基于Y-shaped路网的早高峰拼车定价策略

针对交通资源配置有限导致的早高峰通勤拥堵问题,借鉴共享经济理论,引入拼车出行概念,充分考虑通勤者出行方式和Y-shaped路网特点,建立了基于通勤者出行效益的拼车定价模型.模型结合费用补偿机制,讨论了以平台利润最大化和系统负效用最小化为目标的拼车定价策略,并给出了定价策略有效的阈值条件.研究结果表明,当通勤者都参与到拼车服务中时,拼车平台利润和交通系统负效用在其相应拼车定价策略下均能达到最优值,并且以交通系统负效用最小化为目标的拼车定价策略能消除Y-shaped路网中瓶颈处的交通拥堵.

A highly sensitive LITES sensor based on a multi-pass cell with dense spot pattern and a novel quartz tuning fork with low frequency

A highly sensitive light-induced thermoelectric spectroscopy(LITES)sensor based on a multi-pass cell(MPC)with dense spot pattern and a novel quartz tuning fork(QTF)with low resonance frequency is reported in this manuscript.An erbi-um-doped fiber amplifier(EDFA)was employed to amplify the output optical power so that the signal level was further enhanced.The optical path length(OPL)and the ratio of optical path length to volume(RLV)of the MPC is 37.7 m and 13.8 cm^(-2),respectively.A commercial QTF and a self-designed trapezoidal-tip QTF with low frequency of 9461.83 Hz were used as the detectors of the sensor,respectively.The target gas selected to test the performance of the system was acetylene(C2H2).When the optical power was constant at 1000 mW,the minimum detection limit(MDL)of the C2H2-LITES sensor can be achieved 48.3 ppb when using the commercial QTF and 24.6 ppb when using the trapezoid-al-tip QTF.An improvement of the detection performance by a factor of 1.96 was achieved after replacing the commer-cial QTF with the trapezoidal-tip QTF.

Gastrotracheal fistula:Treatment with a covered self-expanding Y-shaped metallic stent

A 67-year-old man had a sev-ere cough and pulmonary infection for 1 wk before seeking evaluation at our hospital.He had undergone esophagectomy with gastric pull-up and radiotherapy for esophageal cancer 3 years previously.After admission to our hospital,gastroscopy and bronchoscopy revealed a fistulous communication between the posterior tracheal wallnear the carina and the upper residual stomach.We measured the diameter of the trachea and bronchus and determined the site and size of the fistula using multislice computed tomography and gastroscopy.A covered self-expanding Y-shaped metallic stent was implanted into the trachea and bronchus.Subsequently,the fistula was closed completely.The patient tolerated the stent well and had good palliation of his symptoms.

Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide) synthesized by ATRP

Novel Y-shaped block copolymers of poly（ethylene glycol） and poly（N-isopropylacrylamide）, PEG-b-（PNIPAM）2, were successfully synthesized through atom transfer radical polymerization （ATRP）. A difunctional macroinitiator was prepared by esterification of 2,2-dichloroacetyl chloride with poly（ethylene glycol） monomethyl ether （PEG）. The copolymers were obtained via the ATRP ofN-isopropylacrylamide （NIPAM） at 30℃ with CuCl/Me6TREN as a catalyst system and DMF/H2O （v/v = 3：1） mixture as solvent. The resulting copolymers were characterized by gel permeation chromatography （GPC） and ^1H NMR. These block copolymers show controllable molecular weights and narrow molecular weight distributions （PDI 〈 1.15）. Their phase transition temperatures and the corresponding enthalpy changes in aqueous solution were measured by differential scanning calorimetry （DSC）. As a result, the phase transition temperature of PEG45-b-（PNIPAM55）2 is higher than that of PNIPAM, however, the corresponding enthalpy change is much lower, indicating the significant influence of the macromolecular composition and architecture on the phase transition.

