Today,it is difficult to further improve the dynamic performance of rail vehicles with conventional passive suspension.Also,simplified vehicle respectively running gear layouts that significantly could reduce vehicle ...Today,it is difficult to further improve the dynamic performance of rail vehicles with conventional passive suspension.Also,simplified vehicle respectively running gear layouts that significantly could reduce vehicle weights are difficult to realize with modern requirements on passenger vibration comfort and wheel and rail wear.Active suspension is a powerful technology that can improve the vehicle dynamic performance and make simplified vehicle concepts possible.The KTH Railway group has,together with external partners,investigated active suspensions both numerically and experimentally for 15 years.The paper provides a summary of the activities and the most important findings.One major project carried out in close collaboration with the vehicle manufacturer Bombardier and the Swedish Transport Administration was the Green Train project,where a 2-car EMU test bench was used to demonstrate different active technologies.In ongoing projects,a concept of single axle-single suspension running gear is developed with active suspension both for comfort improvement and reduced wheel wear in curves.The results from on-track tests in the Green Train project were so good that the technology is now implemented in commercial trains and the simulation results for the single-axle running gear are very promising.展开更多
Next-generation vehicle control and future autonomous driving require further advances in vehicle dynamic state estimation. This article provides a concise review, along with the perspectives, of the recent developmen...Next-generation vehicle control and future autonomous driving require further advances in vehicle dynamic state estimation. This article provides a concise review, along with the perspectives, of the recent developments in the estimation of vehicle dynamic states. The definitions used in vehicle dynamic state estimation are first introduced, and alternative estimation structures are presented. Then, the sensor configuration schemes used to estimate vehicle velocity, sideslip angle, yaw rate and roll angle are presented. The vehicle models used for vehicle dynamic state estimation are further summarized, and representative estimation approaches are discussed. Future concerns and perspectives for vehicle dynamic state estimation are also discussed.展开更多
The performance of the vehicle dynamics stability control system(DSC) is dominated by the accurate estimation of tire forces in real-time.The characteristics of tire forces are determined by tire dynamic states and ...The performance of the vehicle dynamics stability control system(DSC) is dominated by the accurate estimation of tire forces in real-time.The characteristics of tire forces are determined by tire dynamic states and parameters,which vary in an obviously large scope along with different working conditions.Currently,there have been many methods based on the nonlinear observer to estimate the tire force and dynamic parameters,but they were only used in off-line analysis because of the computation complexity and the dynamics differences of four tires in the steering maneuver conditions were not considered properly.This paper develops a novel algorithm to observe tire parameters in real-time controller for DSC.The algorithm is based on the sensor-fusion technology with the signals of DSC sensors,and the tire parameters are estimated during a set of maneuver courses.The calibrated tire parameters in the control cycle are treated as the elementary states for vehicle dynamics observation,in which the errors between the calculated and the measured vehicle dynamics are used as the correcting factors for the tire parameter observing process.The test process with a given acceleration following a straight line is used to validate the estimation method of the longitudinal stiffness;while the test process with a given steering angle is used to validate the estimated value of the cornering stiffness.The ground test result shows that the proposed algorithm can estimate the tire stiffness accurately with an acceptable computation cost for real-time controller only using DSC sensor signal.The proposed algorithm can be an efficient algorithm for estimating the tire dynamic parameters in vehicle dynamics stability control system,and can be used to improve the robustness of the DSC controller.展开更多
The existing research of the integrated chassis control mainly focuses on the different evaluation indexes and control strategy. Among the different evaluation indexes, the comprehensive properties are usually not con...The existing research of the integrated chassis control mainly focuses on the different evaluation indexes and control strategy. Among the different evaluation indexes, the comprehensive properties are usually not considered based on the non-linear superposition principle. But, the control strategy has some shortages on tyre model with side-slip angle, road adhesion coefficient, vertical load and velocity. In this paper, based on belief, desire and intention(BDI)-agent model framework, the TYRE agent, electric power steering(EPS) agent and active suspension system(ASS) agent are proposed. In the system(SYS) agent, the coordination mechanism is employed to manage interdependences and conflicts among other agents, so as to improve the flexibility, adaptability, and robustness of the global control system. Due to the existence of the simulation demand of dynamic performance, the vehicle multi-body dynamics model is established by SIMPACK. And then the co-simulation analysis is conducted to evaluate the proposed multi-agent system(MAS) controller. The simulation results demonstrate that the MAS has good effect on the performance of EPS and ASS. Meantime, the better road feeling for the driver is provided considering the multiple and complex driving traffic. Finally, the MAS rapid control prototyping is built to conduct the real vehicle test. The test results are consistent to the simulation results, which verifies the correctness of simulation. The proposed research ensures the driving safety, enhances the handling stability, and improves the ride comfort.展开更多
A 7 degree-of-freedom (DOF) 4 wheels vehicle dynamics model based on Matlab-Simulink is established,and 7 DOF vehicle dynamics equations in the form of nonlinear state-space standards are given.The characters of the...A 7 degree-of-freedom (DOF) 4 wheels vehicle dynamics model based on Matlab-Simulink is established,and 7 DOF vehicle dynamics equations in the form of nonlinear state-space standards are given.The characters of the electronic throttle and the active braking system have been analyzed.And the electronic throttle model and the active braking system model are built according to the test results respectively.Off-line simulation results indicate that the model is suitable for the vehicle adaptive cruise control system,and both of the electronic throttle and the active braking system work in a reasonable way.An adaptive cruise control (ACC) example illustrates that the model has a good performance in cruise and distance keeping.展开更多
