Microstructure and wear mechanisms of OCTG chasers

The wear mechanism and tool life of four types of oil country tubular goods chasers are studied herein via metallographic microscopy,scanning electron microscopy,and energy dispersive spectroscopy.Results show that when the tool has a fine and uniform microstructure,the main failure mode is wear failure.Furthermore,observed phenomena including large chip bonding,coating peeling,cracks demonstrate that the main wear mechanisms of the tool are adhesive wear,abrasive wear,coating flaking,and microchipping.

Effect of Ni content on the wear behavior of Al-Si-Cu-Mg-Ni/SiC particles composites

In recent years,the addition of Ni has been widely acknowledged to be capable of enhancing the mechanical properties of Al-Si alloys.However,the effect of Ni on the wear behaviors of Al-Si alloys and Al matrix composites,particularly at elevated temperat-ures,remains an understudied area.In this study,Al-Si-Cu-Mg-Ni/20wt%SiC particles(SiCp)composites with varying Ni contents were prepared by using a semisolid stir casting method.The effect of Ni content on the dry sliding wear behavior of the prepared compos-ites was investigated through sliding tests at 25 and 350℃.Results indicated that theθ-Al_(2)Cu phase gradually diminished and eventually disappeared as the Ni content increased from 0wt%to 3wt%.This change was accompanied by the formation and increase inδ-Al_(3)CuNi andε-Al_(3)Ni phases in microstructures.The hardness and ultimate tensile strength of the as-cast composites improved,and the wear rates of the composites decreased from 5.29×10^(−4)to 1.94×10^(−4)mm^(3)/(N∙m)at 25℃and from 20.2×10^(−4)to 7×10^(−4)mm^(3)/(N∙m)at 350℃with the increase in Ni content from 0wt%to 2wt%.The enhancement in performance was due to the presence of strengthening network structures and additional Ni-containing phases in the composites.However,the wear rate of the 3Ni composite was approximately two times higher than that of the 2Ni composite due to the fracture and debonding of theε-Al_(3)Ni phase.Abrasive wear,delamination wear,and oxidation wear were the predominant wear mechanisms of the investigated composites at 25℃,whereas delamination wear and oxid-ation wear were dominant during sliding at 350℃.

Intelligent Identification of Wear Mechanism via On-line Ferrograph Images

Condition based maintenance（CBM） issues a new challenge of real-time monitoring for machine health maintenance. Wear state monitoring becomes the bottle-neck of CBM due to the lack of on-line information acquiring means. The wear mechanism judgment with characteristic wear debris has been widely adopted in off-line wear analysis; however, on-line wear mechanism characterization remains a big problem. In this paper, the wear mechanism identification via on-line ferrograph images is studied. To obtain isolated wear debris in an on-line ferrograph image, the deposition mechanism of wear debris in on-line ferrograph sensor is studied. The study result shows wear debris chain is the main morphology due to local magnetic field around the deposited wear debris. Accordingly, an improved sampling route for on-line wear debris deposition is designed with focus on the self-adjustment deposition time. As a result, isolated wear debris can be obtained in an on-line image, which facilitates the feature extraction of characteristic wear debris. By referring to the knowledge of analytical ferrograph, four dimensionless morphological features, including equivalent dimension, length-width ratio, shape factor, and contour fractal dimension of characteristic wear debris are extracted for distinguishing four typical wear mechanisms including normal, cutting, fatigue, and severe sliding wear. Furthermore, a feed-forward neural network is adopted to construct an automatic wear mechanism identification model. By training with the samples from analytical ferrograph, the model might identify some typical characteristic wear debris in an on-line ferrograph image. This paper performs a meaningful exploratory for on-line wear mechanism analysis, and the obtained results will provide a feasible way for on-line wear state monitoring.

