Oscillatory Dynamics of a Spherical Solid in a Liquid in an Axisymmetric Variable Cross Section Channel

The dynamics of a solid spherical body in an oscillating liquid flow in a vertical axisymmetric channel of variable cross section is experimentally studied.It is shown that the oscillating liquid leads to the generation of intense averaged flows in each of the channel segments.The intensity and direction of these flows depend on the dimensionless oscillating frequency.In the region of studied frequencies,the dynamics of the considered body is examined when the primary vortices emerging in the flow occupy the whole region in each segment.For a fixed frequency,an increase in the oscillation amplitude leads to a phase-inclusion holding effect,i.e.,the body occupies a quasi-stationary position in one of the cells of the vertical channel,while oscillating around its average position.It is also shown that the oscillating motion of a liquid column generates an averaged force acting on the body,the magnitude of which depends on the properties of the body and its position in the channel.The quasi-stationary position is determined by the relative density and size of the body,as well as the dimensionless frequency.The behavior of the body as a function of the amplitude and frequency of fluid oscillation and relative size is discussed in detail.Such findings may be used in the future to control the position of a phase inclusion and/or to strengthen mass transfer effects in a channel of variable cross section by means of fluid oscillations.

Finite element analysis of rolling process for variable cross-section blade

Due to the variation of the blade cross-section, the deformation stress and strain of the workpiece keep changing during the rolling process and the conventional rolling theory is no longer valid. The complexity and diversity of the blade cross-section determine it impossible to establish an universal theoretical model for the rolling process. Finite element analysis(FEA) provides a perspective solution to the prediction. The FEA software DEFORM was applied to discovering the deformation, stress, strain and velocity field of the variable cross-section workpiece, and the effects of friction coefficient and rolling speed during the rolling process. which indicates that the average rolling force at friction coefficient of 0.4 is 6.5% higher than that at 0.12, and the rolling velocity has less effect on the equivalent stress and strain distribution, which would confer instructive significance on the theoretical study as well as the engineering practice.

Principle and Experimental Verification of Caudal-fin-type Piezoelectric-stack Pump with Variable-cross-section Oscillating Vibrator

In the traditional flow-resistance-differential (FRD) type valve-less piezoelectric pump, the generated outflow and pressure are discontinuous because of the inherent periodicity and fluctuation of the pump. To overcome these drawbacks, utilizing the bending vibration of piezoelectric bimorph to drive fluid was conducted. However, our investigation on the current status of this piezoelectric bimorph pump shows that larger driving force and vibration amplitude are required for fluid pumping; the pumping can be realized through the centrifugal force; and the mechanism of fluid pumping is no longer further studied. Based on these cases, the paper designed a piezoelectric-stack pump with variable-cross-section oscillating (VCSO) vibrator by imitating the swing of the caudal-fin of tuna, and the pump is neither the rotating type nor the volumetric type according to the taxonomy. The interaction between the oscillating vibrator and the fluid parcel is firstly analyzed from the viewpoint of momentum conservation, and the analytical expression of pump flow rate is obtained. Then the modal and harmonic response analyses on the vibrator immerged in water are carried out. From the analyses the first two orders resonance frequencies are 832 Hz and 1 939 Hz, respectively, and the peak value of the tip amplitude is 0.6 mm. Laser Doppler vibrometer is used to measure both the frequency and vibration amplitude, and the determined first two orders resonance frequencies are 617 Hz and 1 356 Hz, respectively. The measured tip amplitude reaches to the peak value of 0.3 mm. At last, experimental measurement for the flow rates with different driving frequencies is conducted. The results show that the flow rate can reach 560 mL/min at 1 370 Hz when the pump runs under the backpressure of 30 mm water column. And the flow rate is as much as 560% of that of experiment results carried out by researchers from Brazil. The proposed pump innovates in both theory and taxonomy; in addition, the pump overcomes the drawbacks such as large flow fluctuation and low flow rate in the traditional FRD type pumps, which will help to broaden the application of the valve-less piezoelectric pump.

Analysis of the mass of behind-armor debris generated by RHA subjected to normal penetration of variable cross-section EFP

Analyzing the mass of behind-armor debris (BAD) generated by Rolled Homogeneous Armor (RHA) subjected to normal penetration of variable cross-section Explosively Formed Projectile (EFP) is the purpose of this paper. So theoretical analysis, numerical simulation and experimental data are combined to analyze the influence of variable cross-section characteristic on the time history of crater radius. Moreover the relationships between time history of crater radius (as well as mass of BAD) and the thickness of RHA (from 30mm to 70 mm) and the impact velocity of EFP (1650 m/s to 1860 m/s) are also investigated. The results indicate that: 1) being compared to the variable cross-section characteristic is ignored, the theoretical time history of crater radius is in better agreement with the simulation results when the variable cross-section characteristic is considered;2) being compared to the other three conditions of plug, the theoretical mass of BAD is in the best agreement with the simulation results when the shape of plug is frustum of a cone and the angle between generatrix and bottom is 45- and the axial length of mushroom is considered.

