Thermal Behavior and Crystal Transition of Biodegradable Poly(butylenes adipate)Revealed by Two-Dimensional Correlation Spectroscopy

In the present study,thermal behavior and crystal transition of pure poly(butylene adipate)(PBA)upon heating process were investigated by FTIR spectroscopy.To gain further insight into the thermal behavior alteration and the phase transition of PBA,we performed two-dimensional(2D)correlation analysis.We found thatβ-form PBA crystal undergoes not only the melting process but also crystal transition upon the heating process.

Thermal-oxidation mechanism of dioctyl adipate base oil

The ester base oil of dioctyl adipate (DOA) was oxidized in an oven at 200 degrees C for 30 h, and variations in the physicochemical and tribological properties were studied. To investigate the thermal-oxidation mechanism, the thermal-oxidation products were analyzed by gas chromatography-mass spectrometry (GC-MS), and the thermal-oxidation process was simulated using visual reactive force field molecular dynamics (ReaxFF MD). The results indicated that the total acid number (TAN) increased significantly because of the presence of 14% carboxylic acids and low molecular weight monoesters. The tribological properties were improved by the formation of the strongly polar carboxylic acids. Additionally, the increase in kinematic viscosity was limited due to the formation of high molecular weight polymerization products and low molecular weight degradation products. Thermal-oxidative degradation and polymerization mechanisms were proposed by combining ReaxFF MD simulations and GC-MS results.

Effects of Crystallization Temperature and Blend Ratio on the Crystal Structure of Poly(butylene adipate) in the Poly(butylene adipate)/Poly(butylene succinate) Blends

The effects of crystallization temperature and blend ratio on the polymorphic crystal structures of poly（butylene adipate） （PBA） in poly（butylene succinate） （PBS）/poly（butylene adipate） （PBS/PBA） blends were studied by means of differential scanning calorimetry （DSC）, wide-angle X-ray diffraction （XRD） and atomic force microscopy （AFM）. It was revealed that the polymorphism of PBA can be regulated by the blend ratio even in a non-isothermal crystallization process. The results demonstrate that high temperature favors fiat-on α crystals, while low temperature contributes to edge-on β crystals. It was also found that the effect of blend ratio on the crystallization mechanism of PBA is well coincident with that of the crystallization temperature. The increment of PBS content in the PBS/PBA blend gives rise to more β-form crystals of PBA. For those PBS/PBA blends with low PBA content, the interlamellar phase segregation of PBA makes its molecular chains so difficult to diffuse from one isolated microdomain to another that high crystallization temperature and sufficiently long crystallization time will be required if the PBA α-type crystals are targeted.

Crystallization Behavior of Biodegradable Poly(ethylene adipate) Modulated by a Benign Nucleating Agent： Zinc Phenylphosphonate

Zinc phenylphosphonate （PPZn）, a benign and biocompatible nucleating agent, was prepared and incorporated into the biodegradable poly（ethylene adipate） （PEA） to investigate its effect on the crystallization behavior, crystallization kinetics and spherulite morphology of PEA. Upon addition of PPZn, the crystallization temperature and crystallinity of PEA in the non-isothermal crystallization process increased significantly. Analysis of crystallization kinetics by Avrami equation suggests that the crystallization time shortened greatly and crystallization rate increased markedly after addition of PPZn. In the presence of PPZn, the spherulite size decreased and spherulite density increased significantly. It suggests that PPZn is an efficient nucleating agent for the crystallization of PEA. The accelerated crystallization in the presence of PPZn is mainly attributed to the epitaxial nucleation of PEA crystals on the surface of PPZn crystals, that is, a perfect lattice matching between PEA crystal and PPZn crystal occurs.

Synthesis of dimethyl adipate from cyclopentanone and dimethyl carbonate over solid base catalysts

A facile route for the synthesis of dimethyl adipate （DAP） from cyclopentanone and dimethyl carbonate （DMC） in the pres- ence of solid base catalysts has been developed. It was found that the intermediate carbomethoxycyclopentanone （CMCP） was produced from cyclopentanone with DMC in the first step, and then CMCP was further converted to DAP by reacting with a methoxide group. The role of the basic catalysts can be mainly ascribed to the activation of cyclopentanone via the abstraction of a proton in the a-position by base sites, and solid bases with moderate strength, such as MgO, favor the formation of DAP.

