PREPARATION AND ADSORBABILITY OF DEXTRAN MICROSPHERES WITH UNIFORM DIAMETER

The method of preparing uniform dextran microspheres with a narrow diameter distribution was introduced and the adsorbability of these microspheres was evaluated.The microspheres were prepared in W/O microemulsion using 0.5% dextran solution as the aqueous phase and n-hexane as the oil phase.Characteristics of the prepared dextran microspheres were examined with laser light blocking technique,optical microscope and ultraviolet spectrometer.The results show that the prepared dextran microspheres have uniform morphology and narrow diameter distribution,nearly 92% of them having a diameter of 56.6 μm.In vitro evaluation of adsorbability,wet dextran microspheres have good adsorption of 98.32 mg/g of model drug methylene blue in 20.86 mg/L methylene blue solution at 25℃.The adsorption of dried dextran microspheres under the same condition is 132.15 mg/g,which is even higher.And the adsorbability of dextran microspheres has significant relationship with the concentration of methylene blue and temperature.The adsorbability is better at lower temperature and higher concentration of methylene blue.

A green cross-linking method for the preparation of renewable threedimensional graphene sponges for efficient adsorption of Congo red dye

Graphene-based materials possess significant potential for the treatment of dye wastewater due to their exceptional adsorption properties toward stubborn pollutants.However,their utilization is hindered by high preparation costs,low yields,environmental pollution during synthesis,and challenges in regenerating the adsorbent.This study proposes a novel approach to address these limitations by developing nitrogen-doped three-dimensional(3D)polyvinyl alcohol(PVA)crosslinked graphene sponges(N-PGA)using a cross-linking method with ammonium carbonate.This method offers a relatively mild,environmentally friendly approach.Ammonium carbonate serves as both a reducing and modifying agent,facilitating the formation of the intrinsic structure of N-PGA and acting as a nitrogen source.Meanwhile,PVA is utilized as the cross-linking agent.The results demonstrate that N-PGA exhibits a favorable internal 3D hierarchical porous structure and possesses robust mechanical properties.The measured specific surface area(BET)of N-PGA was as high as406.538 m^(2)·g^(-1),which was favorable for its efficient adsorption of Congo red(CR)dye molecules.At an initial concentration of 50 mg·L^(-1),N-PGA achieved an impressive removal rate of 89.6%and an adsorption capacity of 112 mg·g^(-1)for CR dye.Furthermore,it retained 79%of its initial adsorption capacity after 10 cycles,demonstrating excellent regeneration performance.In summary,the synthesized N-PGA displays remarkable efficacy in the adsorption of CR dye in wastewater,opening up new possibilities for utilizing 3D porous graphene nanomaterials as efficient adsorbents in wastewater treatment.

Few-layered hexagonal boron nitride nanosheets stabilized Pt NPs for oxidation promoted adsorptive desulfurization of fuel oil

A few-layered hexagonal boron nitride nanosheets stabilized platinum nanoparticles(Pt/h-BNNS)is engineered for oxidation-promoted adsorptive desulfurization(OPADS)of fuel oil.It was found that the few-layered structure and the defective sites of h-BNNS not only are beneficial to the stabilization of Pt NPs but also favor the adsorption of aromatic sulfides.By employing Pt/h-BNNS with a Pt loading amount of 1.19 wt%as the active adsorbent and air as an oxidant,a 98.0%sulfur removal over dibenzothiophene(DBT)is achieved along with a total conversion of the DBT to the corresponding sulfones(DBTO_(2)).Detailed experiments show that the excellent desulfurization activity originates from the few-layered structure of h-BNNS and the high catalytic activity of Pt NPs.In addition,the OPADS system with Pt/h-BNNS as the active adsorbent shows remarkable stability in desulfurization performance with the existence of different interferents such as olefin,and aromatic hydrocarbons.Besides,the Pt/h-BNNS can be recycled 12 times without a significant decrease in desulfurization performance.Also,a process flow diagram is proposed for deep desulfurization of fuel oil and recovery of high value-added products,which would promote the industrial application of such OPADS strategy.

