40%,respectively,when x=24%,the reflectivity at 1.06μm and 1.55μm wavelengths are 47.3%and 42.1%,respectively.At the same time,the change of carrier concentration and electron transition before and after Er^(3+)doping were described by first-principle calculation,and the regulation mechanism of infrared emissivity and laser reflectivity was explained.This study provides a certain experimental and theoretical basis for the development of a single-type,light-weight and easily prepared infrared and laser compatible-stealth material.

LD端面泵浦Tm:SrF_(2)电光调Q激光器

高掺杂浓度的Tm^(3+)增益介质能通过交叉弛豫过程提高激光器的量子效率,但同时也会增加能量上转换带来的损耗,从而限制激光器效率的进一步提升。对Tm:SrF_(2)晶体的荧光特性以及激光性能展开研究。在激光二极管(LD)端面泵浦下,实现最大功率2.99 W的自由运转输出,激光器的泵浦阈值为0.89 W,中心波长1851 nm,斜效率高达82.1%。采用KTP电光调Q开关演示了Tm:SrF_(2)激光器的电光调Q输出特性。在500 Hz重复频率下,获得了1.02 mJ的最大单脉冲能量,泵浦阈值为2.01 W,最短脉冲宽度为45 ns,对应峰值功率为22.67 kW。实验结果表明,基于LD泵浦的Tm:SrF_(2)激光器具有非常高的效率,有望成为中红外光学参量振荡器(OPO)和光学参量放大器(OPA)的理想泵浦源。

Mid-infrared lightly Er^(3+)-doped CaF_(2)laser under acousto–optical modulation

A 1.7-at.%Er:CaF_(2)crystal was synthesized by temperature gradient method.The Er:CaF_(2)crystal was applied in acousto-optically Q-switched laser at mid-infrared region for the first time.Using a Te O_(2)-based crystal as Q-switcher,we obtained a laser diode(LD)end-pumped Er:CaF_(2)laser with the highest single pulse energy up to 0.49 mJ and maximum peak power of 0.56 kW under 6.34-W absorbed pump power.The implication of these results is that the low-doped Er:CaF_(2)crystal exhibits promising optical properties in solid-state lasers.

La_(2)O_(3)掺杂铁基记忆合金涂层组织与性能研究

为了探究La_(2)O_(3)对激光熔覆形状记忆合金涂层组织和性能的影响,采用宽带激光熔覆技术在42CrMo中碳钢表面制备了掺杂La_(2)O_(3)的Fe17Mn5Si10Cr5Ni形状记忆合金复合涂层,通过表征得到了La_(2)O_(3)对复合涂层的显微组织、维氏硬度、耐磨性、耐蚀性和表面残余应力的影响结果。结果表明,La_(2)O_(3)显著降低了晶粒尺寸,掺杂质量分数w=0.009时,晶粒尺寸达到最小值3.03μm,而复合涂层具有最大硬度454.7 HV 0.2,磨损量最低;并得到最低的自腐蚀电流为4.287×10^(-7)A/cm^(2),最高的自腐蚀电位为-0.843 V,涂层保护率达到94.83%,La_(2)O_(3)明显提高了涂层的耐腐蚀性能;此时涂层的残余应力由拉应力转变为压应力,并在Fe-Mn-Si/La_(2)O_(3)产生的最大残余压应力值为-378 MPa。此项研究为低应力高性能激光熔覆涂层的开发和推广提供了实践参考。

高压强下2μm波段CO_(2)宽光谱吸收测量与分析

利用宽带可调谐掺铥光纤激光器开展了覆盖152 kPa至932 kPa的2µm波段CO_(2)宽光谱吸收测量实验,通过将实测谱与基于HITRAN数据库计算的理论谱进行峰值匹配完成了波长定标,然后将基线表示为三次多项式并结合理论光谱数据,对原始信号做基线-吸收线整体拟合得到了与实验参数设置相吻合的压强、温度和CO_(2)浓度信息。其中压强计算误差低于5%,温度计算误差低于1%,实测谱与理论谱的整体残差在0.04以内。另外对比了窄带吸收谱与宽带吸收谱的吸收面积反演结果,验证了宽光谱吸收技术在高压测量环境下的可靠性,在温度、气体摩尔分数近似不变的情况下,宽带吸收谱反演的吸收面积与压强在测量范围内保持了良好的线性关系。

Behavior of vapor/plasma within the keyhole and above the workpiece during CO_2 laser penetration welding

In this paper, a high-speed camera and an optical emission monitor were used to study the behavior of vapor/ plasma during CO2 laser welding of SUS304 stainless steel. Results of optical emission from vapor/plasma show that two characteristic frequency bands exist, 100 -500 Hz and 1 500 -3 500 Hz. At the same time, the changing images of vapor/ plasma and bottom pool also confirm that there are two different fluctuation frequency bands. One of the frequency bands represents the characteristic of vapor/plasma within the keyhole, and it is within 167 -500 Hz. Another frequency band is within 1 500 - 3 500 Hz, and it obviously derives from the shielding gas. Some factors may cause these frequency differences between the keyhole plasma and the shielding gas plasma. One of them is that the vapor/plasma pressure within the keyhole will increase slowly.

