FeCrAl fiber-reinforced hydroxyapatite（HA） biocomposites（FeCrAl（f）/HA） were fabricated by the hot pressing technique.The metallographic microscopy,X-ray diffractometry,scanning electron microscopy（SEM） and ene...FeCrAl fiber-reinforced hydroxyapatite（HA） biocomposites（FeCrAl（f）/HA） were fabricated by the hot pressing technique.The metallographic microscopy,X-ray diffractometry,scanning electron microscopy（SEM） and energy dispersive spectroscopy（EDS） were used to observe and analyze the microstructure and composition of FeCrAl（f）/HA composites,respectively.The mechanical properties of FeCrAl（f）/HA composites were measured by the three-point-bending test.The results show that the composite can be reinforced by FeCrAl fiber and enhanced gradually,and then declined with the increase of the content of FeCrAl fiber（0-11%,volume fraction） in the whole range of experiments.Both the HA matrix and FeCrAl fiber integrate very tightly and bit into each other very deeply and counter-diffusion takes place to some extent at two-phase interface.The optimum parameters of FeCrAl（f）/HA composite are diameter of 22 μm,length of 1-2 mm and of volume faction of about 7% for FeCrAl fibers.展开更多
This study compares the test results of the FAST (Fabric Assurance by Simple Testing) with those of the KES - F (Kawabata Evaluation Systems for Fabrics) for a range of nineteen light weight wool and wool blend fabric...This study compares the test results of the FAST (Fabric Assurance by Simple Testing) with those of the KES - F (Kawabata Evaluation Systems for Fabrics) for a range of nineteen light weight wool and wool blend fabrics in terms of the low - stress mechanical properties of bending, shear, and tensile deformation. It is found that there are very significant correlations between the corresponding parameters for extensibility and shear rigidity obtained from the test results of the two systems. The correlation between the values of bending rigidity obtained from the two systems is only moderate. Furthermore, for the fabrics tested in this study, the values of bending rigidity, shear rigidity, and extensibility measured using the KES - F instruments are higher than those of the corresponding parameters measured using the FAST instruments. The linear regression equation is given for each pair of corresponding parameter.展开更多
Calcined ginger nuts admixed by fly ash and quartz sand (CGN-(F+S)) has been validated to be basically compatible to earthen sites as an anchor grout. Accelerated ageing tests including water stability test, temperatu...Calcined ginger nuts admixed by fly ash and quartz sand (CGN-(F+S)) has been validated to be basically compatible to earthen sites as an anchor grout. Accelerated ageing tests including water stability test, temperature and humidity cycling test, soundness test and alkali resistance test are conducted with the objective to further research the property changes of CGN-(F+S) grout. Density, surface hardness, water penetration capacity, water permeability capacity, soluble salt, scanning electron microscopy (SEM) images and energy dispersive spectrometry (EDS) spectrum of these samples have been tested after accelerated ageing tests. The results show that densities of samples decrease, surface hardness, water penetration capacity and water permeability capacity of samples increase generally. Besides, soluble salt analysis, SEM and EDS results well corroborate the changes. Based on the results it can be concluded that property changes are most serious after temperature and humidity cycling test, followed by water stability, soundness and alkali resistance test in sequence. But in general, CGN-(F+S) still has good durability.展开更多
