Catalytic wet oxidation of aniline over Ru catalysts supported on a modified TiO_2

The catalytic wet air oxidation of aniline over Ru catalysts supported on modified Ti 2 （Ti 2, Ti0.9Ce0.1O2, Ti0.9Zr0.1O2） is investigated. A series of characterization techniques are conducted to determine the relationship between the physico-chemical properties and the catalytic performance. As a result of the good metal dispersion and large number of surface oxygen species, the Ru/Ti0.9 Zr0.1O2 catalyst presents the best catalytic activity among the tested samples. The effects of the operating conditions on the reaction are investigated and the optimal reaction conditions are determined. Based on the relationship between the by-products concentration and the reaction time, the reaction path for the catalytic oxidation of aniline is established. Carbonaceous deposits on the surface of the support are known to be the main reason for catalyst deactivation. The catalysts maintain a constant activity even after three consecutive cycles.

Wet Oxidation of Al_x Ga_(1-x)As/GaAs Distributed Bragg Reflectors

The wet oxidation of AlGaAs with high Al content in a distributed Bragg reflectors （DBR） is studied by scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. Some voids distribute along the oxide/GaAs interfaces due to the stress induced by the wet oxidation of the AlGaAs layers. These voids decrease the shrinkage of the Al2O3 layers to 8% instead of the theoretical 20% when compared to the unoxidized AlGaAs layers. With the extension of oxidation time, the reactants are more completely transported to the front interface and the products are more completely transported out along the porous interfaces. As a result,the oxide quality is better.

Study on Catalytic Wet Oxidation of H_2S into Sulfur on Fe/Cu Catalyst

A wet catalytic oxidation at room temperature was investigated with solution containing ferric, ferrous and cupric ions for H2S removal. The experiments were carried out in a two step process, and the results obtained show that the removal efficiency of H2S can always reach 100% in a 300 mm scrubbing column with four sieve plates, and the regeneration of ferric ions in 200 mm bubble column can match the consumed ferric species in absorption. Removal of H2S, production of elemental sulfur and regeneration of ferric, cupric ions can all be accomplished at the same time. No raw material is consumed except O2 in flue gas or air, the process has no secondary pollution and no problem of catalyst degradation and congestion.

Study on Industrial Application of Hydrogen Sulfide Removal by Wet Oxidation Method with High Gravity Technology

The removal of hydrogen sulfide from gas plays an important role in rational utilization of resources and environ- mental protection. In this paper, the process of hydrogen sulfide removal by wet oxidation method in a rotating packed bed was investigated in a scale for treating 10 000 Nm3/h of gas. On the basis of studying the influence of the species and con- centration of alkali source, the liquid/gas volume ratio, the high gravity factor, and the hydrogen sulfide content in feed gas on the desulfurization effect, the suitable technological conditions were obtained. The hydrogen sulfide removal efficiency could reach 98.0% under these conditions. The results of continuous operation of process facilities showed that the high gravity method has many merits including higher desulfurization rate, good stability in operation, lower liquid/gas volume ratio, greater operation elasticity, and apparent energy saving effects.

Wet Oxidation of PVA-Containing Desizing Wastewater

Polyvinyl alcohol (PVA)-containing desizing wastewater was treated by various wet oxidation methods.Parameters such as reaction temperature, initial solution pH, and the dosage of H2O2 were investigated in terms of chemical oxygen demand (CODcr) and total organic carbon (TOC) removal rate. Up to 90% of the initial CODcr was removed by wet air oxidation(WAO) at 270℃ with stoichiometric oxygen supply, while at temperature of 200℃, the CODcr removal rate was found to be 80%. Similar results were obtained by Promoted WAO (PWAO) and wet peroxide oxidation(WPO) at a lower temperature of 150℃. Reaction temperature was found to have a significant effect on the oxidation performance for all the methods. Initial solution pH was observed to play a significant role in PWAO and WPO where H2O2 was employed. Comparison of WAO, CWAO(catalytic wet air oxidation), PWAO and WPO shows that the rate of CODcr removal increases in the order: WAO, CWAO, PWAO and WPO.

