Interconnected microstructure and flexural behavior of Ti_(2)C-Ti composites with superior Young’s modulus

To enhance the Young’s modulus(E)and strength of titanium alloys,we designed titanium matrix composites with intercon-nected microstructure based on the Hashin-Shtrikman theory.According to the results,the in-situ reaction yielded an interconnected microstructure composed of Ti_(2)C particles when the Ti_(2)C content reached 50vol%.With widths of 10 and 230 nm,the intraparticle Ti lamellae in the prepared composite exhibited a bimodal size distribution due to precipitation and the unreacted Ti phase within the grown Ti_(2)C particles.The composites with interconnected microstructure attained superior properties,including E of 174.3 GPa and ultimate flexural strength of 1014 GPa.Compared with that of pure Ti,the E of the composite was increased by 55% due to the high Ti_(2)C content and interconnected microstructure.The outstanding strength resulted from the strong interfacial bonding,load-bearing capacity of interconnected Ti_(2)C particles,and bimodal intraparticle Ti lamellae,which minimized the average crack driving force.Interrupted flexural tests revealed preferential crack initiation along the{001}cleavage plane and grain boundary of Ti_(2)C in the region with the highest tensile stress.In addition,the propagation can be efficiently inhibited by interparticle Ti grains,which prevented the brittle fracture of the composites.

PSO algorithm for Young's modulus reconstruction

To get the quantitive value of abnormal biological tissues, an inverse algorithm about the Young＇s modulus based on the boundary extraction and the image registration technologies is proposed. With the known displacements of boundary tissues and the force distribution, the Young＇s modulus is calculated by constructing the unit system and the inverse finite element method （IFEM）. Then a tough range of the modulus for the whole tissue is estimated referring the value obtained before. The improved particle swarm optimizer （PSO） method is adopted to calculate the whole Yong＇s modulus distribution. The presented algorithm overcomes some limitations in other Young＇s modulus reconstruction methods and relaxes the displacements and force boundary condition requirements. The repetitious numerical simulation shows that errors in boundary displacement are not very sensitive to the estimation of next process; a final feasible solution is obtained by the improved PSO method which is close to the theoretical values obtained during searching in an extensive range.

A method to determine Young's modulus of soft gels for cell adhesion

A convenient technique is reported in this note for measuring elastic modulus of extremely soft material for cellular adhesion. Specimens of bending cylinder under gravity are used to avoid contact problem between testing device and sample, and a beam model is presented for evaluating the curvatures of gel beams with large elastic deformation. A self-adaptive algorithm is also proposed to search for the best estimation of gels＇ elastic moduli by comparing the experimental bending curvatures with those computed from the beam model with preestimated moduli. Application to the measurement of the property of polyacrylamide gels indi- cates that the material compliance varies with the concentrations of bis-acrylamide, and the gels become softer after being immersed in a culture medium for a period of time, no matter to what extent they are polymerized.

Measurement of Young's Modulus and Poisson's Ratio of Thermal Barrier Coatings

In gas turbines, thermal barrier coatings （TBCs） applied by air plasma spraying are widely used to lower the temperature of hot components. To analyze the characteristics of TBCs such as residual stress, bond strength, fracture toughness, and crack propagation ratio, the Young＇s modulus and Poisson＇s ratio are important parameters. For TBC is a brittle and thin film, it is desirable to evaluate those properties while the coatings are bonded to a substrate. An atmospheric plasma spray MCrAIY bond coat and Yttria stabilized zirconia （YSZ） top coat are deposited onto a nickel-base superalloy GH150 substrate. The Young＇s modulus and Poisson＇s ratio are measured by cantilever beam bending with NDI. The method will be developed to test the Young＇ s modulus and Poisson ratio of other multilayer systems.

Prediction and optimization of process variables to maximize the Young’s modulus of plasma sprayed alumina coatings on AZ31B magnesium alloy

Like other manufacturing techniques,plasma spraying has also a non-linear behavior because of the contribution of many coating variables.This characteristic results in finding optimal factor combination difficult.Subsequently,the issue can be solved through effective and strategic statistical procedures integrated with systematic experimental data.Plasma spray parameters such as power,stand-off distance and powder feed rate have significant influence on coating characteristics like Young’s modulus.This paper presents the use of statistical techniques in specifically response surface methodology(RSM),analysis of variance,and regression analysis to develop empirical relationship to predict Young’s modulus of plasma-sprayed alumina coatings.The developed empirical relationships can be effectively used to predict Young’s modulus of plasma-sprayed alumina coatings at 95%confidence level.Response graphs and contour plots were constructed to identify the optimum plasma spray parameters to attain maximum Young’s modulus in alumina coatings.A linear regression relationship was established between porosity and Young’s modulus of the alumina coatings.

