Glucanases were found in the cell wall of Lilium longiflorum Thunb. pollen tubes grown in vitro . The activity of β_glucanases was, in a certain extent, decreased by nojirimycin, an inhibitor of glucosidase. P...Glucanases were found in the cell wall of Lilium longiflorum Thunb. pollen tubes grown in vitro . The activity of β_glucanases was, in a certain extent, decreased by nojirimycin, an inhibitor of glucosidase. Pollen germination percentage reduced dramatically when nojirimycin was applied in the culture medium. In case that nojirimycin was added at 0 or 1 h after the onset of incubation, the inhibition rate was 99.6% and 91.4%, respectively. When 3 mmol/L of nojirimycin was applied in the liquid medium at 0, 1, 1.5 and 2 h after the onset of incubation, the growth of pollen tubes was interrupted, which resulted in the morphological change of the pollen tubes such as the newly grown portion of pollen tubes being bent, curved and swollen. Tracing the growth pattern of the individual pollen tube grown in semi_solid medium by video microscopy, the authors demonstrated that pollen tube growth rate was strongly inhibited by nojirimycin at concentrations ranged from 0.003 to 3 mmol/L. Moreover, the cytoplasmic arrangement and the morphology of the pollen tubes were also affected by nojirimycin. The growth inhibition brought about by nojirimycin was reversible. These results indicated that β_glucanases, which degrade 1,3_β_glucan and/or 1,4_β_glucan or 1,3:1,4_β_glucan constructed in the cell wall, are involved in pollen germination and pollen tube growth. It provides new insight into an understanding of the contribution of β_glucanases to the cell wall extensibility and the crucial role of cell wall in regards to the regulation of pollen tube growth.展开更多
Numerical control(NC) bending experiments with different process parameters were carried out for 5052O aluminum alloy tubes with outer diameter of 70 mm, wall thickness of 1.5 mm, and centerline bending radius of 105 ...Numerical control(NC) bending experiments with different process parameters were carried out for 5052O aluminum alloy tubes with outer diameter of 70 mm, wall thickness of 1.5 mm, and centerline bending radius of 105 mm. And the effects of process parameters on tube wall thinning and cross section distortion were investigated. Meanwhile, acceptable bending of the 5052O aluminum tubes was accomplished based on the above experiments. The results show that the effects of process parameters on bending process for large diameter thin-walled aluminum alloy tubes are similar to those for small diameter thin-walled tubes, but the forming quality of the large diameter thin-walled aluminum alloy tubes is much more sensitive to the process parameters and thus it is more difficult to form.展开更多
The incremental constitutive relation and governing equations with combined stresses for phase transition wave propagation in a thin-walled tube are established based on the phase transition criterion considering both...The incremental constitutive relation and governing equations with combined stresses for phase transition wave propagation in a thin-walled tube are established based on the phase transition criterion considering both the hydrostatic pressure and the deviatoric stress. It is found that the centers of the initial and subsequent phase transition ellipses are shifted along the sigma-axis in the sigma tau-plane due to the tension-compression asymmetry induced by the hydrostatic pressure. The wave solution offers the 'fast' and 'slow' phase transition waves under combined longitudinal and torsional stresses in the phase transition region. The results show some new stress paths and wave structures in a thin-walled tube with phase transition, differing from those of conventional elastic-plastic materials.展开更多
An in-depth analysis of propagation characteristics ofelasto-plastic combined stress waves in circular thin-walled tubeshas been made. In obtaining the simple-wave solution, however, mostresearches have ignored the in...An in-depth analysis of propagation characteristics ofelasto-plastic combined stress waves in circular thin-walled tubeshas been made. In obtaining the simple-wave solution, however, mostresearches have ignored the influence of the circumferential stressrelated to the radial inertial ef- fect in the tubes. In this paperthe incremental elasto-plastic constitutive relations which areconve- nient for dynamic numerical analysis are adopted, and thefinite-difference method is used to study the evolution adpropagation of elasto-plastic combined stress waves in a thin-walledtube with the radial inertial effect of the tube considered. Thecalculation results are compared with those obtained when the radialinertial effect is not considered. The calculation results show thatthe radial inertial effect of a tube has a fairly great influence onthe propagation of elasto-plastic combined stress waves.展开更多
An experimental investigation was carried out to study the energy absorption characteristics of thin-walled square tubes subjected to dynamic crushing by impact loading to develop the optimum structural members. Here,...An experimental investigation was carried out to study the energy absorption characteristics of thin-walled square tubes subjected to dynamic crushing by impact loading to develop the optimum structural members. Here, the controller is introduced to improve and control the absorbed energy of thin-walled square tubes in this paper. When the controller were used, the experimental results of crushing of square tubes controlled by the controller's elements showed a good candidate for a controllable energy absorption capability in impact crushing.展开更多
