With the rapid development of ocean technology, the deep-sea manned submersible is regarded as a high-tech equipment for the exploration and exploitation of ocean resources. The safety of manned cabin has a decisive e...With the rapid development of ocean technology, the deep-sea manned submersible is regarded as a high-tech equipment for the exploration and exploitation of ocean resources. The safety of manned cabin has a decisive effect on the whole system. Ti-6 Al-4 V with the superior strength-to-weight ratio and corrosion resistance has been used for the manned cabin. The manned cabin experiences loading spectrum with different maximum stresses and different dwell time during their service life. The load sequence effects on dwell fatigue crack growth behavior of Ti-6 Al-4 V under different dwell time are investigated experimentally in this paper. The experimental results show that the crack tip plastic zone is enlarged by the dwell time and the overload retardation zone increases with dwell time under the same overload rate. A dwell fatigue crack growth model is proposed by modifying the crack tip plastic zone under the loading history with combinations of the single overload and dwell time factors are included in the modified model. Based on the experimental data, the overload retardation zone and the crack growth rates of Ti-6 Al-4 V are predicted by the modified model. A reasonable model for the load sequence effect on the dwell fatigue crack growth rates of Ti-6 Al-4 V is verified.展开更多
The low cycle fatigue strength properties of the additively manufactured Ti-6Al-4V alloy are experimentally investi-gated under proportional and nonproportional multiaxial loading.The fatigue tests were conducted usin...The low cycle fatigue strength properties of the additively manufactured Ti-6Al-4V alloy are experimentally investi-gated under proportional and nonproportional multiaxial loading.The fatigue tests were conducted using hollow cylinder specimens with and without heat treatments,at room temperature in air.Two fatigue tests were conducted:one for proportional loading and one for nonproportional loading.The proportional loading was represented by a push-pull strain path(PP)and the nonproportional loading by a circle strain path(Cl).The failure lives of the additively manufactured specimens were clearly reduced drastically by internal voids and defects.However,the sizes of the defects were measured,and the defects were found not to cause a reduction in fatigue strength above a critical size.The fracture surface was observed using scanning electron microscopy to investigate the fracture mechanisms of the additively manufactured specimens under the two types of strain paths.Different fracture patterns were recognized for each strain paths;however,both showed retention of the crack propagation,despite the presence of numerous defects,probably because of the interaction of the defects.The crack propagation properties of the materials with numerous defects under nonproportional multiaxial loading were clarified to increase the reliability of the additively manufactured components.展开更多
<div style="text-align:justify;"> Load identification method is one of the major technical difficulties of non-intrusive composite monitoring. Binary V-I trajectory image can reflect the original V-I t...<div style="text-align:justify;"> Load identification method is one of the major technical difficulties of non-intrusive composite monitoring. Binary V-I trajectory image can reflect the original V-I trajectory characteristics to a large extent, so it is widely used in load identification. However, using single binary V-I trajectory feature for load identification has certain limitations. In order to improve the accuracy of load identification, the power feature is added on the basis of the binary V-I trajectory feature in this paper. We change the initial binary V-I trajectory into a new 3D feature by mapping the power feature to the third dimension. In order to reduce the impact of imbalance samples on load identification, the SVM SMOTE algorithm is used to balance the samples. Based on the deep learning method, the convolutional neural network model is used to extract the newly produced 3D feature to achieve load identification in this paper. The results indicate the new 3D feature has better observability and the proposed model has higher identification performance compared with other classification models on the public data set PLAID. </div>展开更多