Boosting kinetic separation of ethylene and ethane on microporous materials via crystal size control

The adsorptive separation of C_(2)H_(4)and C_(2)H_(6),as an alternative to distillation units consuming high energy,is a promising yet challenging research.The great similarity in the molecular size of C_(2)H_(4)and C_(2)H_(6)brings challenges to the regulation of adsorbents to realize efficient dynamic separation.Herein,we reported the enhancement of the kinetic separation of C_(2)H_(4)/C_(2)H_(6)by controlling the crystal size of ZnAtzPO_(4)(Atz=3-amino-1,2,4-triazole)to amplify the diffusion difference of C_(2)H_(4)and C_(2)H_(6).Through adjusting the synthesis temperature,reactant concentration,and ligands/metal ions molar ratio,ZnAtzPO4 crystals with different sizes were obtained.Both single-component kinetic adsorption tests and binary-component dynamic breakthrough experiments confirmed the enhancement of the dynamic separation of C_(2)H_(4)/C_(2)H_(6)with the increase in the crystal size of ZnAtzPO_(4).The separation selectivity of C_(2)H_(4)/C_(2)H_(6)increased from 1.3 to 98.5 with the increase in the crystal size of ZnAtzPO_(4).This work demonstrated the role of morphology and size control of adsorbent crystals in the improvement of the C_(2)H_(4)/C_(2)H_(6)kinetic separation performance.

Deciphering the linear relationship in the activity of the oxygen reduction reaction on Pt electrodes:A decisive role of adsorbates

Despite substantial efforts in developing high-performance catalysts for the oxygen reduction reaction(ORR),the persistent challenge lies in the high onset overpotential of the ORR,and the effect of the elec-trolyte solution cannot be ignored.Consequently,we have systematically investigated the impact of adsorbate species and concentration,as well as solution pH,on the ORR activity on Pt(111)and Pt(poly)electrodes.The results all tend to establish a linear quantitative relationship between the onset potential for ORR and the adsorption equilibrium potential of the adsorbate.This finding indicates the decisive role of adsorbates in the onset potential for ORR,suggesting that the adsorption potential of adsorbates can serve as an intuitive criterion for ORR activity.Additional support for this conclusion is derived from experimental results obtained from the oxygen evolution reaction on Pt(poly)with different adsorbate species and from the hydrogen evolution reaction on Pt(111)with iodine adsorption.We further propose both an empirical equation for the onset potential for ORR and the concept of a potential-regulated adsor-bate shielding effect to elucidate the influence of adsorbates on ORR activity.This study provides new insights into the high onset overpotential of the ORR and offers potential strategies for predicting and enhancingORRactivity inthefuture.

Preparation of Manganese Oxide and Its Adsorption Properties

The in-situ oxidation of manganese sulfate solution with H2O_(2),sodium hypochlorite,potassium permanganate and oxygen as oxidants was investigated by means of SEM,EDS,XRD,BET and infrared analysis,and the effects of different oxidants on the morphology,phase composition,surface properties and specific surface area of manganese oxides were investigated.The experimental results show that the diameter of manganese oxide particles prepared with H_(2)O_(2)is the smallest,about 50 nm,and the specific surface area is the largest,63.8764 m^(2)/g.It has the advantages of abundant surface hydroxyl groups,no introduction of other impurities and large adsorption potential.It is most suitable to be used as an oxidant for oxidizing manganese sulfate solution to prepare manganese oxide by in-situ oxidation.Nano manganese oxide prepard by H_(2)O_(2)in-situ oxidation method is used as adsorbent to adsorb cobalt and nickel impurities in manganese sulfate.When the reaction pH is 6,the reaction time is 30min and the amount of adsorbent is 1.0 g,the adsorption rates of cobalt and nickel impurities in 100ml manganese sulfate solution are 97.59%and 97.67%,respectively.The residual amounts of cobalt and nickel meet the industrial process standard of first-class products(Co,Ni w/%≤0.005)of high-purity manganese sulfate(Hg/t4823-2015)for batteries.The study plays a guiding role in the preparation and regulation of manganese oxide,and provides a new method with high efficiency,purity and adsorbent availability for the preparation of high-purity manganese sulfate solution.