In order to further improve the seismic performance of RC shear walls, a new composite shear wall with concrete filled steel tube (CFT) columns and concealed steel trusses is proposed. This new shear wall is a doubl...In order to further improve the seismic performance of RC shear walls, a new composite shear wall with concrete filled steel tube (CFT) columns and concealed steel trusses is proposed. This new shear wall is a double composite shear wall; the first composite being the use of three different force systems, CFT, steel truss and shear wall, and the second the use of two different materials, steel and concrete. Three 1/5 scaled experimental specimens: a traditional RC shear wall, a shear wall with CFT columns, and a shear wall with CFT columns and concealed steel trusses, were tested under cyclic loading and the seismic performance indices of the shear walls were comparatively analyzed. Based on the data from these experiments, a thorough elastic-plastic finite element analysis and parametric analysis of the new shear walls were carried out using ABAQUS software. The finite element results of deformation, stress distribution, and the evolution of cracks in each phase were compared with the experimental results and showed good agreement. A mechanical model was also established for calculating the load-carrying capacity of the new composite shear walls. The results show that this new type of shear wall has improved seismic performance over the other two types of shear wails tested.展开更多
Assessment of the magnitude and pattern of wall shear stress(WSS)in vivo is the prerequisite for studying the quantitative relationship between exercise-induced WSS and arterial endothelial function.In the previous st...Assessment of the magnitude and pattern of wall shear stress(WSS)in vivo is the prerequisite for studying the quantitative relationship between exercise-induced WSS and arterial endothelial function.In the previous studies,the calculation of the WSS modulated by exercise training was primarily based upon the rigid tube model,which did not take non-linear effects of vessel elastic deformation into consideration.In this study,with an elastic tube model,we estimated the effect of a bout of 30-minute acute cycling exercise on the WSS and the flow rate in the common carotid artery according to the measured inner diameter,center-line blood flow velocity,heart rates and the brachial blood pressures before and after exercise training.Furthermore,the roles of exerciseinduced arterial diameter and blood flow rate in the change of WSS were also determined.The numerical results demonstrate that acute exercise significantly increases the magnitudes of blood flow rate and WSS.Moreover,the vessel elastic deformation is a non-negligible factor in the calculation of the WSS induced by exercise,which generates greater effects on the minimum WSS than the maximum WSS.Additionally,the contributions of exercise-induced variations in blood flow rate and diameter are almost identical in the change of the mean WSS.展开更多
The spinning deformation of thin walled tube in necking process is simulated with a dynamic explicit FEM program,LS DYNA3D and the distributions of Cauchy strains and thickness are analyzed through time history to a...The spinning deformation of thin walled tube in necking process is simulated with a dynamic explicit FEM program,LS DYNA3D and the distributions of Cauchy strains and thickness are analyzed through time history to achieve a good understanding of the deformation in necking process by spinning and the numerical simulation results are in good agreement with the test results.展开更多
The effect of frictions between dies and tube on the cross section quality of thin-walled tube numerical controlled(NC) bending was studied by numerical simulation method, combined with theoretical analysis and experi...The effect of frictions between dies and tube on the cross section quality of thin-walled tube numerical controlled(NC) bending was studied by numerical simulation method, combined with theoretical analysis and experiment. The results show that the frictions between mandrel, wiper, pressure die, bending die and tube have a significant and complicate effect on the section quality of thin-walled tube NC bending. To improve the section quality, frictions between mandrel, wiper and tube should be decreased, but the frictions between the pressure die, bending die and tube increase. The effect on the section distortion is more significant from mandrel, wiper, pressure die to bending die and the effect on the wall thinning more significant from mandrel, pressure die, wiper, to bending die. The effects of frictions between all dies and tube on wall thinning are smaller than their effects on section distortion. Mandrel and wiper should be lubricated well and drawing oil is used to lubricate them in actual production. The frictions between pressure die, bending die and tube should be increased and the dry friction is used between pressure die, bending die and tube in actual production.展开更多
Theoretical analyses show that the variation of wall thickness is in direct proportion to outer-diameter, inter-diameter, and (1+R_s)^(1/2) (Rs is sectional increase ratio of tube), the theoretical calculated results ...Theoretical analyses show that the variation of wall thickness is in direct proportion to outer-diameter, inter-diameter, and (1+R_s)^(1/2) (Rs is sectional increase ratio of tube), the theoretical calculated results of wall thickness during tube dieless upsetting are very approximate to the experimental one. As the width of deformation field increases, both the variation of wall thickness and the derivative of wall thickness variation to width of deformation field (to/tf) reduce.展开更多
