Thermal expansion of kyanite at ambient pressure:An X-ray powder diffraction study up to 1000℃

The thermal expansion coefficients of kyanite at ambient pressure have been investigated by an X-ray powder diffraction technique with temperatures up to 1000 ℃. No phase transition was observed in the experimental temperature range. Data for the unit-cell parameters and temperatures were fitted empirically resulting in the following thermal expansion coefficients： αa = 5.8（3） × 10^-5, αb = 5.8 （1）× 10^-5, αc = 5.2（1）× 10^-5, and αv = 7.4（1） × 10^-3 ℃ 1 in good agreement with a recent neutron powder diffraction study. On the other hand, the variation of the unit-cell angles α, β and γ of kyanite with increase in temperature is very complicated, and the agreement among all studies is poor. The thermal expansion data at ambient pressure reported here and the compression data at ambient temperature from the literature suggest that, for the kyanite lattice, the most and least thermally expandable directions correspond to the most and least compressible directions, respectively.

Ab initio Structure Determination of [Co(NH_3)_5Br]Br_2 Using Conventional X-ray Powder Diffraction

The crystal structure of [Co(NH3)5Br]Br2 has been determined ab initio from the conventional X-ray powder diffraction data. The approximate structure with all 7 indeyendent non-H atoms was solved by direct methods. The final orthorhombic unit-cell parameters after Rietveld refinement are: a=13.6927, b=10.7071, c=6.9400A, V=1017.47A3, F30=93(0.0075,43), M20=49, Z=4. Space group is Pnma. The structure agreement factors are: Rp=0.066,Rwp=0.090, RF=0.041, RB=0.042.

Neutron powder diffraction and high-pressure synchrotron x-ray diffraction study of tantalum nitrides

Tantalum nitride （TAN） compact with a Vickers hardness of 26 GPa is prepared by a high-pressure and high- temperature （HPHT） method. The crystal structure and atom occupations of WC-type TaN have been investigated by neutron powder diffraction, and the compressibility of WC-type TaN has been investigated by using in-situ high-pressure synchrotron x-ray diffraction. The third-order Birch-Murnaghan equation of state fitted to the x-ray diffraction pressure- volume （P-V） sets of data, collected up to 41 GPa, yields ambient pressure isothermal bulk moduli of B0 = 369（2） GPa with pressure derivatives of B~ = 4 for the WC-type TaN. The bulk modulus of WC-type TaN is not in good agreement with the previous result （Bo = 351 GPa）, which is close to the recent theoretical calculation result （Bo = 378 GPa）. An analysis of the experiment results shows that crystal structure of WC-type TaN can be viewed as alternate stacking of Ta and N layers along the c direction, and the covalent Ta-N bonds between Ta and N layers along the c axis in the crystal structure play an important role in the incompressibility and hardness of WC-type TaN.

Rietveld Refinement and X-ray Powder Diffraction Data of GdAlSi

The X-ray powder diffraction data of the compound GdAlSi was studied by means of X-ray diffraction technique and refined by Rietveld method. The compound GdAlSi has tetragonal α-ThSi_2-type structure, space group I4_1/amd (No.141), Z=4, the lattice parameters a=041234 (1) nm, c=1.44202(1) nm. The Smith and Snyder figure of merit [5] F_N is F_ 30=2521(36). The R-factors of Rietveld refinement are R_p=0.098 and R_ wp=0.128. The X-ray powder diffraction data are given. The field dependence of the magnetization measured at room temperature and the temperature variation of the inverse magnetic susceptibility of the compound GdAlSi were also presented.

X-ray Powder Diffraction Data and Rietveld Refinement for NdCoGe_3

オ-ray powder diffraction data and crystal structure of RE compound NdCoGe3 were studied by using X-ray powder diffraction and refined by the Rietveld profile fitting method. The compound has the tetragonal BaNiSn3type structure, space group I4mm (No.107) a=0.42961(2) nm, c=098147(4) nm, V=0.018114 nm3, Z=2 and Dx=7.717 g·cm-3. The figure of merit FN for the powder data is F30=623 (0.0107, 45). Structure refinement was performed with 110 reflections and led to Rp=11.78% and Rwp=16.56%.

