DESIGN AND PROPERTIES OF A FUNCTIONALLY GRADIENT CERAMIC TOOL MATERIAL

Based on the analyses of the severity of cutting process as well as the failure mechanisms of ceramic tools, a model for designing functionally gradient ceramic tool materials with symmetrical distribution is presented, by which a Al 2O 3/(W,Ti)C ceramic tool material FG 2 was developed. Multi objective optimization method was employed in designing the compositional distribution of this ceramic tool material. The results of both continuous and intermittent cutting tests are indicative of the much better cutting behavior of the functionally gradient ceramic tool FG 2 than that of the common ceramic tool SG 4.

Effects of the Component and Fiber Gradient Distributions on the Strength of Cement-based Composite Materials

The effects of the component gradient distribution at interface and the fiber gradient distribution on the strength of cement-based materials were studied. The results show that the flexural strength and compressive strength of the mortar and concrete with interface component and fiber gradient distributions are obviously improved. The strengthes of the fiber gradient distributed mortar and concrete (FGDM/C) are higher than those of fiber homogeneously distributed mortar and concrete (FHDM/C). To obtain the same strength, therefore, a smaller fiber volume content in FGDM/C is needed than that in FHDM/C. The results also show that the component gradient distribution of the concrete can be obtained by means of multi-layer vibrating formation.

NVESTIGATION OF PRODUCTOPN OF FUNCTIONALLY GRADIENT MATERIAL BY ELECTROLESS PLATING

Thispaper proposed a new methodof producing Ceramic/ Metalfunctionally gradient mate rialby electroless platingtechnique. The experimentof producing SiC/ Ni PFGM wascar ried out with self made electroless plating facilities. The results show that the thickness of FGMcoating andthegradientdistribution ofcompositioncanbecontrolled byoptimizingelec trolessplating technology and changing the parameters such as plating time, the additionspeed and concentration of SiCparticles. Analysisdemonstratesthatthereisastrongrelation ship amongthe SiCcontent,the microstructureandthe mechanicalproperty ofthe FGM.

Preparation and Arc Breakdown Behavior of Nanocrystalline W-Cu Electrical Contact Materials

Nanostructured （NS） W-Cu composite powder was prepared by mechanical alloying （MA）, and nanostructured bulk of W-Cu contact material was fabricated by hot pressed sintering in an electrical vacuum furnace. The microstructure, electric conductivity, hardness, breakdown voltage and arcing time of NS W-Cu alloys were measured and compared to conventional W-Cu alloys prepared by powder metallurgy. The results show that microstructural refinement and uniformity can improve the breakdown behavior, the electric arc stability and the arc extinction ability of nanostructured W-Cu contacts materials. Also, the nanostructured W-Cu contact material shows the characteristic of spreading electric arcs, which is of benefit to electric arc erosion.

Preparation of 2024/3003 gradient materials by semi-continuous casting using double-stream-pouring technique

The 2024/3003 aluminum gradient alloys are prepared by semi continuous casting. The influences of throttle bore diameter of embedded nozzle and temperature of internal melt on composition distribution, macrostructure, hardness are analyzed, and the stability of gradient distribution of composition, macrostructure and hardness along the axial direction of the ingot is also studied. The results show that diffe rent composition profiles can be achieved by adjusting the processing parameters; the volume fraction of inner alloy in the ingot can be increased by enlarging the throttle bore diameter and elevating the temperature of inner melt; quasi steady solidification can be realized within 20 s during cast processing, and consistent quality ingot is obtained by controlling the casting speed and liquid height of inner melt.

Arc erosion behavior of a nanocomposite W-Cu electrical contact material

The erosion behavior of a nanocomposite W-Cu material under arc breakdown was investigated. The arc erosion rates of the material were determined, and the eroded surfaces and arc erosion mechanisms were studied by scanning eleclion microscopy. It is concluded that the nanocomposite W-Cu electrical contact material shows a characteristic of spreading arcs. The arc breakdown of a commercially used W-Cu alloy was limited in a few areas, and its average arc erosion rate is twice as large as that of the former. Furthermore, it is also proved that the arc extinction ability and arc stability of the nanocomposite W-Cu material are excellent, and melting is the major failure modality in the make-and-break operation of arcs.

