Dynamic response of mountain tunnel,bridge,and embankment along the Sichuan-Tibet transportation corridor to active fault based on model tests

The Sichuan-Tibet transportation corridor is prone to numerous active faults and frequent strong earthquakes.While extensive studies have individually explored the effect of active faults and strong earthquakes on different engineering structures,their combined effect remains unclear.This research employed multiple physical model tests to investigate the dynamic response of various engineering structures,including tunnels,bridges,and embankments,under the simultaneous influence of cumulative earthquakes and stick-slip misalignment of an active fault.The prototype selected for this study was the Kanding No.2 tunnel,which crosses the Yunongxi fault zone within the Sichuan-Tibet transportation corridor.The results demonstrated that the tunnel,bridge,and embankment exhibited amplification in response to the input seismic wave,with the amplification effect gradually decreasing as the input peak ground acceleration(PGA)increased.The PGAs of different engineering structures were weakened by the fault rupture zone.Nevertheless,the misalignment of the active fault may decrease the overall stiffness of the engineering structure,leading to more severe damage,with a small contribution from seismic vibration.Additionally,the seismic vibration effect might be enlarged with the height of the engineering structure,and the tunnel is supposed to have a smaller PGA and lower dynamic earth pressure compared to bridges and embankments in strong earthquake zones crossing active faults.The findings contribute valuable insights for evaluating the dynamic response of various engineering structures crossing an active fault and provide an experimental reference for secure engineering design in the challenging conditions of the Sichuan-Tibet transportation corridor.

Satellite Data-based Structural Mapping Reveals Active Panjal Traps Fault(PTF)in Kashmir,NW Himalaya

Exploring the evidence for unidentified earthquake-causing faults in the orogenic zones,and primarily the interior parts(Shah,2013),has been an ongoing quest for centuries(Willis,1923;Baker et al.,1988;Yeats et al.,1992;Wesnousky et al.,1999;Malik et al.,2010;Coudurier-Curveur et al.,2020;Shah et al.,2020).These faults are potentially dangerous due to their unknown risk and deformation budget,two of the most important aspects of mapping and understanding the vulnerability and hazards associated with active faults.

Active Fault Tolerant Nonsingular Terminal Sliding Mode Control for Electromechanical System Based on Support Vector Machine

Effective fault diagnosis and fault-tolerant control method for aeronautics electromechanical actuator is concerned in this paper.By borrowing the advantages of model-driven and data-driven methods,a fault tolerant nonsingular terminal sliding mode control method based on support vector machine(SVM)is proposed.A SVM is designed to estimate the fault by off-line learning from small sample data with solving convex quadratic programming method and is introduced into a high-gain observer,so as to improve the state estimation and fault detection accuracy when the fault occurs.The state estimation value of the observer is used for state reconfiguration.A novel nonsingular terminal sliding mode surface is designed,and Lyapunov theorem is used to derive a parameter adaptation law and a control law.It is guaranteed that the proposed controller can achieve asymptotical stability which is superior to many advanced fault-tolerant controllers.In addition,the parameter estimation also can help to diagnose the system faults because the faults can be reflected by the parameters variation.Extensive comparative simulation and experimental results illustrate the effectiveness and advancement of the proposed controller compared with several other main-stream controllers.

Geomorphological responses of rivers to active tectonics along the Karahay?t Fault, Western Türkiye

Understanding the topography in active tectonic areas and assessing the rates and models of active deformation in the upper crust are primary objectives in tectonic geomorphology studies. The drainage pattern of river systems is highly sensitive to tectonically induced changes, and it often preserves the records of the formation and progression of most tectono-geomorphic processes within its boundaries. Therefore, the evolution of landforms is a consequence of the evolution of individual drainage basins in which they are formed. Assessing the rates of tectonic deformation using geomorphic data is a traditionally adopted method to characterize the nature of active faults. Globally, the Digital Elevation Model(DEM) is widely used as a crucial tool to analyze the morphotectonic features of drainage basins. In this study, some geomorphic indices were applied to investigate the impact of tectonism on landscape along the Karahay?t Fault and its associated drainage areas. These geomorphic indices are mountain front sinuosity(Smf values between 1.17-1.52), valley floor width-to-height ratio(Vf values between 0.25-1.46), basin asymmetry factor(AF values between 15-72), drainage basin shape(Bs values between 3.18-6.01), hypsometric integral and curve(HI values between 0.32-047), channel sinuosity(S values between 1-1.6), normalized steepness index(Ksn values between 1-390) and Chi integral(χ values between 200-4400). The development of drainage areas on the hanging wall and footwall block of the Karahayit Fault differs depending on the uplift. The drainage areas developed on the hanging wall present different patterns depending on the regional uplift caused by the fault. This reveals that the fault contributed significantly to the development of drainage areas and regional uplift in the region. In addition, the maximum earthquake magnitude that may occur in the future on the Karahayit Fault, whose activity is supported by geomorphic indices, is calculated as 6.23. Since an earthquake of this magnitude may cause loss of life and property in the region, precautions should be taken.

