Wideband spectrum sensing using step-sampling based on the multipath nyquist folding receiver

Wideband spectrum sensing with a high-speed analog-digital converter(ADC) presents a challenge for practical systems.The Nyquist folding receiver(NYFR) is a promising scheme for achieving cost-effective real-time spectrum sensing,which is subject to the complexity of processing the modulated outputs.In this case,a multipath NYFR architecture with a step-sampling rate for the different paths is proposed.The different numbers of digital channels for each path are designed based on the Chinese remainder theorem(CRT).Then,the detectable frequency range is divided into multiple frequency grids,and the Nyquist zone(NZ) of the input can be obtained by sensing these grids.Thus,high-precision parameter estimation is performed by utilizing the NYFR characteristics.Compared with the existing methods,the scheme proposed in this paper overcomes the challenge of NZ estimation,information damage,many computations,low accuracy,and high false alarm probability.Comparative simulation experiments verify the effectiveness of the proposed architecture in this paper.

5G Wideband Bandpass Filtering Power Amplifiers Based on a Bandwidth-Extended Bandpass Matching Network

In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined as a variable in the closedform equations provided by the microstrip bandpass filter.It can be extended over a wide range only by changing the characteristic impedances of the structure.Different from the other wideband MNs,the extension of bandwidth does not increase the complexity of the structure(order n is fixed).In addition,based on the bandwidth-extended structure,the wideband design of bandpass filtering PA is not limited to the fixed bandwidth of the specific filter structure.The theoretical analysis of the MN and the design flow of the PA are provided in this design.The fabricated bandpass filtering PA can support almost one-octave bandwidth(2-3.8 GHz),covering the two 5G bands(n41 and n78).The drain efficiency of 47%-60%and output power higher than 40 dBm are measured.Good frequency selectivity in S-parameter measurements can be observed.

Robust dual-channel correlation algorithm for complex weak target detection with wideband radar

In the scene of wideband radar,due to the spread of target scattering points,the attitude and angle of view of the target constantly change in the process of moving.It is difficult to predict,and the actual echo of multiple scattered points is not fully matched with the transmitted signal.Therefore,it is challenging for the traditional matching filter method to achieve a complete matching effect in wideband echo detection.In addition,the energy dispersion of complex target echoes is still a problem in radar target detection under broadband conditions.Therefore,this paper proposes a wideband target detection method based on dualchannel correlation processing of range-extended targets.This method fully uses the spatial distribution characteristics of target scattering points of echo signal and the matching characteristics of the dual-channel point extension function itself.The radial accumulation of wideband target echo signal in the complex domain is realized through the adaptive correlation processing of a dual-channel echo signal.The accu-mulation effect of high matching degree is achieved to improve the detection probability and the performance of wideband detection.Finally,electromagnetic simulation experiments and measured data verify that the proposed method has the advan-tages of high signal to noise ratio(SNR)gain and high detection probability under low SNR conditions.

A True-Time-Delay Array Architecture for Wideband Multi-Beam Tracking

The true-time delay(TTD)units are critical for solving beam squint and frequency selective fading inWideband Large-Scale Antenna Systems(LSASs).In this work,we propose a TTD array architecture for wideband multi-beam tracking that eliminates the beam squint phenomenon and filters out interference signals by applying a spatial filter and time delay estimations(TDEs).The paper presents a novel approach to spatial filter design by introducing a transformation matrix that can optimize the beam response in a specific direction and at a specific frequency.Using the variable fractional delay(VFD)filters,we propose a TDE algorithm with a Newton-Raphson iteration update process that corrects the arrival time delay difference between sensors.Simulations and examples have demonstrated that the proposed architecture can achieve beam tracking within 10 ms at the low signalto-noise ratio(SNR)and demodulation loss is less than 0.5 dB in wideband multi-beam scenarios.

MODIFIED ULTRA WIDEBAND CIRCULAR PRINTED MONOPOLE ANTENNA

A simple and compact microstrip-fed ultra wideband （UWB） printed monopole antenna is presented. The antenna is composed of a circular radiator and a finitely grounded plane. The antenna occupies about 16.62 GHz absolute bandwidth and 142.7% relative bandwidth covering from 3.38 GHz to 20 GHz with voltage standing wave ratio （VSWR） below two. A quasi-omnidirectional and quasi-symmetrical radiation pattern in H plane is obtained in the whole bandwidth. The high performance of the antenna is validated with measured and simulated results given. The antenna can be applied for the system design of UWB wireless communication.

