MoS2/Zr composite films were deposited on the cemented carbide YT14 （WC＋14%TiC＋6%Co） by medium-frequency magnetron sputtered and coupled with multi-arc ion plated techniques.The influence of negative bias voltage ...MoS2/Zr composite films were deposited on the cemented carbide YT14 （WC＋14%TiC＋6%Co） by medium-frequency magnetron sputtered and coupled with multi-arc ion plated techniques.The influence of negative bias voltage on the composite film properties,including adhesion strength,micro-hardness,thickness and tribological properties were investigated.The results showed that proper negative bias voltage could significantly improve the mechanical and tribological properties of composite films.The effects of negative bias voltage on film properties were also put forward.The optimal negative bias voltage was -200 V under this experiment conditions.The obtained composite films were dense,the adhesion strength was about 60 N,the thickness was about 2.4 μm,and the micro-hardness was about 9.0 GPa.The friction coefficient and wear rate was 0.12 and 2.1×10-7 cm3/N·m respectively after 60 m sliding operation against hardened steel under a load of 20 N and a sliding speed of 200 rev·min-1.展开更多
The PZT thin films were prepared on （111）- Pt/Ti/SiO2/Si substrates by sol-gel method, and lead acetate [Pb（CH3COO）2], zirconium nitrate [Zr（NO3）4] were used as raw materials. The X-ray diffractometer （XRD） an...The PZT thin films were prepared on （111）- Pt/Ti/SiO2/Si substrates by sol-gel method, and lead acetate [Pb（CH3COO）2], zirconium nitrate [Zr（NO3）4] were used as raw materials. The X-ray diffractometer （XRD） and scanning electron microscopy （SEM） were used to characterize the phase structure and surface morphology of the films annealed at 650 ~C but with different holding time. Ferroelectric and dielectric properties of the films were measured by the ferroelectric tester and the precision impedance analyzer, respectively. The PZT thin films were constructed with epoxy resin as a composite structure, and the damping properties of the composite were tested by dynamic mechanical analyzer （DMA）. The results show that the films annealed for 90 minutes present a dense and compact crystal arrangement on the surface; moreover, the films also achieve their best electric quality. At the same time, the largest damping loss factor of the composite constructed with the 90 mins-annealed film shows peak value of 0.9, hi^her than the pure epoxy resin.展开更多
基金Funded by the National Natural Science Foundation of China (No.51075237)the National Basic Research Program of China (No.2009CB724402)+3 种基金the Taishan Scholar Program of Shandong Provincethe Outstanding Young Scholar Science Foundation of Shandong (No.JQ200917)the National Natural Science Foundation of Shandong (No.ZR2010EZ002)National High Technology Research and Development Program (No.2009AA044303)
文摘MoS2/Zr composite films were deposited on the cemented carbide YT14 （WC＋14%TiC＋6%Co） by medium-frequency magnetron sputtered and coupled with multi-arc ion plated techniques.The influence of negative bias voltage on the composite film properties,including adhesion strength,micro-hardness,thickness and tribological properties were investigated.The results showed that proper negative bias voltage could significantly improve the mechanical and tribological properties of composite films.The effects of negative bias voltage on film properties were also put forward.The optimal negative bias voltage was -200 V under this experiment conditions.The obtained composite films were dense,the adhesion strength was about 60 N,the thickness was about 2.4 μm,and the micro-hardness was about 9.0 GPa.The friction coefficient and wear rate was 0.12 and 2.1×10-7 cm3/N·m respectively after 60 m sliding operation against hardened steel under a load of 20 N and a sliding speed of 200 rev·min-1.
基金Supported by the National Natural Science Foundation of China (No. 50772083)China-Japan Cooperation Program(No. 2010DFA51270)the Fundamental Research Funds for the Central Universities
文摘The PZT thin films were prepared on （111）- Pt/Ti/SiO2/Si substrates by sol-gel method, and lead acetate [Pb（CH3COO）2], zirconium nitrate [Zr（NO3）4] were used as raw materials. The X-ray diffractometer （XRD） and scanning electron microscopy （SEM） were used to characterize the phase structure and surface morphology of the films annealed at 650 ~C but with different holding time. Ferroelectric and dielectric properties of the films were measured by the ferroelectric tester and the precision impedance analyzer, respectively. The PZT thin films were constructed with epoxy resin as a composite structure, and the damping properties of the composite were tested by dynamic mechanical analyzer （DMA）. The results show that the films annealed for 90 minutes present a dense and compact crystal arrangement on the surface; moreover, the films also achieve their best electric quality. At the same time, the largest damping loss factor of the composite constructed with the 90 mins-annealed film shows peak value of 0.9, hi^her than the pure epoxy resin.
