A review on metal additive manufacturing:modeling and application of numerical simulation for heat and mass transfer and microstructure evolution

Metal additive manufacturing technology has been widely used in prototyping,parts manufacturing and repairing.Metal additive manufacturing is a multi-scale and multi-physical coupling process with complex physical phenomena of heat and mass transfer and microstructure evolution.It is hard to directly observe the dynamic behavior and microstructure evolution of molten pool during additive manufacturing.Therefore,numerical simulation of additive manufacturing process is significant since it can efficiently and pertinently predict and analyze the physical phenomena in the process of metal additive manufacturing,and provide a reference for technological parameters selection.In this review,the research progress of numerical simulation of metal additive manufacturing is discussed.Various aspects of numerical simulation models are reviewed,including:(1)Introduction of basic control method and physical description of numerical simulation models;(2)Comparison of various heat and mass transfer models based on different physical assumptions(heat conduction model;heat flux coupling model;discrete powder particle heat flux coupling model);(3)Applications of various microstructure evolution models[phase field(PF),cellular automata(CA),and Monte Carlo(MC)].Finally,the development trend of numerical simulation of metal additive manufacturing,including the thermal-flow-solid coupling model and deep learning for numerical model,is analyzed.

Slag Characteristics of Biomass Pellet Fuels with Different Additives to Tobacco-Stalk for Tobacco Curing Heating

Since pure tobacco stalk(TS)biomass pellet fuels tend to slag,five anti-slagging agents were added to the crushed TS to obtain a pellet fuel that could be used in biomass burners to provide heat for tobacco curing.The obtained results revealed that the main component of TS pellet fuel was K_(2)Si_(2)O_(5).During fuel combustion process,additives generated higher melting point silicate compounds by Al–K,Ca–K,and Ca–K elemental structures to replace single K elemental structure of TS,enhancing the anti-slagging efficiency of the pellet fuel from 21.63%to 78.29%and promoting the precipitation of K,Mg,and Na elements in the slag block.By investigating the anti-slagging mechanism pathways of the additives in TS biomass pellet fuels,altering of the structure of silicate ion group pathway was found to improve anti-slagging effects that met the requirements of production formula.

Robust interface and excellent as-built mechanical properties of Ti–6Al–4V fabricated through laser-aided additive manufacturing with powder and wire

The feasibility of manufacturing Ti-6Al-4V samples through a combination of laser-aided additive manufacturing with powder(LAAM_(p))and wire(LAAM_(w))was explored.A process study was first conducted to successfully circumvent defects in Ti-6Al-4V deposits for LAAM_(p) and LAAM_(w),respectively.With the optimized process parameters,robust interfaces were achieved between powder/wire deposits and the forged substrate,as well as between powder and wire deposits.Microstructure characterization results revealed the epitaxial prior β grains in the deposited Ti-6Al-4V,wherein the powder deposit was dominated by a finerα′microstructure and the wire deposit was characterized by lamellar α phases.The mechanisms of microstructure formation and correlation with mechanical behavior were analyzed and discussed.The mechanical properties of the interfacial samples can meet the requirements of the relevant Aerospace Material Specifications(AMS 6932)even without post heat treatment.No fracture occurred within the interfacial area,further suggesting the robust interface.The findings of this study highlighted the feasibility of combining LAAM_(p) and LAAM_(w) in the direct manufacturing of Ti-6Al-4V parts in accordance with the required dimensional resolution and deposition rate,together with sound strength and ductility balance in the as-built condition.