Deformation and defects in hydroforming of Y-shaped tubes

Hydroforming process of a Y-shaped stainless steel tube was investigated through numerical simulation and experiments. The forming process and reasons of typical defects were analyzed with three different loading paths. Thickness distribution of formed Y-shaped tube was obtained. It is shown by numerical and experimental results that the transition regions are depressed in the forming condition of low inner pressure and wrinkles occur, while fracture occurs in the forming condition of high inner pressure. After forming, the thickness in left transition fillet region is the largest, that in fight transition fillet region is thinner, and the thinnest thickness is at the top of the protrusion. The original thickness line is below the top of the protrusion. The thinning area occurs above this line, while the thickening area is below this line. The maximum thinning rate is significantly increased as the calibration pressure increases, while the maximum thickening rate remains almost unchanged.

Binary collision approximation for solitary waves in a Y-shaped granular chain

We implement a binary collision approximation to study solitary wave propagation in a two-dimensional double Y- shaped granular chain. The solitary wave was transmitted and reflected when it met the interface of the bifurcated branches of the Y-shaped granular chains. We obtain the analytic results of the ratios of the transmitted and reflected speeds to the incident speed of the solitary wave, the maximum force between the two neighbor beads in a solitary wave, and the total time taken by the pulse to pass through each branch. All of the analytic results are in good agreement with the experimental observations from Daraio et al. [Phys. Rev. E 82 036603 （2010）]. Moreover, we also discuss the delay effects on the arrival of split pulses, and predict the recombination of the split waves traveling in branches in the final stem of asymmetric systems. The prediction of pulse recombination is verified by our numerical results.

VIBRATION MEASUREMENT OF DOUBLE-ENDED TUNING FORKS RESONATOR

To enhance the coherence and reliability of the double-ended tuning fork （DETF） resonator, a measurement system of resonator vibration is presented to check its dynamic characteristics. Laser Doppler techniques are utilized and the relation between DETF vibration velocity and output current of photodetector is obtained. Resonator vibration equation is also analyzed and its driving power only depends on the direct current bias voltage and the amplitude of alternative voltage. Furthermore, a special resonator driving control circuit based on measurement is designed. The amplitude and frequency of circuit is controlled by a computer so that highly stable and strong driving signal can be output. Experiments on driving and measuring double-ended tuning fork have been done, The frequency of driving signal is 8 kHz and the peak-to-peak value of driving voltage is 140 V. Experimental results indicate resonator can be drived stably by driving control circuit and dynamic characteristics of DETF may be measured in real time.

Evaluation of ultimate bearing capacity of Y-shaped vibro-pile

Based on Mindlin stress solution, a numerical computational method was proposed to calculate the stresses in the ground induced by side friction and the resistance of Y-shaped vibro-pile. The improved Terzaghi's and ЪерезанцевВГ's methods for ultimate bearing capacity evaluation were proposed by considering the stress strength induced by friction resistance at pile head level of Y-pile. A new method to calculate the ultimate bearing capacity of Y-pile was also proposed based on the assumptions of soil failure mode at the tip of Y-pile and the use of Mohr-Coulomb soil yield criterion and Vesic compressive correction coefficient with the induced stresses in the ground. Based on the comparisons with the field static load test results, it is found that the improved Terzaghi's method gives higher ultimate capacity, while the other two methods shows good agreement with the field results.

Transfer characteristics of dynamic biochemical signals in non-reversing pulsatile flows in a shallow Y-shaped microfluidic channel: signal filtering and nonlinear amplitude-frequency modulation

The transports of the dynamic biochemical signals in the non-reversing pulsatile flows in the mixing microchannel of a Y-shaped microfluidic device are ana- lyzed. The results show that the mixing micro-channel acts as a low-pass filter, and the biochemical signals are nonlinearly modulated by the pulsatile flows, which depend on the biochemical signal frequency, the flow signal frequency, and the biochemical signal transporting distance. It is concluded that, the transfer characteristics of the dynamic biochemical signals, which are transported in the time-varying flows, should be carefully considered for better loading biochemical signals on the cells cultured on the bottom of the microfluidic channel.

