Three kinds of amphiphilic PMADAB gels were prepared through radiation-induced polymerization and crosslinking of methacryloxyethyl dimethylalkane ammonium bromide(MADAB) with different alkyl side chains(butyl,octyl a...Three kinds of amphiphilic PMADAB gels were prepared through radiation-induced polymerization and crosslinking of methacryloxyethyl dimethylalkane ammonium bromide(MADAB) with different alkyl side chains(butyl,octyl and dodecyl).The length of alkyl side chains had significant influence on swelling behavior of the PMADAB gels in alcohol/water solvent.Equilibrium swelling degree(EDS) of PMBDAB(butyl) gel in water was ca.160 and decreased with increasing alcohol content(x),whereas EDS of PMODAB(octyl)and PMDDDAB(dodecyl) gels showed a convex-upward function of x,i.e.,these two gels barely swelled in pure water and swelled with increasing x and then shrank gradually.This phenomenon was explained by the hydrophobic association of long alkyl chains and a cosolvency effect of PMADAB in alcohol and water.The swelling behavior of PMADAB gels in methanol,ethanol and isopropanol were similar,and their EDS are related with the dielectric constant of alcohol solvents.The results suggest that PMADAB gels may be potential absorbents for various kinds of alcohols.展开更多
The formamide-titanium oxide interaction mechanism is a research target of great importance for understanding the elementary events of the origin of life: the synthesis of nucleoside bases and formation of biological ...The formamide-titanium oxide interaction mechanism is a research target of great importance for understanding the elementary events of the origin of life: the synthesis of nucleoside bases and formation of biological molecules needed for life. Titanium oxide (TiO2) can act as a strongly adsorbing surface or a catalytic material. In the present study, a comparative molecular dynamics analysis performed to clarify the adsorbing and diffusion properties of liquid formamide on a TiO2 surface in the presence of water molecules. The structural features of the formamide concentration effect (the accumulation of molecules) on a TiO2 surface in the presence and absence of water solvent are cleared up. Modification of the formamide diffusion abilities mediated by a water solvent is observed to correlate with the formamide-water concentration distribution on the surface.展开更多
Achieving high energy density and fast charging of lithium-ion batteries can accelerate the promotion of electric vehicles.However,the increased mass loading causes poor charge transfer,impedes the electrochemical rea...Achieving high energy density and fast charging of lithium-ion batteries can accelerate the promotion of electric vehicles.However,the increased mass loading causes poor charge transfer,impedes the electrochemical reaction kinetics,and limits the battery charging rate.Herein,this work demonstrated a novel pattern integrated stamping process for creating channels in the electrode,which benefits ion transport and increases the rate performance of the electrode.Meanwhile,the pressure applied during the stamping process improved the contact between electrode and current collector and also enhanced the mechanical stability of the electrode.Compared to the conventional bar-coated electrode with the same thickness of 155μm(delivered a discharge capacity of 16 mAh g^(−1) at the rate of 3 C),the stamped low-tortuosity LiFePO_(4) electrode delivered 101 mAh g^(−1) capacity.Additionally,water was employed as a solvent in this study.Owing to its eco-friendliness,high scalability,and minimal waste generation,this novel stamping technique inspire a new method for the industrial-level efficient roll to roll fabrication of fast-charge electrodes.展开更多
The solvent debinding of water soluble binder in powder injection moulding (MIM) was investigated systematically, including the effects of solvent types, temperature and the thickness of green parts on the solvent deb...The solvent debinding of water soluble binder in powder injection moulding (MIM) was investigated systematically, including the effects of solvent types, temperature and the thickness of green parts on the solvent debinding rate. After studying the debinding of a green part with a thickness of 4.26 mm, it was found that, the debinding rate of polyethylene glycol(PEG) in water and alcohol was high initially, and then decreased; however, it would increase with temperature increasing. At room temperature, the dissolution rate of PEG in water was higher than that in alcohol, but the latter would be much faster with temperature increasing because the debinding activation energy in alcohol was 51.44 kJ·mol -1 ·K -1 , much higher than 24.23 kJ·mol -1 ·K -1 in water. With a green part thickness larger than 4.26 mm, the debinding was controlled by diffusion; but with that smaller than 2.36 mm, the debinding was controlled by both dissolution and diffusion.展开更多