Fractional Gradient Descent RBFNN for Active Fault-Tolerant Control of Plant Protection UAVs

With the increasing prevalence of high-order systems in engineering applications, these systems often exhibitsignificant disturbances and can be challenging to model accurately. As a result, the active disturbance rejectioncontroller (ADRC) has been widely applied in various fields. However, in controlling plant protection unmannedaerial vehicles (UAVs), which are typically large and subject to significant disturbances, load disturbances andthe possibility of multiple actuator faults during pesticide spraying pose significant challenges. To address theseissues, this paper proposes a novel fault-tolerant control method that combines a radial basis function neuralnetwork (RBFNN) with a second-order ADRC and leverages a fractional gradient descent (FGD) algorithm.We integrate the plant protection UAV model’s uncertain parameters, load disturbance parameters, and actuatorfault parameters and utilize the RBFNN for system parameter identification. The resulting ADRC exhibits loaddisturbance suppression and fault tolerance capabilities, and our proposed active fault-tolerant control law hasLyapunov stability implications. Experimental results obtained using a multi-rotor fault-tolerant test platformdemonstrate that the proposed method outperforms other control strategies regarding load disturbance suppressionand fault-tolerant performance.

Large-scale shaking table test on unlined tunnel in fault zone under threedimensional earthquake

A fault is a geological structure characterized by significant displacement of rock masses along a fault plane within the Earth's crust.The Yunnan Tabaiyi Tunnel intersects multiple fault zones,making tunnel construction in fault-prone areas particularly vulnerable to the effects of fault activity due to the complexities of the surrounding geological environment.To investigate the dynamic response characteristics of tunnel structures under varying surrounding rock conditions,a three-dimensional large-scale shaking table physical model test was conducted.This study also aimed to explore the damage mechanisms associated with the Tabaiyi Tunnel under seismic loading.The results demonstrate that poor quality surrounding rock enhances the seismic response of the tunnel.This effect is primarily attributed to the distribution characteristics of acceleration,dynamic strain,and dynamic soil pressure.A comparison between unidirectional and multi-directional(including vertical)seismic motions reveals that vertical seismic motion has a more significant impact on specific tunnel locations.Specifically,the maximum tensile stress is observed at the arch shoulder,with values ranging from 60 to 100 k Pa.Moreover,NPR(Non-Prestressed Reinforced)anchor cables exhibit a substantial constant resistance effect under low-amplitude seismic waves.However,when the input earthquake amplitude reaches 0.8g,local sliding occurs at the arch shoulder region of the NPR anchor cable.These findings underscore the importance of focusing on seismic mitigation measures in fault zones and reinforcing critical areas,such as the arch shoulders,in practical engineering applications.

Normal faulting and its role in the drainage divide migration in the Karιncalιda?region,Menderes Massif,Western Türkiye