Microstructure and mechanical properties of additive manufactured steel-Al structure materials with nickel gradient layers

The microstructure and mechanical properties of steel/Al structure material produced by additive manufacturing （AM） was investigated in this work based on the cold metal transfer welding. The results show that the microstructure gradually changed from the steel side to the aluminum side. The microstructure in the steel layer consisted of vermiform like ferrite and anstenite structure, while in the aluminum layer the microstructure was constituted by c^-A1 grains and typical reticulate distributive Al-Si eutectic structure. Besides, a 7 y.m thickness Ni-Al intermetallic compound layer was emerged at the interface of nickel and aluminum layer. The maximum room-temperature tensile strength of the Steel-Al structure materials was found to be 54 MPa, the rupture morphology showed a brittle fracture characteristic.

Crack tip field in functionally gradient material with exponential variation of elastic constants in two directions

This paper presents an exact solution of the crack tip field in functionally gradient material with exponential variation of elastic constants. The dimensionless Poisson＇s ratios v0 of the engineering materials （iron, glass …… ） are far less than one; therefore, neglecting them, one can simplify the basic equation and the exact solution is easy to obtain. Although the exact solution for the case v0 ≠ 0 is also obtained, it is very complicated and the main result is the same with the case v0 = 0 （it will be dealt with in Appendix VII）. It has been found that the exponential term exp（ax ＋ by） in the constitutive equations becomes exp（ ax /2 ＋ by/2- kr /2 ） in the exact solution.

AN IN SITU SURFACE COMPOSITE AND GRADIENT MATERIAL OF Al-Si ALLOY PRODUCED BY ELECTROMAGNETIC FORCE

Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force applied by the metal melt exerts on the pri mary phase when the movement of the melt in the direction of electromagnetic force is limited. As a result, the repulsive force exerts on the primary phase to push them to move in the direction opposite to that of the electromagnetic force when the metal melt with primary phase solidifies under an electromagnetic force field. Based on this, a new method for production of in situ surface composite and gradient material by electromagnetic force is proposed. An in situ primary Si reinforced surface composite of Al-15wt%Si alloy and gradient material of Al-l9wt%Si alloy were produced by this method. The microhardness of the primary Si is HV1320. The reinforced phase size is in the range from 40μm to 100μm. The wear resistance of Al-Si alloy gradient material can be more greatly increased than that of their matrix material.

ANTI-PLANE SHEAR CRACK IN A FUNCTIONALLY GRADIENT PIEZOELECTRIC MATERIAL

The main objective of this paper is to study the singular natureof the crack-tip stress and electric displacement field in afunctionally gradient piezoelectric medium having materialcoefficients with a discontinuous derivative. The problem isconsidered for the simplest possible loading and geometry, namely,the anti-plane shear stress and electric displacement in -plane oftwo bonded half spaces in which the crack is parallel to theinterface.

Electrical, Thermal, and Mechanical Properties of Cu/Ti3AlC2 Functional Gradient Materials Prepared by Low-temperature Spark Plasma Sintering

Cu/Ti3AlC2 composite and functional-gradient materials with excellent electrical conductivity and thermal conductivity as well as good flexural properties were prepared by low-temperature spark plasma sintering of Cu and Ti3AlC2 powder mixtures. The phase compositions of the materials were analyzed by X-ray diffraction, and their microstructure was characterized by scanning electron microscopy and energy dispersive X-ray spectroscopy. Further, the electrical conductivity, thermal conductivity, and flexural properties of the materials were tested. Results show that, for the composite materials, the resistivity rises from 0.75 × 10^-7 Ω·m only to 1.32 × 10^-7 Ω·m and the thermal diffusivity reduces from 82.5 mm^2/s simply to 39.8 mm^2/s, while the flexural strength improves from 412.9 MPa to 471.3 MPa, as the content of Ti3AlC2 is increased from 5 wt%to 25 wt%. Additionally, the functional-gradient materials sintered without interface between the layers exhibit good designability, and their overall electrical conductivity, thermal conductivity, and flexural strength are all higher than those of the corresponding uniform composite material.

