Flexible Optical Waveguide Bent Loss Attenuation Effects Analysis and Modeling Application to an Intrinsic Optical Fiber Temperature Sensor

The temperature dependence of the bending loss light energy in multimode optical fibers is reported and analyzed. The work described in this paper aims to extend an initial previous analysis concerning planar optical waveguides, light energy loss, to circular optical waveguides. The paper also presents à novel intrinsic fiber optic sensing device base on this study allowing to measure temperatures parameters. The simulation results are validated theoretically in the case of silica/silicone optical fiber. A comparison is done between results obtained with an optical fiber and the results obtained from the previous curved optical planar waveguide study. It is showed that the bending losses and the temperature measurement range depend on the curvature radius of an optical fiber or waveguide and the kind of the optical waveguide on which the sensing process is implemented.

Temperature sensor based on a single-mode tapered optical fiber

A temperature sensor is demonstrated and fabricated by coating the single-mode tapered optical fiber with temperature-sensitive silicone rubber. It works on the change of the evanescent fields in the tapered optical fiber. Small changes in the refractive index of coating film greatly influence the power of evanescent fields, which modulate the transmission optical power in the waist region. The range of temperature measured is from -20℃ to 70 ℃. The results show that the temperature sensor has high temperature sensitivity （0.012 mW/℃） and good repeatability.

Highly sensitive optical fiber temperature sensor based on resonance in sidewall of liquid-filled silica capillary tube

A highly sensitive optical fiber temperature sensor based on a section of liquid-filled silica capillary tube(SCT)between single mode fibers is proposed. Two micro-holes are drilled on two sides of SCT directly by using femtosecond laser micromachining, and liquid polymer is filled into the SCT through the micro-holes without any air bubbles and then sealed by using ultra-violet(UV) cure adhesive. The sidewall of the SCT forms a Fabry–Perot resonator, and loss peaks are achieved in the transmission spectrum of the SCT at the resonant wavelength. The resonance condition can be influenced by the refractive index variation of the liquid polymer filled in SCT, which is sensitive to temperature due to its high thermooptical coefficient(-2.98 × 10^-4℃^-1). The experimental result shows that the temperature sensitivity of the proposed fiber structure reaches 5.09 nm/℃ with a perfect linearity of 99.8%. In addition, it exhibits good repeatability and reliability in temperature sensing application.

Novel Fiber Optic Temperature Sensor with Full Compensation Based on Optical Absorption

A novel system configuration of fiber optic sensor based on optical abso rption is proposed. Several compensation measures are discussed. A simulated exp eriment is designed and the output curve of system is given. The experiment al result shows that these compensation measures are effective on dynamic distu rbances which are caused by background light and optical fiber bend. In addition , the drifts in the light source intensity, fiber losses, and photodetector effi ciency are also compensated.

Bismuth and Erbium Co-doped Optical Fiber for a White Light Fiber Source

We demonstrate a white light fiber source based on Bismuth and Erbium co-doped fiber and a single 830nm laser diode pump. The light spectral intensity from 1100 to 1570nm is over -45dBm, which provide ~40dB dynamic range for an OSA based spectral measurement.

Network Integration of Distributed Optical Fiber Temperature Sensor

The integration of distributed optical fiber temperature sensor with supervisory control and data acquisition （SCADA） system is proposed and implemented. In the implementation of the integration, both the compatibility with traditional system and the characteristics of distributed optical fiber temperature sensor is considered before Modbus TCP/IP protocol is chosen. The protocol is implemented with open source component Indy. The Modbus TCP/IP protocol used in the system is proved to be fast and robust.

Combined optical fiber interferometric sensors for the detection of acoustic emission

A type of combined optical fiber interferometric acoustic emission sensor is proposed. The sensor can be independent on the laser source and make light interference by matching the lengths of two arms,so it can be used to monitor the health of large structure. Theoretical analyses indicate that the system can be equivalent to the Michelson interferometer with two optical fiber loop reflectors,and its sensitivity has been remarkably increased because of the decrease of the losses of light energy. PZT is powered by DC regulator to control the operating point of the system,so the system can accurately detect feeble vibration which is generated by ultrasonic waves propagating on the surface of solid. The amplitude and the frequency of feeble vibration signal are obtained by detecting the output light intensity of interferometer and using Fourier transform technique. The results indicate that the system can be used to detect the acoustic emission signals by the frequency characteristics.