Drainage divide migration refers to the shifting boundaries between adjacent drainage basins over time,driven by processes such as tectonic uplift,differential erosion,stream capture,and lithological variations.This phenomenon has a significant impact on water flow patterns and basin extents,serving as an indicator of the landscape's response to active tectonic forces.One of the key drivers of divide migration is asymmetric uplift,which causes divides to shift from areas of lower uplift to regions experiencing higher uplift.Drainage divides are inherently dynamic,evolving over time as drainage networks develop and adjust to changing conditions.This study focuses on the migration of the main drainage divide along Karιncalιda?,located between Bozdo?an and Karacasu.It employs geomorphic analyses using metrics such as the normalized steepness index(ksn),Chi(χ),and Gilbert metrics.The main divide is categorized into four segments(D1–D4),with the Karacasu Fault,situated along the mountain's north-eastern boundary,identified as the primary factor influencing divide dynamics.Secondary factors include the relatively low elevation of Karιncalιda?,uniform lithology,and consistent rainfall patterns across the region.The results indicate that the main divide is currently stable,suggesting a balance between uplift and erosion.However,higherχvalues in the D4 segment suggest that future erosion may dominate,potentially causing the divide to migrate toward the Bozdo?an Basin.These findings highlight the dynamic nature of drainage divides and the complex interplay of tectonic,erosional,and lithological processes that shape their evolution.Continued monitoring and advanced geomorphic analysis are essential for understanding the long-term stability of the divide and its response to future tectonic activity and erosional modifications.

Deformation mechanism and NPR anchor cable truss coupling support in tunnel through fault fracture zone

To address the issue of extensive deformation in the Tabaiyi Tunnel caused by the fault zone,nuclear magnetic resonance(NMR)technology was employed to analyze the physical and mechanical properties of waterabsorbing mudstone.This analysis aimed to understand the mechanism behind the significant deformations.Drawing from the principle of excavation stress compensation,a support scheme featuring NPR anchorcables and an asymmetric truss support system was devised.To validate the scheme,numerical analysis using a combination of the Discrete Element Method(DEM)-Finite Element Method(FEM)was conducted.Additionally,similar material model tests and engineering measurements were carried out.Field experiments were also performed to evaluate the NPR anchor-cable and truss support system,focusing on anchor cable forces,pressures between the truss and surrounding rock,pressures between the initial support and secondary lining,as well as the magnitude of settlement and convergence deformation in the surrounding rock.The results indicate that the waterinduced expansion of clay minerals,resulting from damage caused by fissure water,accelerated the softening of the mudstone's internal structure,leading to significant deformations in the Tabaiyi Tunnel under high tectonic stress.The original support design fell short as the length of the anchor rods was smaller than the expansion depth of the plastic zone.As a result,the initial support structure bore the entire load from the surrounding rock,and a non-coupled deformation contact was observed between the double-arch truss and the surrounding rock.The adoption of NPR asymmetric anchor-cable support effectively restrained the expansion and asymmetric distribution characteristics of the plastic zone.Considering the mechanical degradation caused by water absorption in mudstone,the rigid constraint provided by the truss proved crucial for controlling the stability of the surrounding rock.These research findings hold significant implications for managing large deformations in soft rock tunnels situated within fractured zones under high tectonic stress conditions.

Seismic analysis of the active character of the Taihang Mountain piedmont fault

The Taihang Mountain piedmont fault is a large-scale structure zone in north and east China which cross Beijing,with the NE-NNE extent spans approximately 620 km.It is very important to determine the fault zone activity due to the close relation of active structures and earthquakes.Regarding the fault activity,there are three different opinions：1） it is a large deep fault zone;2） it is an active fault zone and an earthquake structure belt;and 3） it is not an earthquake structure belt.In order to ascertain the active character of the fault,the deep tectonic setting and the activity since the Quaternary were investigated using recent seismic and drilling data to make a joint interpretation.The investigation results show that the Taihang Mountain piedmont fault is not a large lithospheric fault because the early middle Pleistocene（Q（P2）） layers are offset by the fault and the late middle Pleistocene（Q（P2）） and late Pleistocene layers are not offset by the fault.We determine that the Taihang Mountain piedmont fault in the area is not an active fault and is also not a large lithospheric fault.This study result provides important geological and geophysical data for city planning and construction in Hebei province and, especially,has great significance for seismic hazard assessment of the capital area.

The numerical simulation and inversion fitting of radon concentration distribution in homogeneous overburden above active fault zones

Based on the convection and diffusion mechanisms of radon migration, in this paper we deduce the two-dimensional differential equation for radon transportation in the overburden above active fault zones with an unlimited extension along the strike. Making use of the finite difference method, the radon concentration distribution in the overburden above active faults is calculated and modeled. The active fault zone parameters, such as the depth and the width of the fault zone, and the value of radon concentration, can be inverted from the measured radon concentration curve. These realize quantitative interpretation for radon concentration anomalies. The inversion results are in good agreement with the actual fault zone parameters.