X-ray Powder Diffraction Pattern of Bi_4(SiO_4)_3

In cooperation with figure-of-merits the Rietveld analysis can appraise both angular and intensity data of powder diffraction. In this work, X-ray diffraction pattern of Bi4(SiO4)3 was redetermined with intensity figure-of-merits, which qualify agreement between observed and calculated relative intensities. F30 is 158.90 (0.0059, 32), intensity figure of merit Rint is 8.7, I20(17), 8.0. The values of figure-of-merits show that the data of JCPDS cards are distorted. Both the experimental and calculated peak positions and heights are listed in detail.

IDENTIFICATION AND SIMULATION OF X-RAY POWDER DIFFRACTION PATTERN

A new method for pattern identification and simulation of X-ray powder diffraction data is described, which can give definite phase composition of the unknown rapidly and correctly. The method is implemented in Microsoft Fortran 77 for the IBM PC/XT/AT personal computer or their compatibles.

MY RESEARCH ACHIEVEMENTS IN POWDER X-RAY DIFFRACTION & PHASE DIAGRAMS

I graduated from the Department of Chemistry, Xiamen University in 1955, majoring in physical chemistry. I went to the Institute of Metallurgy under the Soviet Academy of Sciences in 1956 as a Ph.D.candidate in thermochemistry and crystal chemistry of metal alloys,and got my Ph.D.degree in 1960.In the following 30 years, I did basic and applied research in interdisciplines,including crystal chemistry,materials science and solid state physics.My main achievements can be listed in two aspects as follows:

Characterization of Average Molecular Structure of Heavy Oil Fractions by ~1H Nuclear Magnetic Resonance and X-ray Diffraction

The chemical structure of heavy oil fractions obtained by liquid-solid adsorption chromatography was character-ized by 1 H nuclear magnetic resonance and X-ray diffraction.The molecular weight and molecular formula of asphaltene molecules were estimated by combining 1 H nuclear magnetic resonance and X-ray diffraction analyses,and were also ob-tained from vapor pressure osmometry and elemental analysis.Heteroatoms,such as S,N,and O atoms,were considered in the construction of average molecular structure of heavy oils.Two important structural parameters were proposed,including the number of alkyl chain substituents to aromatic rings and the number of total rings with heteroatoms.Ultimately,the av-erage molecular structures of polycyclic aromatics,heavy resins and asphaltene molecules were constructed.The number of α-,β-,γ-,and aromatic hydrogen atoms of the constructed average molecular structures fits well with the number of hydro-gen atoms derived from the experimental spectral data.

Fitting Full X-Ray Diffraction Patterns for Quantitative Analysis: A Method for Readily Quantifying Crystalline and Disordered Phases

Fitting of full X-ray diffraction patterns is an effective method for quantifying abundances during X-ray diffraction (XRD) analyses. The method is based on the principal that the observed diffraction pattern is the sum of the individual phases that compose the sample. By adding an internal standard (usually corundum) to both the observed patterns and to those for individual pure phases (standards), all patterns can all be normalized to an equivalent intensity based on the internal standard intensity. Using least-squares refinement, the individual phase proportions are varied until an optimal match is reached. As the fitting of full patterns uses the entire pattern, including background, disordered and amorphous phases are explicitly considered as individual phases, with their individual intensity profiles or “amorphous humps” included in the refinement. The method can be applied not only to samples that contain well-ordered materials, but it is particularly well suited for samples containing amorphous and/or disordered materials. In cases with extremely disordered materials where no crystal structure is available for Rietveld refinement or there is no unique intensity area that can be measured for a traditional RIR analysis, full-pattern fitting may be the best or only way to readily obtain quantitative results. This approach is also applicable in cases where there are several coexisting highly disordered phases. As all phases are considered as discrete individual components, abundances are not constrained to sum to 100%.

X-Ray Diffraction, Electron Paramagnetic Resonance and Optical Absorption Study of Bauxite

The bauxite mineral obtained from Araku, Vishakapatnam district of Andhra Pradesh, India is used in the present work. Structural characterization was performed by X-ray diffraction (XRD). The mineral was found to be gibbsite in phase. The transitional metal ions present were investigated using electron paramagnetic resonance (EPR) and optical absorption spectra. The EPR results suggest that Fe3+ has replaced Al3+ in the unit cell of bauxite. The optical absorption spectrum is due to Fe3+ which indicates that it is in distorted octahedral environment. The near-infrared (NIR) spectrum is due to water fundamentals and combination overtones, which confirm the formula of the compound. The impurities in the mineral are identified using spectroscopic techniques.