Anterior mediastinal masses and thymic cysts

Cystic lesions of the anterior mediastinum in children suggest a well-known group of benign lesions that are comparatively frequent.Thymic cysts(TCs)are mostly positioned in the anterior mediastinum and some patients in the neck.Benign TCs classified as congenital intra-thoracic mesothelial cysts are commonly asymptomatic and have slight clinical significance.Multilocular TC,which can mimic another anterior mediastinal cystic tumor and is seen in adults,is more clinically important.It is a sporadic mediastinal lesion thought to arise in the course of acquired inflammation.Congenital mediastinal cysts represent 3%-6%of all mediastinal tumors and 10%-18%of radiologically reported mediastinal masses.Mediastinal TCs are uncommon and it is hard to know their true incidence.About 60%of cases with mediastinal TCs are asymptomatic,and the remainder of patients complains of nonspecific symptoms(e.g.,chest pain,dyspnea,or cough).The literature suggests that most cysts are benign,but an indefinite percentage may have a neoplastic process and result in significant compressive symptoms over time.Clinical symptoms of TCs vary depending on the location.In addition,frequent symptoms at the appearance of enlarged benign thymic and mediastinal cysts generally contain compressive symptoms(e.g.,respiratory distress,thymic pain,and symptoms related to Horner syndrome,hoarseness,dysphonia,dyspnea,orthopnea,wheezing,and fever).Many TCs have cystic density and a neat border and are simple to diagnose with radiological imaging.However,some TCs are hard to identify before surgery and may be misidentified as thymomas depending on their site and computed tomography results.Excision by thoracotomy,median sternotomy,or video-assisted techniques is essential for conclusive diagnosis,management,and abolition of relapse of anterior mediastinal masses and TCs.Histopathologic examination may be required after surgery.Considering the extent of the mass and the preliminary inability to make a definitive diagnosis,en bloc excision of the cyst was thought to be preferred to circumvent likely complications(e.g.,perforation,spillage of the contents,or incomplete excision).

Standard Model Fermion Masses and Charges from Holographic Analysis

The Standard Model of particle physics involves twelve fundamental fermions, treated as point particles, in four charge states. However, the Standard Model does not explain why only three fermions are in each charge state or account for neutrino mass. This holographic analysis treats charged Standard Model fermions as spheres with mass 0.187 g/cm2 times their surface area, using the proportionality constant in the holographic relation between mass of the observable universe and event horizon radius. The analysis requires three Standard Model fermions per charge state and relates up quark and down quark masses to electron mass. Holographic analysis specifies electron mass, to six significant figures, in terms of fundamental constants α,ℏ,G,Λ and Ω Λ . Treating neutrinos as spheres and equating electron neutrino energy density with cosmic vacuum energy density predicts neutrino masses consistent with experiment.

Stability analysis of approximately multidimensional additive mappings on fuzzy spaces

The intention of this paper is to study new additive kind multi-dimensional functional equations inspired by several applications of difference equations in biology,control theory,economics,and computer science,as well as notable implementation of fuzzy ideas in certain situations involving ambiguity or vagueness.In the context of different fuzzy spaces,we demonstrate their various fundamental stabilities related to Ulam stability theory.An appropriate example is given to show how stability result fails when the singular case occurs.The findings of this study suggest that stability results are valid in situations with uncertain or imprecise data.The stability results obtained under these fuzzy spaces are compared with previous stability results.

Improved isochronous mass spectrometry with tune measurement

In conventional isochronous mass spectrometry(IMS)performed on a storage ring,the precision of mass measurements for short-lived nuclei depends on the accurate determination of the revolution times(T)of stored ions.However,the resolution of T inevitably deteriorates due to the magnetic rigidity spread of the ions,limiting the mass-resolving power.In this study,we used the betatron tunes Q(the number of betatron oscillations per revolution)of the ions and established a correlation between T and Q.From this correlation,T was transformed to correspond to a fixed Q with higher resolution.Using these transformed T values,the masses of ^(63)Ge,^(65)As,^(67)Se,and ^(71)Kr agreed well with the mass values measured using the newly developed IMS(Bρ-IMS).We also studied the systematics of Coulomb displacement energies(CDEs)and found that anomalous staggering in CDEs was eliminated using new mass values.This method of T transformation is highly effective for conventional IMS equipped with a single time-of-flight detector.