A new horizontal continuous casting method with heating-cooling combined mold (HCCM) technology was explored for fabri- cating high-quality thin-wall cupronickel alloy tubes used for heat exchange pipes. The microst...A new horizontal continuous casting method with heating-cooling combined mold (HCCM) technology was explored for fabri- cating high-quality thin-wall cupronickel alloy tubes used for heat exchange pipes. The microstructure and mechanical properties of BFe 10 cupronickel alloy tubes fabricated by HCCM and traditional continuous casting (cooling mold casting) were comparatively investigated. The results show that the tube fabricated by HCCM has smooth internal and external surfaces without any defects, and its internal and external surface roughnesses are 0.64 μm and 0.85 μm, respectively. The tube could be used for subsequent cold processing without other treatments such as surface planning, milling and acid-washing. This indicates that HCCM can effectively reduce the process flow and improve the pro- duction efficiency of a BFel0 cupronickel alloy tube. The tube has columnar grains along its axial direction with a major casting texture of {012}〈 621 〉. Compared with cooling mold casting (6 = 36.5%), HCCM can improve elongation (3 = 46.3%) by 10% with a slight loss of strength, which indicates that HCCM remarkably improves the cold extension performance of a BFe 10 cupronickel alloy tube.展开更多
The effect of mandrel with the structure of ball and socket on the cross section quality of thin-walled tube numerical controlled(NC) bending was studied by numerical simulation method, combined with theoretical (anal...The effect of mandrel with the structure of ball and socket on the cross section quality of thin-walled tube numerical controlled(NC) bending was studied by numerical simulation method, combined with theoretical (analysis) and experiment. Influencing factors of the mandrel include the count of mandrel heads, the diameter of mandrel and its position. According to the principle of NC tube bending, quality defects possibly produced in thin-walled tube NC bending process were analyzed and two parameters were proposed in order to describe the cross section quality of thin-walled tube NC bending. According to the geometrical dimension of tube and dies, the range of mandrel protrusion was derived. The finite element model of thin-walled tube NC bending was established based on the DYNAFORM platform, and key technological problems were solved. The model was verified by experiment. The effect of the number of mandrel heads, the diameter of mandrel and the protrusion length of mandrel on the cross section quality of thin-walled tube NC bending was revealed and how to choose mandrel parameters was presented.展开更多
High frequency shock load is often generated during pyrotechnic device working, which is detrimental to spacecraft structures and electric devices. Therefore, it is valuable to reduce the shock load in pyrotechnic dev...High frequency shock load is often generated during pyrotechnic device working, which is detrimental to spacecraft structures and electric devices. Therefore, it is valuable to reduce the shock load in pyrotechnic device design. Actually, there are several ways to decrease pyroshock loads, such as reduction of powder,installation of buffering structure, insulation of damageable devices, and so on. Considered assuring the function of pyrotechnic device and minimum of structure modification, shock absorbing structure is more propitious to be introduced in pyrotechnic device. In this paper, based on the method of thinwalled metal tube diameter-expanding, a thin-walled tube shock buffering structure was designed on a separate bolt. Built on the simplified structure of a separate bolt, the model of cone piston impacting thin-walled tube absorber was established, and the thin-walled tube shock absorbing characteristics and the relation between cone angles and absorber performance were analyzed. The results showed that the change of buffering force of thin-walled tube could be divided into four phases, and each phase was correspondent to the cone piston structure. In addition, as the cone angle increases, the max shock acceleration changes in the style of decrease-increase-decrease-increase, which is the result of coupled effects of cone piston max enter depth, buffering force and energy loss. In short, these results could establish the relationships between thin-walled tube absorbing performance and its structure, which is of significance to develop low-shock pyrotechnic device.展开更多
The springback is one of the key factors which affect the forming quality of thin-walled tube NC precision bending. The elastic-plastic finite element method was proposed to study the springback process of thin-walled...The springback is one of the key factors which affect the forming quality of thin-walled tube NC precision bending. The elastic-plastic finite element method was proposed to study the springback process of thin-walled tube NC precision bending and the combination of dynamic explicit algorithm and the static implicit algorithm was proposed to solve the whole process of thin-walled tube NC precision bending. Then, the 3D elastic-plastic finite element model was established based on the DYNAFORM platform, and the model was verified to be reasonable. At last, the springback rule of thin-walled tube NC precision bending and the effect of geometry and material parameters on the springback rule of thin-walled tube NC precision bending were studied, which is useful to controlling the springback of thin-walled tube NC precision bending, and the numerical simulation method can be used to study other effect of parameters on the forming quality of thin-walled tube NC precision bending.展开更多
Tube spinning technology is one of the effective methods of manufacturing large diameter thin-walled shapes. In this research, effects of major parameters of thermo mechanical tube spinning process such as preform'...Tube spinning technology is one of the effective methods of manufacturing large diameter thin-walled shapes. In this research, effects of major parameters of thermo mechanical tube spinning process such as preform's thickness, percentage of thickness reduction, mandrel rotational speed, feed rate, solution treatment time and aging treatment time on the wall thickness changes and process time in thermo-mechanical tube spinning process for fabrication of 2024 aluminum spun tubes using design of experiments (DOE), are studied. The statistical results are verified through some experiments. Results of experimental evaluation are analyzed by variance analysis and mathematic models are obtained. Finally using these models, input parameters for optimum production are achieved.展开更多