Efficient adsorption separation of methane from C_(2)-C_(3) hydrocarbons in a Co(Ⅱ)-nodes metal-organic framework

Methane(CH_(4))as a substitute for other mineral fuels plays a crucial role in reducing energy consumption and preventing environmental pollution.The present study employs a solvothermal method to fabricate a porous framework Co-metal-organic framework(Co-MOF)containing two distinct secondary building units(SBUs):an anionic[Co_(2)(μ_(2)-OH)(COO)_(4)(H_(2)O)]and a neutral[CoN_(2)(COO)_(2)].Notably,within the anionic SBUs,the coordinated water molecules induce the generation of divergent unsaturated Co(Ⅱ)centers in the unidirectional porous channels,thereby creating open metal sites.The adsorption performance of Co-MOF towards pure component gases was systematically investigated.The results demonstrated that Co-MOF exhibits superior adsorption capacity for C_(2)-C_(3) hydrocarbons compared to CH_(4),which offers the potential for efficient adsorption and separation of CH_(4) from C_(2)-C_(3) hydrocarbons.The gas selectivity separation ratios of Co-MOF for C_(2)H_(6)/CH_(4) and C_(3)H_8/CH_(4) were calculated using the ideal adsorbed solution theory method at 273/298 K and 0.1 MPa.The results revealed that Co-MOF achieved remarkable equilibrium separation selectivity for CH_(4) and C_(2)-C_(3) hydrocarbon gases among non-modified MOFs,signifying the potential of the synthesized Co-MOF for efficient recovery and purification of CH_(4) from C_(2)-C_(3) hydrocarbons.Breakthrough experiments further demonstrate the ability of Co-MOF to purify methane from C_(2)-C_(3) hydrocarbons in practical gas separation scenarios.Additionally,molecular simulation calculations further substantiate the propensity of anionic SBUs to interact with C_(2)-C_(3) hydrocarbon compounds.This study provides a novel paradigm for the development of porous MOF materials in the application of gas mixture separation.

High adsorption selectivity of activated carbon and carbon molecular sieve boosting CO_(2)/N_(2) and CH_(4)/N_(2) separation

Flue gas and coal bed methane are two important sources of greenhouse gases.Pressure swing adsorption process has a wide range of application in the field of gas separation,and the selection of adsorbent is crucial.In this regard,in order to assess the better adsorbent for separating CO_(2) from flue gas and CH_(4) from coal bed methane,adsorption isotherms of CO_(2),CH_(4) and N_(2) on activated carbon and carbon molecular sieve are measured at 303.15,318.15 and 333.15 K,and up to 250 kPa.The experimental data fit better with Langmuir 2 compared to Langmuir 3 and Langmuir-Freundlich models,and Clausius-Clapeyron equation was used to calculate the isosteric heat.Both the order of the adsorbed amount and the adsorption heat on the two adsorbents are CO_(2)>CH_(4)>N_(2).The adsorption kinetics are calculated by the pseudo-first kinetic model,and the order of adsorption rates on activated carbon is N_(2)-CH_(4)>CO_(2),while on carbon molecular sieve,it is CO_(2)-N_(2)>CH_(4).It is shown that relative molecular mass and adsorption heat are the primary effect on kinetics for activated carbon,while kinetic diameter is the main resistance factor for carbon molecular sieve.Moreover,the adsorption selectivity of CH_(4)/N_(2) and CO_(2)/N_(2) were estimated with the ideal adsorption solution theory,and carbon molecular sieve performed best at 318.15 K for both CO_(2) and CH_(4) separation.The study suggested that activated carbon is a better choice for separating flue gas and carbon molecular sieve can be a strong candidate for separating coal bed methane.

Antagonism effect of residual S triggers the dual-path mechanism for water oxidation

Transition metal chalcogenides(TMCs)are recognized as pre-catalysts,and their(oxy)hydroxides derived from electrochemical reconstruction are the active species in the water oxidation.However,understanding the role of the residual chalcogen in the reconstructed layer is lacking in detail,and the corresponding catalytic mechanism remains controversial.Here,taking Cu_(1-x)Co_(x)S as a platform,we explore the regulating effect and existence form of the residual S doped into the reconstructive layer for oxygen evolution reaction(OER),where a dual-path OER mechanism is proposed.First-principles calculations and operando~(18)O isotopic labeling experiments jointly reveal that the residual S in the reconstructive layer of Cu_(1-x)Co_(x)S can wisely balance the adsorbate evolution mechanism(AEM)and lattice oxygen oxidation mechanism(LOM)by activating lattice oxygen and optimizing the adsorption/desorption behaviors at metal active sites,rather than change the reaction mechanism from AEM to LOM.Following such a dual-path OER mechanism,Cu_(0.4)Co_(0.6)S-derived Cu_(0.4)Co_(0.6)OSH not only overcomes the restriction of linear scaling relationship in AEM,but also avoids the structural collapse caused by lattice oxygen migration in LOM,so as to greatly reduce the OER potential and improved stability.

