Comparison study on measurement of rail weld joint between inertial reference method and multi-point chord reference method

Purpose – Straightness measurement of rail weld joint is of essential importance to railway maintenance. Dueto the lack of efficient measurement equipment, there has been limited in-depth research on rail weld joint with a5-m wavelength range, leaving a significant knowledge gap in this field.Design/methodology/approach – In this study, the authors used the well-established inertial referencemethod (IR-method), and the state-of-the-art multi-point chord reference method (MCR-method). Two methodshave been applied in different types of rail straightness measurement trollies, respectively. These instrumentswere tested in a high-speed rail section within a certain region of China. The test results were ultimatelyvalidated through using traditional straightedge and feeler gauge methods as reference data to evaluate the railweld joint straightness within the 5-m wavelength range.Findings – The research reveals that IR-method and MCR-method produce reasonably similar measurementresults for wavelengths below 1 m. However, MCR-method outperforms IR-method in terms of accuracy forwavelengths exceeding 3 m. Furthermore, it was observed that IR-method, while operating at a slower speed,carries the risk of derailing and is incapable of detecting rail weld joints and low joints within the track.Originality/value – The research compare two methods’ measurement effects in a longer wavelength rangeand demonstrate the superiority of MCR-method.

Performance analysis of optical burst switching node with limited wavelength conversion capabilities

The systematical and scalable frameworks were provided for estimating the blocking probabilities under asynchronous traffic in optical burst switching(OBS) nodes with limited wavelength conversion capability(LWCC) . The relevant system architectures of limited range and limited number of wavelength converters(WCs) deployed by a share-per-fiber(SPF) mode were developed,and the novel theoretical analysis of node blocking probability was derived by combining the calculation of discouraged arrival rate in a birth-death process and two-dimensional Markov chain model of SPF. The simulation results on single node performance verify the accuracy and effectiveness of the analysis models. Under most scenarios,it is difficult to distinguish the plots generated by the analysis and simulation. As the conversion degree increases,the accuracy of the analysis model worsens slightly. However,the utmost error on burst loss probability is far less than one order of magnitude and hence,still allows for an accurate estimate. Some results are of actual significance to the construction of next-generation commercial OBS backbones.

Comparison the Theoretical and Experimental Results of Radio Absorbing Properties of Au Thin Films in 8-11.6 GHz Band

The comparison of theoretical and experimental results of measurements of absorbing properties of Au films of 10 nm thickness deposited on a polymer substrate in the frequency band 8-11.6 GHz electromagnetic radiation are presented. The new configuration of Au thin film in a rectangular waveguide had been considered. An abnormally high level of absorption of electromagnetic radiation throughout the range of wavelengths was obtained. This is apparently due to the lack of galvanic contact between the film and waveguide.

Physical design of a wavelength tunable fully coherent VUV source using a self-seeding free electron laser

In order to meet the requirements of the synchrotron radiation users, a fully coherent VUV free electron laser （FEL） has been preliminarily designed. One important goal of this design is that the radiation wavelength can be easily tuned in a broad range （70 170 nm）. In the light of the users＇ demand and our actual conditions, the self-seeding scheme is adopted for this proposal. Firstly, we attempted to fix the electron energy and only changed the undulator gap to vary the radiation wavelength; however, our analysis implies that this is difficult because of the great difference of the power gain length and FEL efficiency at different wavelengths. Therefore, we have considered dividing the wavelength range into three subareas. In each subarea, a constant electron energy is used and the wavelength tuning is realized only by adjusting the undulator gap. The simulation results show that this scheme has an acceptable performance.

Loss characteristics of helical-core fiber

A special optical fiber is investigated, which has a helical core in the cylindrical cladding. The beam propagation method （BPM） is used for analyzing the impacts of the geometric and physical parameters on the properties of mode losses of the helical-core fiber. The propagation loss is 0.32 dB/m for the fundamental mode and the propagation loss is 20.95 dB/m for the LPu mode in the wavelength range of 1050-1065 nm when the core diameter is 19 μm, the pitch of the core＇s helix is 2.66 mm, and the offset of the helix core from the center of the fiber axis is 31 μm. The core diameter of the single-mode helical-core fiber well exceeds that of the conventional large-mode-area fiber. The helical-core fiber can provide the effec- tive large-mode-area single-mode operation without coiling fiber or selecting excitation mode.