Y-Shaped Intra-Scleral Fixated Lens versus Retro-Pupillary Iris Claw Lens in the Treatment of Aphakia

Background: Many reasons can lead to an aphakia without adequate capsular support for implantation of a posterior chamber intraocular lens (IOL), such as intraoperative unintentional rupture of posterior capsule during phacoemulsification, planned intracapsular cataract extraction, ocular trauma and lens dislocation due to congenital and acquired causes. Purpose: To compare Y-shaped intra-scleral fixation of a posterior chamber IOL with retro pupillary fixation of an iris-claw intraocular lens (IOL) for Aphakic eyes without sufficient capsular support as respects safety, visual recovery and complications of both methods. Patients and Methods: One hundred Aphakic eyes were arbitrarily distributed between two groups. Group A included 50 eyes treated with retropupillary fixation of iris claw lens and group B included 50 eyes treated with Y-shaped intra-scleral fixation technique. Preoperative, intraoperative and postoperative data were analysed including best corrected visual acuity (BCVA), intraocular pressure (IOP), surgical time, intraoperative problems, IOL malposition and postoperative complications. Following up on patients was carried out for at least six months. Results: The mean duration of surgery was 21 ± 5.3 min in group A and was 53.4 ± 6.9 min in group B (p-value 0.05). IOL tilt was found in 0 (0%) eyes in group A and in 5 (10%) eyes in group B (p 0.05). Conclusion: The results of our study indicated that both methods are satisfactory in correcting aphakia without sufficient capsular support as regards postoperative best corrected visual acuity (BCVA);however the surgical technique of retropupillary iris claw lens is easier, shorter, with low intra- and postoperative complications and safer than those used for intra-scleral fixation of IOL. But for eyes which lack both iris and capsular support, a scleral fixation of a posterior chamber IOL remains the only option.

Comparison of lag screws and double Y-shaped miniplates in the fixation of anterior mandibular fractures

BACKGROUNDMandibular fractures constitute about 80.79% of maxillofacial injuries inAlexandria University, either as isolated mandibular fractures or as a part ofpanfacial fractures. The combination of symphyseal and parasymphyseal fracturesrepresent 47.09% of the total mandibular fractures.AIMTo compare the effectiveness of lag screws vs double Y-shaped miniplates in thefixation of anterior mandibular fractures.METHODSThis study is a prospective randomized controlled clinical trial, performed onsixteen patients with anterior mandibular fractures. Patients were divided equallyinto two groups, each consisting of eight patients. Group 1: Underwent openreduction and internal fixation using two lag screws. Group 2: Underwent openreduction and internal fixation using double Y-shaped plates. The followingparameters were assessed: operating time in minutes, pain using a visual analogscale, edema, surgical wound healing for signs and symptoms of infection,occlusion status and stability, maximal mouth opening, and sensory nervefunction. Cone beam computed tomography was performed at 3 and 6 mo tomeasure bone density and assess the progression of fracture healing.RESULTSThe study included 13 males (81.3%) and 3 females (18.8%) aged 26 to 45 years(mean age was 35.69 ± 6.01 years). The cause of trauma was road traffic accidentsin 10 patients (62.5%), interpersonal violence in 3 patients (18.8%) and othercauses in 3 patients (18.8%). The fractures comprised 10 parasymphyseal fractures(62.5%) and 6 symphyseal fractures (37.5%). The values of all parameters were comparable in both groups with no statistically significant difference except forthe mean bone density at 3 mo postoperatively which was 946.38 ± 66.29 in group 1 and 830.36 ± 95.53 in group 2 (P = 0.015).CONCLUSIONBoth lag screws and double Y-shaped miniplates provide favorable means offixation for mandibular fractures in the anterior region. Fractures fixed with lagscrews show greater mean bone density at 3 mo post-operation, indicative ofhigher primary stability and faster early bone healing. Further studies with largersample sizes are required to verify these conclusions.

