MECHANICAL-ELECTRIC COUPLING DYNAMICAL CHARACTERISTICS OF AN ULTRA-HIGH SPEED GRINDING MOTORIZED SPINDLE SYSTEM

On the basis of the traditional mechanical model of a grinding wheel rotor and the mechanical-electric coupling model with ideal sinusoidal supply, taking high-frequency converting current of inverter power switches into further consideration, a modified mechanical-electric coupling model is created. The created model consists of an inverter, a motorized spindle, a grinding wheel and grinding loads. Some typical non-stationary processes of the grinding system with two different supplies, including the starting, the speed rising and the break in grinding loads, are compared by making use of the created model. One supply is an ideal sinusoidal voltage source, the other is an inverter. The theoretical analysis of the high-order harmonic is also compared with the experimental result. The material strategy of suppressing high-order harmonic mechanical-electric coupling vibration by optimizing inverter operating parameters is proposed.

Experimental Investigation on Vortex-Induced Vibration of Steel Catenary Riser

Steel catenary riser（SCR） is the transmission device between the seabed and the floating production facilities. As developments move into deeper water, the fatigue life of the riser can become critical to the whole production system, especially due to the vortex-induced vibration（VIV）, which is the key factor to operational longevity. As a result, experimental investigation about VIV of the riser was performed in a large plane pool which is 60 m long, 36 m wide and 6.5 m deep. Experiments were developed to study the influence of current speed and seabed on VIV of SCR. The results show that amplitudes of strain and response frequencies increase with the current speed both in cross-flow（CF） and in-line（IL）. When the current speed is high, multi-mode response is observed in the VIV motion. The amplitudes of strain in IL direction are not much smaller than those in CF direction. The seabed has influence on the response frequencies of riser and the positions of damage for riser.

The steady and vibrating statuses of tulip tree leaves in wind

The study of tree leaf aerodynamics is useful to tree protection, solar panel design and development of new power generation technology. 73 tulip leaves were tested in suspended condition and with front as well as back surface of the lamina facing wind. Three types of vibrating statuses, two types of steady statuses, and five critical wind speeds were observed. The existence probabilities of the statuses and criticals, the probability density distribution of every critical over the range of wind speed 0-27 m/s, and the expected values of the criticals were obtained by statistics. The critical Reynolds number, defined by critical wind speed and lamina length, shows an increasing trend with increasing the lamina area or length to width ratio of the lamina, but it shows no trend of increase or decrease with increasing the length ratio of petiole to lamina.

Assessment of Ballast Flying in the National Railway Network of Ethiopia

One of the major problems in ballasted railroads is ballast flying, which is the projection of ballast particles from the at-rest position as the train passes over the track of a railway structure, mainly due to high speed. In this research, the possibility of railway ballast flying for the double track Addis-Adama section of the new Addis-Djibouti railway line is assessed by determining the major causes of ballast flying and applying Discrete Element Modeling (DEM) with the aid of Particle Flow Code (PFC3D) software. The analysis comprised of an impact load and ballast material behavior which were used to determine the vibrational speed of individual ballast particles. The governing result from the series of discrete element analyses performed by considering fouled ballast gradation with grain-size diameter of 22.4 mm gives rise to a ballast maximum vibrational speed of 0.014 m/s. Since the ballast vibrational speed for Addis Ababa-Adama line is less than 0.02 m/s that is recommended by the literature, no ballast flight is expected under the present traffic and ballast conditions.

Numerical study on influence of structural vibration on cavitating flow around axisymmetric slender body

The unsteady behaviors of cloud cavitating flow would lead to structural vibration and deformation that conversely affect its development. The present paper aims to preliminarily discuss the influences of structural vibration on the development of the cavitating flow. Simulations of a slender body are carried out under different vibration amplitudes and frequencies. The results show that the structural vibration causes alternate variation of local attack angle at the head of the body, and thus changes the development of cavitation and re-entrant jet. On the downstream side, the length and thickness of the cavity are larger than that on the upstream side due to larger area of negative pressure. For a large vibration amplitude, alternate variations of the local attack angle change the adverse pressure gradient at the closure of the cavity, and then affect the development of the re-entrant jet, so that the phenomena of local shedding of the cavitation happen, compared with global shedding in the case of no structural vibration. For a frequency larger than 0.05, transverse speed of the vibration is suggested to be a dominant factor in controlling the behavior of the cavitating flow besides the local attack angle, since it causes local cavitating phenomena.