This paper uses the generalised gradient approximation based on density functional theory to analyse the geometric structure and properties of the 3d transition metal atom doped endohedral fullerene M@C20F20 （M = Sc...This paper uses the generalised gradient approximation based on density functional theory to analyse the geometric structure and properties of the 3d transition metal atom doped endohedral fullerene M@C20F20 （M = Sc-Ni）. The geometric optimization shows that the cage centre is the most stable position for M, forming the structure named as M@C20F20-4. The inclusion energy, zero-point energy, and energy gap calculations tell us that Ni@C20F20-4 should be thermodynamically and kinetically stablest. M@C20F20-4 （M = Sc-Co） possesses high magnetic moments varied from 1 to 6 μB, while Ni@C20F20-4 is nonmagnetic. The Ni-C bond in Ni@C20F20-4 contains both the covalent and ionic characters.展开更多
The effect of the pyrolytic carbon(PyC)interface thickness on the heat-stability of CansasⅡSiC_(f)/SiC composites under Ar up to 1500℃was studied in detail.After the heat treatment at 1500℃for 50 h,the interface bo...The effect of the pyrolytic carbon(PyC)interface thickness on the heat-stability of CansasⅡSiC_(f)/SiC composites under Ar up to 1500℃was studied in detail.After the heat treatment at 1500℃for 50 h,the interface bonding strength of the thin interface(about 200 nm)decreases from 74.4 to 20.1 MPa(73.0%),while that of the thick interface(about 2μm)declines from 7.3 to 3.2 MPa(52.7%).At the same time,the decline fraction of strength of the composites with the thin interface is 12.1%,less than that with the thick interface(42.0%).The fiber strength also decreases after heat treatment,which may be due to the significant growth ofβ-SiC grains and critical defects.The different heat-stability of the interface with the thin and thick thickness might be related to the inconsistency of the degree of the graphitization of PyC.Compared with the composites with the thick interface,the composites with the thin interface remained higher tensile strength after heat treatment due to the better interface bonding strength.The interface with strong bonding strength could protect the fiber by postponing the decomposition of amorphous phases SiC_(x)O_(y) and hindering the generation of fiber defects.展开更多
The relationship between some smoothness and weak asymptotic-norming properties of dual Banach space X is studied. The main results are the following. Suppose that X is weakly sequential complete Banach space, then X...The relationship between some smoothness and weak asymptotic-norming properties of dual Banach space X is studied. The main results are the following. Suppose that X is weakly sequential complete Banach space, then X is Frechet differentiable if and only if X has B （X）- ANP -I, X is quasi-Frechet differentiable if and only if X has B（X）- ANP -H and X is very smooth if and only if X has B（X）- ANP -Ⅱ. A new local asymptotic-norming property is also introduced, and the relationship among this one and other local asymptotic-norming properties and some topological properties is discussed. In addition, this paper gives a negative answer to the open question raised by Hu and Lin in Bull. Austral. Math. Soc,45,1992.展开更多
Fluorinated amorphous carbon （a-C：F） films were deposited at room temperature using C4Fs and CH4 as precursor gases by electron cyclotron resonance chemical vapour deposition （ECR-CVD）. Chemical structures were a...Fluorinated amorphous carbon （a-C：F） films were deposited at room temperature using C4Fs and CH4 as precursor gases by electron cyclotron resonance chemical vapour deposition （ECR-CVD）. Chemical structures were analysed using X-ray photoelectron spectroscopy （XPS）. The current conduction shows ohmic behaviour and the leakage current increases with the content of C sp2 in the deposited a-C：F films at a low electric field. The behaviour of the leakage current is well e^plained by the Poole-Frankel mechanism at a high electric field. The interface traps, rather than chemical structures, of a-C：F films determine the PF emission current.展开更多
The anodic voltammetric curves of heavily doped n-Si in HF solution, on which three different regions have emerged, and were plotted, A porous silicon layer with fine morphology was formed in linear region.