Experimental Study on Young′s Modulus of Concrete

Young′s Modulus of concrete is studied on the basis of triaxial compressive experiments. The authors proposed two empirical equations to calculate its static Young′s modulus and dynamic Young′s modulus when dynamic Poisson ratio μ d varies nearby 0.20.P wave velocity and elastic modulus have the same varying tendency as letter N. μ,μ d decrease with the increase of loading rate and μ d has a great effect on the parameters E d and E D.

CALCULATION OF THE YOUNG'S MODULUS OF AN ADSORBED POLYMER LAYER

Polymer layers adsorbed to a surface or in a confined environment often change their mechanical properties. There is even the possibility of solidification of the confined layer. To judge the stiffness of such a layer, we used the Hertz model to calculate the Young＇s modulus of the polymer layer in the confinement of AFM experiments with silicon nitride tip with a radius of curvature ofR ≈ 50 nm and a glass sphere attached to the cantilever R =5 μm. Since there is no visible indentation of the layer in the AFM experiments, the layer is either penetrated very easily, or the indentation is too small to be seen in a force curve. The latter would be the case for a polymer layer with a Young＇s modulus above 4 × 10^8 Pa in case of an experiment with a silicon nitride tip and 4×10^5 Pa in case of a glass sphere.

Determination of reduced Young s modulus of thin films using indentation test

The flat cylindrical indentation tests with different sizes of punch radius were investigated using finite element method （FEM） aimed to reveal the effect of punch size on the indentation behavior of the film/substrate system. Based on the FEM results analysis, two methods was proposed to separate film＇s reduced Young＇s modulus from a film/substrate system. The first method was based on a new weight function that quantifies film＇s and substrate＇s contributions to the overall mechanical properties of the film/substrate system in the flat cylindrical indentation test. The second method, a numerical approach, including fitting and extrapolation procedures was put forward. Both of the results from the two methods showed a reasonable agreement with the one input FE model. At last, the effect of maximum indentation depth and the surface micro-roughness of the thin film on the reduced Young＇s modulus of the film/substrate system were discussed. The methods proposed in the present study provide some new conceptions on evaluating other properties of thin films, e.g. creep, for which a flat-ended punch is also employed.

Analysis of the elastic-plastic indentation properties of materials with varying ratio of hardness to Young’s modulus

The elastic-plastic indentation properties of materials with varying ratio of hardness to Young’s modulus(H/E) were analyzed with the finite element method. And the indentation stress fields of materials with varying ratio H/E on the surface were studied by the experiment. The results show that the penetration depth, contact radius, plastic pile-up and the degree of elastic recovery depend strongly on the ratio H/E. Moreover, graphs were established to describe the relationship between the elastic-plastic indentation parameters and H/E. The established graphs can be used to predict the H/E of materials when compared with experimental data.

Macroscopic Young’s Elastic Modulus Model of Particle Packing Rock Layers

Based on the Hertzian granular contact mechanics model, the paper built up a Macroscopic Young’s Elastic Modulus of particle/granular packing rock layers, and built up a ties to connecting Young’s Elastic Modulus of sand particle in Meso and the Macroscopic Young’s Modulus of granular packing rock layers. The Macroscopic Young’s Modulus of granular packing rock layers is far less than the Young’s Modulus of sand particle. The Macroscopic Young’s Modulus of granular packing rock layers is proportioned to the powers of 1/3 of the vertical contact force of sand particles. The Macroscopic Young’s Modulus is inversely proportional to particle diameter. The paper calculated the vertical contact force of five types aligning mode of the particles. When equal stress, the increased of the coordination number lead to the decrease of the contact force fn, this lead to the coordination number is an inverse proportion to Macroscopic Young’s Modulus. But the larger coordination number change only means very little Macroscopic Young’s Modulus change.