基于Fork/Join的事务日志伴随模式挖掘方法

信息系统产生的大量事务日志数据蕴含着潜在的伴随模式,伴随模式是指在时空上频繁共现的一组对象.由于传统的滑动窗口算法和FP-Growth算法只能调用单一线程进行计算,随着数据规模的扩张,会导致挖掘伴随模式的时间急剧增加.为此本文提出了一种基于Fork/Join并行技术的伴随模式挖掘框架,其能够实现从单线程到多线程的迁移,充分利用多核配置的加速性能.该框架由划定伴随数据集、频繁项集挖掘和关联规则挖掘三部分组成.首先,提出了基于Fork/Join的多核并行滑动窗口算法,以缩短从事务日志中划定伴随数据集的时间;然后,提出基于Fork/Join的多核并行FP-Growth算法,以并行地挖掘伴随数据集中的频繁项集;最后,引入支持度、置信度和提升度3个参数,对伴随模式中各对象间的关联规则进行挖掘.基于门禁刷卡数据的实验结果表明,相比传统算法,本文所提出的框架能够挖掘出更多的伴随模式,同时挖掘效率较高.

Design and Development of a Vision-based Hydraulic Operated Mending Machine for Repairing 3W Forks

Three wheelers(3 Ws)are widely used in low and middle-income countries,particularly in Asia Pacific region as a comparatively cheap method to passenger transportation and goods delivery.The frequent use of 3 Ws in day-to-day activities have caused a large number of accidents causing injuries to their passengers.Less research has been carried out to identify the reasons behind 3 W accidents.The survey carried out prior to this research has identified that the stability control and speed control are the two key factors which the 3 W accidents attributed to.3 W fork is the main mechanical element that controls the balance and the stability of the vehicle.A damaged 3 W fork(a physical damage or a slight deformation)unbalances the 3 W and had been identified as one of the reasons for large number of accidents.Therefore,correctly reforming the damaged fork is of paramount importance,when concerning the safety of the 3 Ws.Traditionally,both heat-treating and cold-working techniques are used in the mending processes.Not only this manual-labor repairing process weakens the strength of the fork,but also the profile produced is inaccurate.This paper discusses a hydraulic operated fork mending machine with an image processing technique to reform the damaged forks in 3 Ws.An image comparator-based imaging technique is used for this machine vision-based visually guided fork repairing process.Three cameras have been used to capture the images from three perpendicular directions.A contour sketch of the original fork(before the deformation occurs)has been compared against the faulty fork,to assist the worker to carry out the repairing process.The preliminary experimentations have shown that the proposed technique can improve the repositioning of the camber angle by repairing the damaged fork.

Electrode design for multimode suppression of aluminum nitride tuning fork resonators

This paper is focused on electrode design for piezoelectric tuning fork resonators.The relationship between the performance and electrode pattern of aluminum nitride piezoelectric tuning fork resonators vibrating in the in-plane flexural mode is investigated based on a set of resonators with different electrode lengths,widths,and ratios.Experimental and simulation results show that the electrode design impacts greatly the multimode effect induced from torsional modes but has little influence on other loss mechanisms.Optimizing the electrode design suppresses the torsional mode successfully,thereby increasing the ratio of impedance at parallel and series resonant frequencies(R_(p)/R_(s))by more than 80%and achieving a quality factor(Q)of 7753,an effective electromechanical coupling coefficient(kt_(eff)^(2))of 0.066%,and an impedance at series resonant frequency(R_(m))of 23.6 kΩ.The proposed approach shows great potential for high-performance piezoelectric resonators,which are likely to be fundamental building blocks for sensors with high sensitivity and low noise and power consumption.