The conductivity of non-crystalline fast ionic conductor for B_2O_3-Li_2O-LiCl-Al_2O_3 system is studiedin this paper. The glass structure of this system is discussed by means of infrared spectrum and X-ray fluorescen...The conductivity of non-crystalline fast ionic conductor for B_2O_3-Li_2O-LiCl-Al_2O_3 system is studiedin this paper. The glass structure of this system is discussed by means of infrared spectrum and X-ray fluorescence analysis, and the effects of LiCl and A1_2O_3 on the conductivity of Li^+ in the system are studied as well. Adding Li_2O to the system gives rise to transfer from [BO_3] triangular units to [BO_4] tetrahedral. When Li_2O content exceeds 30mol%, the main group of the glass is the diborate group with more [BO_4] tetrahedra. The adding of LiCl has no obvious influence on the glass structure, and LiCl is under a state dissociated by network, but with the increase of LiCl, the increase of conductivity is obvious. By adding A1_2O_3, the glass can be formed when the room-temperature is cooling down,the conductivity decreases while the conductive activatory energy increases for the glass. The experiment shows that conductivity in the room-temperature is σ= 6.2×10^(-6)Ω^(-1)cm^(-1), when at 300℃, the σ=6.8×10^(-3)Ω^(-1)cm^(-1). The conductive activatory energy computed is 0.6～1.0eV.展开更多
The low stress mechanical properties of a pure wool and a wool / polyester blend twill fab-rics which were abraded at various abrasion cycles were measured using the KES-F system andthe Instron tensile machine. The su...The low stress mechanical properties of a pure wool and a wool / polyester blend twill fab-rics which were abraded at various abrasion cycles were measured using the KES-F system andthe Instron tensile machine. The surface change of fabrics before and after abrasion was stu-died by means of scanning electron microscope. With the increasing number of cycles, the re-covery behavior of the fabrics studied in tensile, shear and bending deformation decrease, theantibuckling ability lowers, the friction coefficient increases. The geometric roughness de-creases during the first step of abrasion then enhances with further abrasion. The influence ofabrasion on mechanical properties of the pure wool fabric are larger than that of blend fabric.展开更多
The wool fabrics were treated with low temperature plasma (LTP) using three different gases, namely (ⅰ) oxygen, (ⅱ) nitrogen and (ⅲ) 25％ hydrogen/75％ nitrogen gas mixture. After LTP treatment, the low stress mech...The wool fabrics were treated with low temperature plasma (LTP) using three different gases, namely (ⅰ) oxygen, (ⅱ) nitrogen and (ⅲ) 25％ hydrogen/75％ nitrogen gas mixture. After LTP treatment, the low stress mechanical properties, surface properties and thermal properties of the fabrics were investigated by kES-F (Kawabata Evaluation System) Instruments composing of KES-FBI for tensile and shear property measurement, KES-FB2 for pure bending measurement, kES-FB3 for compression measurement, KES-FB4 for surface friction and surface roughness measurement, and KES-F7 for thermal property measurement. The first four instruments were used for investigating the charaeterlstlc aspect related to fabrle hand while the last one was mainly for the fabric comfort. The properties of LTP treated fabrics under the effect of different gases were compared with the untreated fabric quantitatively.展开更多
基金Project(50774096) supported by the National Natural Science Foundation of ChinaProject(2011QNZT046) supported by the Fundamental Research Funds of the Central South University,ChinaProject supported by the Postdoctoral Science Foundation of Central South University,China
文摘FeCrAl fiber-reinforced hydroxyapatite（HA） biocomposites（FeCrAl（f）/HA） were fabricated by the hot pressing technique.The metallographic microscopy,X-ray diffractometry,scanning electron microscopy（SEM） and energy dispersive spectroscopy（EDS） were used to observe and analyze the microstructure and composition of FeCrAl（f）/HA composites,respectively.The mechanical properties of FeCrAl（f）/HA composites were measured by the three-point-bending test.The results show that the composite can be reinforced by FeCrAl fiber and enhanced gradually,and then declined with the increase of the content of FeCrAl fiber（0-11%,volume fraction） in the whole range of experiments.Both the HA matrix and FeCrAl fiber integrate very tightly and bit into each other very deeply and counter-diffusion takes place to some extent at two-phase interface.The optimum parameters of FeCrAl（f）/HA composite are diameter of 22 μm,length of 1-2 mm and of volume faction of about 7% for FeCrAl fibers.