Erosive Wear and Wear Mechanism of in situ TiC_P/Fe Composites

The base structure of in situ TiCp/Fe composites fabricated under industrial condition was changed by different heat treatments. Erosive wear tests were carried out and the results were compared with that of wear-resistant white cast iron. The results suggest that the wear resistance of the in situ TiCp/Fe composite is higher than that of wear-resistant white cast iron under the sand erosive wear condition. The wear mechanism of the wear-resistant white cast iron was a cycle process that base surface was worn and carbides were exposed, then carbides was broken and wear pits appeared. While the wear mechanism of in situ TiCp/Fe composite was a cycle process that base surface was worn and TiC grains were exposed and dropped. The wear resistance of in situ TiCp/Fe composite was lower than that of wear-resistant white cast iron under the slurry erosive wear condition. Under such circumstance, the material was not only undergone erosive wear but also electrochemistry erosion due to the contact with water in the medium. The wear behaviours can be a combination of two kinds of wear and the sand erosive wear is worse than slurry erosive wear.

Wear Mechanism of WC-Co Cemented Carbide Tool in Cutting Ti-6Al-4V Based on Thermodynamics

In order to optimize the tool coating material and reduce the tool wear rate,the coating material and wear mechanism for carbide tools are proposed and analyzed based on thermodynamics theory.We deduced the Gibbs free energy function method and analyzed the enthalpy value of the coating material of cemented carbide tools.The rules of diffusion wear and oxidation wear for WC-Co-based carbide tools were analyzed based on the diffusion dissolution theory and the calculation method of the thermal effect of chemical reaction.The diffusion wear and oxidation wear of WC-Co-based carbide tools when machining Ti-6Al-4V were studied with SEM-EDS.The results indicate that a good prediction accuracy of both diffusion wear and oxidation wear can be achieved by the method of thermodynamic theory analysis method.The conclusion will provide useful references for the optimization of cutting parameters and the improvement of the tool life.

WEAR FAILURE MECHANISM AND MULTI-IMPACT PROPERTY OF AUTOMOTIVE ENGINE CHAIN

The multi-impact characteristics and failure mechanism of two kinds of automotive engine chain made in China are studied through engine assembly and road-drive tests. The worn surface morphologies of rubbing area between pin, bush and roller are also analyzed based on scanning electron microscope. The results show that the main wear mechanism of automotive engine chain is fatigue wear, and its failure mechanism is the forming, extending and flaking of cracks on top layer of pin and bush. In addition, the material, hot-treatment method and shaping technique for roller have a great influence upon the resistance to multi-impact. Ensuring sufficient strength and plasticity of roller, as well as adopting suitable shaping technique are the effective method to increase its resistance to multi-impact.

Wear Mechanism of Cemented Carbide Tool in High Speed Milling of Stainless Steel

Adhesion of cutting tool and chip often occurs when machining stainless steels with cemented carbide tools. Wear mechanism of cemented carbide tool in high speed milling of stainless steel 0Cr13Ni4 Mo was studied in this work. Machining tests on high speed milling of 0Cr13Ni4 Mo with a cemented carbide tool are conducted. The cutting force and cutting temperature are measured. The wear pattern is recorded and analyzed by high?speed camera, scanning electron microscope(SEM) and energy dispersive X?ray spectroscopy(EDS). It is found that adhesive wear was the dominant wear pattern causing tool failure. The process and microcosmic mechanism of the tool’s adhesive wear are analyzed and discussed based on the experimental results. It is shown that adhesive wear of the tool occurs due to the wear of coating, the a nity of elements Fe and Co, and the grinding of workpiece materials to the tool material. The process of adhesive wear includes both microcosmic elements di usion and macroscopic cyclic process of adhe?sion, tearing and fracture.

A Review on Fretting Wear Mechanisms,Models and Numerical Analyses

Fretting wear is a material damage in contact surfaces due to micro relative displacement between them.It causes some general problems in industrial applications,such as loosening of fasteners or sticking in components supposed to move relative to each other.Fretting wear is a complicated problem involving material properties of tribosystem and working conditions of them.Due to these various factors,researchers have studied the process of fretting wear by experiments and numerical modelling methods.This paper reviews recent literature on the numerical modelling method of fretting wear.After a briefly introduction on the mechanism of fretting wear,numerical models,which are critical issues for fretting wear modelling,are reviewed.The paper is concluded by highlighting possible research topics for future work.