The current research of direct yaw moment control(DYC) system focus on the design of target yaw moment and the distribution of wheel brake force. The differential braking intervention can effectively improve the lat...The current research of direct yaw moment control(DYC) system focus on the design of target yaw moment and the distribution of wheel brake force. The differential braking intervention can effectively improve the lateral stability of the vehicle, however, the effect of DYC can be improved a step further by applying the control of vehicle longitudinal velocity. In this paper, the relationship between the vehicle longitudinal velocity and lateral stability is studied, and the simulation results show that a decrease of 5 km/h of longitudinal velocity at a particular situation can bring 100° increasing of stable steering upper limit. A critical stable velocity considering the effect of steering and yaw rate measurement is defined to evaluate the risk of losing steer-ability or stability. A novel velocity pre-control method is proposed by using a hierarchical pre-control logic and is integrated with the traditional DYC system. The control algorithm is verified through a hardware in-the-loop simulation system. Double lane change(DLC) test results on both high friction coefficient(μ) and low μ roads show that by using the pre-control method, the steering effort in DLC test can be reduced by 38% and 51% and the peak value of brake pressure control can be reduced by 20% and 12% respectively on high μ and low μ roads, the lateral stability is also improved. This research proposes a novel DYC system with lighter control effort and better control effect.展开更多
Based on the aerodynamics and vehicle dynamics, the aerodynamic performances and vehicle dynamic characteristics of two high-speed trains passing each other on the ground, embankment and bridge are studied. Firstly, a...Based on the aerodynamics and vehicle dynamics, the aerodynamic performances and vehicle dynamic characteristics of two high-speed trains passing each other on the ground, embankment and bridge are studied. Firstly, a train aerodynamic model and a vehicle dynamic model are established. Through the simulation of the two models, the pressure waves, aerodynamic forces, and vehicle dynamic responses are obtained. Then, the pressure waves and aero- dynamic forces on different foundations are compared. The results show that the variation trends of pressure wave and aerodynamic forces of trains passing each other on different foundations are almost similar. The peak-to-peak differ- ences in pressure wave and aerodynamic force are below 4% and 3% in three cases in open air. Besides, the differences of security indexes, including coefficient of derailment, wheel unloading rate, the wheelset lateral force, and the wheel- rail vertical force, are below 2% among the three cases; the differences of comfort indexes, including the lateral acceleration and the vertical acceleration, are also below 2%. It is concluded that the dynamic performances of trains pass- ing each other are influenced little by different foundations in open air.展开更多
The need to find alternative urban mobility solutions for delivery and transport has led mobility companies to devote enormous resources for research-based solutions to increase vehicle safety. This paper documents a ...The need to find alternative urban mobility solutions for delivery and transport has led mobility companies to devote enormous resources for research-based solutions to increase vehicle safety. This paper documents a virtual approach to investigate the influences of different load states to the vehicle dynamic of light electric vehicle. A model basing on a three-dimensional </span><span style="font-family:""><span style="font-family:Verdana;">multibody system was used, which consists of five bodies. By applying methods of multibody modelling the generalized equations of motion were generated. To </span><span style="font-family:Verdana;">include the behavior within the contact point between road and vehicle a</span><span style="font-family:Verdana;"> simplified tire models was added. The implementation of the equations allowed a first validation of the model via simulations. In a final modeling step the simulation results were interpreted in respect of plausibility. Afterwards, the model was simulated numerically to investigate different load states of the vehicle, by applying constant steering stimuli and variable velocities. In sum, the investigated model approach is useful to identify safety relevant parameters and shows the effects of load states to the vehicle dynamics. Furthermore, it behaves plausibly regarding general vehicle dynamics. These results prove </span><span style="font-family:Verdana;">the general usability of the model for the development controllers and esti</span><span style="font-family:Verdana;">mators in driver assistances systems.展开更多
A computer software named VDAS (Vehicle Dynamic Analysis Simulation) is presented.Based on the mathematical modelling for a military vehicle as a 3-D dynamic system, the softwarecreates random excitation resulting fro...A computer software named VDAS (Vehicle Dynamic Analysis Simulation) is presented.Based on the mathematical modelling for a military vehicle as a 3-D dynamic system, the softwarecreates random excitation resulting from double side road-surface roughness by statisticalsimulation, and solves for the time series of the system response from the system state equations,and gives out the results in probability statistics as well as performance evaluations.展开更多
Rolling stock manufacturers are finding structural solutions to reduce power required by the vehicles,and the lightweight design of the car body represents a possible solution.Optimization processes and innovative mat...Rolling stock manufacturers are finding structural solutions to reduce power required by the vehicles,and the lightweight design of the car body represents a possible solution.Optimization processes and innovative materials can be combined in order to achieve this goal.In this framework,we propose the redesign and optimization process of the car body roof for a light rail vehicle,introducing a sandwich structure.Bonded joint was used as a fastening system.The project was carried out on a single car of a modern tram platform.This preliminary numerical work was developed in two main steps:redesign of the car body structure and optimization of the innovated system.Objective of the process was the mass reduction of the whole metallic structure,while the constraint condition was imposed on the first frequency of vibration of the system.The effect of introducing a sandwich panel within the roof assembly was evaluated,focusing on the mechanical and dynamic performances of the whole car body.A mass saving of 63%on the optimized components was achieved,corresponding to a 7.6%if compared to the complete car body shell.In addition,a positive increasing of 17.7%on the first frequency of vibration was observed.Encouraging results have been achieved in terms of weight reduction and mechanical behaviour of the innovated car body.展开更多
Active suspension systems(ASSs)have been proposed and developed for a few decades,and have now once again become a thriving topic in both academia and industry,due to the high demand for driving comfort and safety and...Active suspension systems(ASSs)have been proposed and developed for a few decades,and have now once again become a thriving topic in both academia and industry,due to the high demand for driving comfort and safety and the compatibility of ASSs with vehicle electrification and autonomy.Existing review papers on ASSs mainly cover dynamics modeling and robust control;however,the gap between academic research outcomes and industrial application requirements has not yet been bridged,hindering most ASS research knowledge from being transferred to vehicle companies.This paper comprehensively reviews advances in ASSs for road vehicles,with a focus on hardware structures and control strategies.In particular,state-of-the-art ASSs that have been recently adopted in production cars are discussed in detail,including the representative solutions of Mercedes active body control(ABC)and Audi predictive active suspension;novel concepts that could become alternative candidates are also introduced,including series active variable geometry suspension,and the active wheel-alignment system.ASSs with compact structure,small mass increment,low power consumption,high-frequency response,acceptable economic costs,and high reliability are more likely to be adopted by car manufacturers.In terms of control strategies,the development of future ASSs aims not only to stabilize the chassis attitude and attenuate the chassis vibration,but also to enable ASSs to cooperate with other modules(e.g.,steering and braking)and sensors(e.g.,cameras)within a car,and even with high-level decision-making(e.g.,reference driving speed)in the overall transportation system-strategies that will be compatible with the rapidly developing electric and autonomous vehicles.展开更多