Cross-section deformation is one of important factors affecting the quality of tube formation, and the tube's capability of transporting liquid and gas will be reduced because of the cross-section ellipse deformation...Cross-section deformation is one of important factors affecting the quality of tube formation, and the tube's capability of transporting liquid and gas will be reduced because of the cross-section ellipse deformation due to the effect of shear load in plastic bending process. When the tube is bent, the extrados-wall bears the tension stress and the intrados-wall bears the compression stress, synchronously the cross-section is affected by the circumferential stress. According to the above, the distribution function and curve of tangential stress can be obtained according to force balance differential equations on circumferential direction and Trasca rule. Subsequently the real state and virtual state moment equations were established, a new method was presented adopting the virtual principle of deformation system to calculate the x-axis and y-axis displacement of arbitrary point on cross-section. So the major and minor axes of deformed cross-section can be calculated according to the displacements of each point, and the variety value of major and minor axes will be obtained further. Finally the theoretical calculating result is compared with NC tube rotary-bending experiment results to verify the rationality of theoretical analysis, and the cross-section deformation rule of thin-walled tube can be received.展开更多
Recent experiments revealed many new phenomena of the macroscopic domain patterns in the stress-induced phase transformation of a superelastic polycrystalline NiTi tube during tensile loading. The new phenomena includ...Recent experiments revealed many new phenomena of the macroscopic domain patterns in the stress-induced phase transformation of a superelastic polycrystalline NiTi tube during tensile loading. The new phenomena include deformation instability with the formation of a helical domain, domain topology transition from helix to cylinder, domain-front branching and loading-path dependence of domain patterns. In this paper, we model the polycrystal as an elastic continuum with nonconvex strain energy and adopt the non-local strain gradient energy to account for the energy of the diffusive domain front. We simulate the equilibrium domain patterns and their evolution in the tubes under tensile loading by a non-local Finite Element Method (FEM). It is revealed that the observed loading-path dependence and topology transition of do- main patterns are due to the thermodynamic metastability of the tube system. The computation also shows that the tube-wall thickness has a significant effect on the domain patterns: with fixed material properties and interfacial energy density, a large tube-wall thickness leads to a long and slim helical domain and a severe branching of the cylindrical-domain front.展开更多
The thin-walled tube flexure(TWTF) hinges have important potential application value in the deployment mechanisms of satellite and solar array, but the optimal design of the TWTF hinges haven't been completely solv...The thin-walled tube flexure(TWTF) hinges have important potential application value in the deployment mechanisms of satellite and solar array, but the optimal design of the TWTF hinges haven't been completely solved, which restricts their applications. An optimal design method for the qusai-static folding and deploying of TWTF hinges with double slots is presented based on the response surface theory. Firstly, the full factorial method is employed to design of the experiments. Then, the finite element models of the TWTF hinges with double slots are constructed to simulate the qusai-static folding and deploying non-linear analysis. What's more, the mathematical model of the TWTF flexure hinge quasi-static folding and deploying properties are derived by the response surface method. Considering of small mass and high stability, the peak moment of quasi-static folding and deploying as well as the lightless are set as the objectives to get the optimal performances. The relative errors of the objectives between the optimal design results and the FE analysis results are less than 7%, which demonstrates the precision of the surrogate models. Lastly, the parameter study shows that both the slots length and the slots width both have significant effects to the peak moment of quasi-static folding and deploying of TWTF hinges with double slots. However, the maximum Mises stress of quasi-static folding is more sensitive to the slots length than the slots width. The proposed research can be applied to optimize other thin-walled flexure hinges under quasi-static folding and deploying, which is of great importance to design of flexure hinges with high stability and low stress.展开更多
Springback is one of important factors influencing the forming quality of numerical control (NC) bending of thin-walled tube. In this paper, a numerical-analytic method for springback angle prediction of the process...Springback is one of important factors influencing the forming quality of numerical control (NC) bending of thin-walled tube. In this paper, a numerical-analytic method for springback angle prediction of the process was put forward. The method is based on springback angle model derived using analytic method and simulation results from three-dimensional (3D) rigid-plastic finite element method (FEM). The method is validated through comparison with experimental results. The features of the method are as follows: (1) The method is high in efficiency because it combines advantages of rigid-plastic FEM and analytic method. (2) The method is satisfactory in accuracy, since the field variables used in the model is resulting from 3D rigid-plastic FEM solution, and the effects both of axial force and strain neutral axis shift have been included. (3) Research on multi-factor effects can be carried out using the method due to its advantage inheriting from rigid-plastic FEM. The method described here is also of general significance to other bending processes.展开更多