Cycling performance of layered oxide cathode materials for sodium-ion batteries

Layered oxide is a promising cathode material for sodium-ion batteries because of its high-capacity,high operating voltage,and simple synthesis.Cycling performance is an important criterion for evaluating the application prospects of batteries.However,facing challenges,including phase transitions,ambient stability,side reactions,and irreversible anionic oxygen activity,the cycling performance of layered oxide cathode materials still cannot meet the application requirements.Therefore,this review proposes several strategies to address these challenges.First,bulk doping is introduced from three aspects:cationic single doping,anionic single doping,and multi-ion doping.Second,homogeneous surface coating and concentration gradient modification are reviewed.In addition,methods such as mixed structure design,particle engineering,high-entropy material construction,and integrated modification are proposed.Finally,a summary and outlook provide a new horizon for developing and modifying layered oxide cathode materials.

AN ASYMPTOTIC METHOD FOR ANALYZING THE STRESS IN A FUNCTIONALLY GRADIENT MATERIAL LAYER ON A SURFACE OF A STRUCTURAL COMPONENT

A simple and effective method for analyzing the stress distribution in a Functionally Gradient Material(FGM) layer on the su;face of a structural component is proposed in this paper. Generally, the FGM layer is very thin compared with the characteristic length of the structural component, and the nonhomogeneity exists only in the thin layer. Based on these features, by choosing a small parameter I which characterizes the stiffness of the layer relative to the component, and expanding the stresses and displacements on the two sides of the interface according to the parameter lambda, then asymptotically using the continuity conditions of the stresses and displacements on the interface, a decoupling computing process of the coupling control equations of the layer and the structural component is realized. Finally, two examples are given to illustrate the application of the method proposed.

Genetic Algorithm for the Thermal Stresses Optimum Design ofFunctionally Gradient Material Plate

Based on the thermal stress distribution for functionally gradient material (FGM) plates, a Genetic Algorithm (GA) method for the thermal stresses optimum design of FGM plate with computer technologies is given. The minimum thermal stresses combination distribution for FGM is obtained.

ELASTOPLASTIC OPTIMUM DESIGN OF Ni/TiC FUNCTIONAL GRADIENT MATERIAL

The thermal residual stresses developed in a disk-shaped, Ni/TiC functionally gradient material (FGM) during its fabrication are investigated by an elastic-plastic finite element numerical ap-proach. Constitutive relations for the graded Ni-TiC composite inter-layers between pure metal Ni and ceramic TiC are estimated by using an effectiv-medium approach, and effective plastic strain and stress distributions are computed for simulated cooling from an assumed fab-rication temperature. Analyses are performed for a fixed specimen ge-ometry and the graded region is treated as a series of perfectly bonded equal-thick layers. The results are compared with those obtained by on-ly considering elastic material response to assess the effect of plasticity on the optimum fabrication design of the Ni/TiC FGM. It is demon-strated that the consideration of plasticity is of critical importance for optimization of the metal/ceramic gradient materials.