3D printing of poly(ethyleneimine)-functionalized Mg-Al mixed metal oxide monoliths for direct air capture of CO_(2)

Direct air capture(DAC)of CO_(2)plays an indispensable role in achieving carbon-neutral goals as one of the key negative emission technologies.Since large air flows are required to capture the ultradilute CO_(2)from the air,lab-synthesized adsorbents in powder form may cause unacceptable gas pressure drops and poor heat and mass transfer efficiencies.A structured adsorbent is essential for the implementation of gas-solid contactors for cost-and energy-efficient DAC systems.In this study,efficient adsorbent poly(ethyleneimine)(PEI)-functionalized Mg-Al-CO_(3)layered double hydroxide(LDH)-derived mixed metal oxides(MMOs)are three-dimensional(3D)printed into monoliths for the first time with more than 90%adsorbent loadings.The printing process has been optimized by initially printing the LDH powder into monoliths followed by calcination into MMO monoliths.This structure exhibits a 32.7%higher specific surface area and a 46.1%higher pore volume,as compared to the direct printing of the MMO powder into a monolith.After impregnation of PEI,the monolith demonstrates a large adsorption capacity(1.82 mmol/g)and fast kinetics(0.7 mmol/g/h)using a CO_(2)feed gas at 400 ppm at 25℃,one of the highest values among the shaped DAC adsorbents.Smearing of the amino-polymers during the post-printing process affects the diffusion of CO_(2),resulting in slower adsorption kinetics of pre-impregnation monoliths compared to post-impregnation monoliths.The optimal PEI/MeOH ratio for the post-impregnation solution prevents pores clogging that would affect both adsorption capacity and kinetics.

Coal-rock gas:Concept,connotation and classification criteria

In recent years,great breakthroughs have been made in the exploration and development of natural gas in deep coal-rock reservoirs in Junggar,Ordos and other basins in China.In view of the inconsistency between the industrial and academic circles on this new type of unconventional natural gas,this paper defines the concept of"coal-rock gas"on the basis of previous studies,and systematically analyzes its characteristics of occurrence state,transport and storage form,differential accumulation,and development law.Coal-rock gas,geologically unlike coalbed methane in the traditional sense,occurs in both free and adsorbed states,with free state in abundance.It is generated and stored in the same set of rocks through short distance migration,occasionally with the accumulation from other sources.Moreover,coal rock develops cleat fractures,and the free gas accumulates differentially.The coal-rock gas reservoirs deeper than 2000 m are high in pressure,temperature,gas content,gas saturation,and free-gas content.In terms of development,similar to shale gas and tight gas,coal-rock gas can be exploited by natural formation energy after the reservoirs connectivity is improved artificially,that is,the adsorbed gas is desorbed due to pressure drop after the high-potential free gas is recovered,so that the free gas and adsorbed gas are produced in succession for a long term without water drainage for pressure drop.According to buried depth,coal rank,pressure coefficient,reserves scale,reserves abundance and gas well production,the classification criteria and reserves/resources estimation method of coal-rock gas are presented.It is preliminarily estimated that the coal-rock gas in place deeper than 2000 m in China exceeds 30×10^(12)m^(3),indicating an important strategic resource for the country.The Ordos,Sichuan,Junggar and Bohai Bay basins are favorable areas for large-scale enrichment of coal-rock gas.The paper summarizes the technical and management challenges and points out the research directions,laying a foundation for the management,exploration,and development of coal-rock gas in China.