A theoretical investigation on the structural and elastic properties of ZnO nanotubes is carried out by using atomistic calculations based on an inter-atomic pair potential within the shell-model approach. The calcula...A theoretical investigation on the structural and elastic properties of ZnO nanotubes is carried out by using atomistic calculations based on an inter-atomic pair potential within the shell-model approach. The calculation results are presented for the bond length, bond angle, radius dilation, strain energy, Young modulus and Poisson ratio as a function of tube radius. For small tube radius these properties depend on the helicity of the tube, while for the tube radius larger than 6.0A, they are independent of the tube radius and helicity except for the strain energy which decreases with increasing tube radius.展开更多
文摘Glucanases were found in the cell wall of Lilium longiflorum Thunb. pollen tubes grown in vitro . The activity of β_glucanases was, in a certain extent, decreased by nojirimycin, an inhibitor of glucosidase. Pollen germination percentage reduced dramatically when nojirimycin was applied in the culture medium. In case that nojirimycin was added at 0 or 1 h after the onset of incubation, the inhibition rate was 99.6% and 91.4%, respectively. When 3 mmol/L of nojirimycin was applied in the liquid medium at 0, 1, 1.5 and 2 h after the onset of incubation, the growth of pollen tubes was interrupted, which resulted in the morphological change of the pollen tubes such as the newly grown portion of pollen tubes being bent, curved and swollen. Tracing the growth pattern of the individual pollen tube grown in semi_solid medium by video microscopy, the authors demonstrated that pollen tube growth rate was strongly inhibited by nojirimycin at concentrations ranged from 0.003 to 3 mmol/L. Moreover, the cytoplasmic arrangement and the morphology of the pollen tubes were also affected by nojirimycin. The growth inhibition brought about by nojirimycin was reversible. These results indicated that β_glucanases, which degrade 1,3_β_glucan and/or 1,4_β_glucan or 1,3:1,4_β_glucan constructed in the cell wall, are involved in pollen germination and pollen tube growth. It provides new insight into an understanding of the contribution of β_glucanases to the cell wall extensibility and the crucial role of cell wall in regards to the regulation of pollen tube growth.
基金Project(50225518) supported by the National Science Foundation of China for Distinguished Young ScholarsProject(59975076, 50175092) supported by the National Natural Science Foundation of ChinaProject(04H53057) supported by the Aviation Science Foundation of China
文摘Numerical control(NC) bending experiments with different process parameters were carried out for 5052O aluminum alloy tubes with outer diameter of 70 mm, wall thickness of 1.5 mm, and centerline bending radius of 105 mm. And the effects of process parameters on tube wall thinning and cross section distortion were investigated. Meanwhile, acceptable bending of the 5052O aluminum tubes was accomplished based on the above experiments. The results show that the effects of process parameters on bending process for large diameter thin-walled aluminum alloy tubes are similar to those for small diameter thin-walled tubes, but the forming quality of the large diameter thin-walled aluminum alloy tubes is much more sensitive to the process parameters and thus it is more difficult to form.
基金Project supported by the National Natural Science Foundation of China(No.11072240)
文摘The incremental constitutive relation and governing equations with combined stresses for phase transition wave propagation in a thin-walled tube are established based on the phase transition criterion considering both the hydrostatic pressure and the deviatoric stress. It is found that the centers of the initial and subsequent phase transition ellipses are shifted along the sigma-axis in the sigma tau-plane due to the tension-compression asymmetry induced by the hydrostatic pressure. The wave solution offers the 'fast' and 'slow' phase transition waves under combined longitudinal and torsional stresses in the phase transition region. The results show some new stress paths and wave structures in a thin-walled tube with phase transition, differing from those of conventional elastic-plastic materials.
文摘An in-depth analysis of propagation characteristics ofelasto-plastic combined stress waves in circular thin-walled tubeshas been made. In obtaining the simple-wave solution, however, mostresearches have ignored the influence of the circumferential stressrelated to the radial inertial ef- fect in the tubes. In this paperthe incremental elasto-plastic constitutive relations which areconve- nient for dynamic numerical analysis are adopted, and thefinite-difference method is used to study the evolution adpropagation of elasto-plastic combined stress waves in a thin-walledtube with the radial inertial effect of the tube considered. Thecalculation results are compared with those obtained when the radialinertial effect is not considered. The calculation results show thatthe radial inertial effect of a tube has a fairly great influence onthe propagation of elasto-plastic combined stress waves.
文摘An experimental investigation was carried out to study the energy absorption characteristics of thin-walled square tubes subjected to dynamic crushing by impact loading to develop the optimum structural members. Here, the controller is introduced to improve and control the absorbed energy of thin-walled square tubes in this paper. When the controller were used, the experimental results of crushing of square tubes controlled by the controller's elements showed a good candidate for a controllable energy absorption capability in impact crushing.