A4~12GHz Wideband Balanced MIC Power Amplifier

A 4-12GHz wideband power amplifier,using a balanced configuration with a strip line Lange coupler, is designed and fabricated. This power amplifier shows a maximum continuous wave output power of 29.5dBm at 8GHz center frequency with an associated gain of 8.5dB and a gain flatness of ＋ /- 0.6dB in the 4-12GHz frequency range.

Wideband CMOS LC VCO design and phase noise analysis

A wideband LC cross-coupled voltage controlled oscillator（VCO） is designed and realized with standard 0. 18 μm complementary metal-oxide-semiconductor（CMOS） technology. Band switching capacitors are adopted to extend the frequency tuning range, and the phase noise is optimized in the design procedure. The functional relationships between the phase noise and the transistors＇ width-length ratios are deduced by a linear time variant （LTV） model. The theoretical optimized parameter value ranges are determined. To simplify the calculation, the working region is split into several sub-ranges according to transistor working conditions. Thus, a lot of integrations are avoided, and the phase noise function upon the design variables can be expressed as simple proportion formats. Test results show that the DC current is 8.8 mA under a voltage supply of 1.8 V; the frequency range is 1.17 to 1.90 GHz, and the phase noise reaches - 83 dBc/Hz at a 10 kHz offset from the carrier. The chip size is 1. 2 mm × 0. 9 mm.

An Ultra Wideband VHF CMOS LC VCO

This paper presents a VHF CMOS VCO. The most significant improvement on the VCO is that the cross-coupled MOSFET pairs are divided into several switchable parts so the characteristics can compensate the state change that results from the frequency tuning of the oscillator. This VCO is implemented in 0, 18μm CMOS with a core area of about 550μm × 700μm. The test results show that the tuning range covers 31-111MHz with a power consumption between 0.3-6. 9mW and a phase noise at a 100kHz offset of about - 110dBc/Hz.

Wideband Signal Detection Based on MWC Discrete Compressed Sampling Structure

In order to solve the cross-channel signal problem caused by the uniform channelized wideband digital receiver when processing wideband signal and the problem that the sensitivity of the system greatly decreases when the bandwidth of wideband digital receiver increases,which both decrease the wideband radar signal detection performance,a new wideband digital receiver based on the modulated wideband converter(MWC)discrete compressed sampling structure and an energy detection method based on the new receiver are proposed.Firstly,the proposed receiver utilizes periodic pseudo-random sequences to mix wideband signals with baseband and other sub-bands.Then the mixed signals are low-pass filtered and downsampled to obtain the baseband compressed sampling data,which can increase the sensitivity of the system.Meanwhile,the cross-channel signal will all appear in any subbands,so the cross-channel signal problem can be solved easily by processing the baseband compressed sampling data.Secondly,we establish the signal detection model and formulate the criterion of the energy detection method.And we directly utilize the baseband compressed sampling data to carry out signal detection without signal reconstruction,which decreases the complexity of the algorithm and reduces the computational burden.Finally,simulation experiments demonstrate the effectiveness of the proposed receiver and show that the proposed signal detection method is effective in low signal-to-noise ratio(SNR)compared with the conventional energy detection and the probability of detection increases significantly when SNR increases.

Progress in ultra-wideband planar antennas

This paper introduces the advances of ultra-wideband （UWB） and super-wideband （SWB） planar antennas based on the printed monopole, microstrip slot and other planar antenna designs in the last decade. A brief history of the ultrawideband antennas is first provided. Several types of planar antennas for UWB systems with band-notched designs are reviewed. Special SWB planar antenna designs with the bandwidth ratio greater than 10：1 including metal-plate and printed monopole antennas and tapered slot antennas are presented and compared.