Novel Cs-Mg-Al mixed oxide with improved mobility of oxygen species for passive NO_(x)adsorption

The development of passive NO_(x)adsorbers with cost-benefit and high NO_(x)storage capacity remains an on-going challenge to after-treatment technologies at lower temperatures associated with cold-start NO_(x)emissions.Herein,Cs_(1)Mg_(3)Al catalyst prepared by sol-gel method was cyclic tested in NO_(x)storage under 5 vol%water.At 100°C,the NO_(x)storage capacity(1219 μmol g^(-1))was much higher than that of Pt/BaO/Al_(2)O_(3)(610 μmol g^(-1)).This provided new insights for non-noble metal catalysts in low-temperature passive NO_(x)adsorption.The addition of Cs improved the mobility of oxygen species and thus improved the NO_(x)storage capacity.The XRD,XPS,IR spectra and in situ DRIFTs with NH3 probe showed an interaction between CsO_(x)and AlO_(x)sites via oxygen species formed on Cs_(1)Mg_(3)Al catalyst.The improved mobility of oxygen species inferred from O2-TPD was consistent with high NO_(x)storage capacity related to enhanced formation of nitrate and additional nitrite species by NO_(x)oxidation.Moreover,the addition of Mg might improve the stability of Cs_(1)Mg_(3)Al by stabilizing surface active oxygen species in cyclic experiments.

A functionalized activated carbon adsorbent prepared from waste amidoxime resin by modifying with H_(3)PO_(4) and ZnCl_(2) and its excellent Cr(Ⅵ)adsorption

With the application of resins in various fields, numerous waste resins that are difficult to treat have been produced. The industrial wastewater containing Cr(Ⅵ) has severely polluted soil and groundwater environments, thereby endangering human health. Therefore, in this paper, a novel functionalized mesoporous adsorbent PPR-Z was synthesized from waste amidoxime resin for adsorbing Cr(Ⅵ). The waste amidoxime resin was first modified with H3PO4 and ZnCl_(2), and subsequently, it was carbonized through slow thermal decomposition. The static adsorption of PPR-Z conforms to the pseudo-second-order kinetic model and Langmuir isotherm, indicating that the Cr(Ⅵ) adsorption by PPR-Z is mostly chemical adsorption and exhibits single-layer adsorption. The saturated adsorption capacity of the adsorbent for Cr(Ⅵ) could reach 255.86 mg/g. The adsorbent could effectively reduce Cr(Ⅵ) to Cr(Ⅲ) and decrease the toxicity of Cr(Ⅵ) during adsorption. PPR-Z exhibited Cr(Ⅵ) selectivity in electroplating wastewater. The main mechanisms involved in the Cr(Ⅵ) adsorption are the chemical reduction of Cr(Ⅵ) into Cr(Ⅲ) and electrostatic and coordination interactions. Preparation of PPR-Z not only solves the problem of waste resin treatment but also effectively controls Cr(Ⅵ) pollution and realizes the concept of “treating waste with waste”.

Effects of Papyrus Plants (Cyperus papyrus) on the Physicochemical Parameters and Nutrient Levels of Water and Sediments in Yala Swamp Wetland in Western Kenya

Yala swamp wetland is the largest fresh water wetland ecosystem in Kenya supporting a broad biodiversity. It comprises of River Yala, the Yala swamp, Lakes Kanyaboli, Namboyo and Sare, and a portion of Lake Victoria neighboring the swamp. Approximately 2300 ha of land have been reclaimed and has been used for large-scale agriculture resulting in mass destruction of papyrus to create room for framing. Papyrus are known to be important in phytoremediation but despite this role information is limited, lacks supportive evidence and the empirical aspect on the levels of these pollutants in relation to the papyrus biomass is limited. The study is aimed at determining the effects of Cyperus papyrus on the water and sediment quality in Yala Swamp wetland. Six sampling sites were purposefully selected to monitor the variations of the physicochemical parameters (temperature, dissolved oxygen: DO, pH, biological oxygen demand: BOD, total suspended solids: TSS, turbidity, electrical conductivity: EC and total dissolved solids: TSS) and the levels selected nutrients (phosphorus and nitrates) in water and sediments as River Yala flows through Dominion Farms, Lake Sare which surrounded by Cyperus papyrus and finally into Lake Victoria. The samples were collected in triplicates during the wet and dry seasons (May and September 2015 respectively). The physicochemical parameters were measured in situ using a Hydrolab muiltimeter while the nutrients were analyzed using UV/Vis spectroscopy. Statistical analysis was done using SAS V9.0 software. The mean temperature was 26.19˚C ± 0.71˚C, DO: 3.72 ± 1.02 Mg/l, BOD: 3.9 ± 0.32 Mg/l, pH: 7.52 ± 0.17, TDS: 109 ± 86.33, EC: 173.26 ± 13.8 μS/cm, TSS: 12.42 ± 18.51 Mg/l and Turbidity: 12.29 ± 10.03 NTU. The values varied significantly at P 0.05 among all the sites. The results show that papyrus is useful in maintaining the required levels of physicochemical parameters. The study will assist in conservation of the papyrus to help phytoremediate pollutants from Dominion farms and the adjacent farms in order to have ecologically sound wetland.