Abrasive Wear Mechanisms of Sand Particles Intruding into ATM Roller-scraper Tribosystem

The roller-scraper tribosystem of automatic teller machine（ATM） plays an important role in reliable cash requests.However,the abrasive wear of the polymer tribosystem becomes a prominent problem when operating in sandy environment.The wear behavior of the tribosystem in a simulated sandy environment has been experimentally studied previously.However the abrasive wear mechanism of roller-scraper tribosystems is still unknown to new design.The wear rates of polymer rollers were examined comprehensively and several jumping variations were found in the full data extent.Three wear stages were classified by the magnitude of wear rates,and different dominant wear mechanisms corresponding with different particle diameter were found by examining the worn surfaces.Accordingly a presumption was proposed that wear mechanisms in different stages were correlated with sand particles of different diameter.In a verification experiment,three typical wear mechanisms including cutting,ploughing,and wedging were found corresponding with different wear stages by scanning electron microscope（SEM） examination.A theoretical analysis was carried out with a simplified sphere particle intrusion model and the transfer conditions for different wear mechanisms were studied referring to the slip-field theory.As a main result,three typical wear models versus friction coefficient of particle/roller,and particle radius were mapped with variant hardness of the polymer roller and ratio of contact shear stress to bulk shear stress.The result illuminated the abrasive wear mechanism during particle intrusion.Particularly,the critical transition conditions gave the basis for improving the wear performance of roller-scraper tribosystems in a sandy environment.

Analysis of Wear Mechanism and Influence Factors of Drum Segment of Hot Rolling Coiler

Because the work environment of segment is complex, and the wear failures usually happen, the wear mechanism corresponding to the load is a key factor for the solution of this problem. At present, many researchers have investigated the failure of segment, but have not taken into account the compositive influences of matching and coiling process. To investigate the wear failure of the drum segment of the hot rolling coiler, the MMU-5G abrasion tester is applied to simulate the wear behavior under different temperatures, different loads and different stages, and the friction coefficients and wear rates are acquired. Scanning electron microscopy（SEM） is used to observe the micro-morphology of worn surface, X-ray energy dispersive spectroscopy（EDS） is used to analyze the chemical composition of worn surface, finally the wear mechanism of segment in working process is judged and the influence regulars of the environmental factors on the material wear behaviors are found. The test and analysis results show that under certain load, the wear of the segment changes into oxidation wear from abrasive wear step by step with the temperature increases, and the wear degree reduces; under certain temperature, the main wear mechanism of segment changes into spalling wear from abrasive wear with the load increases, and the wear degree slightly increases. The proposed research provides a theoretical foundation and a practical reference for optimizing the wear behavior and extending the working life of segment.

Friction and Wear Mechanism of Unlubricated 304L Austenitic Stainless Steel at Room Temperature

To explore wear mechanism of stainless steel used in nuclear pump, the wear properties and the worn surface characteristics of unlubricated 304L austenitic stainless steel on itself were investigated in air at room temperature. The experimental results demonstrated that the wear rate of the material decreased with the increase of the wear time. The friction coefficient fluctuated severely when the applied load was 120 N. At 120 N the wear rate was much higher than that of the applied load of 70 N. At 70 N the wear rate did not show much difference from that of 30 N. The wear mechanism was adhesive and abrasive wear under different load at the initial stage of the wear test. Then, the main wear mechanism changed with the wearing time and the applied load.

Dry Sliding Friction and Wear Properties and Wear Mechanism of SiC_P/Al Composites

Dry sliding friction and wear properties of A356/SiC composites against AISI D2 were analyzed by means of SEM,XRD and EDS.Results indicated that the wear rate of A356/SiC increased with increase of the applied load.Mild wear took place under lower load,transferring to severe wear at the load heavier than 400 N.Mechanical mixed layer(MML) formed on worn surface during dry sliding friction process,whose thickness became deeper with increasing load.Cracks formed easily in MML and spread transversely,resulting in peeling wear.The wear mechanism of the composite is that oxidation wear mechanism was dominant under low load,with the formation of tiny powdery debris.As the load enhanced,peeling wear was primary due to laminar debris detached from the MML,including oxidation and adhesive wear at the same time,with the load at 350-450 N,adhesive wear with irregular debris and peeling wear were predominant.