Modeling and analysis of piezoelectric beam with periodically variable cross-sections for vibration energy harvesting

A bimorph piezoelectric beam with periodically variable cross-sections is used for the vibration energy harvesting. The effects of two geometrical parameters on the first band gap of this periodic beam are investigated by the generalized differential quadrature rule （GDQR） method. The GDQR method is also used to calculate the forced vibration response of the beam and voltage of each piezoelectric layer when the beam is subject to a sinusoidal base excitation. Results obtained from the analytical method are compared with those obtained from the finite element simulation with ANSYS, and good agreement is found. The voltage output of this periodic beam over its first band gap is calculated and compared with the voltage output of the uniform piezoelectric beam. It is concluded that this periodic beam has three advantages over the uniform piezoelectric beam, i.e., generating more voltage outputs over a wide frequency range, absorbing vibration, and being less weight.

THE APPROXIMATE ANALYTICAL SOLUTION FOR THE BUCKLING LOADS OF A THIN-WALLED BOX COLUMN WITH VARIABLE CROSS-SECTION

For a thin-walled box column with variable cross-section, the three governing equations for torsional-flexural buckling are ordinary differential equations of the second or fourth order with variable coefficients, so it is very difficult to solve them by means of an analytic method. In this paper, polynomials are used to approximate the geometric properties of cross-section and certain coefficients of the differential equations. Based on the energy principle and the Galerkin's method, the approximate formulas for calculating the flexural and torsional buckling loads of this kind of columns are developed respectively, and numerical examples are used to verify the correctness of the solutions obtained. The results calculated in this paper provide the basis for demonstrating the stability of thin-walled box columns with variable cross-section. This paper is of practical value.

Stability of stratified shear flows in channels with variable cross sections

For the instability problem of density stratified shear flows in sea straits with variable cross sections, a new semielliptical instability region is found. Rurthermore, the instability of the bounded shear layer is studied in two cases： （i） the density which takes two different constant values in two layers and （ii） the density which takes three different constant values in three layers. In both cases, the dispersion relation is found to be a quartic equation in the complex phase velocity. It is found that there are two unstable modes in a range of the wave numbers in the first case, whereas there is only one unstable mode in the second case.

EXACT SOLUTION FOR FINITE DEFORMATION PROBLEMS OF CANTILEVER BEAM WITH VARIABLE SECTION UNDER THE ACTION OF ARBITRARY TRANSVERSE LOADS

This paper deals with finite deformation problems of cantilever beam with variable sec- tion under the action of arbitrary transverse loads.By the use of a method of variable replacement, the nonlinear differential equation with varied coefficient for the problem can be transformed into an equation with variable separable.The exact solution can be obtained by the integration method. Some examples are given in the paper,and the results of these examples show that this exact solution includes the existing solutions in references as special cases.

THE GENERAL SOLUTION FOR DYNAMIC RESPONSE OF NONHOMOGENEOUS BEAM WITH VARIABLECROSSSECTION

In this paper by means of the exact analytic method [1], the general solution fordynamic response of nonhomogeneous beam with variable cross section is obtained un-der arbitrary resonant load and boundary conditions. The problem is reduced to solvea non-positive differential equation. Generally, it is not solved by variational method.By the present method, the general solution for this problem may be written as an ana-lytic form. Hence, it is convenient for structure optimizing problem. In this paper, itsconvergence is proved. Numerical examples are given at the end of the paper. which in-dicates satisfactory results can be obtained.

Inner and outer pressure forming of nickel based super-alloy thin-walled part with variable diameter sections

A novel forming method of nickel based super-alloy thin-walled part with variable diameter sections was proposed by using inner and outer pressure with the visco-elasto-plastic pressure-carrying medium at room temperature,and the principle of the method was provided.Experiments and FE simulations were carried out to analyze the deformation characteristics for the part with larger variable diameter ratio(35%).The results show that visco-elasto-plastic pressure-carrying medium can meet the requirements of the room-temperature deformation condition for nickel based super-alloy sheet.The inner and outer pressure forming with the visco-elasto-plastic pressure-carrying medium can meet the requirements of dimensional accuracy for the thin-walled part with variable diameter sections.The thinning of wall-thickness is less than 4%.This method provides a new approach for near-net shape forming of nickel based super-alloy thin-walled parts with variable diameter sections.