A wideband low-phase-noise LC VCO for DRM/DAB frequency synthesizer

The wideband CMOS voltage-controlled oscillator（VCO）with low phase noise and low power consumption is presented for a DRM/DAB（digital radio mondiale and digital audio broadcasting）frequency synthesizer.In order to obtain a wide band and a large tuning range,a parallel switched capacitor bank is added in the LC tank.The proposed VCO is implemented in SMIC 0.18-μm RF CMOS technology and the chip area is 750 μm×560 μm,including the test buffer circuit and the pads.Measured results show that the tuning range is 44.6%;i.e.,the frequency turning range is from 2.27 to 3.57 GHz.The measured phase noise is-122.22 dBc/Hz at a 1 MHz offset from the carrier.The maximum power consumption of the core part is 6.16 mW at a 1.8 V power supply.

Ultra-wideband bilateral tapered slot-line antenna fed by coplanar waveguide

In order to broaden the bandwidth of a tapered slot- line antenna （TSA）, a bilateral tapered slot-line antenna （BTSA） with a new feeding structure of coplanar waveguide （CPW） is developed. Based on the fact that the bandwidth limitation of TSA mainly depends on its feeding structure, an improved CPW-based feed structure etched on the backboard of the BTSA is adopted to perform traveling-wave transition. Both the simulation results and measurement data verify that the proposed feeding structure results in ＂high-pass＂ frequency response for antenna impedance matching. The voltage standing wave ratio （VSWR） is less than 2：1 when the frequency is higher than 3 GHz. The antenna gain exceeds 7 dBi with good radiation patterns when the bandwidth is from 4 to 16 GHz. This ultra wideband （UWB） antenna with a compact size is specially available for the electronic systems of counter-measure and microwave imaging.

Frame erasure concealment in wideband speech coding based on large hidden Markov model

Frame erasure concealment is studied to solve the problem of rapid speech quality reduction due to the loss of speech parameters during speech transmission. A large hidden Markov model is applied to model the immittance spectral frequency （ISF） parameters in AMR-WB codec to optimally estimate the lost ISFs based on the minimum mean square error （MMSE） rule. The estimated ISFs are weighted with the ones of their previous neighbors to smooth the speech, resulting in the actual concealed ISF vectors. They are used instead of the lost ISFs in the speech synthesis on the receiver. Comparison is made between the speech concealed by this algorithm and by Annex I of G. 722. 2 specification, and simulation shows that the proposed concealment algorithm can lead to better performance in terms of frequency-weighted spectral distortion and signal-to-noise ratio compared to the baseline method, with an increase of 2.41 dB in signal-to-noise ratio （SNR） and a reduction of 0. 885 dB in frequency-weighted spectral distortion.

A wideband metamaterial absorber based on a magnetic resonator loaded with lumped resistors

A wideband metamaterial absorber （MA） based on a magnetic resonator loaded with lumped resistors is presented. It is composed of a one-dimensional periodic array of double U-shaped structured magnetic resonators loaded with lumped resistors, a dielectric substrate, and a metal plate. We simulated, fabricated, measured, and analyzed the MA. The experimental results show that the reflectance （S11） is below -10 dB at normal incidence in the frequency range of 7.7 GHz 18 GHz, and the peak value is about -20 dB. Simulated power loss density distributions indicate that wideband absorption of the MA is mainly attributable to the lumped resistors in the magnetic resonator. Further investigations indicate that the distance between two unit cells along the magnetic field direction significantly influences the performance of the MA.

New direction of arrival estimation method for wideband coherent signals

To estimate the direction-of-arrival （DOA） of wideband coherent signals, a new method by modifying the orthogonality of the projected suhspaces method is proposed. And it can deal with randomly position perturbed arrays by using the Toeplitz method. This method needn＇t the primary information of DOA for focusing matrix and the sector dividing of interpolated method, which improving the precision of estimation and reducing the computational complexity. Simulations illustrate the effectiveness of this method.

Compact ultra-wideband monopole antenna with dual-band notched function

A kind of compact ultra wideband （UWB） monopole antenna with dual-band notched function is presented.The proposed antenna,using ＂C＂ and ＂L＂ apertures embedded in the annular ring patch and ground patch,gets two bandnotched characteristics in WiMAX3.5 GHz and WLAN 5.5 GHz.The size of antenna is 24 mm × 36 mm × 1.6 mm.The simulation results show that waveband range of the antenna is 2.7-10.6 GHz for S11 ＜-10 dB and the band-notched wavebands are 3.2-3.8 GHz and 5.1-6 GHz.So it has miniaturization,ultra-band and band-notched characteristics.Meanwhile,the radition pattern,directivety and gain are perfect,which meets the practical need.