Muscle Mass Is Associated with Depression in Adolescents and Young Adults

Background and Aims: The study aims to explore the association between body composition and depression in adolescents and young adults. Methods: A random cluster sampling method was used to select 41 age-matched indi-viduals (aged 11 - 30) as a non-depressive control group. The Department of Psychology at the Affiliated Hospital of Youjiang Medical University for Na-tionalities recruited 27 depressive patients within the same age range. Bioelec-trical impedance analysis measured body composition, while SCL-90, SAS, and SDS were employed for depression diagnosis. Logistic regression analysis was conducted to assess the relationship between body composition and de-pression scores. Results: The Depression Group exhibited higher levels of fat mass (p Conclusion: Depression is associated with age, gender, and muscle mass in adolescents and young people. Proper exercise and a healthy diet can increase muscle mass, thereby reducing fat mass and, as a result, reducing the prevalence of depression.

The Energy Origin of Mass

The concept of mass manifests in diverse forms, dimensions and configurations, and yet among all these manifestations, a unified origin is usually yearned for. This study aims to propose models that attribute the emergence of mass from fundamental quantities of physics, notably energy, space, and time. To this end, an operator is introduced, wherein these fundamental concepts serve as inputs, yielding functions that characterise mass. These functions are grounded in the domain of complex numbers, augmented by the incorporation of probabilistic elements, facilitating a nuanced depiction of mass modulation. Through investigation, it becomes apparent that a corollary energy field arises surrounding mass, facilitating its interactions within its surroundings. Ultimately, the comprehensive model of mass, inclusive of its associated field, gives rise to interactions with other masses, thereby engendering the genesis of larger and denser manifestations of mass, a phenomenon expounded within this framework.

Confining Potential and Mass of Elementary Particles

In this paper we consider a model in which the masses of elementary particles are formed and stabilized thanks to confining potential, which is caused by recoil momentum at emission of specific virtual bosons by particle itself. The calculation of this confining potential Ф(R) is carried out. It is shown that Ф(R) may be in the form const or const depending on continuous or discrete nature of the spectrum of emitted bosons.

Polarizable Additive with Intermediate Chelation Strength for Stable Aqueous Zinc‑Ion Batteries

Aqueous zinc-ion batteries are promising due to inherent safety,low cost,low toxicity,and high volumetric capacity.However,issues of dendrites and side reactions between zinc metal anode and the electrolyte need to be solved for extended storage and cycle life.Here,we proposed that an electrolyte additive with an intermediate chelation strength of zinc ion—strong enough to exclude water molecules from the zinc metal-electrolyte interface and not too strong to cause a significant energy barrier for zinc ion dissociation—can benefit the electrochemical stability by suppressing hydrogen evolution reaction,overpotential growth,and den-drite formation.Penta-sodium diethylene-triaminepentaacetic acid salt was selected for such a purpose.It has a suitable chelating ability in aqueous solutions to adjust solvation sheath and can be readily polarized under electrical loading conditions to further improve the passivation.Zn||Zn symmetric cells can be stably operated over 3500 h at 1 mA cm^(-2).Zn||NH4V4O10 full cells with the additive show great cycling stability with 84.6%capacity retention after 500 cycles at 1 A g^(-1).Since the additive not only reduces H2 evolution and corrosion but also modifies Zn2+diffusion and deposition,highlyreversible Zn electrodes can be achieved as verified by the experimental results.Our work offers a practical approach to the logical design of reliable electrolytes for high-performance aqueous batteries.

Tricuspid mass-curious case of Li-Fraumeni syndrome: A case report

BACKGROUND Li-Fraumeni syndrome(LFS)is a rare autosomal dominant cancer-predisposing syndrome,which can manifest as a polymorphic spectrum of malignancies.LFS is associated with an early onset in life,with the majority of cases occurring prior to the age of 46.Notwithstanding the infrequency of primary cardiac tumors,it behooves clinicians to remain vigilant in considering the differential diagnosis of such tumors in LFS patients who present with a cardiac mass.This is due to the markedly elevated risk for malignancy in this particular population,far surpassing that of the general populace.CASE SUMMARY Herein,we present a case of a 30-year-old female with LFS who was found to have a tricuspid valve leaflet mass.CONCLUSION This case exemplifies valuable learning points in the diagnostic approach for this exceptionally rare patient population.