Wet Oxidation Pretreatment of Poplar Waste for Enhancing Enzymatic Hydrolysis Efficiency

In this paper, we described the optimization of the wet oxidation pretreatment conditions to enhance enzymatic hydrolysis efficiency, using poplar waste from the stock section of a paper mill as the raw material. We showed that the optimal conditions of the pretreatment for poplar waste were an initial p H value of 10, a temperature of 195℃, a holding time of 15 min, and an oxygen pressure of 1.2 MPa. In this case, the yield of the obtained solid material produced by the process was 51.7% and the reducing sugar yield was 46.8%. The solid part obtained from the pretreatment process was hydrolyzed by cellulase L-10. The optimal enzymatic conditions were a temperature of 49℃, a duration time of 56 h, an enzyme dosage of 38 FPU/g at a p H value of 4.8, and a solid-to-liquor ratio of 1∶50. The resulting cellulose conversion rate reached 96.4% in terms of the pretreated substances. In addition, a chemical composition analysis of the poplar waste and pretreated material indicated that about 92% of the hemicelluloses and 43% of the lignin in the raw material were degraded and dissolved. In addition, the crystallization decreased from 57.5% to 54.8%. An obvious fibrillation of the fiber pretreated by the wet oxidization process was observed by SEM. Moreover, high-performance liquid chromatography(HPLC) results showed a high xylose content and monosaccharide degradation products in the pretreatment solution. In conclusion, the wet oxidation pretreatment process could efficiently degrade or remove the lignin and hemicellulose, as well as reduce the crystallinity of the lignocellulosic material, which resulted in animprovement of the enzymatic ability and an increase in the cellulose conversion rate.

Resting Study of Tracer Experiment on Catalytic Wet Oxidation Reactor under Micro-gravity and Earth Gravity Conditions

The International Space Station（ISS） employs catalytic wet oxidation carried out in a Volatile Reactor Assembly （VRA） for water recycling. Previous earth gravity experiments show that the VRA is very effective at removing polar, low molecular weight organics. To compare the reactor performance under micro-gravity and Earth gravity conditions, a tracer study was performed on a space shuttle in 1999 by using 0.2% potassium carbonate as the chemical tracer. In this paper, the experimental data were analyzed and it is indicated that the reactor can be considered as a plug flow one under both micro-gravity and earth gravity experimental conditions. It has also been proved that dispersion is not important in the VRA reactor under the experimental conditions. Tracer retardation was observed in the experiments and it is most likely caused by catalyst adsorption. It is concluded that the following reasons may also have influence on the retardation of mean residence time ： （1） the liquid can be held by appurtenances, which will retard the mean residence time; （2） the pores can hold the tracer, which can also retard the mean residence time.

Fe salts as catalyst for the wet oxidation of o-chlorophenol

Catalytic wet air oxidation (CWAO) of o-chlorophenol in wastewater was studied in a stainless steel autoclave using four different Fe catalysts in the temperature range of 100?200 °C. Experimental results showed that high rate of o-chlorophenol and CODCr (Chemical Oxygen Demand, mg/L) removal by CWAO was obtained at relatively low temperature and pressure. The catalysts Fe2(SO4)3, FeSO4, Fe2O3 and FeCl3 all exhibited high catalytic activity. More than 93.7% of the initial CODCr and nearly 100% of o-chlorophenol were removed at 150 °C after 150 min with FeSO4 as catalyst. The CWAO of o-chlorophenol was found to be pseudo-first order reaction with respect to o-chlorophenol, with activation energy of 75.56 kJ/mol in the temperature range of 100-175 °C.

Preparation of PrFe_(x)Co_(1-x)O_(3)/Mt catalyst and study on degradation of 2-hydroxybenzoic acid wastewater by catalytic wet peroxide oxidation