Discussion on Wear Mechanism of High Chrome Brick Used in Coal Slurry Gasifier

The microstructure and phase composition of high chrome brick used in coal slurry gasifier has been analyzed by means of SEM and Energy Spectrum. The results indicate that the used brick can be divided into different zones as slag-adhered zone, reaction zone, penetration zone and unaltered zone. The phase composition and microstructure are different and cracks occurred in different degree at these zones. A dense ring belt was formed with complex spinel (Mg,Fe)(Cr,Al,Fe 2O 4) in the reaction zone near the hot face. The wear mechanism of the brick during its employment has been discussed. It is considered that the reaction and penetration of coal slag and strong reductant bring about the composition change of the brick and destroys its original network inlayed structure and consequently result in its structure spalling and weakening strength, which is the main wear mechanism of the brick and followed by temperature fluctuation and high mechanical impact of flowing fluid with high-speed.

Characteristics and mechanism of abrasive wear for thermoplastic polymers

Abrasive wear characteristics of polyethylene, polystyrene,polymethylmethacrylate, nylon 1010 and polyvinyl chloride were investigated. The volume relativewear resistance coefficients of these thermoplastic polymers are 18%-35% (hardened and lowtemperature tempered steel 45 was used as a comparing material), and have a linear correlation withsquare roots of their cohesive energy densities. The coefficients of linear correlation is 0.949.Wear morphologies were observed by scanning electron microscope (SEM). Main wear mechanism of thethermoplastic polymers includes brittle breaking for the hard and brittle polymers & plowing andfatiguing for the soft and tough ones.

Corrosion and wear properties of in situ(TiB+TiC)/TA15 composites with a high volume percentage of reinforcement

The in situ(TiC+TiB)/TA15 composites with different volume percentages of reinforcement(10%,15%,20%and 25%)were prepared by water-cooled copper crucible vacuum suspension melting technology.The structures and compositions of the TA15 alloy and its composites were analyzed by XRD and EDS,and their electrochemical corrosion behaviors in the 3.5%NaCl solution were studied.Corrosion wear testing was conducted using a reciprocating ball-on-disc wear tester under a 10 N load.Results show that the in situ fibrous TiB phase and the granular TiC phase are uniformly distributed on the composite matrix.The microhardness can reach up to 531 HV as 25vol.%TiC+TiB reinforcement is added.Compared with the TA15 alloy,the volume wear rate decreases from(2.21±0.07)×10^(-4)to(1.75±0.07)×10^(-4)mm^(3)·N^(-1)·m^(-1)by adding 15vol.%TiC+TiB reinforcement,and the wear mechanism is adhesive wear.When the volume percentage of the reinforcement phase reaches 25%,the volume wear rate increases from(1.75±0.07)×10^(-4)to(2.41±0.07)×10^(-4)mm^(3)·N^(-1)·m^(-1),and the wear mechanism changes into abrasive wear.The volume loss resulted by the interaction between corrosion and wear accounts for more than 27%of the total wear volume.The volume loss due to wear-induced corrosion changes from 1.94%to 4.06%with different additions of reinforcement.The volume loss caused by corrosion-induced wear initially increases from 24.08%to 26.90%as the reinforcement increases from 0 to 15%due to the increase of corrosion potential,and then decreases from 26.90%to 25.68%as the reinforcement increases from 15%to 25%due to the peeling of TiC phase.

Experimental Study on Wear and Spalling Behaviors of Railway Wheel

The current researches of the wear and spalling behaviors of wheel/rail materials focus on the field investigation rather than the mechanism. However, it is necessary and significant for clarifying the mechanism and relationship between the wear and spalling damage of railway wheel to test and reproduce the wheel damages in laboratory. The objective of this paper is to investigate the wear and spalling damage behaviors of railway wheel using a JD-1 wheel/rail simulation facility, which consists of a small wheel serving as rolling stock wheel, and a larger wheel serving as rail. The damage process of wheel roller is explored in terms of the creep ratio, axle load, and carbon content by means of various microscopic examinations. The experimental results show that the wear volume growth of wheel roller is proved to be proportional to the increase of the creep ratio and normal load between simulating wheel and rail. The increase of carbon content of wheel material causes a linear reduction in the wear volume. The microscopic examinations indicate that the rolling wear mechanism transfers from abrasive wear to adhesive and fatigue wear with an increase of tangential friction force, which results in the initiation of fatigue crack, and then aggravates spalling damage on the wheel roller surface. The surface hardness of material depends strongly upon its carbon content. The decrease of the carbon content of wheel material may alleviate spalling damage, but can cause a significant growth in the wear volume of wheel roller. Therefore, there is a competitive relationship between the wear and spalling damage of wheel material. This research proposes an important measure for alleviating or preventing the wear and spalling damage of railway wheel material.