Compensation of Parasitic Capacitance of Quartz Tuning Fork in AFM

We have built an atomic force microscope using a quartz tuning fork as sensor. The excitation method we adopted, the electrical excitation, introduces stray capacitance into the signal-processing circuit. In this report, we demonstrated a simple but effective method to compensate for this parasitic capacitance by adding a compensator circuit consisting of an inverting amplifier and a capacitor. The capacitor is connected in series with the inverting amplifier and the compensator is connected in parallel with the quartz tuning fork. The resonance curve of the system measured after adding the homemade compensator resembles that of a pure RLC circuit, meaning that the stray capacitance is successfully eliminated. Furthermore, we tried to use our equipment to measure PDMS sample and got clean data. This system can be further combined with confocal microscope and diamond with NV defect to build scanning NV magnetometry.

超声造影联合血清Ficolin-3,FOXM1对2型糖尿病下肢动脉病变的诊断价值分析

目的超声造影联合血清纤维胶凝蛋白-3(Ficolin-3)、叉头框蛋白M1(FOXM1)对2型糖尿病(T2DM)下肢动脉病变的诊断价值分析。方法选取2022年2月至2023年2月我院收治的T2DM患者114例,以下肢动脉血管造影检查为金标准,将患者分为下肢动脉病变组23例(病变组)和无下肢动脉病变组91例(T2DM组),另选取同期于本院进行体检的健康志愿者91例为对照组。对患者及健康志愿者进行血清Ficolin-3、FOXM1及超声造影检查;ROC曲线分析血清Ficolin-3、FOXM1对T2DM下肢动脉病变的诊断价值;采用四格表法分析血清Ficolin-3、FOXM1、超声造影及3项联合对T2DM下肢动脉病变的诊断价值。结果病变组、T2DM组血清Ficolin-3水平显著高于对照组,且病变组血清Ficolin-3水平显著高于T2DM组(均P<0.05);病变组、T2DM组血清FOXM1水平显著低于对照组,且病变组血清FOXM1水平显著低于T2DM组(均P<0.05);血清Ficolin-3诊断T2DM下肢动脉病变的曲线下面积为0.868,敏感度为86.96%,特异度为75.82%,最佳截断值为35.12μg/ml;血清FOXM1诊断T2DM下肢动脉病变的曲线下面积为0.854,敏感度为82.61%,特异度为78.02%,最佳截断值为0.57;血清Ficolin-3、FOXM1检查结果与金标准均具有中度一致性(Kappa=0.480、0.481,均P<0.001);超声造影检查结果显示,T2DM下肢动脉病变的阳性检出率为73.91%,与金标准具有较高一致性(Kappa=0.631,P<0.001);3项联合检测的敏感度、漏诊率均显著优于超声造影单独诊断,准确度显著优于Ficolin-3、FOXM1单独诊断,差异均有统计学意义(均P<0.05)。结论血清Ficolin-3、FOXM1联合超声造影检查在T2DM下肢动脉病变诊断中的应用价值较高,进一步提升了诊断的敏感度、准确度,减少了误诊率。

织物和静电极板参数对静电吸附力的影响分析

为了明确织物和静电极板参数对静电吸附力的影响规律,为服装软面料的静电吸附式抓取提供理论支撑,文章开展织物参数和静电极板参数对静电吸附力影响规律的系统性研究。首先建立纬编织物结构模型及静电吸附力理论模型,通过理论分析结果和仿真结果的对比分析,验证仿真方法的有效性;接着基于Maxwell张量法推导了五层二维静电吸附力理论模型,分析静电吸附力模型结构参数对静电吸附力的影响规律,并得出结论:(1)静电吸附力和电极上施加电压的平方成正比;(2)织物密度越大,产生的静电吸附力越大;(3)绝缘层介电常数越大,静电吸附力越大;绝缘层厚度越大,静电吸附力越小;(4)随着极板占空比及电极间距的增大,静电吸附力均呈先增大后减小的趋势。