Temperature and Salinity Dual-parameter Sensing Based on Forward Brillouin Scattering in 1060-XP SMF

A novel temperature and salinity discriminative sensing method based on forward Brillouin scattering(FBS)in 1060-XP single-mode fiber(SMF)is proposed.The measured frequency shifts corresponding to different radial acoustic modes in 1060-XP SMF show different sensitivities to temperature and salinity.Based on the new phenomenon that different radial acoustic modes have different frequency shift-temperature and frequency shift-salinity coefficients,we propose a novel method for simultaneously measuring temperature and salinity by measuring the frequency shift changes of two FBS scattering peaks.In a proof-of-concept experiment,the temperature and salinity measurement errors are 0.12℃and 0.29%,respectively.The proposed method for simultaneously measuring temperature and salinity has the potential applications such as ocean surveying,food manufacturing and pharmaceutical engineering.

All-Fiber Optic Temperature Sensor

This paper presents a new class of all fiber optic temperature sensor, of which the heat expansion thin film is coated on the etched fiber. The sensitivity of the sensor is increased and the shape size is decreased. This sensor possesses the linear temperature response and the good repeatability. These sensors can be used to measure finely the temperature that is lower than 200℃ with aluminium coating.

Temperature dependence of the refractive index of optical fibers

Many experimental investigations on the temperature dependence of the refractive index of optical fibers have been reported previously, however a satisfying theoretical explanation for it is still absent. In this paper, a theoretical model about the temperature dependence of the refractive index of optical fibers is presented and it is in agreement with the previous experimental results. This work is a significant reference for the research and development of temperature sensors based on optical fiber delay lines.

Stabilization of Intensity- based Optical Fiber Pressure Sensor

A practical optical fiber differential pressure sensor is presented at first. Then the techniques of light source feedback, set up of reference channel, proportional measurement and other methods to improve the stability of the system as well as to reduce the interference with same nature are emphatically discussed. Finally, the experiment results of the developed instrument are given.

Mathematical Model of Fiber Optic Temperature Sensor Based on Optic Absorption and Experiment Testing

On the basis of analysis on the temperature monitoring methods for high voltage devices, a new type of fiber optic sensor structure with reference channel is given. And the operation principle of fiber optic sensor is analysed at large based on the absorption of semiconductor chip. The mathematical model of both devices and the whole system are also given. It is proved by the experiment that this mathematical model is reliable.

Reflective Ladder Topology Network Based on White Light Fiber-Optic Mach-Zehnder Interferometer

In order to improve the multiplexing capability of the optical sensors based on the lower interferential optic fiber sensing technology and the white light fiber-optic Mach-Zehnder interferometer,reflective ladder topology network ( RLT) with tailored formula was proposed. The topology network consists of 6 rungs sensing elements linked by 5 couplers. Two cases with different choices of couplers were contrasted: one is equal coupling ratio,and the other is tailored coupling ratio. Through the simulation of these two cases,the detailed multiplexing capability was analyzed,and accordingly the experiments were also carried out. The simulation results showed that,the tailored formula enhances the multiplexing capability of the structure. In the first case, the maximum number of sensors which can be multiplexed is 8,and in the other case is 12 fiber optic sensors. The experimental results have a good agreement with numerical simulation results. Thus,it is considered expedient to incorporate RLT into large-scale building,grounds,bridges,dams,tunnels,highways and perimeter security.

Fiber Optic Fourier Transform White-Light Interferometry

Fiber optic Fourier transform white-light inter-fereometry is presented to interrogate the absolute optical path difference of an Maeh-Zehnder interferometer. The phase change of the interferometer caused by scanning wavelength can be calculated by a Fourier transform-based phase demodulation technique. A linear output is achieved.

FIBER OPTIC TEMPERATURE MEASURING SYSTEM

This paper presents a fiber optic temperature measuring system used for measuring the temperature in many occasions. The system is of reflective type and composed of thermostatic bimetal plate, lever piston framework, optical grating and optical fiber probes. When the temperature changes, the thermostatic bimetal plate deforms. Through lever piston framework, the optical grating produces displacement in the upright direction. Thus the change of the temperature is transformed into the upright displacement of the optical grating. Optical fiber probes are used for detecting the number of streak lines of the optical grating′s displacement depending on the change of temperature. The detected signal can be transmitted to the control center through optical fiber cable up to distance of 1 km. The measurable range of this system reaches 100℃ with accuracy of ±0.2℃.