This paper presents an integrated control scheme for enhancing the ride comfort and handling performance of a four-wheel-independent-drive electric vehicle through the coordination of active suspension system(ASS)and ...This paper presents an integrated control scheme for enhancing the ride comfort and handling performance of a four-wheel-independent-drive electric vehicle through the coordination of active suspension system(ASS)and anti-lock braking system(ABS).First,a longitudinal-vertical coupled vehicle dynamics model is established by integrating a road input model.Then the coupling mechanisms between longitudinal and vertical vehicle dynamics are analyzed.An ASS-ABS integrated control system is proposed,utilizing an H∞controller for ASS to optimize load transfer effect and a neural network sliding mode control for ABS implementation.Finally,the effectiveness of the proposed control scheme is evaluated through comprehensive tests conducted on a hardware-in-loop(HIL)test platform.The HIL test results demonstrate that the proposed control scheme can significantly improve the braking performance and ride comfort compared to conventional ABS control methods.展开更多
Pneumatic tire modeling and validation have been the topic of several research papers, however, most of these papers only deal with pneumatic passenger and truck tires. In recent years, wheeled-scaled vehicles have ga...Pneumatic tire modeling and validation have been the topic of several research papers, however, most of these papers only deal with pneumatic passenger and truck tires. In recent years, wheeled-scaled vehicles have gained lots of attention as a feasible testing platform, nonetheless up to the authors’ knowledge there has been no research regarding the use of scaled tires and their effect on the overall vehicle performance characteristics. This paper presents a novel scaled electric combat vehicle tire model and validation technique. The pro-line lockdown tire size 3.00 × 7.35 is modeled using the Finite Element Analysis (FEA) technique and several materials including layered membrane, beam elements, and Mooney-Rivlin for rubber. The tire-rim assembly is then described, and the rigid body analysis is presented. The tire is then validated using an in-house custom-made static tire testing machine. The tire test rig is made specifically to test the pro-line tire model and is designed and manufactured in the laboratory. The tire is validated using vertical stiffness and footprint tests in the static domain at different operating conditions including several vertical loads. Then the tire is used to perform rolling resistance and steering analysis including the rolling resistance coefficient and the cornering stiffness. The analysis is performed at different operating conditions including longitudinal speeds of 5, 10, and 15 km/h. This tire model will be further used to determine the tractive and braking performance of the tire. Furthermore, the tire test rig will also be modified to perform cornering stiffness tests.展开更多
Purpose–The safety and reliability of high-speed trains rely on the structural integrity of their components and the dynamic performance of the entire vehicle system.This paper aims to define and substantiate the ass...Purpose–The safety and reliability of high-speed trains rely on the structural integrity of their components and the dynamic performance of the entire vehicle system.This paper aims to define and substantiate the assessment of the structural integrity and dynamical integrity of high-speed trains in both theory and practice.The key principles and approacheswill be proposed,and their applications to high-speed trains in Chinawill be presented.Design/methodology/approach–First,the structural integrity and dynamical integrity of high-speed trains are defined,and their relationship is introduced.Then,the principles for assessing the structural integrity of structural and dynamical components are presented and practical examples of gearboxes and dampers are provided.Finally,the principles and approaches for assessing the dynamical integrity of highspeed trains are presented and a novel operational assessment method is further presented.Findings–Vehicle system dynamics is the core of the proposed framework that provides the loads and vibrations on train components and the dynamic performance of the entire vehicle system.For assessing the structural integrity of structural components,an open-loop analysis considering both normal and abnormal vehicle conditions is needed.For assessing the structural integrity of dynamical components,a closed-loop analysis involving the influence of wear and degradation on vehicle system dynamics is needed.The analysis of vehicle system dynamics should follow the principles of complete objects,conditions and indices.Numerical,experimental and operational approaches should be combined to achieve effective assessments.Originality/value–The practical applications demonstrate that assessing the structural integrity and dynamical integrity of high-speed trains can support better control of critical defects,better lifespan management of train components and better maintenance decision-making for high-speed trains.展开更多
Purpose–This paper aims to obtain the evolution law of dynamic performance of CR400BF electric multiple unit(EMU).Design/methodology/approach–Using the dynamic simulation based on field test,stiffness of rotary arm ...Purpose–This paper aims to obtain the evolution law of dynamic performance of CR400BF electric multiple unit(EMU).Design/methodology/approach–Using the dynamic simulation based on field test,stiffness of rotary arm nodes and damping coefficient of anti-hunting dampers were tested.Stiffness,damping coefficient,friction coefficient,track gauge were taken as random variables,the stochastic dynamics simulation method was constructed and applied to research the evolution law with running mileage of dynamic index of CR400BF EMU.Findings–The results showed that stiffness and damping coefficient subjected to normal distribution,the mean and variance were computed and the evolution law of stiffness and damping coefficient with running mileage was obtained.Originality/value–Firstly,based on the field test we found that stiffness of rotary arm nodes and damping coefficient of anti-hunting dampers subjected to normal distribution,and the evolution law of stiffness and damping coefficient with running mileage was proposed.Secondly stiffness,damping coefficient,friction coefficient,track gauge were taken as random variables,the stochastic dynamics simulation method was constructed and applied to the research to the evolution law with running mileage of dynamic index of CR400BF EMU.展开更多
The effect of rail corrugation on the vertical dynamics of railway vehicle coupled with a curved track is investigated in detail with a numerical method when a wheelset is steadily curving. In the calculation of rail ...The effect of rail corrugation on the vertical dynamics of railway vehicle coupled with a curved track is investigated in detail with a numerical method when a wheelset is steadily curving. In the calculation of rail corrugation we consider the combination of Kalkers rolling contact theory modified, a model of material loss on rail running surface, and a dynamics model of railway vehicle coupled with a curved track. In the establishment of the dynamic model, for simplicity, one fourth of the freight car without lateral motions, namely a wheelset and the equivalent one fourth freight car body above it, is considered. The Euler beam is used to model the rails and the track structure under the rails is replaced with equivalent springs, dampers and mass bodies. The numerical results show the great influence of the rail corrugation on the vibration of the parts of the vehicle and the track, and the some characters of rail corrugation in development.展开更多