Adsorption Effect of Phosphate Modified Grape Branch Biochar on Cd2

Two major problems facing agriculture at present are soil pollution and the disposal of solid wastes generated during plant growth. The method of preparing biochar from solid wastes produced by plants is a means of maximizing the use of resources to combat the problem of soil pollution. In this study, we did not choose straw in the traditional sense but the waste branches from grape pruning, which has higher lignin cellulose, as the raw material. The biochar derived from grape branches pyrolyzed at 300˚C for two hours was utilized as a raw material to prepare modified biochar with varying concentrations of phosphoric acid. The adsorption performance and mechanism of Cd2 were explored through experiments involving different concentrations, addition amounts, reaction times, kinetic analyses, and isothermal adsorption tests. The findings indicated that the optimal adsorption of Cd2 occurred with a 20% phosphoric acid concentration, achieving the highest adsorption rate of 84.62%. At a dosage of 10 g/L, the maximum adsorption capacity reached 7.02 mg/g. The adsorption kinetics and isothermal adsorption of Cd2 on biochar modified with 0.2% phosphoric acid (0.2 PB) closely followed the pseudo-first-order kinetics model (R2 > 0.98) and the Freundlich model (R2 > 0.97), respectively. This suggests that the adsorption process involves both physical and chemical mechanisms. SEM and FTIR analyses revealed that phosphoric acid modification primarily increased the biochar’s specific surface area and enhanced certain original functional groups. The adsorption process predominantly involved rapid ion diffusion and chemical adsorption, as confirmed by kinetic analysis and isothermal adsorption model analysis. In summary, the adsorption efficiency of 0.2 PB significantly improved, showing potential and feasibility for heavy metal remediation in soil. This supports the environmentally friendly concept of “treating waste with waste”.

Research Progress on Removal of Oxygenatesin Fischer-Tropsch Oil by Adsorption

The oxygen-containing compounds in Fischer Tropsch synthetic oil greatly affect the downstream deep processing of hydrocarbons,and effective removal is required.Com-pared to traditional removal technologies such as hydrogenation deoxygenation,solvent extraction,and extraction distillation,adsorption deoxygenation technology has the advantages of low cost,mild operating conditions,easy removal and recovery,and mini-mal impact on oil quality.Therefore,adsorption deoxygenation technology has devel-oped rapidly in various removal processes and has become a research hotspot in the cur-rent Fischer Tropsch oil deoxygenation.Adsorbents are the core of adsorption deoxygen-ation technology.Therefore,this article briefly introduces the adsorption mechanism and summarizes the research progress of adsorbents widely used in recent years,such as silica gel,alumina,molecular sieves,and metal organic frameworks,in adsorbing oxygen-containing compounds in Fischer Tropsch synthetic oils.And provide reference sugges-tions for further adsorption and deoxygenation directions in the future.

Design, synthesis, and nanoengineered modification of spherical graphene surface by layered double hydroxide (LDH) for removal of As (Ⅲ) from aqueous solutions

In this study, new nano spherical graphene modified with LDH(Layered Double Hydroxide) was prepared and used to remove As(Ⅲ) ion from aqueous solutions. At first, graphene oxide was synthesized from graphite using a well-known Hammer method. The obtained graphene oxide solution was sprayed in octanol solution under different temperatures and sprayed speed as influenced variables. The structure and physical characterization of synthesized spherical graphene oxide were determined by various techniques,including FT-IR, N_(2) adsorption–desorption, SEM, TEM, and EDX. In the next step, the hydrothermal method was applied to deposition LDH on the spherical graphene oxide. The synthesized spherical graphene modified by LDH was used to remove As(Ⅲ) as a toxic heavy metal ion. The effect of influenced variables including p H, contact time, amount of sorbent, and type eluent studied and the optimum values were as 8, 30, 50, and HCl(0.5 mol·L^(-1)), respectively. After optimization, the studied sorbent was shown a high adsorption capacity(149.3 mg·g^(-1)). The adsorption mechanism and kinetic models exhibited good agreement with the Langmuir isotherm and pseudo-second-order trends, respectively. Besides, the synthesized product was tested for seven times without significant loss in its sorption efficiency.