A New Elasticity and Finite Element Formulation for Different Young's Modulus When Tension and Compression Loadings

This paper presents a new elasticity and finite element formulation for different Young's modulus when tension and compression loadings in anisotropy media. The case studies, such as anisotropy and isotropy, were investigated. A numerical example was shown to find out the changes of neutral axis at the pure bending beams.

NANOINDENTATION OF THIN-FILM-SUBSTRATE SYSTEM DETERMINATION OF FILM HARDNESS AND YOUNG'S MODULUS

In the present paper,the hardness and Young's modulus of film-substrate systems are determined by means of nanoindentation experiments and modified models.Aluminum film and two kinds of substrates,i.e.glass and silicon,are studied.Nanoindentation XP Ⅱ and continuous stiffness mode are used during the experiments.In order to avoid the influence of the Oliver and Pharr method used in the experiments,the experiment data are analyzed with the constant Young's modulus assumption and the equal hardness assumption.The volume fraction model(CZ model)proposed by Fabes et al.(1992)is used and modified to analyze the measured hardness.The method proposed by Doerner and Nix(DN formula)(1986)is modified to analyze the measured Young's modulus.Two kinds of modified empirical formula are used to predict the present experiment results and those in the literature,which include the results of two kinds of systems,i.e.,a soft film on a hard substrate and a hard film on a soft substrate.In the modified CZ model,the indentation influence angle,(?), is considered as a relevant physical parameter,which embodies the effects of the indenter tip radius, pile-up or sink-in phenomena and deformation of film and substrate.

The influence of defects on the effective Young's modulus of a defective solid

It is difficult to establish structure-property relationships in a defective solid because of its inhomogeneous-geometry microstructure caused by defects. In the present research, the effects of pores and cracks on the Young’s modulus of a defective solid are studied. Based on the law of the conservation of energy, mathematical formulations are proposed to indicate how the shape, size, and distribution of defects affect the effective Young’s modulus. In this approach, detailed equations are illustrated to represent the shape and size of defects on the effective Young’s modulus. Different from the results obtained from the traditional empirical analyses, mixture law or statistical method, for the first time, our results from the finite element method （FEM） and strict analytical calculation show that the influence of pore radius and crack length on the effective Young’s modulus can be quantified. It is found that the longest crack in a typical microstructure of ceramic coating dominates the contribution of the effective Young’s modulus in the vertical direction of the crack.

Influence of Temperature Conditions on Dynamic Young’s Modulus Testing

The Young’s modulus was measured at high temperatures by impulse excitation of vibration method,and the effects of heating rate,holding time and temperature cycle on the test results were analyzed.The results show that the heating rate has obvious effect on the high temperature Young’s modulus of the green body,but has no obvious effect on that of the sintered products;the holding time of the heating process has no regular effect on the Young’s modulus,and the effect varies with the different products at a certain temperature;the method can also be used to test the Young’s modulus during cooling process.

Probing the effect of Young's modulus on the plugging performance of micro-nano-scale dispersed particle gels

The effect of mechanical strength of the dispersed particle gel(DPG)on its macro plugging performance is significant,however,little study has been reported.In this paper,DPG particles with different mechanical strengths were obtained by mechanical shearing of bulk gels prepared with different formula.Young’s moduli of DPG particles on the micro and nano scales were measured by atomic force microscope for the first time.The mapping relationship among the formula of bulk gel,the Young’s moduli of the DPG particles and the final plugging performance were established.The results showed that when the Young’s moduli of the DPG particles increased from 82 to 328 Pa,the plugging rate increased significantly from 91.46%to 97.10%due to the distinctly enhanced stacking density and strength at this range.While when the Young’s moduli of the DPG particles surpassed 328 Pa,the further increase of plugging rate with the Young’s moduli of the DPG particles became insignificant.These results indicated that the improvement of plugging rate was more efficient by adjusting the Young’s moduli of the DPG particles within certain ranges,providing guidance for improving the macroscopic application properties of DPG systems in reservoir heterogeneity regulation.