V型混合机是预混合饲料厂和药厂最常采用的混合机,为了研究不同装载系数和混合时间对预混料混合均匀度的影响,探求V型混合机在添加剂预混料生产中合理的装载系数和最佳的混合时间。采用甲基紫示踪法,以玉米粉为原料,采用两因素随机分组...V型混合机是预混合饲料厂和药厂最常采用的混合机,为了研究不同装载系数和混合时间对预混料混合均匀度的影响,探求V型混合机在添加剂预混料生产中合理的装载系数和最佳的混合时间。采用甲基紫示踪法,以玉米粉为原料,采用两因素随机分组实验设计方案,分为5个装载系数(20%、30%、40%、50%和60%)和3个不同混合时间(8、10、15 m in)对饲料混合均匀度的影响进行研究。结果表明:V型混合机的最佳装载系数为30%,最佳的混合时间为10 m in。展开更多
基金financially supported by the National Natural Science Foundation of China (Grant No. 51709134)the National Key R&D Program of China (Grant No. 2016YFC0300603-02)the Natural Science Foundation of Jiangsu Province (Grant Nos. BK20160559 and BK20170575)。
文摘With the rapid development of ocean technology, the deep-sea manned submersible is regarded as a high-tech equipment for the exploration and exploitation of ocean resources. The safety of manned cabin has a decisive effect on the whole system. Ti-6 Al-4 V with the superior strength-to-weight ratio and corrosion resistance has been used for the manned cabin. The manned cabin experiences loading spectrum with different maximum stresses and different dwell time during their service life. The load sequence effects on dwell fatigue crack growth behavior of Ti-6 Al-4 V under different dwell time are investigated experimentally in this paper. The experimental results show that the crack tip plastic zone is enlarged by the dwell time and the overload retardation zone increases with dwell time under the same overload rate. A dwell fatigue crack growth model is proposed by modifying the crack tip plastic zone under the loading history with combinations of the single overload and dwell time factors are included in the modified model. Based on the experimental data, the overload retardation zone and the crack growth rates of Ti-6 Al-4 V are predicted by the modified model. A reasonable model for the load sequence effect on the dwell fatigue crack growth rates of Ti-6 Al-4 V is verified.
基金Supported by Japan Society for the Promotion of Science KAKENHI(Grant No.18H05256).
文摘The low cycle fatigue strength properties of the additively manufactured Ti-6Al-4V alloy are experimentally investi-gated under proportional and nonproportional multiaxial loading.The fatigue tests were conducted using hollow cylinder specimens with and without heat treatments,at room temperature in air.Two fatigue tests were conducted:one for proportional loading and one for nonproportional loading.The proportional loading was represented by a push-pull strain path(PP)and the nonproportional loading by a circle strain path(Cl).The failure lives of the additively manufactured specimens were clearly reduced drastically by internal voids and defects.However,the sizes of the defects were measured,and the defects were found not to cause a reduction in fatigue strength above a critical size.The fracture surface was observed using scanning electron microscopy to investigate the fracture mechanisms of the additively manufactured specimens under the two types of strain paths.Different fracture patterns were recognized for each strain paths;however,both showed retention of the crack propagation,despite the presence of numerous defects,probably because of the interaction of the defects.The crack propagation properties of the materials with numerous defects under nonproportional multiaxial loading were clarified to increase the reliability of the additively manufactured components.
文摘<div style="text-align:justify;"> Load identification method is one of the major technical difficulties of non-intrusive composite monitoring. Binary V-I trajectory image can reflect the original V-I trajectory characteristics to a large extent, so it is widely used in load identification. However, using single binary V-I trajectory feature for load identification has certain limitations. In order to improve the accuracy of load identification, the power feature is added on the basis of the binary V-I trajectory feature in this paper. We change the initial binary V-I trajectory into a new 3D feature by mapping the power feature to the third dimension. In order to reduce the impact of imbalance samples on load identification, the SVM SMOTE algorithm is used to balance the samples. Based on the deep learning method, the convolutional neural network model is used to extract the newly produced 3D feature to achieve load identification in this paper. The results indicate the new 3D feature has better observability and the proposed model has higher identification performance compared with other classification models on the public data set PLAID. </div>
文摘V型混合机是预混合饲料厂和药厂最常采用的混合机,为了研究不同装载系数和混合时间对预混料混合均匀度的影响,探求V型混合机在添加剂预混料生产中合理的装载系数和最佳的混合时间。采用甲基紫示踪法,以玉米粉为原料,采用两因素随机分组实验设计方案,分为5个装载系数(20%、30%、40%、50%和60%)和3个不同混合时间(8、10、15 m in)对饲料混合均匀度的影响进行研究。结果表明:V型混合机的最佳装载系数为30%,最佳的混合时间为10 m in。