Active Faulting Pattern,Present-day Tectonic Stress Field and Block Kinematics in the East Tibetan Plateau

This paper examines major active faults and the present-day tectonic stress field in the East Tibetan Plateau by integrating available data from published literature and proposes a block kinematics model of the region. It shows that the East Tibetan Plateau is dominated by strike-slip and reverse faulting stress regimes and that the maximum horizontal stress is roughly consistent with the contemporary velocity field, except for the west Qinling range where it parallels the striking of the major strike-slip faults. Active tectonics in the East Tibetan Plateau is characterized by three faulting systems. The left-slip Kunlun-Qinling faulting system combines the east Kunlun fault zone, sinistral oblique reverse faults along the Minshan range and two major NEE-striking faults cutting the west Qinling range, which accommodates eastward motion, at 10--14 mm/a, of the Chuan-Qing block. The left-slip Xianshuihe faulting system accommodated clockwise rotation of the Chuan-Dian block. The Longmenshan thrust faulting system forms the eastern margin of the East Tibetan Plateau and has been propagated to the SW of the Sichuan basin. Crustal shortening across the Longmenshan range seems low （2-4 mm/a） and absorbed only a small part of the eastward motion of the Chuan-Qing block. Most of this eastward motion has been transmitted to South China, which is moving SEE-ward at 7-9 mm/a. It is suggested from geophysical data interpretation that the crust and lithosphere of the East Tibetan Plateau is considerably thickened and theologically layered. The upper crust seems to be decoupled from the lower crust through a decollement zone at a depth of 15-20 kin, which involved the Longmenshan fault belt and propagated eastward to the SW of the Sichuan basin. The Wenchuan earthquake was just formed at the bifurcated point of this decollement system. A rheological boundary should exist beneath the Longmenshan fault belt where the lower crust of the East Tibetan Plateau and the lithospheric mantle of the Yangze block are juxtaposed.

Distribution patterns of rock mass displacement in deeply buried areas induced by active fault creep slip at engineering scale

Active fault creep slip induces deformation of rock mass buried deeply in fault zones that significantly affect the operational safety of long linear projects passing through it.Displacement distribution patterns of rock masses in active fault zones which have been investigated previously are the key design basis for such projects.Therefore,a discrete element numerical model with different fault types,slip time,dip angles,and complex geological features was established,and then the creep slip for normal,reverse,and strike-slip faults were simulated to analyze the displacement distribution in the fault rock mass.A disk rotation test system and the corresponding laboratory test method were developed for simulating rock mass displacement induced by creep slippage of faults.A series of rotation tests for softand hard-layered specimens under combined compression and torsional stress were conducted to verify the numerical results and analyze the factors influencing the displacement distribution.An S-shaped displacement distribution independent of fault dip angle was identified corresponding to reverse,normal,and strike-slip faults.The results indicated that the higher the degree of horizontal extrusion,the softer the rock mass at the fault core,and the higher the degree of displacement concentration in the fault core;about 70%of the creep slip displacement occurs within this zone under 100 years of creep slippage.

Shallow crustal velocity structures revealed by active source tomography and fault activities of the Mianning–Xichang segment of the Anninghe fault zone, Southwest China

The Anninghe fault is a large left-lateral strike-slip fault in southwestern China. It has controlled deposition and magmatic activities since the Proterozoic, and seismic activity occurs frequently. The Mianning-Xichang segment of the Anninghe fault is a seismic gap that has been locked by high stress. Many studies suggest that this segment has great potential for large earthquakes(magnitude >7). We obtained three vertical velocity profiles of the Anninghe fault(between Mianning and Xichang) based on the inversion of P-wave first arrival times. The travel time data were picked from seismograms generated by methane gaseous sources and recorded by three linearly distributed across-fault dense arrays. The inversion results show that the P-wave velocity structures at depths of 0-2 km corresponds well with the local lithology. The Quaternary sediments have low seismic velocities, whereas the igneous rocks,metamorphic rocks, and bedrock have high seismic velocities. We then further discuss the fault activities of the two fault branches of the Anninghe fault in the study region based on small earthquakes(magnitudes between ML 0.5 and ML 2.5) detected by the Xichang array.The eastern fault branch is more active than the western branch and that the fault activities in the eastern branch are different in the northern and southern segments at the border of 28°21′N. The high-resolution models obtained are essential for future earthquake rupture simulations and hazard assessments of the Anninghe fault zone. Future studies of velocity models at greater depths may further explain the complex fault activities in the study region.