基金Science and Technology Key Project of Beijing Under Grant No.D0905060370000National Natural Science Foundation of China Under Grant No.50878007+1 种基金Project High-level Personnel in Beijing Under Grant No.PHR20100502the Scientific and Technological Planning of Beijing Key Project Education Commission Under Grant No.KZ200910005008
文摘In order to further improve the seismic performance of RC shear walls, a new composite shear wall with concrete filled steel tube (CFT) columns and concealed steel trusses is proposed. This new shear wall is a double composite shear wall; the first composite being the use of three different force systems, CFT, steel truss and shear wall, and the second the use of two different materials, steel and concrete. Three 1/5 scaled experimental specimens: a traditional RC shear wall, a shear wall with CFT columns, and a shear wall with CFT columns and concealed steel trusses, were tested under cyclic loading and the seismic performance indices of the shear walls were comparatively analyzed. Based on the data from these experiments, a thorough elastic-plastic finite element analysis and parametric analysis of the new shear walls were carried out using ABAQUS software. The finite element results of deformation, stress distribution, and the evolution of cracks in each phase were compared with the experimental results and showed good agreement. A mechanical model was also established for calculating the load-carrying capacity of the new composite shear walls. The results show that this new type of shear wall has improved seismic performance over the other two types of shear wails tested.
基金The research described in this paper was supported in part by the National Natural Science Foundation of China(Grant No.31370948,11672065).
文摘Assessment of the magnitude and pattern of wall shear stress(WSS)in vivo is the prerequisite for studying the quantitative relationship between exercise-induced WSS and arterial endothelial function.In the previous studies,the calculation of the WSS modulated by exercise training was primarily based upon the rigid tube model,which did not take non-linear effects of vessel elastic deformation into consideration.In this study,with an elastic tube model,we estimated the effect of a bout of 30-minute acute cycling exercise on the WSS and the flow rate in the common carotid artery according to the measured inner diameter,center-line blood flow velocity,heart rates and the brachial blood pressures before and after exercise training.Furthermore,the roles of exerciseinduced arterial diameter and blood flow rate in the change of WSS were also determined.The numerical results demonstrate that acute exercise significantly increases the magnitudes of blood flow rate and WSS.Moreover,the vessel elastic deformation is a non-negligible factor in the calculation of the WSS induced by exercise,which generates greater effects on the minimum WSS than the maximum WSS.Additionally,the contributions of exercise-induced variations in blood flow rate and diameter are almost identical in the change of the mean WSS.
文摘The spinning deformation of thin walled tube in necking process is simulated with a dynamic explicit FEM program,LS DYNA3D and the distributions of Cauchy strains and thickness are analyzed through time history to achieve a good understanding of the deformation in necking process by spinning and the numerical simulation results are in good agreement with the test results.
基金Project(50225518) supported by the National Science Foundation of China for Distinguished Young Scholars Projects(50175092+4 种基金 59975076) supported by the National Natural Science Foundation of China Project supported by the Teaching and Research Award Program for Outstanding Young Teachers in Higher Education Institutions of MOE, China Project(04H53057) supported by the Aeronautical Science Foundation of China Project(20020699002) supported by the Specialized Research Fund for the Doctoral Program of Higher Education, China Project(Z200518) supported by the Graduate Starting Seed Fund of Northwestern Polytechnical University, China
文摘The effect of frictions between dies and tube on the cross section quality of thin-walled tube numerical controlled(NC) bending was studied by numerical simulation method, combined with theoretical analysis and experiment. The results show that the frictions between mandrel, wiper, pressure die, bending die and tube have a significant and complicate effect on the section quality of thin-walled tube NC bending. To improve the section quality, frictions between mandrel, wiper and tube should be decreased, but the frictions between the pressure die, bending die and tube increase. The effect on the section distortion is more significant from mandrel, wiper, pressure die to bending die and the effect on the wall thinning more significant from mandrel, pressure die, wiper, to bending die. The effects of frictions between all dies and tube on wall thinning are smaller than their effects on section distortion. Mandrel and wiper should be lubricated well and drawing oil is used to lubricate them in actual production. The frictions between pressure die, bending die and tube should be increased and the dry friction is used between pressure die, bending die and tube in actual production.
基金Sponsored by Ministry of Education of China and Natural Science Foundation of Liaoning Province
文摘Theoretical analyses show that the variation of wall thickness is in direct proportion to outer-diameter, inter-diameter, and (1+R_s)^(1/2) (Rs is sectional increase ratio of tube), the theoretical calculated results of wall thickness during tube dieless upsetting are very approximate to the experimental one. As the width of deformation field increases, both the variation of wall thickness and the derivative of wall thickness variation to width of deformation field (to/tf) reduce.