对称岔管结构与水力特性优化设计研究

岔管结构广泛应用于各类水利工程中,其结构安全和水力性能都是优化设计的关键,两者之间相互影响,又会对水利工程的综合性能和运行安全产生重要的影响。对某抽水蓄能电站对称岔管结构与水力特性进行优化设计,采用三维有限元法对岔管结构初设方案和优化方案进行了应力分析,计算结果表明优化后岔管腰线一侧应力分布情况相较初设方案得到有效改善。在岔管体型结构优化的基础上,分别对不同分岔角与肋宽比岔管的水力模型进行发电和抽水工况下的三维流场计算分析,通过正交优化策略确定了所有工况下内部流动分布较优、水头损失较小的分岔角与岔管肋宽比。研究发现,结构受力与水力特性之间并不是单纯的正相关关系,最终基于正交优化思想确定了满足结构安全与水力性能的最佳分岔角为75°、肋宽比为0.30。

分叉柱支承式单层曲面钢网壳施工过程监测研究

以云南红河综合交通枢纽单层曲面网壳为工程背景,对网壳结构、提升塔架的关键杆件布置测点进行施工过程监测研究,分析了结构在地面拼装及整体提升过程中内力的变化情况。通过对施工过程中网壳结构的温度效应进行研究,探讨了边界约束作用强弱对结构内力变化的影响程度,温度每变化1℃引起的网壳合拢后应力变化是合拢前应力变化的3倍;合拢后,温度每变化1℃引起网壳远离支座杆件的应力变化是靠近支座应力变化的2倍;对提升阶段监测数据进行分析,提升过程中实测应力波动范围在10 MPa以内,吊点提升同步性较好;此外,网壳结构卸载阶段监测数据表明,由于网壳提升状态与使用状态受力基本一致,网壳卸载前后应力变化较小,且卸载后支撑结构对温度敏感性较高。

缺血性疾病患者血清lncRNA PVT1和FOXM1表达水平及联合心脏磁共振延迟强化成像与预后的关系

目的 探讨缺血性疾病患者血清长链非编码RNA浆细胞瘤转化迁移基因1(lncRNA PVT1)和叉头框转录因子M1(FOX M1)表达水平及联合心脏钆对比剂延迟增强磁共振成像(LGE-MRI)与预后的关系。方法 选取2021年2月-2022年2月我院收治的缺血性心脏病患者118例即为研究组,随访一年根据随访过程中是否发生主要心脏不良事件(MACE),分为MACE组32例,无MACE组86例。同期选择在我院体检健康的志愿者118例为对照组。实时荧光定量PCR(qRT-PCR)检测血清lncRNA PVT1的相对表达量。采用酶联免疫吸附试验(E LISA)检测FOXM1水平。受试者工作特征(ROC)曲线分析LGE-MRI、血清lncRNA PVT1和FOXM1对缺血性心脏病患者预后发生MACE的预测价值。结果 研究组患者DBP、SBP、TG、TC、 LDL-C、GLU水平与对照组相比显著升高,HDL-C水平显著降低(P<0.05)。与对照组相比,研究组的血清中lncRNA PVT1和FOXM1水平显著升高(P<0.05)。与无MACE组相比,MACE组患者DBP、SBP、TC、LDL-C水平显著升高, HDL-C水平显著降低(P<0.05)。与无MACE组相比,MACE组患者血清中lncRNA PVT1和FOXM1水平显著升高(P<0.05)。MACE组的LGE-MRI阳性数量显著高于无MACE组(P<0.)05。与LGE-MRI、血清lncRNA PVT1和FOXM1单独预测相比,三者联合预测MACE发生的AUC更高(Z=7.221,P<0.001;Z=7.737,P<0.001;Z=7.091,P<0.001)。结论 缺血性心脏病预后发生MACE的患者血清lncRNA PVT1和FOXM1水平呈高表达,二者联合LGE-MRI对MACE的发生有一定的预测价值。