Crystallographic Characteristic of Intermetallic Compounds in Al-Si-Mg Casting Alloys Using Electron Backscatter Diffraction

The Al-Si-Mg alloy which can be strengthened by heat treatment is widely applied to the key components of aerospace and aeronautics. Iron-rich intermetallic compounds are well known to be strongly influential on mechanical properties in Al-Si-Mg alloys. But intermetallic compounds in cast Al-Si-Mg alloy intermetallics are often misidentified in previous metallurgical studies. It was described as many different compounds, such as AlFeSi, Al8Fe2Si, Al5（Fe, Mn）3Si2 and so on. For the purpose of solving this problem, the intermetallic compounds in cast Al-Si alloys containing 0.5% Mg were investigated in this study. The iron-rich compounds in Al-Si-Mg casting alloys were characterized by optical microscope（OM）, scanning electron microscope（SEM）, energy dispersive X-ray spectrometer（EDS）, electron backscatter diffraction（EBSD） and X-ray powder diffraction（XRD）. The electron backscatter diffraction patterns were used to assess the crystallographic characteristics of intermetallic compounds. The compound which contains Fe/Mg-rich particles with coarse morphologies was Al8FeMg3Si6 in the alloy by using EBSD. The compound belongs to hexagonal system, space group P6_2m, with the lattice parameter a=0.662 nm, c=0.792 nm. The β-phase is indexed as tetragonal Al3FeSi2, space group I4/mcm, a=0.607 nm and c=0.950 nm. The XRD data indicate that Al8FeMg3Si6 and Al3FeSi2 are present in the microstructure of Al-7Si-Mg alloy, which confirms the identification result of EBSD. The present study identified the iron-rich compound in Al-Si-Mg alloy, which provides a reliable method to identify the intermetallic compounds in short time in Al-Si-Mg alloy. Study results are helpful for identification of complex compounds in alloys.

SYNTHESIS AND X-RAY POWDER STUDY OF A NEW COMPOUND:Ba_6Ti_7Nb_9O_(42)

A new compound Ba6Ti7Nb9O42 was prepared for the first time by solid state reaction in BaO-TiO2-Nb2O5, ternary system. The X-ray powder diffraction data of the title compound was determined. Ba6Ti7Nb9O42 crystallizes in the hexagonal system -with unit cell parameters a=9.0527(4) A,c=11.790(1) A,and space group P63/mcm(193),z=1. The calculated and measured densities are 5. 293 g/cm3 and 5.285 g/cm3, respectively.

大黄游离羟基蒽醌的TG-DTA和XRD谱图特征分析

Objective,Used the TG/DTA curves and XRD patterns to identify five kinds of free anthraquinones.Method,The thermograms,differential thermograms and X-ray powder diffraction patterns were obtained by thermal analyzer and X-ray powder diffraction analyzer.Result,By analyzing the TG/DTA curves and XRD patterns of the free anthraquinones(Rhein,Emodin,Aloe-emodin,Chrysophanol and Physcion)from Rheum,the results showed that they had the similar TG curves,however,due to the substituents attached on the 1.8-dihydric anthraquinones are different,every sample had different weight lose.All the DTA curves of free anthraquinones had two obviously characteristic peaks,but there were obviously differences on curvilinear shapes,peak location and peak values.The X-ray powder diffraction patterns of free anthraquinones have their own characteristic and very obvious.Conclusion: According to the differences in the thermal and XRD properties of five free anthraquinones,the kind of free anthraquinones could be easily identified and they can be used as correspondence free anthraquinones’s characteristic fingerprint patterns.

热电材料计算机辅助XRD相分析方法与实现

讨论了热电材料相分析的特点和基于数据库技术的计算机辅助XRD相分析方法;并以PDF2粉末衍射文件为基准,创建了热电材料相分析数据库,实现了计算机辅助热电材料相分析;利用O rigin工具软件从衍射图谱中提取数据作为相分析标准数据的补充.