基金This project was generously funded by International Wool Secretariat
文摘This study compares the test results of the FAST (Fabric Assurance by Simple Testing) with those of the KES - F (Kawabata Evaluation Systems for Fabrics) for a range of nineteen light weight wool and wool blend fabrics in terms of the low - stress mechanical properties of bending, shear, and tensile deformation. It is found that there are very significant correlations between the corresponding parameters for extensibility and shear rigidity obtained from the test results of the two systems. The correlation between the values of bending rigidity obtained from the two systems is only moderate. Furthermore, for the fabrics tested in this study, the values of bending rigidity, shear rigidity, and extensibility measured using the KES - F instruments are higher than those of the corresponding parameters measured using the FAST instruments. The linear regression equation is given for each pair of corresponding parameter.
基金Project(51578272)supported by the National Natural Science Foundation of China
文摘Calcined ginger nuts admixed by fly ash and quartz sand (CGN-(F+S)) has been validated to be basically compatible to earthen sites as an anchor grout. Accelerated ageing tests including water stability test, temperature and humidity cycling test, soundness test and alkali resistance test are conducted with the objective to further research the property changes of CGN-(F+S) grout. Density, surface hardness, water penetration capacity, water permeability capacity, soluble salt, scanning electron microscopy (SEM) images and energy dispersive spectrometry (EDS) spectrum of these samples have been tested after accelerated ageing tests. The results show that densities of samples decrease, surface hardness, water penetration capacity and water permeability capacity of samples increase generally. Besides, soluble salt analysis, SEM and EDS results well corroborate the changes. Based on the results it can be concluded that property changes are most serious after temperature and humidity cycling test, followed by water stability, soundness and alkali resistance test in sequence. But in general, CGN-(F+S) still has good durability.
基金Project supported by the Research Starting Foundation of Hohai University (Grant No. 2084/40801130)the Natural Science Foundation of Hohai University (Grant Nos. 2008431211 and 2008430311)+2 种基金the Excellent Innovation Personal Support Plan of Hohai Universitythe Basic Scientific Research Foundation of National Centralthe Special Foundation of the Natural Natural Science (Grant No. 10947132)
文摘This paper uses the generalised gradient approximation based on density functional theory to analyse the geometric structure and properties of the 3d transition metal atom doped endohedral fullerene M@C20F20 （M = Sc-Ni）. The geometric optimization shows that the cage centre is the most stable position for M, forming the structure named as M@C20F20-4. The inclusion energy, zero-point energy, and energy gap calculations tell us that Ni@C20F20-4 should be thermodynamically and kinetically stablest. M@C20F20-4 （M = Sc-Co） possesses high magnetic moments varied from 1 to 6 μB, while Ni@C20F20-4 is nonmagnetic. The Ni-C bond in Ni@C20F20-4 contains both the covalent and ionic characters.
基金Funded by the National Science and Technology Major Project(No.2017-IV-0005-0042)the China Postdoctoral Science Foundation(No.2021M691566)。
文摘The effect of the pyrolytic carbon(PyC)interface thickness on the heat-stability of CansasⅡSiC_(f)/SiC composites under Ar up to 1500℃was studied in detail.After the heat treatment at 1500℃for 50 h,the interface bonding strength of the thin interface(about 200 nm)decreases from 74.4 to 20.1 MPa(73.0%),while that of the thick interface(about 2μm)declines from 7.3 to 3.2 MPa(52.7%).At the same time,the decline fraction of strength of the composites with the thin interface is 12.1%,less than that with the thick interface(42.0%).The fiber strength also decreases after heat treatment,which may be due to the significant growth ofβ-SiC grains and critical defects.The different heat-stability of the interface with the thin and thick thickness might be related to the inconsistency of the degree of the graphitization of PyC.Compared with the composites with the thick interface,the composites with the thin interface remained higher tensile strength after heat treatment due to the better interface bonding strength.The interface with strong bonding strength could protect the fiber by postponing the decomposition of amorphous phases SiC_(x)O_(y) and hindering the generation of fiber defects.