INDUCED CRYSTALLIZATION BEHAVIOR OF POLY(ETHYLENE ADIPATE) BY HIGHLY ORIENTED POLYETHYLENE

The crystallization behavior of poly（ethylene adipate） （PEA） on highly oriented high-density polyethylene （PE） substrate both from solution and isotropic melt was studied by means of optical microscopy, differential scanning calorimetry, atomic force microscopy and electron diffraction. The results show that the PE influences the crystallization of PEA strongly, which results in an epitaxial growth of PEA with well ordered structure. At the boundary of the PE substrate, a transcrystalline PEA layer is observed. Fine structural observation illustrates that the PEA grows on the PE substrate in edge- on lamellae with fixed orientation. Electron diffraction demonstrates that the epitaxial organization of PEA on PE occurs with both polymer chains parallel, which leads to the （00l） PEA diffractions inclined ±23.5° to the chain direction of PE crystals. Combining the real space morphological observation and electron diffraction results, it is concluded that the epitaxial PEA edge-on lamellae are folded in the {00l} lattice planes.

Crystallization Kinetics and Morphology of Poly(vinylidene fluoride)/Poly(ethylene adipate) Blends

The miscibility, isothermal crystallization kinetics and morphology of the poly（vinylidene fluoride）（PVDF）/poly（ethylene adipate）（PEA） blends have been studied by differential scanning calorimetry（DSC）, optical microscopy（OM） and scanning electron microscopy（SEM）. A depression of the equilibrium melting point of PVDF was observed. From the melting point data of PVDF, a negative but quite small value of the interaction parameter ？PVDF-PEA is derived using the Flory-Huggins equation, implying that PVDF shows miscibility with PEA to some extent. Nonisothermal and isothermal crystallization kinetics suggest that the crystallization rate of PVDF decreases with increasing the amount of PEA, and a contrary trend was found when PEA crystallizes with the increase of the amount of PVDF. It was further disclosed that the blend ratio and crystallization temperature affect the texture of PVDF spherulites greatly, which determines the subsequent crystallization of PEA. At high temperatures, e.g. 150 ℃, the band spacing of PVDF spherulites increases with the addition of PEA content and the spherulitic structure becomes more open. In this case, spherulitic crystallization of PEA is not observed for all blend compositions. At low temperatures, e.g. 130 ℃, for the PEA-rich blends, the interpenetrated structures are eventually formed by the penetration of the spherulites of PEA growing within the pre-existing PVDF spherulites.

Influence of Teflon Substrate on Crystallization and Enzymatic Degradation of Polymorphic Poly(butylene adipate)

Oriented and non-oriented Teflon films, which were found to have the same crystalline structure, but different surface morphologies, were used to sandwich poly（butylene adipate） （PBA） films during isothermal crystallization. It was found that both the Teflon surface structure and the PBA polymorphic structure are the determining factors to induce epitaxial crystallization. The oriented Teflon film was able to induce epitaxial crystallization of PBA α crystal, while the non-oriented Teflon did not induce any epitaxial crystallization of PBA. Epitaxial crystallization did not occurred for PBA β crystals between neither the oriented nor the non-oriented Teflon films. The enzymatic degradation rate of PBA films was not determined by the epitaxial crystallization, in fact it was still dependent on the polymorphic crystal structure of PBA. The morphological changes of PBA films after enzymatic degradation confirmed again that the epitaxial crystallization only occurred for the PBA film with α crystal structure which was produced by being sandwiched between oriented Teflon films, and it happened only on the surface of PBA films.

Crystallization of Poly(ethylene adipate) within γ-Phase Poly(vinylidene fluoride) Matrix

The effects of PEA on the ）γ-phase PVDF crystal structure and the crystallization of PEA within the pre-existing γ-phase PVDF spherulites have been investigated by optical microscopy （OM）, infrared spectroscopy （IR） and scanning electron microscopy （SEM）. The results demonstrate that the γ-phase PVDF spherulites consist of the lamellae exhibiting a highly curved scroll-like morphology and develop preferentially in PEA-rich blend. With increasing PEA concentration, the scroll diameter increases and the scrolls are better separated from each other. PEA crystallizes first in the interspherulitic region and transcrystalline layer develops. Subsequently, the transcrystalline layer of PEA continues to grow within theγ-phase PVDF spherulites, e.g., in the region between the scrolls, until impinging on other PEA transcrystalline layers or spherulites. The crystallization kinetics results indicate that the growth rate of PEA crystals in the intraspherulitic region of γ-phase PVDF shows a positive correlation with content of PEA, but a negative one with the crystallization temperature of γ-phase PVDF.