A study on the porosity of CO_2 laser welding of titanium alloy

The CO2 laser welding of BT20 titanium alloy and Ti-23Al-17Nb titanium aluminide was conducted to investigate into the porosity in titanium alloy weld. The results show that there are two sorts of porosities observed in welds of titanium alloy laser welding based on the microscopic characteristics of the porosities. One is the metallurgical porosity with round and smooth inner wall, which results from the surface contamination. The other is the processing porosity with irregular and rough inner wall that displays the trace of the pool flowing, which results from the ruffle on the keyhole wall gathering together locally and closing down the gas in the keyhole into bubbles because of the keyhole fluctuating. The CO2 laser welding could break down easily the surface oxide film and produce little metallurgical porosity, but produces easily processing porosity when partial penetration or unstable-full penetration laser welding is conducted, which always occurs in the center of weld.

Macrostructural and microstructural features of 1000 MPa grade TRIP steel joint by CO_2 laser welding

Bead-on-plate CO2 laser welding of 1 000 MPa grade transformation induced plasticity （TRIP） steel was conducted under different welding powers, welding speeds and shield gases. The macrostructural and microstructural features of the welded joint were investigated. The increase of welding speed reduced the width of the weld bead and the porosities in the weld bead resulting from the different flow mode of melted metal in weld pool. The decrease of welding power or use of shield gas of helium also contributed to the reduction of porosity in the weld bead due to the alleviation of induced plasma formation, thus stabilizing the keyhole. The porosity formation intimately correlated with the evaporation of alloy element Mn in the base metal. The laser welded metal had same martensite microstructure as that of water-quenched base metal. The welding parameters which increased cooling rate all led to fine microstructures of the weld bead.

脉冲激光沉积过程中TiO_(2)等离子体状态诊断及薄膜特性的研究

脉冲激光沉积技术由于具有较高的沉积速率和良好的兼容性,已广泛应用于各种纳米薄膜材料的制备.探究激光等离子体状态与沉积薄膜特性之间的关系,有助于进一步调控与优化脉冲激光技术对薄膜材料的沉积.本文将等离子体状态诊断与沉积薄膜性能相结合,讨论了不同脉冲激光能量下等离子体状态对沉积薄膜性能的影响.结果表明,低烧蚀能量下产生的等离子体更有助于获得质地更好,且与靶材晶相一致的优良薄膜材料.该结果也为探索和调控沉积过程提供参考.

Experimental Research on Plasma Induced by TEA CO_2 Laser Propulsion

Results in the air-breathing propulsion experiments with a parabolic light craft and a self-made UV-preionized 100 J TEA CO2 laser device are presented. Air disturbance and the spectrum of the plasma after the interaction of pulsed laser radiation with the light craft were studied. It was found that the focal length of the parabolic light craft had a significant effect on the air-disturbance. Two shock waves were detected for the longer focal length, while only one shock wave detected for the short focal length. The spectrum of the laser-induced plasma, the distribution of the characteristic lines, and the temporal behaviors of the air plasma were studied in detail. The results showed that, the evolution of the laser-induced plasma lasted 20μs, and the plasma spectrum would reach the maximum intensity at 7μs.

一种基于ICESat-2激光光子与SRTM数据的冰川高程变化误差稳健估计方法

针对利用ICESat-2星载光子点云数据进行冰川高程变化监测时,不同地形条件下的ICESat-2激光光子数据质量差异较大导致冰川高程变化量估算误差较大的问题,本文以青藏高原上中国最大的海洋性冰川——恰青冰川为例,联合使用ICESat-2激光测高数据及30 m分辨率SRTM的DEM产品,提出了融合稳健估计准则的多函数拟合冰川高程变化量估算误差改正模型,降低了因地形坡度引起的冰川高程变化量估算误差;进而,估算了2000—2021年间恰青冰川的高程变化速度及质量变化量。结果表明,与对应的传统最小二乘估计结果相比,本文提出的融合稳健估计的函数模型改正效果更优。随后,将改正结果与多种数据进行交叉验证,能够证明该误差改正模型的有效性和可行性。因此,该模型可以有效改善冰川高程和质量变化信息提取的精度,研究结果表明,研究区21年间冰川高程变化速率约为(-0.52±0.56)m·a^(-1),冰川质量变化约为-12773.81×10^(5)t。此外,经过对21年间气象数据的年变化和月变化分析可知,气温和降水量等因素是引起冰川高程变化的主要动因。