Earthquake recurrence on whole active fault zones and its relation to that on individual fault-segments

Based on the earthquake data of 11 active intraplate fault zones of the Chinese mainland, we have studied the earthquake recurrence behaviors on entire active fault zones and their relations to those on individual fault-segments. The results show that the earthquake recurrence on entire active fault zones, each of them is made up of multiple segments, displays three types of behavior, i.e., the clustering behavior, the random behavior, and the poor quasi-periodic behavior. The major one is the sparse clustering behavior, its recurrence process often exhibits that clusters (active periods) and gaps (quiescent periods) occur alternatively in varying degrees. The recurrence intervals within and between clusters, the durations of individual clusters, the earthquake number and strength of every cluster are all variable. The recurrence process is non-linear, there is neither the strength-time dependence nor the time-strength dependence. However, the earthquake recurrence processes on individual fault-segments are much more simple, and mainly display either the quasi-periodic or the time-predictable behaviors. Also, this study further discovers that the temporal clustering in earthquake recurrence process on entire fault zones is mainly caused by the rupture 'contagion' on different fault-segments within relatively short periods of time. Along active fault zones, the degree and orientation of rupture 'contagion' may vary with different seismic cycles, and the 'contagion' seems to be able to jump over unbroken 'gaps' on the fault zones.

Uniform Strike-Slip Rate along the Xianshuihe-Xiaojiang Fault System and Its Implications for Active Tectonics in Southeastern Tibet

Recent studies on the Xianshuihe-Xiaojiang fault system suggest that the Late Quaternary strike-slip rate is approximately uniform along the entire length of the fault zone, about 15±2 mm/a. This approximately uniform strike slip rate strongly supports the clockwise rotation model of the southeastern Tibetan crust. By approximating the geometry of the arc-shaped Xianshuihe-Xiaojiang fault system as a portion of a small circle on a spherical Earth, the 15±2 mm/a strike slip rate corresponds to clockwise rotation of the Southeastern Tibetan Block at the （5.2±0.7）×10^-7 deg/a angular velocity around the pole （21°N, 88°E） relative to the Northeast Tibetan Block. The approximately uniform strike slip rate along the Xianshuihe-Xiaojiang fault system also implies that the Longmeushan thrust zone is not active, or at least its activity has been very weak since the Late Quaternary. Moreover, the total offset along the Xiaushuihe-Xiaojiang fault system suggests that the lateral extrusion of the Southeastern Tibetan Block relative to Northeastern Tibetan Block is about 160 km and 200-240 km relative to the Tarim-North China block. This amount of lateral extrusion of the Tibetan crust should have accommodated about 13-24% convergence between India and Eurasia based on mass balance calculations. Assuming that the slip rate of 15±2 mm/a is constant throughout the entire history of the Xianshuihe-Xiaojiang fault system, 11±1.5 Ma is needed for the Xianshuihe-Xiaojiang fault system to attain the 160 km of total offset. This implies that left-slip faulting on the Xianshuihe-Xiaojiang fault system might start at 11±1.5 Ma.

Main active faults and seismic activity along the Yangtze River Economic Belt:Based on remote sensing geological survey

The Yangtze River Economic Belt(YREB)spans three terrain steps in China and features diverse topography that is characterized by significant differences in geological structure and presentday crustal deformation.Active faults and seismic activity are important geological factors for the planning and development of the YREB.In this paper,the spatial distribution and activity of 165 active faults that exist along the YREB have been compiled from previous findings,using both remote-sensing data and geological survey results.The crustal stability of seven particularly noteworthy typical active fault zones and their potential effects on the crustal stability of the urban agglomerations are analyzed.The main active fault zones in the western YREB,together with the neighboring regional active faults,make up an arc fault block region comprising primarily of Sichuan-Yunnan and a“Sichuan-Yunnan arc rotational-shear active tectonic system”strong deformation region that features rotation,shear and extensional deformation.The active faults in the central-eastern YREB,with seven NE-NNE and seven NW-NWW active faults(the“7-longitudinal,7-horizontal”pattern),macroscopically make up a“chessboard tectonic system”medium-weak deformation region in the geomechanical tectonic system.They are also the main geological constraints for the crustal stability of the YREB.