Model predictive control(MPC)algorithm is established based on a mathematical model of a plant to forecast the system behavior and optimize the current control move,thus producing the best future performance.Hence,mod...Model predictive control(MPC)algorithm is established based on a mathematical model of a plant to forecast the system behavior and optimize the current control move,thus producing the best future performance.Hence,models are core to every form of MPC.An MPC-based controller for path tracking is implemented using a lower-fidelity vehicle model to control a higher-fidelity vehicle model.The vehicle models include a bicycle model,an 8-DOF model,and a 14-DOF model,and the reference paths include a straight line and a circle.In the MPC-based controller,the model is linearized and discretized for state prediction;the tracking is conducted to obtain the heading angle and the lateral position of the vehicle center of mass in inertial coordinates.The output responses are discussed and compared between the developed vehicle dynamics models and the CarSim model with three different steering input signals.The simulation results exhibit good path-tracking performance of the proposed MPC-based controller for different complexity vehicle models,and the controller with high-fidelity model performs better than that with low-fidelity model during trajectory tracking.展开更多
As intelligent vehicles become increasingly computerized and networked,they gain more autonomous capabilities.However,they are also becoming more exposed to cyber-threats which are likely to be a more prominent concer...As intelligent vehicles become increasingly computerized and networked,they gain more autonomous capabilities.However,they are also becoming more exposed to cyber-threats which are likely to be a more prominent concern.This paper proposes a cyber-attack detection method for autonomous vehicles based on secure estimation of vehicle states,with an example application under attacks in the vehicle localization system.To investigate the effects of vehicle model and estimator on the attack detection performance,different nonlinear vehicle dynamic models and estimation approaches are employed.The deviation between the measurement from the onboard sensors and the state estimation is monitored in real time.With the designed vehicle state estimator and preset threshold,the cyber-attack detection algorithm is further developed for autonomous vehicles,whose performance is tested in simulations where the vehicle localization system is assumed to be compromised during a double lane change maneuver.The test results demonstrate the feasibility and effectiveness of the proposed cyber-attack algorithm.In addition,the results illustrate the impacts of vehicle nonlinear characteristics on the cyber-attack detection performance.Beyond this,the effects of different vehicle models on the attack detection performance,as well as the selection of suitable filtering approaches for the attack detection,are also discussed.展开更多
An investigation is undertaken of an integrated mechanical-electromagnetic coupling system consisting of a rigid vehicle with heave, roll, and pitch motions, four electromagnetic energy harvesters and four tires subje...An investigation is undertaken of an integrated mechanical-electromagnetic coupling system consisting of a rigid vehicle with heave, roll, and pitch motions, four electromagnetic energy harvesters and four tires subject to uneven road excitations in order to improve the passengers' riding comfort and harvest the lost engine energy due to uneven roads. Following the derived mathematical formulations and the proposed solution approaches, the numerical simulations of this interaction system subject to a continuous sinusoidal road excitation and a single ramp impact are completed. The simulation results are presented as the dynamic response curves in the forms of the frequency spectrum and the time history, which reveals the complex interaction characteristics of the system for vibration reductions and energy harvesting performance. It has addressed the coupling effects on the dynamic characteristics of the integrated system caused by: (1) the natural modes and frequencies of the vehicle; (2) the vehicle rolling and pitching motions; (3) different road excitations on four wheels; (4) the time delay of a road ramp to impact both the front and rear wheels, etc., which cannot be tackled by an often used quarter vehicle model. The guidelines for engineering applications are given. The developed coupling model and the revealed concept provide a means with analysis idea to investigate the details of four energy harvester motions for electromagnetic suspension designs in order to replace the current passive vehicle isolators and to harvest the lost engine energy. Potential further research directions are suggested for readers to consider in the future.展开更多
An eight wheel independently driving steering(8 WIDBS)electric vehicle is studied in this paper.The vehicle is equipped with eight in-wheel motors and a steer-by-wire system.A hierarchically coordinated vehicle dyna...An eight wheel independently driving steering(8 WIDBS)electric vehicle is studied in this paper.The vehicle is equipped with eight in-wheel motors and a steer-by-wire system.A hierarchically coordinated vehicle dynamic control(HCVDC)system,including a high-level vehicle motion controller,a control allocation,an inverse tire model and a lower-level slip/slip angle controller,is proposed for the over-actuated vehicle system.The high-level sliding mode vehicle motion controller is designed to produce desired total forces and yaw moment,distributed to longitudinal and lateral forces of each tire by an advanced control allocation method.And the slip controller is designed to use a sliding mode control method to follow the desired slip ratios by manipulating the corresponding in-wheel motor torques.Evaluation of the overall system is accomplished by sine maneuver simulation.Simulation results confirm that the proposed control system can coordinate among the redundant and constrained actuators to achieve the vehicle dynamic control task and improve the vehicle stability.展开更多
文摘Today,it is difficult to further improve the dynamic performance of rail vehicles with conventional passive suspension.Also,simplified vehicle respectively running gear layouts that significantly could reduce vehicle weights are difficult to realize with modern requirements on passenger vibration comfort and wheel and rail wear.Active suspension is a powerful technology that can improve the vehicle dynamic performance and make simplified vehicle concepts possible.The KTH Railway group has,together with external partners,investigated active suspensions both numerically and experimentally for 15 years.The paper provides a summary of the activities and the most important findings.One major project carried out in close collaboration with the vehicle manufacturer Bombardier and the Swedish Transport Administration was the Green Train project,where a 2-car EMU test bench was used to demonstrate different active technologies.In ongoing projects,a concept of single axle-single suspension running gear is developed with active suspension both for comfort improvement and reduced wheel wear in curves.The results from on-track tests in the Green Train project were so good that the technology is now implemented in commercial trains and the simulation results for the single-axle running gear are very promising.