Complex variable solution for boundary value problem with X-shaped cavity in plane elasticity and its application*

A new type of displacement pile, the X-section cast-in-place concrete （XCC） pile, has recently been developed in China. Extensive field tests and laboratory experi- ments are undertaken to evaluate its performance and quantify the non-uniform deforma- tion effect （NUDE） of the X-shaped cross section during installation. This paper develops a simplified theoretical model that attempts to capture the NUDE. Based on the theory of complex variable plane elasticity, closed-form solutions of the stress and displacement for the X-shaped cavity boundary value problem are given. Subsequently, the analytical solution is used to evaluate the NUDE, the concrete filling index （CFI）, and the perimeter reduction coefficient of the XCC pile cross section. The computed results are compared with field test results, showing reasonable agreement. The present simplified theoretical model reveals the deformation mechanism of the X-shaped cavity and facilitates applica- tion of the newly developed XCC pile technique in geotechnical engineering.

地震作用下变截面钢管混凝土单桩动力响应

为了探讨桥梁位于软弱土层时,地震作用下变截面钢管混凝土桩基的动力响应,以翔安大桥为工程背景,利用FLAC3D有限元软件建立地震作用下桩-岩土体-钢管耦合作用的数值模型,研究在不同强度的地震作用下变截面钢管混凝土单桩和变截面普通混凝土单桩桩身加速度、桩身位移、桩身弯矩的动力响应差异.结果表明:变截面钢管混凝土单桩在地震作用下的桩身加速度、加速度放大系数、桩身位移最大值和桩身弯矩变化规律均同变截面普通混凝土单桩类似,但钢管使桩身加速度放大系数降低、桩基抵抗侧向变形能力和抗弯承载力提高.因此,钢管可以显著提升地震作用下桩基的抵抗变形能力和承载力.

液化场地大直径变截面单桩动力响应研究

为研究不同地震动强度下液化场地大直径变截面单桩的动力响应规律,基于振动台试验,选取5010波,在地震动强度0.10g~0.45g作用下,研究液化场地砂土孔压比和大直径变截面单桩桩顶水平位移、桩身弯矩、桩身加速度时程响应及桩基损伤等变化规律.试验结果表明:饱和砂土孔压比随着地震动强度的增大上升明显,地震动强度≥0.30g时,饱和砂土孔压比稳定值在0.9附近,此时砂土完全液化;在0.45g地震动强度作用下,桩身加速度、桩顶水平位移及桩身弯矩均达到最大;桩身不同位置处加速度峰值出现时刻均滞后于输入地震波加速度峰值出现时刻,且桩顶及变截面的加速度响应比桩端的响应更弱;不同地震动强度作用下,桩身弯矩最大值均出现在液化土层和非液化土层分界处,且变截面处弯矩小于土层分界面处;地震动强度达到0.30g时,大直径变截面单桩桩身发生损伤.因此,液化场地下大直径变截面桥梁单桩基础抗震设计时,应该重点考虑饱和砂土层分界处、变截面处的抗弯能力,以确保单桩桩身强度满足抗震要求.

黄土地基阶梯型截面桩承载模型试验与计算

为研究黄土地基阶梯型截面桩的荷载传递机理,通过室内模型试验与有限元计算,分析阶梯型截面桩竖向静荷载下的桩身轴力、桩侧摩阻力、桩顶沉降和桩身不同深度荷载分担比,并探索了变径比对其工作性能的影响,并对其进行优化设计。结果表明:在相同荷载下,阶梯型截面桩的桩顶沉降明显小于等截面桩,当变径比在0.8~0.9时,沉降控制效果最佳,其材料利用率最高;若二者极限承载力相同时,阶梯型截面桩的最高材料利用率为等截面桩的1.06倍。阶梯型截面桩为摩擦型桩,变截面位置土体对桩体具有支承作用,其变径处底面土体能承担部分桩顶荷载。桩侧能够分担更多桩顶荷载,减轻桩端土体承载,当变径比在0.8~0.9时,侧摩阻力发挥程度更高。在桩体用料相同时,与等截面桩相比,阶梯型截面桩能大幅度提高承载能力。

煤层气水平井筒倾斜-水平耦合流动规律影响分析

精确掌握煤层气水平井井筒内气液流动规律,对煤层气水平井的合理开发工艺和设备的选择具有重要意义。基于气液两相流理论采用Fluent软件模拟分析的方法,研究了煤层气水平井段倾斜-水平耦合条件下变状态流动规律。分析结果表明:水平段井筒中,上倾斜段井筒内的流动会加剧井筒内气液两相界面的波动。高气、液量下水平段井筒内持液率在流体流动方向上不断增大,低气、液量下水平段井筒内持液率在流体流动方向上不断减小。上倾段倾斜角小于20°时,倾斜角对水平段平均持液率影响较大;下水平段井筒中,倾斜段井筒的长度和倾斜角会影响水平井筒中假想断面的位置,同一流动条件下,出口上倾井筒的倾斜角越大、长度越大,假想断面位置越远离出口端上倾井筒。研究结果可为煤层气水平井下泵深度等排采工艺设计和优选提供理论依据。