Biodegradation of Polymethylmethacrylate Bone Cement May Not Be a Serious Issue in Total Hip Arthroplasty—Retrieval Study for Knoop Hardness and Young’s Modulus

Introduction: To investigate a long-term in vivo deterioration of polymethylmethacrylate (PMMA) bone cement over time, we evaluated retrieved PMMA cement in terms of chemical elements presenting in the cement using energy dispersive analysis of X-rays;Knoop hardness;and the Young’s modulus using scanning acoustic microscopy. Materials and Methods: For mechanical evaluation, we could neglect the influences of entrapped air bubbles or blood by the use of small specimens. The study was based on thirteen cement samples (six used in the acetabulum and seven in the femur) derived from eight patients (age at revision surgery: mean 72.5, range 68 to 79). All of these samples were Simplex-P?cement. They were functioning well at least ten years after the previous surgery. Duration until revision surgery was ranged 12 to 25 years (average, 17.4 years). The reason for revision was aseptic mechanical loosening. Twenty samples of Simplex-Preg;cement were served by manually mixing as a control. Results: The average of the hardness of the cement was 17.0 ± 1.2 (range, 13.4-20.6). In the control, the hardness was 17.8 ± 1.5 (range, 14.0-24.6). There was no significant difference between these values. The mean of Young’s modulus of the cement was 5.61 ± 0.19 GPa (range, 5.09-6.10). In the control, the modulus was 6.04 ± 0.13 GPa (range, 5.68-6.45). Although the modulus was significantly less than that of the control, there was only 7% decrease in average between twelve and twenty-five years in vivo. Conclusions: Our results suggest that long-term implantation and functional loading in vivo may not be the limiting factor in the mechanical integrity of the bone cement.

Vibration of Gold Nano-Beam with Variable Young’s Modulus Due to Thermal Shock

In this paper, we will study the most important effects in the nano-scale resonator: the coupling effect of temperature and strain rate, and the non-Fourier effect in heat conduction. A solution for the generalized thermoelastic vibration of nano-resonator induced by thermal loading has been developed. The Young’s modulus is taken as a linear function of the reference temperature. The effects of the thermal loading and the reference temperature in all the studied fields have been studied and represented in graphs with some comparisons. The Young’s modulus makes significant effects on all the studied fields where the values of the temperature, the vibration of the deflection, stress, displacement, strain, stress-strain energy increase when the Young’s modulus has taken to be variable.

An improved model for predicting effective Young's modulus of the twisted structure under cyclic loading:taking into account the untwisting effect

Twist structures have diverse applications, ranging from dragline, electrical cable, and intelligent structure. Among these applications, tension deformation can＇t be avoided during the fabrication and working processes, which often leads to the twist structure rotation （called untwisting effect） and twist pitch increasing. As a consequence, this untwisting behavior has a large effect on the effective Young＇s modulus. In this paper, we present an improved model based on the classical Costello＇s theory to predict the effective Young＇s modulus of the basic structure, twisted by three same copper strands under cyclic loading. Series of experiments were carried out to verify the present model taking into account the untwisting effect. The experimental results have better agreements with the presented model than the common Costello＇s model.

EFFECT OF DISPERSION OF MICA IN MATRIX ON YOUNG'S MODULUS OF MICA FILLED POLYETHYLENE

The correlation between Young's modulus of mica-filled high density polyethylene (HDPE), low density polyethylene(LDPE) and the state of dispersion of plasma-treated mica in the polymer matrices was studied. The modulus and the number average diameter of mica aggregates in matrix were determined with tensile testing and image analysis respectively. The interface structure of the filler/matrix and the bulk structure of matrix were examined through the dielectric spectrometry, differential scanning calorimetry (DSC) and dynamic viscoelastic spectrometry. The results show that the Young's modulus of the filial polyethylene depends to a great extent upon the state of dispersion of filler in matrix, but it is independent of the interface structure and bulk structure. The better the dispersion, the higher the Young's modulus.

Self-adapting extraction of matrix mineral bulk modulus and verification of fluid substitution

Gassmann＇s equations are commonly used for predicting seismic wave velocity in rock physics research.However the input matrix mineral bulk modulus parameters are not accurate,which greatly influences the prediction reliability.In this paper,combining the Russell fluid factor with the Gassman-Biot-Geertsma equation and introducing the dry-rock Poisson＇s ratio,we propose an effective matrix mineral bulk modulus extraction method.This method can adaptively invert the equivalent matrix mineral bulk modulus to apply the Gassmann equation to fluid substitution of complex carbonate reservoirs and increase the fluid prediction reliability.The verification of the actual material fluid substitution also shows that this method is reliable,efficient,and adaptable.