基金supported by the National Natural Science Foundation of China(61403158,61520106008)the Project of the Education Department of Jilin Province(2016-429)
文摘Next-generation vehicle control and future autonomous driving require further advances in vehicle dynamic state estimation. This article provides a concise review, along with the perspectives, of the recent developments in the estimation of vehicle dynamic states. The definitions used in vehicle dynamic state estimation are first introduced, and alternative estimation structures are presented. Then, the sensor configuration schemes used to estimate vehicle velocity, sideslip angle, yaw rate and roll angle are presented. The vehicle models used for vehicle dynamic state estimation are further summarized, and representative estimation approaches are discussed. Future concerns and perspectives for vehicle dynamic state estimation are also discussed.
基金supported by National Natural Science Foundation of China (Grant No.50905092)
文摘The performance of the vehicle dynamics stability control system(DSC) is dominated by the accurate estimation of tire forces in real-time.The characteristics of tire forces are determined by tire dynamic states and parameters,which vary in an obviously large scope along with different working conditions.Currently,there have been many methods based on the nonlinear observer to estimate the tire force and dynamic parameters,but they were only used in off-line analysis because of the computation complexity and the dynamics differences of four tires in the steering maneuver conditions were not considered properly.This paper develops a novel algorithm to observe tire parameters in real-time controller for DSC.The algorithm is based on the sensor-fusion technology with the signals of DSC sensors,and the tire parameters are estimated during a set of maneuver courses.The calibrated tire parameters in the control cycle are treated as the elementary states for vehicle dynamics observation,in which the errors between the calculated and the measured vehicle dynamics are used as the correcting factors for the tire parameter observing process.The test process with a given acceleration following a straight line is used to validate the estimation method of the longitudinal stiffness;while the test process with a given steering angle is used to validate the estimated value of the cornering stiffness.The ground test result shows that the proposed algorithm can estimate the tire stiffness accurately with an acceptable computation cost for real-time controller only using DSC sensor signal.The proposed algorithm can be an efficient algorithm for estimating the tire dynamic parameters in vehicle dynamics stability control system,and can be used to improve the robustness of the DSC controller.
基金supported by National Natural Science Foundation of China(Grant No.50875112)PhD Programs Foundation of Ministry of Education of China(Grant No.20093227110013)+1 种基金Jiangsu Provincial Natural Science Foundation of China(Grant No.BK2010337)Natural Science Foundation of Higher Education of Jiangsu Province,China(Grant No.09KJA580001)
文摘The existing research of the integrated chassis control mainly focuses on the different evaluation indexes and control strategy. Among the different evaluation indexes, the comprehensive properties are usually not considered based on the non-linear superposition principle. But, the control strategy has some shortages on tyre model with side-slip angle, road adhesion coefficient, vertical load and velocity. In this paper, based on belief, desire and intention(BDI)-agent model framework, the TYRE agent, electric power steering(EPS) agent and active suspension system(ASS) agent are proposed. In the system(SYS) agent, the coordination mechanism is employed to manage interdependences and conflicts among other agents, so as to improve the flexibility, adaptability, and robustness of the global control system. Due to the existence of the simulation demand of dynamic performance, the vehicle multi-body dynamics model is established by SIMPACK. And then the co-simulation analysis is conducted to evaluate the proposed multi-agent system(MAS) controller. The simulation results demonstrate that the MAS has good effect on the performance of EPS and ASS. Meantime, the better road feeling for the driver is provided considering the multiple and complex driving traffic. Finally, the MAS rapid control prototyping is built to conduct the real vehicle test. The test results are consistent to the simulation results, which verifies the correctness of simulation. The proposed research ensures the driving safety, enhances the handling stability, and improves the ride comfort.
基金Sponsored by the National Natural Science Foundation of China (501222155)
文摘A 7 degree-of-freedom (DOF) 4 wheels vehicle dynamics model based on Matlab-Simulink is established,and 7 DOF vehicle dynamics equations in the form of nonlinear state-space standards are given.The characters of the electronic throttle and the active braking system have been analyzed.And the electronic throttle model and the active braking system model are built according to the test results respectively.Off-line simulation results indicate that the model is suitable for the vehicle adaptive cruise control system,and both of the electronic throttle and the active braking system work in a reasonable way.An adaptive cruise control (ACC) example illustrates that the model has a good performance in cruise and distance keeping.