基金supported by the National High Technology Research and Development Program of China (No.2011BAE23B00)
文摘A new horizontal continuous casting method with heating-cooling combined mold (HCCM) technology was explored for fabri- cating high-quality thin-wall cupronickel alloy tubes used for heat exchange pipes. The microstructure and mechanical properties of BFe 10 cupronickel alloy tubes fabricated by HCCM and traditional continuous casting (cooling mold casting) were comparatively investigated. The results show that the tube fabricated by HCCM has smooth internal and external surfaces without any defects, and its internal and external surface roughnesses are 0.64 μm and 0.85 μm, respectively. The tube could be used for subsequent cold processing without other treatments such as surface planning, milling and acid-washing. This indicates that HCCM can effectively reduce the process flow and improve the pro- duction efficiency of a BFel0 cupronickel alloy tube. The tube has columnar grains along its axial direction with a major casting texture of {012}〈 621 〉. Compared with cooling mold casting (6 = 36.5%), HCCM can improve elongation (3 = 46.3%) by 10% with a slight loss of strength, which indicates that HCCM remarkably improves the cold extension performance of a BFe 10 cupronickel alloy tube.
文摘The effect of mandrel with the structure of ball and socket on the cross section quality of thin-walled tube numerical controlled(NC) bending was studied by numerical simulation method, combined with theoretical (analysis) and experiment. Influencing factors of the mandrel include the count of mandrel heads, the diameter of mandrel and its position. According to the principle of NC tube bending, quality defects possibly produced in thin-walled tube NC bending process were analyzed and two parameters were proposed in order to describe the cross section quality of thin-walled tube NC bending. According to the geometrical dimension of tube and dies, the range of mandrel protrusion was derived. The finite element model of thin-walled tube NC bending was established based on the DYNAFORM platform, and key technological problems were solved. The model was verified by experiment. The effect of the number of mandrel heads, the diameter of mandrel and the protrusion length of mandrel on the cross section quality of thin-walled tube NC bending was revealed and how to choose mandrel parameters was presented.
文摘High frequency shock load is often generated during pyrotechnic device working, which is detrimental to spacecraft structures and electric devices. Therefore, it is valuable to reduce the shock load in pyrotechnic device design. Actually, there are several ways to decrease pyroshock loads, such as reduction of powder,installation of buffering structure, insulation of damageable devices, and so on. Considered assuring the function of pyrotechnic device and minimum of structure modification, shock absorbing structure is more propitious to be introduced in pyrotechnic device. In this paper, based on the method of thinwalled metal tube diameter-expanding, a thin-walled tube shock buffering structure was designed on a separate bolt. Built on the simplified structure of a separate bolt, the model of cone piston impacting thin-walled tube absorber was established, and the thin-walled tube shock absorbing characteristics and the relation between cone angles and absorber performance were analyzed. The results showed that the change of buffering force of thin-walled tube could be divided into four phases, and each phase was correspondent to the cone piston structure. In addition, as the cone angle increases, the max shock acceleration changes in the style of decrease-increase-decrease-increase, which is the result of coupled effects of cone piston max enter depth, buffering force and energy loss. In short, these results could establish the relationships between thin-walled tube absorbing performance and its structure, which is of significance to develop low-shock pyrotechnic device.
基金Project(50225518) supported by the National Science Foundation of China for Distinguished Young Scholars Projects(50175092 59975076) supported by the National Natural Science Foundation of ChinaProject supported by the Teaching and Research Award Program for Outstanding Young Teachers in Higher Education Institutions of MOE, PRC Project(04H53057) supported by the Aeronautical Science Foundation of China Project(Z200518) supported by the Graduate Starting Seed Fund of Northwestern Polytechnical University Project(20020699002) supported by the Specialized Research Fund for the Doctoral Program of Higher Education
文摘The springback is one of the key factors which affect the forming quality of thin-walled tube NC precision bending. The elastic-plastic finite element method was proposed to study the springback process of thin-walled tube NC precision bending and the combination of dynamic explicit algorithm and the static implicit algorithm was proposed to solve the whole process of thin-walled tube NC precision bending. Then, the 3D elastic-plastic finite element model was established based on the DYNAFORM platform, and the model was verified to be reasonable. At last, the springback rule of thin-walled tube NC precision bending and the effect of geometry and material parameters on the springback rule of thin-walled tube NC precision bending were studied, which is useful to controlling the springback of thin-walled tube NC precision bending, and the numerical simulation method can be used to study other effect of parameters on the forming quality of thin-walled tube NC precision bending.
文摘Tube spinning technology is one of the effective methods of manufacturing large diameter thin-walled shapes. In this research, effects of major parameters of thermo mechanical tube spinning process such as preform's thickness, percentage of thickness reduction, mandrel rotational speed, feed rate, solution treatment time and aging treatment time on the wall thickness changes and process time in thermo-mechanical tube spinning process for fabrication of 2024 aluminum spun tubes using design of experiments (DOE), are studied. The statistical results are verified through some experiments. Results of experimental evaluation are analyzed by variance analysis and mathematic models are obtained. Finally using these models, input parameters for optimum production are achieved.