In this study,the perovskite nanocomposite PrFe_(x)Co_(1-x)O_(3)(Pr(S))was successfully synthesized by the sol-gel method;PrFe_(x)Co_(1-x)O_(3)/Al-pillared montmorillonite(Pr(S)/Mt)catalysts were prepared by impregnation(D)method and solid-melting(G)method,respectively,with Pr(S)as the active component and Al-pillared montmorillonite as the carrier.The catalysts were applied to treat the 2-hydroxybenzoic acid(2-HA)-simulated wastewater by catalytic wet peroxide oxidation(CWPO)technique,and the chemical oxygen demand(COD)removal rate and the 2-HA degradation rate were used as indicators to evaluate the catalytic performance.The results of the experiment indicated that the solid-melting method was more conducive to preparing the catalyst when the Co/Fe molar ratio of 7:3 and the optimal structural properties of the catalysts were achieved.The influence of operating parameters,including reaction temperature,catalyst dosage,H_(2)O_(2)dosage,pH,and initial 2-HA concentration,were optimized for the degradation of 2-HA by CWPO.The results showed that 97.64%of 2-HA degradation and 75.23%of COD removal rate were achieved under more suitable experimental conditions.In addition,after the catalyst was used five times,the degradation rate of 2-HA could still reach 76.93%,which implied the high stability and reusability of the catalyst.The high catalytic activity of the catalyst was due to the doping of Co into PrFeO_(3),which could promote the generation of HO·,and the high stability could be attributed to the loading of Pr(S)onto Al-Mt,which reduced the leaching of reactive metals.The study of reaction mechanism and kinetics showed that the whole degradation process conformed to the pseudo-firstorder kinetic equation,and the Langmuir-Hinshelwood method was applied to demonstrate that catalysis was dominant in the degradation process.

Microwave assisted wet oxidation of p-nitrophenol

Aqueous solution of p-nitrophenol(PNP)was treated continuously by microwave assisted wet oxidation while flowing through a granular activated carbon(GAC)fixed bed.PNP was pre-adsorbed onto GAC prior to being put into the reactor so as to prevent PNP adsorption on GAC during microwave irradiation.PNP solutions with different initial concentration(218.6 mg/L and 1200 mg/L)were treated under conditions of microwave power 500 W,liquid flow 6.4 mL/min and air flow 40 mL/min or 60 mL/min.The results indicated that the removal of PNP was higher than 90%and more than 65%PNP was mineralized.Phenol,nitrobenzene,hydroquinone and benzoquinone occurred as course products during the operation process,which were degraded further.The biodegradability of the outflow was improved greatly by microwave assisted wet oxidation.

Characterization of value-added chemicals derived from the thermal hydrolysis and wet oxidation of sewage sludge

We evaluated the effect of hydrothermal pretreatments,i.e.,thermal hydrolysis(TH)and wet oxidation(WO)on sewage sludge to promote resource recovery.The hydrothermal processes were performed under mild temperature conditions(140°C–180°C)in a high pressure reactor.The reaction in acidic environment(pH=3.3)suppressed the formation of the color imparting undesirable Maillard’s compounds.The oxidative conditions resulted in higher volatile suspended solids(VSS)reduction(~90%)and chemical oxygen demand(COD)removal(~55%)whereas TH caused VSS and COD removals of~65%and~27%,respectively at a temperature of 180°C.During TH,the concentrations of carbohydrates and proteins in treated sludge were 400–1000 mg/L and 1500–2500 mg/L,respectively.Whereas,WO resulted in solids solubilization followed by oxidative degradation of organics into smaller molecular weight carboxylic acids such as acetic acid(~400–500 mg/L).Based on sludge transformation products generated during the hydrothermal pretreatments,simplified reaction pathways are predicted.Finally,the application of macromolecules(such as proteins),VFAs and nutrients present in the treated sludge are also discussed.The future study should focus on the development of economic recovery methods for various value-added compounds.

Investigation on preparation of CuO-SnO_2-CeO_2/γ-Al_2O_3 catalysts for catalytic wet air oxidation process and their catalytic activity for degradation of phenol

Catalytic Wet Air Oxidation process is an efficient measure for treatment of wastewater with great strength which is not biodegradable. Heterocatalysts now become the key investigation subject of catalytic wet air oxidation process due to their good stability and easy separation. In the paper, CuO-SnO2-CeOγ-Al2O3 catalysts are prepared by impregnation method, with SnO2 as a doping component, CuO as an active component, CeO2 as a structure stabilizer, γ-Al2O3 as a substrate. XPS test is carried out to investigate the effect of Sn on the chemical surrounding of Cu and O element on the catalyst surface and their catalytic activity. It is shown that the right doping of Sn can increase Cu^＋ content on the catalyst surface, as a result the quantity of adsorption oxygen is also increased. It is found that Cu^＋ content on the catalyst surface is one of the primary factors that determin catalytic activity of catalyst through analyzing the catalytic wet air oxidation process of phenol.