Generation of Tough Poly(glycolic acid)(PGA)/Poly(butylene succinate-co-butylene adipate)(PBSA)Films with High Gas Barrier Performance through In situ Nanofibrillation of PBSA under an Elongational Flow Field

Poly(glycolic acid)(PGA)is derived from glycolide obtained by fermenting pineapples or sugarcane,which has excellent gas barrier properties and a small carbon footprint.PGA is a potential substitute for the current aluminum-plastic composite films used in high barrier packaging applications.However,its poor ductility and narrow processing window limit its application in food packaging.Herein,poly(butylene succinate-co-butylene adipate)(PBSA)was used to fabricate PGA/PBSA blend films through an in situ fibrillation technique and blown film extrusion.Under the elongational flow field used during the extrusion process,a unique hierarchical structure based on the PBSA nanofibrils and interfacially oriented PGA crystals was obtained.This structure enhances the strength,ductility and gas barrier properties of the PGA/PBSA blend film.In addition,an epoxy chain extender(ADR4468)was used as a compatibilizer to further enhance the interfacial adhesion between PGA and PBSA.70PGA/0.7ADR exhibited a very low oxygen permeability(2.34×10^(-4)Barrer)with significantly high elongating at break(604.4%),tensile strength(47.4 MPa),and transparency,which were superior to those of petroleum-based polymers.Thus,the 70PGA/0.7ADR blown films could satisfy the requirements for most instant foods such as coffee,peanuts,and fresh meat.

Prominently Promoting the Formation of Poly(butylene adipate) α-Form Crystals by Coalescing from Inclusion Complex

We successfully use a co-precipitation method to prepare inclusion complex between poly（butylene adipate） （PBA） chains （guest component） and urea molecules （host component）. The PBA/urea inclusion complex is confirmed to adopt a hexagonal crystal modification with lattice parameters ofa = 8.14 A and c = 10.92 A, and the interaction between PBA chains and urea is van der Waals force. The singly isolated PBA chains are suggested to take some gauche conformation, which is different from the all-trans conformation in r-form PBA. Furthermore, we employ the isolated PBA chains which are uniformly pre-established in a specific conformation in urea channels to regulate the crystal form of PBA for the first time. After removing the host urea molecules, the coalesced PBA chains are found to solely crystallize into a-form crystals at different coalescing temperatures. By comparing the FTIR spectra, it is found that PBA chains in inclusion complex plausibly contain some similar conformers as those in a-form crystal, which is suggested to be the intrinsic reason for the sole formation of a-form crystals. This research proves that inclusion complex can be used as a very effective method to regulate polymorphism of semi-crystalline polymers.

水体中邻苯二甲酸酯和己二酸酯的气相色谱-质谱分析方法

Phthalates and adipate ester in water have been extracted with n-hexane and analyzed by gas chromatography-mass spectrometry(GC-MS).The mean recoveries ranged from 69% to 109% with their RSD range of 1.96%-10.2%.The research results also showed that the method presented simplicity-operating,excellent linearity and reproducibility.

Study on the Synthesis and Biodegradation of Aliphatic Polyester

An aliphatic polyester, poly(hexalene adipate) (PHA) and an aliphatic copolyester, poly (hexalene adipate succinate) (PHAS) were synthesized by direct condensation of corresponding binary acid and binary alcohol in the presence of a catalyst, p-toluene sulfonic acid. The biodegradation of these polyesters were studied in the laboratory by enzyme attack and outdoor soil burial. The results show that these polyesters have good biodegradability and the copolyester PHAS, even displayed a better biodegradability than the polyester PHA. In the presence of Penicillium chrysogenum the weight loss reached 18.3% for the PHAS (film thickness 1.0 mm) and 9.1% for the PHA (film thickness 1.0 mm) after 28 days. Outdoor soil burial tests indicate that these polyesters also have good biodegradability in natural conditions. The weight loss reached 14.2% for PHAS (film thickness 0.1 mm) and 6.7% for PHA (film thickness 0.1 mm) after burying in soil for 36 days.

Influence of adipic acid on anodic film formation and corrosion resistance of 2024 aluminum alloy

The influence of adipic acid on the formation and corrosion resistance of anodic oxide film fabricated on 2024 aluminum alloy was investigated. The morphology was investigated by scanning electron microscopy （SEM） and transmission electron microscopy （TEM）, respectively. The corrosion resistance was evaluated by electrochemical impedance spectroscopy （EIS）. The results showed that the adipic acid was absorbed at the electrolyte/anodic layer interface during anodizing. The corrosion rate of anodic film decreased and the film thickness increased. The film was uniform and compact especially at the film/substrate interface. After sealing procedure, anodic film formed with the addition of adipic acid exhibited improved dielectric property and corrosion resistance in aggressive environment.