基金Supported by National Natural Science Foundation of China(Grant Nos.51275557,51422505)
文摘The current research of direct yaw moment control(DYC) system focus on the design of target yaw moment and the distribution of wheel brake force. The differential braking intervention can effectively improve the lateral stability of the vehicle, however, the effect of DYC can be improved a step further by applying the control of vehicle longitudinal velocity. In this paper, the relationship between the vehicle longitudinal velocity and lateral stability is studied, and the simulation results show that a decrease of 5 km/h of longitudinal velocity at a particular situation can bring 100° increasing of stable steering upper limit. A critical stable velocity considering the effect of steering and yaw rate measurement is defined to evaluate the risk of losing steer-ability or stability. A novel velocity pre-control method is proposed by using a hierarchical pre-control logic and is integrated with the traditional DYC system. The control algorithm is verified through a hardware in-the-loop simulation system. Double lane change(DLC) test results on both high friction coefficient(μ) and low μ roads show that by using the pre-control method, the steering effort in DLC test can be reduced by 38% and 51% and the peak value of brake pressure control can be reduced by 20% and 12% respectively on high μ and low μ roads, the lateral stability is also improved. This research proposes a novel DYC system with lighter control effort and better control effect.
基金supported by the National Natural Science Foundations of China (Nos. 50823004 and 50821063)the "Eleventh Five-year Plan" National Science and Technology Support Plan(No. 2009BAG12A01-C09)
文摘Based on the aerodynamics and vehicle dynamics, the aerodynamic performances and vehicle dynamic characteristics of two high-speed trains passing each other on the ground, embankment and bridge are studied. Firstly, a train aerodynamic model and a vehicle dynamic model are established. Through the simulation of the two models, the pressure waves, aerodynamic forces, and vehicle dynamic responses are obtained. Then, the pressure waves and aero- dynamic forces on different foundations are compared. The results show that the variation trends of pressure wave and aerodynamic forces of trains passing each other on different foundations are almost similar. The peak-to-peak differ- ences in pressure wave and aerodynamic force are below 4% and 3% in three cases in open air. Besides, the differences of security indexes, including coefficient of derailment, wheel unloading rate, the wheelset lateral force, and the wheel- rail vertical force, are below 2% among the three cases; the differences of comfort indexes, including the lateral acceleration and the vertical acceleration, are also below 2%. It is concluded that the dynamic performances of trains pass- ing each other are influenced little by different foundations in open air.
文摘The need to find alternative urban mobility solutions for delivery and transport has led mobility companies to devote enormous resources for research-based solutions to increase vehicle safety. This paper documents a virtual approach to investigate the influences of different load states to the vehicle dynamic of light electric vehicle. A model basing on a three-dimensional </span><span style="font-family:""><span style="font-family:Verdana;">multibody system was used, which consists of five bodies. By applying methods of multibody modelling the generalized equations of motion were generated. To </span><span style="font-family:Verdana;">include the behavior within the contact point between road and vehicle a</span><span style="font-family:Verdana;"> simplified tire models was added. The implementation of the equations allowed a first validation of the model via simulations. In a final modeling step the simulation results were interpreted in respect of plausibility. Afterwards, the model was simulated numerically to investigate different load states of the vehicle, by applying constant steering stimuli and variable velocities. In sum, the investigated model approach is useful to identify safety relevant parameters and shows the effects of load states to the vehicle dynamics. Furthermore, it behaves plausibly regarding general vehicle dynamics. These results prove </span><span style="font-family:Verdana;">the general usability of the model for the development controllers and esti</span><span style="font-family:Verdana;">mators in driver assistances systems.
文摘A computer software named VDAS (Vehicle Dynamic Analysis Simulation) is presented.Based on the mathematical modelling for a military vehicle as a 3-D dynamic system, the softwarecreates random excitation resulting from double side road-surface roughness by statisticalsimulation, and solves for the time series of the system response from the system state equations,and gives out the results in probability statistics as well as performance evaluations.
文摘Rolling stock manufacturers are finding structural solutions to reduce power required by the vehicles,and the lightweight design of the car body represents a possible solution.Optimization processes and innovative materials can be combined in order to achieve this goal.In this framework,we propose the redesign and optimization process of the car body roof for a light rail vehicle,introducing a sandwich structure.Bonded joint was used as a fastening system.The project was carried out on a single car of a modern tram platform.This preliminary numerical work was developed in two main steps:redesign of the car body structure and optimization of the innovated system.Objective of the process was the mass reduction of the whole metallic structure,while the constraint condition was imposed on the first frequency of vibration of the system.The effect of introducing a sandwich panel within the roof assembly was evaluated,focusing on the mechanical and dynamic performances of the whole car body.A mass saving of 63%on the optimized components was achieved,corresponding to a 7.6%if compared to the complete car body shell.In addition,a positive increasing of 17.7%on the first frequency of vibration was observed.Encouraging results have been achieved in terms of weight reduction and mechanical behaviour of the innovated car body.
基金supported by the Imperial College Research Fellowship(ICRF 2022-2026)。
文摘Active suspension systems(ASSs)have been proposed and developed for a few decades,and have now once again become a thriving topic in both academia and industry,due to the high demand for driving comfort and safety and the compatibility of ASSs with vehicle electrification and autonomy.Existing review papers on ASSs mainly cover dynamics modeling and robust control;however,the gap between academic research outcomes and industrial application requirements has not yet been bridged,hindering most ASS research knowledge from being transferred to vehicle companies.This paper comprehensively reviews advances in ASSs for road vehicles,with a focus on hardware structures and control strategies.In particular,state-of-the-art ASSs that have been recently adopted in production cars are discussed in detail,including the representative solutions of Mercedes active body control(ABC)and Audi predictive active suspension;novel concepts that could become alternative candidates are also introduced,including series active variable geometry suspension,and the active wheel-alignment system.ASSs with compact structure,small mass increment,low power consumption,high-frequency response,acceptable economic costs,and high reliability are more likely to be adopted by car manufacturers.In terms of control strategies,the development of future ASSs aims not only to stabilize the chassis attitude and attenuate the chassis vibration,but also to enable ASSs to cooperate with other modules(e.g.,steering and braking)and sensors(e.g.,cameras)within a car,and even with high-level decision-making(e.g.,reference driving speed)in the overall transportation system-strategies that will be compatible with the rapidly developing electric and autonomous vehicles.