基金supported by "Eleven Five Years Plan" Basic Research Item of National Defense of China (Grant No. B2220060048)
文摘Cross-section deformation is one of important factors affecting the quality of tube formation, and the tube's capability of transporting liquid and gas will be reduced because of the cross-section ellipse deformation due to the effect of shear load in plastic bending process. When the tube is bent, the extrados-wall bears the tension stress and the intrados-wall bears the compression stress, synchronously the cross-section is affected by the circumferential stress. According to the above, the distribution function and curve of tangential stress can be obtained according to force balance differential equations on circumferential direction and Trasca rule. Subsequently the real state and virtual state moment equations were established, a new method was presented adopting the virtual principle of deformation system to calculate the x-axis and y-axis displacement of arbitrary point on cross-section. So the major and minor axes of deformed cross-section can be calculated according to the displacements of each point, and the variety value of major and minor axes will be obtained further. Finally the theoretical calculating result is compared with NC tube rotary-bending experiment results to verify the rationality of theoretical analysis, and the cross-section deformation rule of thin-walled tube can be received.
文摘Recent experiments revealed many new phenomena of the macroscopic domain patterns in the stress-induced phase transformation of a superelastic polycrystalline NiTi tube during tensile loading. The new phenomena include deformation instability with the formation of a helical domain, domain topology transition from helix to cylinder, domain-front branching and loading-path dependence of domain patterns. In this paper, we model the polycrystal as an elastic continuum with nonconvex strain energy and adopt the non-local strain gradient energy to account for the energy of the diffusive domain front. We simulate the equilibrium domain patterns and their evolution in the tubes under tensile loading by a non-local Finite Element Method (FEM). It is revealed that the observed loading-path dependence and topology transition of do- main patterns are due to the thermodynamic metastability of the tube system. The computation also shows that the tube-wall thickness has a significant effect on the domain patterns: with fixed material properties and interfacial energy density, a large tube-wall thickness leads to a long and slim helical domain and a severe branching of the cylindrical-domain front.
基金supported by National Natural Science Foundation ofChina(Grant No.50935002)
文摘The thin-walled tube flexure(TWTF) hinges have important potential application value in the deployment mechanisms of satellite and solar array, but the optimal design of the TWTF hinges haven't been completely solved, which restricts their applications. An optimal design method for the qusai-static folding and deploying of TWTF hinges with double slots is presented based on the response surface theory. Firstly, the full factorial method is employed to design of the experiments. Then, the finite element models of the TWTF hinges with double slots are constructed to simulate the qusai-static folding and deploying non-linear analysis. What's more, the mathematical model of the TWTF flexure hinge quasi-static folding and deploying properties are derived by the response surface method. Considering of small mass and high stability, the peak moment of quasi-static folding and deploying as well as the lightless are set as the objectives to get the optimal performances. The relative errors of the objectives between the optimal design results and the FE analysis results are less than 7%, which demonstrates the precision of the surrogate models. Lastly, the parameter study shows that both the slots length and the slots width both have significant effects to the peak moment of quasi-static folding and deploying of TWTF hinges with double slots. However, the maximum Mises stress of quasi-static folding is more sensitive to the slots length than the slots width. The proposed research can be applied to optimize other thin-walled flexure hinges under quasi-static folding and deploying, which is of great importance to design of flexure hinges with high stability and low stress.
基金This work was supported by the National Natural Science Foundation of China for Distinguished Young Scholars (Grant No. 50225518)the Teaching and Research Award Program for 0utstanding Young Teachers in Higher Education Institution of M0E, PRCthe Aeronautical Science Foundation of China (Grant No. 04H53057).
文摘Springback is one of important factors influencing the forming quality of numerical control (NC) bending of thin-walled tube. In this paper, a numerical-analytic method for springback angle prediction of the process was put forward. The method is based on springback angle model derived using analytic method and simulation results from three-dimensional (3D) rigid-plastic finite element method (FEM). The method is validated through comparison with experimental results. The features of the method are as follows: (1) The method is high in efficiency because it combines advantages of rigid-plastic FEM and analytic method. (2) The method is satisfactory in accuracy, since the field variables used in the model is resulting from 3D rigid-plastic FEM solution, and the effects both of axial force and strain neutral axis shift have been included. (3) Research on multi-factor effects can be carried out using the method due to its advantage inheriting from rigid-plastic FEM. The method described here is also of general significance to other bending processes.
基金Supported by the National Natural Science Foundation of China under Grant Nos 10025420, 10574121 and 90406024, the Ministry of Education of China, and Chinese Academy of Sciences.
文摘A theoretical investigation on the structural and elastic properties of ZnO nanotubes is carried out by using atomistic calculations based on an inter-atomic pair potential within the shell-model approach. The calculation results are presented for the bond length, bond angle, radius dilation, strain energy, Young modulus and Poisson ratio as a function of tube radius. For small tube radius these properties depend on the helicity of the tube, while for the tube radius larger than 6.0A, they are independent of the tube radius and helicity except for the strain energy which decreases with increasing tube radius.