Ti/Al_2O_3 Functionally Gradient Material Prepared by the Explosive Compaction/SHS Process

Ti1Al2O3 Functionally Gradient Material (FGM) was prepared by an explosive compaction/SHS process. Ten sheets of the compounding powder were laminated and pressed to get a green body of FGM. It was then compacted explosively By burying the explosive compaction body into a stoichiometric Al/TiO2 mixture and igniting the combustion of the stoichiometric Al/TiO2 mixture, the SHS reaction of the explosive compaction body was initiated by the heat released from the combustion of the stoichiometric Al/TiO2 mixture. In this way, Ti/Al2O3 FGM was synthesized. The adiabatic temperatures of each gradient layer were calculated when the preheating temperatures were 298 K and 1173 K, respectively The microstructure, composition and properties of Ti/Al2O3 FGM and the reaction mechanism of each gradient layer were studied. It was found that Ti/Al2O3 FGM prepared by the explosive compaction/SHS process had a high density and a high microhardness. Its structure, composition and properties showed apparent gradient distribution. The structure of the standard stoichiometric ratio gradient layer of FGM was a network structure. Its reaction mode could be described as follows: Al powder melted first, then the molten Al penetrated into the TiO2 zone and reacted with TiO2, and big pores were left in the original positions of Al powder. The reaction of gradient layers with the addition of Al3O3 as diluents was similar to that of the standard stoichiometric ratio gradient layer, so were their structure and composition. However, the reaction of gradient layers with the addition of Ti as diluents was more complex and the composition deviated slightly from the designed one

Microstructure and Mechanical Properties of ZrO_2-Ni Functionally Gradient Material

The fabrication. microstructure and mechanical properties of ZrO2-Ni functionally gradient materials (FGM ) have been studied. FGM as well as non-FG M of ZrO2-Ni system was developed by powder metallurgical process. X-ray diffractometer (XRD ). electron probe microanalyzer (EPMA), scanning electron microscope (SEM ) and optical microscope were employed to investigate the crystalline phases. chemical composition and microstructure Experimental results demonstrate that the composition and microstructure of ZrO2-Ni FGM have the expected gradient distribution. There are no distinct interfaces in the FGM due to the gradient change of components. that is, the constituents are continuous in microstructure everywhere. Moreover, Vickers hardness and flexural strength were measured for the common composites as a function of composition. It is made clear that the mechanical properties of the FGM vary corresponding to the constitutional changes as well

Synthesis,characterization and biological activity in vitro of FeCrAl(f)/HA asymmetrical biological functionally gradient materials

FeCrAl(f)/HA biological functionally gradient materials(FGMs) were successfully fabricated by the hot pressing technique.Scanning electron microscope(SEM),energy dispersive spectrometer(EDS) and bending strength test machine were utilized to characterize the microstructure,component,mechanical properties and the formation of the Ca-deficient apatite on the surface of these materials.The results indicate that an asymmetrical FeCrAl(f)/HA FGM,consolidating powders prepared by mixing HA with 3%–15%(volume fraction) is successfully prepared.Both of the matrix and FeCrAl fiber are integrated very tightly and bite into each other very deeply.And counter diffusion takes place to some extent in two phase interfaces.The elemental compositions of the FeCrAl(f)/HA FGM change progressively.Ca and P contents increase gradually with immersion time increasing,and thereafter approach equilibrium.The bone-like apatite layer forms on the materials surface,which possesses benign bioactivity,and the favorable biocompatibility can provide potential firm fixation between FeCrAl(f)/HA asymmetrical FGM implants and human bone.

Higher order asymptotic fields for mode Ⅰ crack in functionally gradient material

Higher order stress fields for a mode Ⅰ crack perpendicular to the direction of property variation in a functionally gradient material(FGM), which has an exponential variation of elastic modulus along the gradient direction, were obtained through an asymptotic analysis. The Poisson’s ratio of the FGMs was assumed to be constant throughout the analysis. The first five terms in the asymptotic expansions of crack tip stress fields were derived to bring out the influence of nonhomogeneity on the structure of the stress field explicitly. The analysis reveals that only the higher order terms in the expansion are influenced by the material nonhomogeneity. Moreover, it can be seen from expressions of higher order stress fields that at least three terms must be considered in the case of FGMs in order to explicitly account for the nonhomogeneity effects on the structure of crack tip stress fields.