基金Supported by National Natural Science Foundation of China(Grant No.52272387)State Key Laboratory of Mechanical Behavior and System Safety of Traffic Engineering Structures,Shijiazhuang Tiedao University of China(Grant No.KF2020-29)Beijing Municipal Science and Technology Commission through Beijing Nova Program of China(Grant No.20230484475).
文摘This paper presents an integrated control scheme for enhancing the ride comfort and handling performance of a four-wheel-independent-drive electric vehicle through the coordination of active suspension system(ASS)and anti-lock braking system(ABS).First,a longitudinal-vertical coupled vehicle dynamics model is established by integrating a road input model.Then the coupling mechanisms between longitudinal and vertical vehicle dynamics are analyzed.An ASS-ABS integrated control system is proposed,utilizing an H∞controller for ASS to optimize load transfer effect and a neural network sliding mode control for ABS implementation.Finally,the effectiveness of the proposed control scheme is evaluated through comprehensive tests conducted on a hardware-in-loop(HIL)test platform.The HIL test results demonstrate that the proposed control scheme can significantly improve the braking performance and ride comfort compared to conventional ABS control methods.
文摘Pneumatic tire modeling and validation have been the topic of several research papers, however, most of these papers only deal with pneumatic passenger and truck tires. In recent years, wheeled-scaled vehicles have gained lots of attention as a feasible testing platform, nonetheless up to the authors’ knowledge there has been no research regarding the use of scaled tires and their effect on the overall vehicle performance characteristics. This paper presents a novel scaled electric combat vehicle tire model and validation technique. The pro-line lockdown tire size 3.00 × 7.35 is modeled using the Finite Element Analysis (FEA) technique and several materials including layered membrane, beam elements, and Mooney-Rivlin for rubber. The tire-rim assembly is then described, and the rigid body analysis is presented. The tire is then validated using an in-house custom-made static tire testing machine. The tire test rig is made specifically to test the pro-line tire model and is designed and manufactured in the laboratory. The tire is validated using vertical stiffness and footprint tests in the static domain at different operating conditions including several vertical loads. Then the tire is used to perform rolling resistance and steering analysis including the rolling resistance coefficient and the cornering stiffness. The analysis is performed at different operating conditions including longitudinal speeds of 5, 10, and 15 km/h. This tire model will be further used to determine the tractive and braking performance of the tire. Furthermore, the tire test rig will also be modified to perform cornering stiffness tests.
基金This work was partly funded by the National Key R&D Project of China(2021YFB3400704)China State Railway Group(K2022J004 and N2023J011)China Railway Chengdu Group(CJ23018).
文摘Purpose–The safety and reliability of high-speed trains rely on the structural integrity of their components and the dynamic performance of the entire vehicle system.This paper aims to define and substantiate the assessment of the structural integrity and dynamical integrity of high-speed trains in both theory and practice.The key principles and approacheswill be proposed,and their applications to high-speed trains in Chinawill be presented.Design/methodology/approach–First,the structural integrity and dynamical integrity of high-speed trains are defined,and their relationship is introduced.Then,the principles for assessing the structural integrity of structural and dynamical components are presented and practical examples of gearboxes and dampers are provided.Finally,the principles and approaches for assessing the dynamical integrity of highspeed trains are presented and a novel operational assessment method is further presented.Findings–Vehicle system dynamics is the core of the proposed framework that provides the loads and vibrations on train components and the dynamic performance of the entire vehicle system.For assessing the structural integrity of structural components,an open-loop analysis considering both normal and abnormal vehicle conditions is needed.For assessing the structural integrity of dynamical components,a closed-loop analysis involving the influence of wear and degradation on vehicle system dynamics is needed.The analysis of vehicle system dynamics should follow the principles of complete objects,conditions and indices.Numerical,experimental and operational approaches should be combined to achieve effective assessments.Originality/value–The practical applications demonstrate that assessing the structural integrity and dynamical integrity of high-speed trains can support better control of critical defects,better lifespan management of train components and better maintenance decision-making for high-speed trains.
基金Science and Technology Development Project Agreement/Contract,China National Railway Group Co.,Ltd.(N2023J012)support by China Academy of Railway Sciences Corporation Limited(2021YJ208).
文摘Purpose–This paper aims to obtain the evolution law of dynamic performance of CR400BF electric multiple unit(EMU).Design/methodology/approach–Using the dynamic simulation based on field test,stiffness of rotary arm nodes and damping coefficient of anti-hunting dampers were tested.Stiffness,damping coefficient,friction coefficient,track gauge were taken as random variables,the stochastic dynamics simulation method was constructed and applied to research the evolution law with running mileage of dynamic index of CR400BF EMU.Findings–The results showed that stiffness and damping coefficient subjected to normal distribution,the mean and variance were computed and the evolution law of stiffness and damping coefficient with running mileage was obtained.Originality/value–Firstly,based on the field test we found that stiffness of rotary arm nodes and damping coefficient of anti-hunting dampers subjected to normal distribution,and the evolution law of stiffness and damping coefficient with running mileage was proposed.Secondly stiffness,damping coefficient,friction coefficient,track gauge were taken as random variables,the stochastic dynamics simulation method was constructed and applied to the research to the evolution law with running mileage of dynamic index of CR400BF EMU.