Polygonisation of railway wheels:a critical review

Polygonisation is a common nonuniform wear phenomenon occurring in railway vehicle wheels and has a severe impact on the vehicle–track system,ride comfort,and lineside residents.This paper first summarizes periodic defects of the wheels,including wheel polygonisation and wheel corrugation,occurring in railways worldwide.Thereafter,the effects of wheel polygonisation on the wheel–rail interaction,noise and vibration,and fatigue failure of the vehicle and track components are reviewed.Based on the different causes,the formation mechanisms of periodic wheel defects are classified into three categories:(1)initial defects of wheels,(2)natural vibration of the vehicle–track system,and(3)thermoelastic instability.In addition,the simulation methods of wheel polygonisation evolution and countermeasures to mitigate wheel polygonisation are presented.Emphasis is given to the characteristics,effects,causes,and solutions of wheel polygonisation in metro vehicles,locomotives,and highspeed trains in China.Finally,the guidance is provided on further understanding the formation mechanisms,monitoring technology,and maintenance criterion of wheel polygonisation.

Experimental study ofcasing wear under impact-sliding conditions

Theoretical analysis and field monitoring show that lateral vibration has very important effect on casing wear in deep & ultra-deep well drilling. The wear mechanism of casing under impact-sliding work conditions has been investigated and many experiments have been completed with a newly developed full-scale casing wear test machine. Test results present that adhesion wear, contact fatigue, and grinding abrasion are the main wear mechanisms under impact-sliding test conditions. The friction coefficient and linear wear rate of the casing rise obviously with an increase in impact load. And the larger the impact load, the rougher the worn surface of the casing. The linear wear rate decreased slightly but the average friction coefficient increased slightly with an increase in impact frequency under an impact load of 2,500 N. Both the linear wear rate of the casing and the average friction coefficient increased substantially with an increase in impact frequency under an impact load of 4,000 N. Under lower impact load conditions, grinding abrasion and contact fatigue are the main mechanisms of casing wear; under higher impact load conditions, adhesion wear and contact fatigue are the main mechanisms of casing wear.

Dry sliding wear behavior of an extruded Mg-Dy-Zn alloy with long period stacking ordered phase

The dry sliding wear behavior of extruded Mg-2Dy-0.5Zn alloy(at.%)was investigated using a pin-on-disk configuration.The friction coefficient and wear rate were measured within a load range 20-760 N at a sliding velocity of 0.785 m/s.Microstructure and wear surface of alloy were examined using scanning electron microscopy.The mechanical properties of alloy were tested at room and elevated temperatures.Five wear mechanisms,namely abrasion,oxidation,delamination,thermal softening and melting dominated the whole wear behavior with increasing applied load.The extruded Mg-2Dy-0.5Zn alloy exhibited the better wear resistance as compared with as-cast Mg_(97)Zn_(1)Y_(2) alloy under the given conditions through contact surface temperature analysis.The improved wear resistance was mainly related to fine grain size,good thermal stability of long period stacking order(LPSO)phase and excellent higher-temperature mechanical properties.

Tribological Performance of Bioimplants: A Comprehensive Review

Total joint replacements(TJR) have been a huge success for orthopaedic surgery in the past century and are gaining increasing importance today due to the aging population. However, the short longevity of artificial joints is one of the major problems in bioimplant industry and needs to be rectified since an increasing number of young people, with more active lifestyles, must receive TJR. Wear mechanisms are discussed in this paper to describe the root causes of the failures and to give some general ideas to increase the lifespan of artificial joints. The suitable material combination is of great importance for the wear resistance of bioimplants, and bioceramics will exert a crucial effect in their future progress. Other materials, such as metal alloys and polymers, are also discussed in this paper. Surface finish is another factor affecting the tribological performance of bioimplants. In recent years, surface texture technology has fascinated many researchers, and a good design of texture pattern requires a comprehensive understanding of wear mechanisms, material properties, and dynamic fluid theory. This review also covers a summary of in vitro wear tests, including simulators, lubricant, and testing parameters.