Rationally designing electrolyte additives for highly improving cyclability of LiNi_(0.5)Mn_(1.5)O_(4)/Graphite cells

High voltage is necessary for high energy lithium-ion batteries but difficult to achieve because of the highly deteriorated cyclability of the batteries.A novel strategy is developed to extend cyclability of a high voltage lithium-ion battery,LiNi_(0.5)Mn_(1.5)O_(4)/Graphite(LNMO/Graphite)cell,which emphasizes a rational design of an electrolyte additive that can effectively construct protective interphases on anode and cathode and highly eliminate the effect of hydrogen fluoride(HF).5-Trifluoromethylpyridine-trime thyl lithium borate(LTFMP-TMB),is synthesized,featuring with multi-functionalities.Its anion TFMPTMB-tends to be enriched on cathode and can be preferentially oxidized yielding TMB and radical TFMP-.Both TMB and radical TFMP can combine HF and thus eliminate the detrimental effect of HF on cathode,while the TMB dragged on cathode thus takes a preferential oxidation and constructs a protective cathode interphase.On the other hand,LTFMP-TMB is preferentially reduced on anode and constructs a protective anode interphase.Consequently,a small amount of LTFMP-TMB(0.2%)in 1.0 M LiPF6in EC/DEC/EMC(3/2/5,wt%)results in a highly improved cyclability of LNMO/Graphite cell,with the capacity retention enhanced from 52%to 80%after 150 cycles at 0.5 C between 3.5 and 4.8 V.The as-developed strategy provides a model of designing electrolyte additives for improving cyclability of high voltage batteries.

Additive manufacturing of micropatterned functional surfaces:a review

Over the course of millions of years,nature has evolved to ensure survival and presents us with a myriad of functional surfaces and structures that can boast high efficiency,multifunctionality,and sustainability.What makes these surfaces particularly practical and effective is the intricate micropatterning that enables selective interactions with microstructures.Most of these structures have been realized in the laboratory environment using numerous fabrication techniques by tailoring specific surface properties.Of the available manufacturing methods,additive manufacturing(AM)has created opportunities for fabricating these structures as the complex architectures of the naturally occurring microstructures far exceed the traditional ways.This paper presents a concise overview of the fundamentals of such patterned microstructured surfaces,their fabrication techniques,and diverse applications.A comprehensive evaluation of micro fabrication methods is conducted,delving into their respective strengths and limitations.Greater emphasis is placed on AM processes like inkjet printing and micro digital light projection printing due to the intrinsic advantages of these processes to additively fabricate high resolution structures with high fidelity and precision.The paper explores the various advancements in these processes in relation to their use in microfabrication and also presents the recent trends in applications like the fabrication of microlens arrays,microneedles,and tissue scaffolds.

Advances and challenges in direct additive manufacturing of dense ceramic oxides

Ceramic oxides,renowned for their exceptional combination of mechanical,thermal,and chemical properties,are indispensable in numerous crucial applications across diverse engineering fields.However,conventional manufacturing methods frequently grapple with limitations,such as challenges in shaping intricate geometries,extended processing durations,elevated porosity,and substantial shrinkage deformations.Direct additive manufacturing(dAM)technology stands out as a state-of-the-art solution for ceramic oxides production.It facilitates the one-step fabrication of high-performance,intricately designed components characterized by dense structures.Importantly,dAM eliminates the necessity for post-heat treatments,streamlining the manufacturing process and enhancing overall efficiency.This study undertakes a comprehensive review of recent developments in dAM for ceramic oxides,with a specific emphasis on the laser powder bed fusion and laser directed energy deposition techniques.A thorough investigation is conducted into the shaping quality,microstructure,and properties of diverse ceramic oxides produced through dAM.Critical examination is given to key aspects including feedstock preparation,laser-material coupling,formation and control of defects,in-situ monitoring and simulation.This paper concludes by outlining future trends and potential breakthrough directions,taking into account current gaps in this rapidly evolving field.