环己酮绿色氧化合成己二酸质谱分析

己二酸是合成尼龙-66的主要原料,同时在低温润滑油、合成纤维、油漆、聚亚胺酯树脂及食品添加剂的制备等方面也有重要用途,目前己二酸的世界年产量估计已达220万吨.工业上己二酸的生产是以环己烷经两步氧化合成,第一步为环己烷在金属离子催化下用氧气氧化为环己醇、环己酮,第二步用浓HNO3氧化环己醇、环己酮制得己二酸.……

Simulation of Continuous Esterification Process of Polyester Polyols

Based on the kinetic and thermodynamic equations, a comprehensive mathematical model for the con- tinuous esterification process of polyester polyols was developed, which was carried out in an innovational bub- bling reactive distillation tower （BRDT） at atmospheric pressure. In this new type of reactor, direct esterification between ethylene glycol and adipic acid was accomplished efficiently and rapidly. A bench BRDT with the height of 2 m was applied for the esteriflcation process of l^oly （ethylene adlpate） （P＇EA）. In the continuous operation, Hn- ear oligomers were discharged from the bottom of the column, while water passed a few column trays and a pack- ing section as a condensation byproduct. The influence of major operating conditions on reactor performance was also simulated. Simulation results were in good agreement with experimental data, providing a strategy for devel- oping and optimizing this process.

Enzyme-Mediated Enantioselective Hydrolysis of Aliphatic Dicarboxylic Acid Diesters

The enzyme-mediated highly enantioselective hydrolysis of aliphatic dicarboxylic acid diesters has been developed. The racemic diesters were easily prepared by the coupling of racemic alcohols with dicarboxylic anhydrides followed by esterification or with dicarboxylic acids. In the cases of bis(1-phenylethyl) glutarate and bis(1-phenylethyl) adipate, the diesters which contained the dl- and meso-form diastereomers, were enantioselectively hydrolyzed by lipase from Candida antarctica (Novozym 435) in buffer at 30°C to afford the almost optically pure (R)-1-phenylethanol. On the other hand, the following chemical hydrolysis of the remaining (S, S)-diesters and (S)-monoesters gave the (S)-alcohol. Finally, both enantiomers were stoichiometrically obtained in about 100% isolated yield based on the racemic diesters. The enzymatic reaction was also applicable for the preparation of several optically active alcohols. In some cases, both the reactivities and enantioselectivities were quite different from those in the case of the corresponding simple acetates.

Measurement and Correlation for Solubility of Adipic Acid in Several Solvents

Using a laser detecting system, solubility data were measured for adipic acid dissolved in six pure solvents, namely, cyclohexanone, cyclohexanol, acetic acid, N,N-dimethylformamide, N,N-dimethylacetamide, and dimethylsulfoxide at the temperature range from 293.15K to 353.15K. All these data were regressed by 2h, NRTL, Wilson, and the modified Wilson models. For the study of six, 2h, NRTL, and the modified Wilson models were found to provide an accurate mathematical representation of the experimental results, with overall average absolute relative deviations between measured and calculated values as 1.74%, 2.06%, and 3.06%, respectively. The results showed that the λh model is the most suitable for description of the solid-liquid equilibrium containing adipic acid.

Measurement and Correlation of Solubilities of Adipic Acid in Different Solvents

Using a simple and reliable apparatus, the solubilities of adipic acid in water, ethanol, chloroform, n-butanol and acetone are determined by the analytic method. The results are correlated with λh equation, Apelblat equation, and UNIFAC equation. The solubilities calculated by these models are in good agreement with experi-mental data, so that the models can meet the requirements of engineering design.

Recent advances on controllable and selective catalytic oxidation of cyclohexene

Because of multiple potential reaction sites and variable oxidation depths,oxidation of cyclohexene can lead to a mixture of products with different oxidation states and functional groups,such as 7-oxabicyclo[4.1.0]heptane,trans/cis-cyclohexane-1,2-diol,cyclohex-2-en-1-ol,cyclohex-2-en-1-one,and even adipic acid.These products are broadly and abundantly used intermediates in the chemical industry;therefore,controllable oxidation reactions for cyclohexene that can selectively afford the targeted products are synthetically valuable for applications in both the academy and industry,thus becoming the aim of synthetic and catalytic chemists in the field.Many reports on selective oxidation of cyclohexene have recently appeared in the literature because of its significance.This short review summarizes the recent advances on this subject,and the contents are mainly classified based on the chosen oxidants.We hope that this review can provide a useful guide for controllable and selective catalytic oxidation of cyclohexene for interested readers from both the academy and industry.