Protection effect of a SiO_2 layer in Al_(0.85)Ga_(0.15)As wet oxidation

The Al0.85Ga0.15As layers buried below the GaAs core layer with and without the SiO2 layer were successfully oxidized in a wet ambient environment.The experimental results show that the SiO2 layer has little impact on the lateral-wet-oxidation rate of the Al0.85Ga0.15 As layer.The contrast of the SEM image of the oxidized regions and the absence of As-related Raman peaks for samples with the SiO2 layer arise from the removal of As ingredients with the largest atomic number,which leads to improvements in the thermal stability of the oxidized layer.The PL intensities of samples with the SiO2 layer are much stronger than those without the SiO2 layer.The PL emission peak is almost unshifted with a slight broadening under the protection of the SiO2 layer.This is attributed to the SiO2 layer preventing oxidation damage to the GaAs capping layer.

Degradation of H-acid in aqueous solution by microwave assisted wet air oxidation using Ni-loaded GAC as catalyst

A novel process, microwave assisted catalytic wet air oxidation(MW-CWO), was applied for the degradation of H-acid(1-amino-8-naphthol-3, 6-disulfonic acid) in aqueous solution. Ni-loaded granular activated carbon(GAC), prepared by immersion-calcination method, was used as catalyst. The results showed that the MW-CWO process was very effective for the degradation of H-acid in aqueous solution under atmospheric pressure with 87.4% TOC (total organic carbon) reduction in 20 min. Ni on GAC existed in the form of NiO as specified by XRD. Loss of Ni was significant in the initial stage, and then remained almost constant after 20 min reaction. BET surface area results showed that the surface property of GAC after MW-CWO process was superior to that of blank GAC.

Application of Catalytic Wet Air Oxidation to Treatment of Landfill Leachate on Co/Bi Catalyst

Catalytic wet air oxidation(CWAO) was employed to reduce the organic compounds in landfill leachate and the effects of temperature, oxygen pressure, catalyst dosage, and concentration of the organic compounds on the TOC and COD Cr removal rates were studied. The degradation kinetics of landfill leachate was also investigated and an exponential experiential model consisting of four influential factors was established to describe the reduction of the organic compounds in the landfill leachate. Meanwhile, the GC-MS technique was used to detect the components of the organic intermediates for the inference of the decomposition mechanisms of the organic compounds in landfill leachate. The results reveal that the reaction temperature and the catalyst dosage are the most important factors affecting the degradation reaction of the organic compounds and that the principal intermediates confirmed by GC-MS are organic acids at a percentage of more than 88% with no aldehydes or alcohols detected. The decomposition mechanisms of the organic compounds in landfill leachate were inferred based on the GC-MS information as follows: the activated gas phase O 2 captured the hydrogen of the organic pollutants to produce free radicals, which then initiated the catalytic reaction. So most of the organic compounds were oxidized into CO 2 and H 2O ultimately. In general, catalytic wet air oxidation over catalyst Co 3O 4/Bi 2O 3 was a very promising technique for the treatment of landfill leachate.

Catalytic wet air oxidation of phenol over RuO_2/γ-Al_2O_3 catalyst

A kind of CWAO catalyst, RuO_2/γ-Al_2O_3, was prepared by dipping Al_2O_3into the aqueous solution of RuCl_3·3H_2O. XRD, SEM and TEM were used to determine the catalyticstructure. Influences of the calcination temperature, the initial pH of the feed solution anddegradation temperature on the activity of the RuO_2/γ-Al_2O_3 catalyst were investigated and thereaction mechanism was preliminarily studied. Results showed that uniform dispersion of RuO_2crystallites was observed on the surface of the catalyst. The activity of the catalyst was higher atcalcination temperature of 300℃ for 3 h and the particle reunion occurred and some large RuO_2crystallites were abundant at high calcination temperature of 500℃ The activity of the catalyst wasbetter in the acid solution than in the alkaline solution. Increasing degradation temperature andusing the catalyst could shorten the induction periods so that the phenol and COD removal wereincreased. For RuO_2/γ-Al_2O_3 catalyst, the phenol and COD removal were respectively 98% and 80%in a temperature of 150℃, pH of 5.6 and pressure of 3 MPa after a 2 h reaction. This indicated thatRu/γ-Al_2O_3 catalyst had good activity.