Interface engineering strategy via electron-defect trimethyl borate additive toward 4.7 V ultrahigh-nickel LiNi_(0.9)Co_(0.05)Mn_(0.05)O_(2)battery

The Li metal battery with ultrahigh-nickel cathode(LiNi_(x)M_(1-x)O_(2),M=Mn,Co,and x≥0.9)under high-voltage is regarded as one of the most promising approaches to fulfill the ambitious target of 400 Wh/kg.However,the practical application is impeded by the instability of electrode/electrolyte interface and Ni-rich cathode itself.Herein we proposed an electron-defect electrolyte additive trimethyl borate(TMB)which is paired with the commercial carbonate electrolyte to construct highly conductive fluorine-and boron-rich cathode electrolyte interface(CEI)on LiNi_(0.9)Co_(0.05)Mn_(0.05)O_(2)(NCM90)surface and solid electrolyte interphase(SEI)on lithium metal surface.The modified CEI effectively mitigates the structural transformation from layered to disordered rock-salt phase,and consequently alleviate the dissolution of transition metal ions(TMs)and its“cross-talk”effect,while the enhanced SEI enables stable lithium plating/striping and thus demonstrated good compatibility between electrolyte and lithium metal anode.As a result,the common electrolyte with 1 wt%TMB enables 4.7 V NCM90/Li cell cycle stably over 100 cycles with 70%capacity retention.This work highlights the significance of the electron-defect boron compounds for designing desirable interfacial chemistries to achieve high performance NCM90/Li battery under high voltage operation.

ZnO Additive Boosts Charging Speed and Cycling Stability of Electrolytic Zn–Mn Batteries

Electrolytic aqueous zinc-manganese(Zn–Mn) batteries have the advantage of high discharge voltage and high capacity due to two-electron reactions. However, the pitfall of electrolytic Zn–Mn batteries is the sluggish deposition reaction kinetics of manganese oxide during the charge process and short cycle life. We show that, incorporating ZnO electrolyte additive can form a neutral and highly viscous gel-like electrolyte and render a new form of electrolytic Zn–Mn batteries with significantly improved charging capabilities. Specifically, the ZnO gel-like electrolyte activates the zinc sulfate hydroxide hydrate assisted Mn^(2+) deposition reaction and induces phase and structure change of the deposited manganese oxide(Zn_(2)Mn_(3)O_8·H_(2)O nanorods array), resulting in a significant enhancement of the charge capability and discharge efficiency. The charge capacity increases to 2.5 mAh cm^(-2) after 1 h constant-voltage charging at 2.0 V vs. Zn/Zn^(2+), and the capacity can retain for up to 2000 cycles with negligible attenuation. This research lays the foundation for the advancement of electrolytic Zn–Mn batteries with enhanced charging capability.

Toluene Processed All-Polymer Solar Cells with 18%Efficiency and Enhanced Stability Enabled by Solid Additive:Comparison Between Sequential-Processing and Blend-Casting

The emergence of polymerized small molecule acceptors(PSMAs)has significantly improved the performance of all-polymer solar cells(all-PSCs).However,the pace of device engineering lacks behind that of materials development,so that a majority of the PSMAs have not fulfilled their potentials.Furthermore,most high-performance all-PSCs rely on the use of chloroform as the processing solvent.For instance,the recent highperformance PSMA,named PJ1-γ,with high LUMO,and HOMO levels,could only achieve a PCE of 16.1%with a high-energy-level donor(JD40)using chloroform.Herein,we present a methodology combining sequential processing(SqP)with the addition of 0.5%wt PC_(71)BM as a solid additive(SA)to achieve an impressive efficiency of 18.0%for all-PSCs processed from toluene,an aromatic hydrocarbon solvent.Compared to the conventional blend-casting(BC)method whose best efficiency(16.7%)could only be achieved using chloroform,the SqP method significantly boosted the device efficiency using toluene as the processing solvent.In addition,the donor we employ is the classic PM6 that has deeper energy levels than JD40,which provides low energy loss for the device.We compare the results with another PSMA(PYF-T-o)with the same method.Finally,an improved photostability of the SqP devices with the incorporation of SA is demonstrated.