Recurrence behaviors of segment-rupturing earthquakes on active faults of the Chinese mainland

To investigate the recurrence behaviors of segment-rupturing eathquakes on active faults of the Chinese mainland, thispaper analyzes quantitatively earthquake history of 19 fault segments based on earthquake dam of multi-cyclerecurrences. The result shows that, for these fault segments, eanhquake recurring at previous locations is mainlycharacterized by both quasi-periodic (in a ratio of about) and time-predictable (in a ratio of about) behaviors.For the first behavior. intrinsic uncertainty of recurrence interval accounts for 0. 15-0.40 of the average interval, andmagnitudes of event vary from cycle to cycle within the range of the mean magnitUde t0.5. For the second behavior,intrinsic uncertainty of recurrence interval ranges mostly from 0. 19 to 0.40 of the average interval, and for successivetwo cycles the maximum change of event magnitudes is as much as 1.7 magnitude-units. In addition, for a few casesthe first behavior coexists along with either the second or the slip-predictable behaviors.

A Comprehensive Investigation of an Offshore Active Fault in the Western Sagami Bay, Central Japan

Offshore active faults, especially those in the deep sea, are very difficultto study because of the water and sedimentary cover. To characterize the nature and geometry ofoffshore active faults, a combination of methods must be employed. Generally, seismic profiling isused to map these faults, but often only fault-related folds rather than fracture planes are imaged.Multi-beam swath bathymetry provides information on the structure and growth history of a faultbecause movements of an active fault are reflected in the bottom morphology. Submersible anddeep-tow surveys allow direct observations of deformations on the seafloor (including fracture zonesand microstructures). In the deep sea, linearly aligned cold seep communities provide indirectevidence for active faults and the spatial migration of their activities. The Western Sagami Bayfault (WSBF) in the western Sagami Bay off central Japan is an active fault that has been studied indetail using the above methods. The bottom morphology, fractured breccias directly observed andphotographed, seismic profiles, as well as distribution and migration of cold seep communitiesprovide evidence for the nature and geometry of the fault. Focal mechanism solutions of selectedearthquakes in the western Sagami Bay during the period from 1900 to 1995 show that the maximumcompression trends NW-SE and the minimum stress axis strikes NE-SW, a stress pattern indicating aleft-lateral strike-slip fault.

Analyses of active faults, seismic activities and sea floor unstable factors of the Zhujiang River Mouth Basin and its adjacent areas

-On the basis of the data of geophysics and seismic activities, the analyses of the active faults, seismic activities and the sea floor unstable factors of the Zhujiang River Mouth Basin have been made so as to study the characteristics of the compressional subactive continental margin of Cathaysian system, arc littoral strongly active fracture zone, the division of seismic subzone and seismic zone of the continental margin of northern South China Sea, the potential focal area, and to analyze the regional stability. We consider that the Zhujiang River Mouth Basin belongs to a stable or a moderately stable region.

A new early-warning prediction system for monitoring shear force of fault plane in the active fault

The most common method used to describe earthquake activity is based on the changes in physical parameters of the earth＇s surface such as displacement of active fault and seismic wave.However,such approach is not successful in forecasting the movement behaviors of faults.In the present study,a new mechanical model of fault activity,considering the shear strength on the fault plane and the influence of the resistance force,is established based on the occurrence condition of earthquake.A remote real-time monitoring system is correspondingly developed to obtain the changes in mechanical components within fault.Taking into consideration the local geological conditions and the history of fault activity in Zhangjiakou of China,an active fault exposed in the region of Zhangjiakou is selected to be directly monitored by the real-time monitoring technique.A thorough investigation on local fault structures results in the selection of two suitable sites for monitoring potential active tectonic movements of Zhangjiakou fault.Two monitoring curves of shear strength,recorded during a monitoring period of 6 months,turn out to be steady,which indicates that the potential seismic activities hardly occur in the adjacent region in the near future.This monitoring technique can be used for early-warning prediction of the movement of active fault,and can help to further gain an insight into the interaction between fault activity and relevant mechanisms.