Aqueous phase layer around bubble and water droplet are two additional processes in solvent sublation. In the dynamic process of mass transfer, they are always neglected, but they are very important in the investigati...Aqueous phase layer around bubble and water droplet are two additional processes in solvent sublation. In the dynamic process of mass transfer, they are always neglected, but they are very important in the investigation of thermodynamic equilibrium. In this paper, the effect of water droplet in solvent sublation was discussed in detail, and the previous mathematical model of solvent subaltion was improved. Matlab 6.5 was used to simulate the process of water droplets, and the comparison between the previous hypothesis and the improvement in this paper showed the superiority, especially in the investigation of thermodynamic equilibrium. Moreover, the separation and concentration of the complex compound dithizone-Co（Ⅱ） from aqueous phase to n-octanol by solvent sublation also proved the improved mathematical model was reasonable.展开更多
The epoxidation reaction of propylene and hydrogen peroxide with zeolite catalyst containing titaniumsilicalite (TS-1)has been studied, and the reaction in the mixed solvent of water/methanol has been discussed. It is...The epoxidation reaction of propylene and hydrogen peroxide with zeolite catalyst containing titaniumsilicalite (TS-1)has been studied, and the reaction in the mixed solvent of water/methanol has been discussed. It is shown that the selective of epoxidation propylene decreases while the selective of propylene glycol increases, when the water content increases in the mixed solvent of methanol/water.展开更多
Novel sorbent hydrogels containing acrylamide/sodium vinylsulfonate, carboxymethyl cellulose and zeolite were synthesized with free radical solution polymerization by using ammonium persulfate/<i><span style=...Novel sorbent hydrogels containing acrylamide/sodium vinylsulfonate, carboxymethyl cellulose and zeolite were synthesized with free radical solution polymerization by using ammonium persulfate/<i><span style="font-family:Verdana;">N</span></i><span style="font-family:Verdana;">,</span><i><span style="font-family:Verdana;">N</span></i><span style="font-family:Verdana;">,</span><i><span style="font-family:Verdana;">N’</span></i><span style="font-family:Verdana;">,</span><i><span style="font-family:Verdana;">N’</span></i><span style="font-family:Verdana;">-tetramethylethyle</span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">-</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">nediamine as redox initiating pair in presence of poly(ethylene glycol) diacrylate as crosslinker. It was to investigate the water uptake properties of series of the novel hydrogels, the semi IPNs and the hybrid/biohybrid composite hydrogel sorbents synthesized in this study. Water uptake studies were performed in water and in water-solvent (acetone, methanol and tetrahydrofuran) binary mixtures at 25</span></span></span><span><span><span style="font-family:;" "=""><span style="font-family:Verdana;">°</span><span style="font-family:Verdana;">C, gravimetrically. Some swelling and diffusion parameters were calculated and discussed. It has been seen that the lower equilibrium swelling factor values in all solvent compositions in comparison with the equilibrium swelling factor values in water.</span></span></span></span>展开更多
The rapid development of nuclear technology has led to more liquid organic radioactive wastes. Different from the regular aqueous radioactive wastes, these liquids possess a higher hazard potential and cannot be dispo...The rapid development of nuclear technology has led to more liquid organic radioactive wastes. Different from the regular aqueous radioactive wastes, these liquids possess a higher hazard potential and cannot be disposed through the conventional methods due to their radioactivity and chemical nature. Spent extraction solvent is a kind of common liquid organic radioactive wastes. In this work, tri-butyl phosphate(TBP), which is more difficult to degrade in the spent extraction solvent, was used as the model compound. Influences of reaction conditions on total organic carbon(TOC) removal and the volume percentage of each gas component under supercritical water oxidation(SCWO) were studied. The SCWO behaviors of spent extraction solvent simulants were studied under the optimal conditions derived from the TBP experiment. The SCWO experiments were studied at 400–550℃, oxidant stoichiometric ratio of 0–200%, feed concentration of 1.5%–4% and pressure of25 MPa for 15–75 s. The results show that the TOC removal of the simulants was greater than 99.7% and CH4,H2 and CO were not detected at 550℃, 25 MPa, oxidant stoichiometric ratio of 150%, feed concentration of3%, and residence time of 30 s.展开更多