A facile strategy for tuning the density of surface-grafted biomolecules for melt extrusion-based additive manufacturing applications

Melt extrusion-based additive manufacturing(ME-AM)is a promising technique to fabricate porous scaffolds for tissue engi-neering applications.However,most synthetic semicrystalline polymers do not possess the intrinsic biological activity required to control cell fate.Grafting of biomolecules on polymeric surfaces of AM scaffolds enhances the bioactivity of a construct;however,there are limited strategies available to control the surface density.Here,we report a strategy to tune the surface density of bioactive groups by blending a low molecular weight poly(ε-caprolactone)5k(PCL5k)containing orthogonally reactive azide groups with an unfunctionalized high molecular weight PCL75k at different ratios.Stable porous three-dimensional(3D)scaf-folds were then fabricated using a high weight percentage(75 wt.%)of the low molecular weight PCL 5k.As a proof-of-concept test,we prepared films of three different mass ratios of low and high molecular weight polymers with a thermopress and reacted with an alkynated fluorescent model compound on the surface,yielding a density of 201-561 pmol/cm^(2).Subsequently,a bone morphogenetic protein 2(BMP-2)-derived peptide was grafted onto the films comprising different blend compositions,and the effect of peptide surface density on the osteogenic differentiation of human mesenchymal stromal cells(hMSCs)was assessed.After two weeks of culturing in a basic medium,cells expressed higher levels of BMP receptor II(BMPRII)on films with the conjugated peptide.In addition,we found that alkaline phosphatase activity was only significantly enhanced on films contain-ing the highest peptide density(i.e.,561 pmol/cm^(2)),indicating the importance of the surface density.Taken together,these results emphasize that the density of surface peptides on cell differentiation must be considered at the cell-material interface.Moreover,we have presented a viable strategy for ME-AM community that desires to tune the bulk and surface functionality via blending of(modified)polymers.Furthermore,the use of alkyne-azide“click”chemistry enables spatial control over bioconjugation of many tissue-specific moieties,making this approach a versatile strategy for tissue engineering applications.

Evaluation of slope stability through rock mass classification and kinematic analysis of some major slopes along NH-1A from Ramban to Banihal, North Western Himalayas

The network of Himalayan roadways and highways connects some remote regions of valleys or hill slopes,which is vital for India’s socio-economic growth.Due to natural and artificial factors,frequency of slope instabilities along the networks has been increasing over last few decades.Assessment of stability of natural and artificial slopes due to construction of these connecting road networks is significant in safely executing these roads throughout the year.Several rock mass classification methods are generally used to assess the strength and deformability of rock mass.This study assesses slope stability along the NH-1A of Ramban district of North Western Himalayas.Various structurally and non-structurally controlled rock mass classification systems have been applied to assess the stability conditions of 14 slopes.For evaluating the stability of these slopes,kinematic analysis was performed along with geological strength index(GSI),rock mass rating(RMR),continuous slope mass rating(CoSMR),slope mass rating(SMR),and Q-slope in the present study.The SMR gives three slopes as completely unstable while CoSMR suggests four slopes as completely unstable.The stability of all slopes was also analyzed using a design chart under dynamic and static conditions by slope stability rating(SSR)for the factor of safety(FoS)of 1.2 and 1 respectively.Q-slope with probability of failure(PoF)1%gives two slopes as stable slopes.Stable slope angle has been determined based on the Q-slope safe angle equation and SSR design chart based on the FoS.The value ranges given by different empirical classifications were RMR(37-74),GSI(27.3-58.5),SMR(11-59),and CoSMR(3.39-74.56).Good relationship was found among RMR&SSR and RMR&GSI with correlation coefficient(R 2)value of 0.815 and 0.6866,respectively.Lastly,a comparative stability of all these slopes based on the above classification has been performed to identify the most critical slope along this road.