既有RC变截面柱加固前后的力学性能

针对变截面柱加层改造处存在的外力损伤、混凝土强度变低等问题,采用增大截面法、CFRP包裹法及粘钢加固法对构件进行加固并分析其受力性能。结果表明:增大截面法、CFRP加固法及粘钢加固法使原构件轴压承载力分别提升了113%、128%、112%,使侧压承载力分别提升了105%和192%及154%,但在周期荷载作用下粘钢加固法具有较大优势;增大截面法适用于提升变截面柱轴压承载力,CFRP加固适用于提升侧压承载力及轴压承载力,但两者均不适用于提升变截面柱抗震能力。而粘钢加固法相较于前两种方法均具有普适性。

幂函数形式连续变截面梁振动的弯曲固有频率分析

为给变截面变幅杆弯曲振动提供设计依据,该文使用微分方程解析法求解变截面梁固有频率。首先,建立变截面梁模型,其中截面面积和惯性矩均按幂次函数变化。得到变截面梁自由振动时挠度的解析表达式,并获得不同边界条件下梁弯曲振动的固有频率方程。其中惯性矩所对应幂指数与截面面积的幂指数的差值为4时,可得自振频率方程的精确形式;而幂指数差值不等于4时,给出近似解法。其次,对4种具体的变截面梁求解不同边界下的自振频率,并与瑞利-里兹法所得的自振频率解比较。验证精确解法结果的正确性,并发现近似解法结果的相对偏差在5%以内。该解析方法较瑞利-里兹法具有能快速求解的特点,且易于分析截面参数对梁固有频率的影响。由算例可得,边界和其他参数不变时,梁的同阶次无量纲自振频率随着幂次指数的增加而增加。几何参数中仅截面形状参数改变时,随着形状参数的增加,梁的同阶次无量纲自振频率随之减小,但固定-自由梁的第1阶自振频率除外。

震陷场地变截面单桩动力特性与损伤评价

为探明震陷场地变截面单桩动力响应特性与损伤状况,以翔安大桥为工程背景,基于大型振动台试验,开展了0.10g~0.45g地震动强度下变截面单桩动力响应特性的研究,评价分析了变截面单桩损伤程度。结果表明:受桩周软弱土层震陷特性的影响,变截面单桩桩顶水平位移动力响应、桩身加速度动力响应及桩身弯矩动力响应均随地震动强度增大呈增大趋势,桩基基频逐渐减小;变截面单桩弯矩最大值出现在震陷土层分界处,地震动强度为0.30g时,超过了其抗弯承载力;地震动强度为0.20g时,变截面单桩桩顶水平位移、桩身加速度、桩身弯矩显著增大,桩基基频突降。基于系统损伤理论,震陷场地变截面单桩损伤状况分为稳定阶段、加剧损伤阶段、塑性破坏阶段共3个阶段。试验结束后,变截面位置处产生弯曲塑性破坏。

基于视觉检测的智能桥梁检查车设计与分析

针对公路变截面梁的特点,提出了一种基于视觉检测的智能检查车。该智能检查车由车体平台和视觉检测平台组成,既能无人智能快速检测,又能人工定点维修,有效地提高了桥梁养护效率及检查工作的安全性。介绍了车体平台的具体结构设计和视觉检测平台的具体组成,并对智能检测和人工检查做了对比试验分析,结果表明智能检测比人工检查具有更好的病害检测完整性和更高的检测效率。

震陷土层变化下变截面单、群桩动力响应差异

为研究地震动作用下震陷土层厚度不同时大直径变截面单桩与群桩基础的动力响应差异,依托厦门第二东通道翔安大桥,通过振动台模型试验,开展震陷土层厚度30、40、50 cm时,单桩与群桩基础桩周土震陷量、桩顶水平位移、桩身加速度及弯矩动力响应差异研究.结果表明:随着震陷层厚度增大,单桩与群桩基础桩周土震陷量、桩顶水平位移、桩身加速度及弯矩均逐渐增大,且加速度及弯矩在变截面处突变;同一震陷层厚度下,群桩基础桩周土震陷量较单桩大,但群桩基础加速度、桩顶水平位移及桩身弯矩均小于单桩.震陷场地桩基础设计时,应着重考虑变截面单桩与群桩动力响应差异,保证桩基础抗震性能.