DOA estimation of wideband signals based on iterative spectral reconstruction

In order to solve the problem of coherent signal subspace method(CSSM) depending on the estimated accuracy of signal subspace, a new direction of arrival(DOA) estimation method of wideband source, which is based on iterative adaptive spectral reconstruction, is proposed. Firstly, the wideband signals are divided into several narrowband signals of different frequency bins by discrete Fourier transformation(DFT). Then, the signal matched power spectrum in referenced frequency bins is computed, which can form the initial covariance matrix. Finally, the linear restrained minimum variance spectral(Capon spectral) of signals in other frequency bins are reconstructed using sequential iterative means, so the DOA can be estimated by the locations of spectral peaks. Theoretical analysis and simulation results show the proposed method based on the iterative spectral reconstruction for the covariance matrices of all sub-bands can avoid the problem of determining the signal subspace accurately with the coherent signal subspace method under the conditions of small samples and low signal to noise ratio(SNR), and it can also realize full dimensional focusing of different sub-band data, which can be applied to coherent sources and can significantly improve the accuracy of DOA estimation.

Wideband angle of arrival estimation of chirp signals using virtual Wignerville distribution

To estimate the angle of arrivals （AOA） of wideband chirp sources, a new timo-frequency algorithm is proposed. In this method, virtual sensors are constructed based on the fact that the steering vectors of wideband chirp signals are linear and vary with time. And the randon Wignersville distribution （RWVD） of real sensors and virtual sensors are calculated to yield the new time-invariable steering vectors, furthermore, the noise and cross terms are suppressed. In addition, the multiple chirp signals are selected by their time-frequency points. The cost of computation is lower than the common AOA estimation methods of wideband sources due to nonrequirement of frequency focusing, interpolating and matrix decomposition, including subspace decomposition. Under the lower signal noise ratio （SNR） condition, the proposed method exhibits better precision than the method of frequency focusing （FF）. The proposed method can be further applied to nonuniform linear array （NLA） since it is not confined to the array geometry. Simulation results illustrate the efficacy of the proposed method.

Approach for wideband direction-of-arrival estimation in the presence of array model errors

The presence of array imperfection and mutual coupling in sensor arrays poses several challenges for development of effective algorithms for the direction-of-arrival （DOA） estimation problem in array processing. A correlation domain wideband DOA estimation algorithm without array calibration is proposed, to deal with these array model errors, using the arbitrary antenna array of omnidirectional elements. By using the matrix operators that have the memory and oblivion characteristics, this algorithm can separate the incident signals effectively. Compared with other typical wideband DOA estimation algorithms based on the subspace theory, this algorithm can get robust DOA estimation with regard to position error, gain-phase error, and mutual coupling, by utilizing a relaxation technique based on signal separation. The signal separation category and the robustness of this algorithm to the array model errors are analyzed and proved. The validity and robustness of this algorithm, in the presence of array model errors, are confirmed by theoretical analysis and simulation results.

Wideband mid-infrared thermal emitter based on stacked nanocavity metasurfaces

Efficient thermal radiation in the mid-infrared(M-IR)region is of supreme importance for many applications including thermal imaging and sensing,thermal infrared light sources,infrared spectroscopy,emissivity coatings,and camouflage.The ability to control light makes metasurfaces an attractive platform for infrared applications.Recently,different metamaterials have been proposed to achieve high thermal radiation.To date,broadening the radiation bandwidth of a metasurface emitter(meta-emitter)has become a key goal to enable extensive applications.We experimentally demonstrate a broadband M-IR thermal emitter using stacked nanocavity metasurface consisting of two pairs of circular-shaped dielectric(Si;N;)–metal(Au)stacks.A high thermal radiation can be obtained by engineering the geometry of nanocavity metasurfaces.Such a meta-emitter provides wideband and broad angular absorptance of both p-and s-polarized light,offering a wideband thermal radiation with an average emissivity of more than 80%in the M-IR atmospheric window of 8–14μm.The experimental illustration together with the theoretical framework establishes a basis for designing broadband thermal emitters,which,as anticipated,will initiate a promising avenue to M-IR sources.