The influence of solvent and the rate of addition of water on the characteristics of alumina-zirconia powders obtained by sol-gel method were investigated. The Al2O3-ZrO2 powders (1:1 molar ratio) were prepared using ...The influence of solvent and the rate of addition of water on the characteristics of alumina-zirconia powders obtained by sol-gel method were investigated. The Al2O3-ZrO2 powders (1:1 molar ratio) were prepared using aluminum tri-sec-butoxide and zirconium n-propoxide as precursors. Ethanol (EtOH), isopropanol (iPrOH) and isobutanol (iBuOH) were used as solvents. The Al2O3-ZrO2 powders were characterized by nitrogen physisorption (SBET), Fourier transformed infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). Prepared oxides calcined at 700℃ showed high specific surface area (200 - 240 m2/g). Obtained results suggest that the homogeneity of the mixed oxides is favored by using a water addition rate of 0.06 and 0.10 mL/min with ethanol as solvent.展开更多
基金Supported by the China Postdoctoral Science Foundation(No.2012M520164)the Fundamental Research Funds for the Central Universities(No.FRF-TP-13-008A)
文摘Three kinds of amphiphilic PMADAB gels were prepared through radiation-induced polymerization and crosslinking of methacryloxyethyl dimethylalkane ammonium bromide(MADAB) with different alkyl side chains(butyl,octyl and dodecyl).The length of alkyl side chains had significant influence on swelling behavior of the PMADAB gels in alcohol/water solvent.Equilibrium swelling degree(EDS) of PMBDAB(butyl) gel in water was ca.160 and decreased with increasing alcohol content(x),whereas EDS of PMODAB(octyl)and PMDDDAB(dodecyl) gels showed a convex-upward function of x,i.e.,these two gels barely swelled in pure water and swelled with increasing x and then shrank gradually.This phenomenon was explained by the hydrophobic association of long alkyl chains and a cosolvency effect of PMADAB in alcohol and water.The swelling behavior of PMADAB gels in methanol,ethanol and isopropanol were similar,and their EDS are related with the dielectric constant of alcohol solvents.The results suggest that PMADAB gels may be potential absorbents for various kinds of alcohols.
文摘The formamide-titanium oxide interaction mechanism is a research target of great importance for understanding the elementary events of the origin of life: the synthesis of nucleoside bases and formation of biological molecules needed for life. Titanium oxide (TiO2) can act as a strongly adsorbing surface or a catalytic material. In the present study, a comparative molecular dynamics analysis performed to clarify the adsorbing and diffusion properties of liquid formamide on a TiO2 surface in the presence of water molecules. The structural features of the formamide concentration effect (the accumulation of molecules) on a TiO2 surface in the presence and absence of water solvent are cleared up. Modification of the formamide diffusion abilities mediated by a water solvent is observed to correlate with the formamide-water concentration distribution on the surface.
文摘Achieving high energy density and fast charging of lithium-ion batteries can accelerate the promotion of electric vehicles.However,the increased mass loading causes poor charge transfer,impedes the electrochemical reaction kinetics,and limits the battery charging rate.Herein,this work demonstrated a novel pattern integrated stamping process for creating channels in the electrode,which benefits ion transport and increases the rate performance of the electrode.Meanwhile,the pressure applied during the stamping process improved the contact between electrode and current collector and also enhanced the mechanical stability of the electrode.Compared to the conventional bar-coated electrode with the same thickness of 155μm(delivered a discharge capacity of 16 mAh g^(−1) at the rate of 3 C),the stamped low-tortuosity LiFePO_(4) electrode delivered 101 mAh g^(−1) capacity.Additionally,water was employed as a solvent in this study.Owing to its eco-friendliness,high scalability,and minimal waste generation,this novel stamping technique inspire a new method for the industrial-level efficient roll to roll fabrication of fast-charge electrodes.
文摘The solvent debinding of water soluble binder in powder injection moulding (MIM) was investigated systematically, including the effects of solvent types, temperature and the thickness of green parts on the solvent debinding rate. After studying the debinding of a green part with a thickness of 4.26 mm, it was found that, the debinding rate of polyethylene glycol(PEG) in water and alcohol was high initially, and then decreased; however, it would increase with temperature increasing. At room temperature, the dissolution rate of PEG in water was higher than that in alcohol, but the latter would be much faster with temperature increasing because the debinding activation energy in alcohol was 51.44 kJ·mol -1 ·K -1 , much higher than 24.23 kJ·mol -1 ·K -1 in water. With a green part thickness larger than 4.26 mm, the debinding was controlled by diffusion; but with that smaller than 2.36 mm, the debinding was controlled by both dissolution and diffusion.