Silicon assistant carbothermal reduction for SiC powders

The silicon assistant method to increase the reaction yield of carbothermal reduction of silica at a lower temperature is reported. The effect of silicon on the carbothermal reduction process has been investigated in detail. Compared with traditional reduction, the introduction of silicon can change the reaction path and further increase the conversion of silicon carbide at a lower temperature. It is considered that the assistant reduction consists of three steps： vaporizing and melting of silicon, formation of silicon monoxide, and synthesis of silicon carbide. The morphology of the synthesized SiC powders through the silicon assistant method can be affected apparently by the experimental temperature.

Method for Measuring Residual Stresses Induced by Boring in Internal Surface of Tube and Its Validation with XRD Method

Residual stresses can have a strong effect on the usability of machined parts,and the X-ray diffraction(XRD)measuring equipment,which is commonly used to measure residual stresses,is very expensive.This paper presents a method of measuring the residual stresses induced by boring in the internal surface of a tube with much cheaper equipment.The method,called the strain-based method is mainly based on the strains measured on the external surface of the tube.It is proposed on the basis of the very long tube assumption.The finite element method(FEM)analysis is thus used to validate the length of the tube.Guided by the FEM results,an appropriate length of the tube is chosen,and the residual stresses are obtained from both the strain-based method and the XRD method.Stress profiles obtained from both two methods are compared.The comparison result indicates that the profiles of the two methods agree well with each other.Therefore,it can be concluded that the accuracy of the strain-based method is high enough,and it can be applied to residual stress measurement in practice.

Understanding the influence of petrographic parameters on strength of differently sized shale specimens using XRD and SEM

Ground failure is a major contributor to fatalities in underground mines in the US.Underground coal mines in the Northern Appalachian have weak roof rock composed of shale,which is prone to failure under high horizontal stress.Understanding the relationship among strength,specimen size and rock petrographic parameters is essential for developing an effective ground control plan.Size effect studies have found that rock strength varies with specimen size.This paper attempts to understand this strength variation using three specimen sizes(254-mm,508-mm,and 762-mm).The specimen strength was measured and the major petrographic parameters affecting the strength,namely grain size,grain shape,quartz content,clay content,etc.were analyzed using X-ray diffraction(XRD)and scanning electron microscopy(SEM).The petrographic parameters were then correlated with the strength of the three differently sized specimens.The results showed that 508-mm specimen had the lowest strength.Quartz content of the 508-mm specimen was lower than that of 254-mm and 762-mm specimens.Clay content and average grain size of the 508-mm specimen were higher than those of 254-mm and 762-mm specimens.These results clearly show that grain size,quartz content and clay content contribute to strength variation observed in differently sized shale specimens.

Characteristics of mechanical alloyed Ni-Al powder for sintering

Mechanical alloying was employed to obtain high-activity Ni-AI powder. The effects of mechanical alloying on the microstructure and characteristics of milled powder with a normal composition of Ni-22.89 at.% AI-0.5 at.% B were investigated by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, and transmission electron microscopy （TEM）. The results show that a solution Ni （AI） was obtained after milling. During mechanical alloying, the milled powder obtains extra surface energy and crystalline energy because the crystallite size becomes free and the lattice strain increases with the milling time prolonging. Furthermore, about 0.5 mol% oxide in the particles were formed after milling, and this kind of dis- persed oxide is effective to improve the properties of the sintered alloy by dispersion strengthening. It is confirmed that Ni3AI alloy with outstanding properties has been prepared with mechanical alloyed powders.

X-Ray Analysis by Williamson-Hall and Size-Strain Plot Methods of ZnO Nanoparticles with Fuel Variation

In this paper, a simple and facile surfactant assisted combustion synthesis is reported for the ZnO nanoparticles. The synthesis of ZnO-NPs has been done with the assistance of non-ionic surfactant TWEEN 80. The effect of fuel variations and comparative study of fuel urea and glycine have been studied by using characterization techniques like X-ray diffraction (XRD), transmission electron microscope (TEM) and particle size analyzer. From XRD, it indicates the presence of hexagonal wurtzite structure for ZnO-NPs. Using X-ray broadening, crystallite sizes and lattice strain on the peak broadening of ZnO-NPs were studied by using Williamson-Hall (W-H) analysis and size-strain plot. Strain, stress and energy density parameters were calculated for the XRD peaks of all the samples using (UDM), uniform stress deformation model (USDM), uniform deformation energy density model (UDEDM) and by the size-strain plot method (SSP). The results of mean particle size showed an inter correlation with W-H analysis, SSP, particle analyzer and TEM results.