Recent Advances in the Comprehension and Regulation of Lattice Oxygen Oxidation Mechanism in Oxygen Evolution Reaction

Water electrolysis,a process for producing green hydrogen from renewable energy,plays a crucial role in the transition toward a sustainable energy landscape and the realization of the hydrogen economy.Oxygen evolution reaction(OER)is a critical step in water electrolysis and is often limited by its slow kinetics.Two main mechanisms,namely the adsorbate evolution mechanism(AEM)and lattice oxygen oxidation mechanism(LOM),are commonly considered in the context of OER.However,designing efficient catalysts based on either the AEM or the LOM remains a topic of debate,and there is no consensus on whether activity and stability are directly related to a certain mechanism.Considering the above,we discuss the characteristics,advantages,and disadvantages of AEM and LOM.Additionally,we provide insights on leveraging the LOM to develop highly active and stable OER catalysts in future.For instance,it is essential to accurately differentiate between reversible and irreversible lattice oxygen redox reactions to elucidate the LOM.Furthermore,we discuss strategies for effectively activating lattice oxygen to achieve controllable steady-state exchange between lattice oxygen and an electrolyte(OH^(-)or H_(2)O).Additionally,we discuss the use of in situ characterization techniques and theoretical calculations as promising avenues for further elucidating the LOM.

Adsorption behavior of activated carbon for the elimination of zearalenone during bleaching process of corn oil

Zearalenone is a mycotoxin produced by Fusarium species.It frequently contaminates cereals used for foods or animal feeds,especially deposited in crude corn oil.Certain amounts of zearalenone can be removed during refining processes.In this study,we studied the influence of activated carbon and six industial absorbents(zeolite,diatomite,attapulgite,perlite,montmorillonite and activated clay)on the elimination of zearalenone during bleaching process of corn oil and explored the absorption mechanism of activated carbon.Results showed that activated carbon had an excellent adsorption capacity of zearalenone compared with the other six industrial adsorbents.For activated carbon,a high removal rate of zearalenone(exceeding 83%)from heavily zearalenone-polluted corn oil was achieved and the removal rate of zearalenone was kept above 60%after five regeneration cycles.The research on the adsorption mechanism of activated carbon showed that Freundlich adsorption isotherm model and pseudo-second-order kinetic model could well described the adsorption process.The thermodynamic study demonstrated that adsorption process was spontaneous and exothermic.Fourier transform infrared spectroscopy and Raman spectroscopy further revealed that activated carbon was effectively combined with zearalenone viaπ-πinteraction.Thus,activated carbon is an efficient and suitable adsorbent to control the levels of zearalenone during bleaching process of corn oil.This study not only proposed a systematic research scheme for the mechanism study of activated carbon for the elimination of zearalenone in corn oil,but also provided the scientific basis for developing effective methods to eliminate zearalenone in refined vegetable oils.

The decisive role of adsorbed OH^(*)in low‐potential CO electro‐oxidation on single‐atom catalytic sites

CO impurity-induced catalyst deactivation has long been one of the biggest challenges in proton-exchange membrane fuel cells,with the poisoning phenomenon mainly attributed to the overly strong adsorption on the catalytic site.Here,we present a mechanistic study that overturns this understanding by using Rh-based single-atom catalysis centers as model catalysts.We precisely modulated the chelation structure of the Rh catalyst by coordinating Rh with C or N atoms,and probed the reaction mechanism by surface-enhanced Raman spectroscopy.Direct spectroscopic evidence for intermediates indicates that the reactivity of adsorbed OH^(*),rather than the adsorption strength of CO^(*),dictates the CO electrocatalytic oxidation behavior.The RhN_(4)sites,which adsorb the OH^(*)intermediate more weakly than RhC4 sites,showed prominent CO oxidation activity that not only far exceeded the traditional Pt/C but also the RhC4 sites with similar CO adsorption strength.From this study,it is clear that a paradigm shift in future research should be considered to rationally design high-performance CO electro-oxidation reaction catalysts by sufficiently considering the water-related reaction intermediate during catalysis.