基金The project supported by the National Natural Science Foundation of China(59935100)the Foundation of Ph.D Student Education of China(20020613001)the Foundation of the Author of National Excellent Doctoral Dissertation of China(2000048,2002048)
文摘The effect of rail corrugation on the vertical dynamics of railway vehicle coupled with a curved track is investigated in detail with a numerical method when a wheelset is steadily curving. In the calculation of rail corrugation we consider the combination of Kalkers rolling contact theory modified, a model of material loss on rail running surface, and a dynamics model of railway vehicle coupled with a curved track. In the establishment of the dynamic model, for simplicity, one fourth of the freight car without lateral motions, namely a wheelset and the equivalent one fourth freight car body above it, is considered. The Euler beam is used to model the rails and the track structure under the rails is replaced with equivalent springs, dampers and mass bodies. The numerical results show the great influence of the rail corrugation on the vibration of the parts of the vehicle and the track, and the some characters of rail corrugation in development.
基金This paper is funded by International Graduate Exchange Program of Beijing Institute of Technology。
文摘Model predictive control(MPC)algorithm is established based on a mathematical model of a plant to forecast the system behavior and optimize the current control move,thus producing the best future performance.Hence,models are core to every form of MPC.An MPC-based controller for path tracking is implemented using a lower-fidelity vehicle model to control a higher-fidelity vehicle model.The vehicle models include a bicycle model,an 8-DOF model,and a 14-DOF model,and the reference paths include a straight line and a circle.In the MPC-based controller,the model is linearized and discretized for state prediction;the tracking is conducted to obtain the heading angle and the lateral position of the vehicle center of mass in inertial coordinates.The output responses are discussed and compared between the developed vehicle dynamics models and the CarSim model with three different steering input signals.The simulation results exhibit good path-tracking performance of the proposed MPC-based controller for different complexity vehicle models,and the controller with high-fidelity model performs better than that with low-fidelity model during trajectory tracking.
基金Funding was provided by State Key Laboratory of Automotive Safety and Energy(Grant No.KF2021)SUG-NAP Grant of Nanyang Technological University,Singapore(Grant No.M4082268.050).
文摘As intelligent vehicles become increasingly computerized and networked,they gain more autonomous capabilities.However,they are also becoming more exposed to cyber-threats which are likely to be a more prominent concern.This paper proposes a cyber-attack detection method for autonomous vehicles based on secure estimation of vehicle states,with an example application under attacks in the vehicle localization system.To investigate the effects of vehicle model and estimator on the attack detection performance,different nonlinear vehicle dynamic models and estimation approaches are employed.The deviation between the measurement from the onboard sensors and the state estimation is monitored in real time.With the designed vehicle state estimator and preset threshold,the cyber-attack detection algorithm is further developed for autonomous vehicles,whose performance is tested in simulations where the vehicle localization system is assumed to be compromised during a double lane change maneuver.The test results demonstrate the feasibility and effectiveness of the proposed cyber-attack algorithm.In addition,the results illustrate the impacts of vehicle nonlinear characteristics on the cyber-attack detection performance.Beyond this,the effects of different vehicle models on the attack detection performance,as well as the selection of suitable filtering approaches for the attack detection,are also discussed.
基金supporting S. Zhou to visit University of Southampton for one year to engage in this researchHarbin Engineering University for supporting J. T. Xing to visit Harbin Engineering University (Grant HEUCF160104)
文摘An investigation is undertaken of an integrated mechanical-electromagnetic coupling system consisting of a rigid vehicle with heave, roll, and pitch motions, four electromagnetic energy harvesters and four tires subject to uneven road excitations in order to improve the passengers' riding comfort and harvest the lost engine energy due to uneven roads. Following the derived mathematical formulations and the proposed solution approaches, the numerical simulations of this interaction system subject to a continuous sinusoidal road excitation and a single ramp impact are completed. The simulation results are presented as the dynamic response curves in the forms of the frequency spectrum and the time history, which reveals the complex interaction characteristics of the system for vibration reductions and energy harvesting performance. It has addressed the coupling effects on the dynamic characteristics of the integrated system caused by: (1) the natural modes and frequencies of the vehicle; (2) the vehicle rolling and pitching motions; (3) different road excitations on four wheels; (4) the time delay of a road ramp to impact both the front and rear wheels, etc., which cannot be tackled by an often used quarter vehicle model. The guidelines for engineering applications are given. The developed coupling model and the revealed concept provide a means with analysis idea to investigate the details of four energy harvester motions for electromagnetic suspension designs in order to replace the current passive vehicle isolators and to harvest the lost engine energy. Potential further research directions are suggested for readers to consider in the future.
基金Supported by the Ministerial Level Advance Research Foundation(40402050168)
文摘An eight wheel independently driving steering(8 WIDBS)electric vehicle is studied in this paper.The vehicle is equipped with eight in-wheel motors and a steer-by-wire system.A hierarchically coordinated vehicle dynamic control(HCVDC)system,including a high-level vehicle motion controller,a control allocation,an inverse tire model and a lower-level slip/slip angle controller,is proposed for the over-actuated vehicle system.The high-level sliding mode vehicle motion controller is designed to produce desired total forces and yaw moment,distributed to longitudinal and lateral forces of each tire by an advanced control allocation method.And the slip controller is designed to use a sliding mode control method to follow the desired slip ratios by manipulating the corresponding in-wheel motor torques.Evaluation of the overall system is accomplished by sine maneuver simulation.Simulation results confirm that the proposed control system can coordinate among the redundant and constrained actuators to achieve the vehicle dynamic control task and improve the vehicle stability.