A highly hydrothermal stable copper-based catalyst for catalytic wet air oxidation of m-cresol in coal chemical wastewater

Catalytic wet air oxidation(CWAO) can degrade some refractory pollutants at a low cost to improve the biodegradability of wastewater. However, in the presence of high temperature and high pressure and strong oxidizing free radicals, the stability of catalysts is often insufficient, which has become a bottleneck in the application of CWAO. In this paper, a copper-based catalyst with excellent hydrothermal stability was designed and prepared. TiO_(2) with excellent stability was used as the carrier to ensure the longterm anchoring of copper and reduce the leaching of the catalyst. The one pot sol–gel method was used to ensure the super dispersion and uniform distribution of copper nanoparticles on the carrier, so as to ensure that more active centers could be retained in a longer period. Experiments show that the catalyst prepared by this method has good stability and catalytic activity, and the catalytic effect is not significantly reduced after 10 cycles of use. The oxidation degradation experiment of m-cresol with the strongest biological toxicity and the most difficult to degrade in coal chemical wastewater was carried out with this catalyst. The results showed that under the conditions of 140℃, 2 MPa and 2 h, m-cresol with a concentration of up to 1000 mg·L^(-1) could be completely degraded, and the COD removal rate could reach 79.15%. The biological toxicity of wastewater was significantly reduced. The development of the catalyst system has greatly improved the feasibility of CWAO in the treatment of refractory wastewater such as coal chemical wastewater.

Catalytic Wet Air Oxidation of oChlorophenol in Wastewater

Catalytic wet air oxidation (CWAO) was investigated in laboratory-scale experiments for the treatment of o-chlorophenol in wastewater. Experimental results showed that wet air oxidation (WAO) process in the absence of catalyst was also effective for o-chlorophenol in wastewater treatment. Up to 80% of the initial CODCr was removed by wet air oxidation at 270℃ with twice amount of the required stoichiometric oxygen supply. At temperature of 150℃, the removal rate of CODCr was only 30%. Fe2(SO4)3, CuSO4, Cu(NO3)2 and MnSO4 exhibited high catalytic activity. Higher removal rate of CODCr was obtained by CWAO. More than 96% of the initial CODCr was removed at 270℃ and 84.6%-93.6% of the initial CODCr was removed at 150℃. Mixed catalysts had better catalytic activity for the degradation of o-chlorophenol in wastewater.

Structure, characterization, and dynamic performance of a wet air oxidation catalyst Cu–Fe–La/γ-Al_2O_3

A Cu–Fe–La/γ-Al_2O_3(CFLA) catalyst was prepared by the excessive impregnation method and characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The results indicate that the catalyst contained mostly Cu^(2+), Fe^(3+), and La^(3+)and a small amount of Cu^+, Fe^(2+), and La. The active components were uniformly distributed in the catalyst, and the particle size of the components was approximately 7.5 nm. The CFLA catalyst was used for the treatment of methyl orange(MO) solution by catalytic wet air oxidation(CWAO), and it exhibited a high catalytic activity. The catalytic reaction involved variable valence states of metals and free-radical reaction mechanism. The CWAO reaction of MO solution was fitted by a segmented first-order dynamic model, and the rapid reaction apparent activation energy was 13.9 k J·mol^(-1).

Kinetics study on catalytic wet air oxidation of phenol by several metal oxide catalysts

Four metal oxide catalysts composed of copper(Cu), stannum(Sn), copper-stannum(Cu-Sn) and copper-cerium(Cu-Ce) respectively were prepared by the co-impregnation method, and γ-alumina(γ-Al 2O 3) is selected as support. A first-order kinetics model was established to study the catalytic wet air oxidation of phenol at different temperature when these catalysts were used. The model simulations are good agreement with present experimental data. Results showed that the reaction rate constants can be significantly increased when catalysts were used, and the catalyst of 6% Cu—10%Ce/γ-Al 2O 3 showed the best catalytic activity. This is consistent with the result of catalytic wet air oxidation of phenol and the COD removal can be arrived at 98.2% at temperature 210℃, oxygen partial pressure 3 MPa and reaction time 30 min. The activation energies of each reaction with different catalysts are nearly equal, which is found to be about 42 kJ/mol and the reaction in this study is proved to be kinetics control.