基金National Natural Science Foundation of China(10671118) the Natural Science Foundation of Shanghai Education Committee (06NZ016)
文摘The relationship between some smoothness and weak asymptotic-norming properties of dual Banach space X is studied. The main results are the following. Suppose that X is weakly sequential complete Banach space, then X is Frechet differentiable if and only if X has B （X）- ANP -I, X is quasi-Frechet differentiable if and only if X has B（X）- ANP -H and X is very smooth if and only if X has B（X）- ANP -Ⅱ. A new local asymptotic-norming property is also introduced, and the relationship among this one and other local asymptotic-norming properties and some topological properties is discussed. In addition, this paper gives a negative answer to the open question raised by Hu and Lin in Bull. Austral. Math. Soc,45,1992.
基金supported by the Key Laboratory Foundation of Electron Devices Reliability Physics and Applications(No.51433020205DZ01)the Xi'an Applied Materials Innovation Fund(No.XA-AM-200501)
文摘Fluorinated amorphous carbon （a-C：F） films were deposited at room temperature using C4Fs and CH4 as precursor gases by electron cyclotron resonance chemical vapour deposition （ECR-CVD）. Chemical structures were analysed using X-ray photoelectron spectroscopy （XPS）. The current conduction shows ohmic behaviour and the leakage current increases with the content of C sp2 in the deposited a-C：F films at a low electric field. The behaviour of the leakage current is well e^plained by the Poole-Frankel mechanism at a high electric field. The interface traps, rather than chemical structures, of a-C：F films determine the PF emission current.
文摘The anodic voltammetric curves of heavily doped n-Si in HF solution, on which three different regions have emerged, and were plotted, A porous silicon layer with fine morphology was formed in linear region.
文摘The conductivity of non-crystalline fast ionic conductor for B_2O_3-Li_2O-LiCl-Al_2O_3 system is studiedin this paper. The glass structure of this system is discussed by means of infrared spectrum and X-ray fluorescence analysis, and the effects of LiCl and A1_2O_3 on the conductivity of Li^+ in the system are studied as well. Adding Li_2O to the system gives rise to transfer from [BO_3] triangular units to [BO_4] tetrahedral. When Li_2O content exceeds 30mol%, the main group of the glass is the diborate group with more [BO_4] tetrahedra. The adding of LiCl has no obvious influence on the glass structure, and LiCl is under a state dissociated by network, but with the increase of LiCl, the increase of conductivity is obvious. By adding A1_2O_3, the glass can be formed when the room-temperature is cooling down,the conductivity decreases while the conductive activatory energy increases for the glass. The experiment shows that conductivity in the room-temperature is σ= 6.2×10^(-6)Ω^(-1)cm^(-1), when at 300℃, the σ=6.8×10^(-3)Ω^(-1)cm^(-1). The conductive activatory energy computed is 0.6～1.0eV.
文摘The low stress mechanical properties of a pure wool and a wool / polyester blend twill fab-rics which were abraded at various abrasion cycles were measured using the KES-F system andthe Instron tensile machine. The surface change of fabrics before and after abrasion was stu-died by means of scanning electron microscope. With the increasing number of cycles, the re-covery behavior of the fabrics studied in tensile, shear and bending deformation decrease, theantibuckling ability lowers, the friction coefficient increases. The geometric roughness de-creases during the first step of abrasion then enhances with further abrasion. The influence ofabrasion on mechanical properties of the pure wool fabric are larger than that of blend fabric.
文摘The wool fabrics were treated with low temperature plasma (LTP) using three different gases, namely (ⅰ) oxygen, (ⅱ) nitrogen and (ⅲ) 25％ hydrogen/75％ nitrogen gas mixture. After LTP treatment, the low stress mechanical properties, surface properties and thermal properties of the fabrics were investigated by kES-F (Kawabata Evaluation System) Instruments composing of KES-FBI for tensile and shear property measurement, KES-FB2 for pure bending measurement, kES-FB3 for compression measurement, KES-FB4 for surface friction and surface roughness measurement, and KES-F7 for thermal property measurement. The first four instruments were used for investigating the charaeterlstlc aspect related to fabrle hand while the last one was mainly for the fabric comfort. The properties of LTP treated fabrics under the effect of different gases were compared with the untreated fabric quantitatively.