文摘Aqueous phase layer around bubble and water droplet are two additional processes in solvent sublation. In the dynamic process of mass transfer, they are always neglected, but they are very important in the investigation of thermodynamic equilibrium. In this paper, the effect of water droplet in solvent sublation was discussed in detail, and the previous mathematical model of solvent subaltion was improved. Matlab 6.5 was used to simulate the process of water droplets, and the comparison between the previous hypothesis and the improvement in this paper showed the superiority, especially in the investigation of thermodynamic equilibrium. Moreover, the separation and concentration of the complex compound dithizone-Co（Ⅱ） from aqueous phase to n-octanol by solvent sublation also proved the improved mathematical model was reasonable.
文摘The epoxidation reaction of propylene and hydrogen peroxide with zeolite catalyst containing titaniumsilicalite (TS-1)has been studied, and the reaction in the mixed solvent of water/methanol has been discussed. It is shown that the selective of epoxidation propylene decreases while the selective of propylene glycol increases, when the water content increases in the mixed solvent of methanol/water.
文摘Novel sorbent hydrogels containing acrylamide/sodium vinylsulfonate, carboxymethyl cellulose and zeolite were synthesized with free radical solution polymerization by using ammonium persulfate/<i><span style="font-family:Verdana;">N</span></i><span style="font-family:Verdana;">,</span><i><span style="font-family:Verdana;">N</span></i><span style="font-family:Verdana;">,</span><i><span style="font-family:Verdana;">N’</span></i><span style="font-family:Verdana;">,</span><i><span style="font-family:Verdana;">N’</span></i><span style="font-family:Verdana;">-tetramethylethyle</span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">-</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">nediamine as redox initiating pair in presence of poly(ethylene glycol) diacrylate as crosslinker. It was to investigate the water uptake properties of series of the novel hydrogels, the semi IPNs and the hybrid/biohybrid composite hydrogel sorbents synthesized in this study. Water uptake studies were performed in water and in water-solvent (acetone, methanol and tetrahydrofuran) binary mixtures at 25</span></span></span><span><span><span style="font-family:;" "=""><span style="font-family:Verdana;">°</span><span style="font-family:Verdana;">C, gravimetrically. Some swelling and diffusion parameters were calculated and discussed. It has been seen that the lower equilibrium swelling factor values in all solvent compositions in comparison with the equilibrium swelling factor values in water.</span></span></span></span>
基金Supported by the"Strategic Priority Research Program"of the Chinese Academy of Sciences(No.XDA02050000)
文摘The rapid development of nuclear technology has led to more liquid organic radioactive wastes. Different from the regular aqueous radioactive wastes, these liquids possess a higher hazard potential and cannot be disposed through the conventional methods due to their radioactivity and chemical nature. Spent extraction solvent is a kind of common liquid organic radioactive wastes. In this work, tri-butyl phosphate(TBP), which is more difficult to degrade in the spent extraction solvent, was used as the model compound. Influences of reaction conditions on total organic carbon(TOC) removal and the volume percentage of each gas component under supercritical water oxidation(SCWO) were studied. The SCWO behaviors of spent extraction solvent simulants were studied under the optimal conditions derived from the TBP experiment. The SCWO experiments were studied at 400–550℃, oxidant stoichiometric ratio of 0–200%, feed concentration of 1.5%–4% and pressure of25 MPa for 15–75 s. The results show that the TOC removal of the simulants was greater than 99.7% and CH4,H2 and CO were not detected at 550℃, 25 MPa, oxidant stoichiometric ratio of 150%, feed concentration of3%, and residence time of 30 s.
文摘The influence of solvent and the rate of addition of water on the characteristics of alumina-zirconia powders obtained by sol-gel method were investigated. The Al2O3-ZrO2 powders (1:1 molar ratio) were prepared using aluminum tri-sec-butoxide and zirconium n-propoxide as precursors. Ethanol (EtOH), isopropanol (iPrOH) and isobutanol (iBuOH) were used as solvents. The Al2O3-ZrO2 powders were characterized by nitrogen physisorption (SBET), Fourier transformed infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). Prepared oxides calcined at 700℃ showed high specific surface area (200 - 240 m2/g). Obtained results suggest that the homogeneity of the mixed oxides is favored by using a water addition rate of 0.06 and 0.10 mL/min with ethanol as solvent.