Fiber optic strain twin-sensor-array for smart structural health monitoring

A multiplexed white light interferometric fiber optic twin-sensor-array was designed to monitor the structural health of large buildings.In this sensing system,based on a Michelson interferometer,an optical path matching technique is used to demodulate each twin-sensor.Each twin-sensor-array consists of a 2×N sensing element linked by a 3 dB coupler.When one of the twin-sensor is used to measure strain,variations caused by temperature can be compensated for by referencing the other twin-sensor.The multiplexing capacity of the sensing scheme has been analyzed and experimental results with a 2×3 twin-sensor-array are given.

Absolute Measurement Fiber-optic Sensors inLarge Structural Monitoring

The security of civil engineering is an important task due to the economic, social and environmental significance. Compared with conventional sensors, the optical fiber sensors have their unique characteristics.Being durable, stable and insensitive to external perturbations,they are particular interesting for the long-term monitoring of civil structures.Focus is on absolute measurement optical fiber sensors, which are emerging from the monitoring large structural, including SOFO system, F-P optical fiber sensors, and fiber Bragg grating sensors. The principle, characteristic and application of these three kinds of optical fiber sensors are described together with their future prospects.

Fabry-Perot Temperature Sensor for Quasi-Distributed Measurement Utilizing OTDR

A quasi-distributed Fabry-Perot fiber optic temperature sensor array using optical time domain reflectometry （OTDR） technique is presented. The F-P sensor is made by two face to face single-mode optical fibers and their surfaces have been polished. Due to the low reflectivity of the fiber surfaces, the sensor is described as low Fresnel Fabry-Perot interferometer （FPI）. The working principle is analyzed using twobeam optical interference approximation. To measure the temperature, a certain temperature sensitive material is filled in the cavity. The slight changes of the reflective intensity which is induced by the refractive index of the material was caught by OTDR. The length of the cavity is obtained by monitoring the interference spectrum which is used for the setting of the sensor static characteristics within the quasi-linear range. Based on our design, a three point sensor array are fabricated and characterized. The experimental results show that with the temperature increasing from -30℃ to 80℃, the reflectivity increase in a good linear manner. The sensitivity was approximate 0.074 dB℃. For the low transmission loss, more sensors can be integrated.

光纤光栅温度应力传感教学实验装置

针对目前市场上可直接用于光纤光栅传感实验教学的装置较少,前沿科研技术和本科实验教学相脱节现状,设计了基于光纤光栅的温度应力传感教学装置。该装置包括光纤激光器、光谱仪和上位机控制软件3部分。光纤激光器实现了1 550 nm左右的激光输出,利用光谱仪测量光纤光栅中心波长的改变,并采集数据输入计算机,上位机控制软件用于图形显示和数据存储等。该实验装置操作简单、组装灵活、重复性和稳定性好,可用于本科实验教学。将前沿科学技术引入本科实验教学,促进了科学研究与本科实验教学相融合,实现了科研教学水平的同步提高。

精准温度控制半导体激光治疗仪及其可靠性分析

目的探究影响基于保偏光纤温度传感器的半导体激光治疗仪功率稳定输出的关键因素,探索实用化的激光治疗系统光电子器件可靠性分析方法。方法基于可靠性框图法,对系统光电子器件及其外围电路建立可靠度(RSL)、失效率(λSL)和平均寿命(LSL)分析模型,分析使用环境、运行时间(t)和工作温度(T)对系统运行可靠性的影响。基于加速寿命模型分别在室温大驱动电流(T=25℃、I=2.5 A)、高温工作电流(T=50℃、I=1.5 A)和高温大驱动电流(T=50℃、I=2.5 A)条件下,测试LSL与T、I以及T和I相互作用条件下的关系。结果仿真结果表明,λSL随T的增加而增加,LSL随T的增加而降低,RSL随T和t的增加而降低,在I为1.5 A、T为50℃的条件下,λSL、LSL、RSL估计值分别为5.229×10-51/h、17824.500 h、0.11418。实验结果显示,LSL分别为22873、17693和4780 h,实验测试结果与仿真结果吻合。结论基于本研究所提方法,可结合系统架构、设计方法、使用环境,分析计算出设备的λSL是否满足使用规范,进而预测出设备的RSL与LSL,为设计制造与临床使用提供数据支撑。