Effective removal of chromium,copper,and nickel heavy metal ions from industrial electroplating wastewater by in situ oxidative adsorption using sodium hypochlorite as oxidant and sodium trititanate nanorod as adsorbent

Sodium hypochlorite and synthesized sodium trititanate nanorods(Na_(2)Ti_(3)O_(7),186 nm×1270 nm)were used as the oxidant and adsorbents for in situ oxidative adsorption treatment of actual electroplating wastewater containing Cr(Ⅵ)(2.6-5.2 mg·L^(-1)),Cu^(2+)(2.7-5.4 mg·L^(-1)),and Ni^(2+)(0.2705-0.541 mg·L^(-1))ions at pH of 8.8-9.1 and 20-60℃.The as-synthesized sodium trititanate nanorods were characterized by XRD,HRTEM,N2 adsorption/desorption,SEM,EDX,and zeta potential techniques.The concentrations of heavy metal ions in wastewater were analyzed by ICP technique.After in situ oxidative adsorption treatment under the concentrations of 25 g·L^(-1) for sodium hypochlorite and 125 mg·L^(-1) for sodium trititanate nanorods at 60℃ for 5 h,the heavy metal ion concentrations could be reduced from initial value of 2.6 to final value of 1.92 mg·L^(-1) for Cr(Ⅵ),3.6 to 0.17 mg·L^(-1) for Cu^(2+),and from 0.2705 to 0.097 mg·L^(-1) for Ni^(2+),respectively.Cr(Ⅵ),Cu^(2+) and Ni^(2+) ions could be effectively removed by the in situ oxidative adsorption method.The in situ oxidative adsorption processes of Cr(Ⅵ),Cu^(2+) and Ni^(2+) ions are satisfactorily simulated by the pseudo-second order adsorption kinetics and Langmuir adsorption isotherm,respectively.Adsorption thermodynamics analyses reveal that the oxidative adsorption processes of Cr(Ⅵ),Cu^(2+) and Ni^(2+) ions are spontaneous and endothermic.The oxidation degree of metalcontained complexes influences the values of thermodynamics functions.

Comments on“Adsorption behavior of heavy metal ions by carbon nanotubes grown on microsized Al_2O_3 particles”

Recently, Hsieh and Horng [1] published the paper entitled as above. In section 3 results and discussion, the authors mentioned the first and the second order kinetic models without any quotations. In fact these two kinetic models have been published [2-5]. In order to distinguish a kinetics model based on the ad- sorption capacity of a solid from the one based on the concentration of a solution, Lagergren＇s first-order rate equation has been called pseudo-first-order [6-7]. The Lagergren＇s equation has been widely cited, but there are far more mistakes made in the quotation and in the reference section of papers, including the title, the author＇s name, journal title, year of publishing, volume, and page number [3]. In addition, the second order kinetic expression for the adsorption systems of divalent metal ions using sphagnum moss peat has been reported by Ho [8].

Adsorption of Heavy Metal Ions,Dyes and Proteins by Chitosan Composites and Derivatives-A Review

Chitosan composites and derivatives have gained wide attentions as effective biosorbents due to their low costs and high contents of amino and hydroxyl functional groups.They have showed significant potentials of removing metal ions,dyes and proteins from various media.Chemical modifications that lead to the formation of the chitosan derivatives and chitosan composites have been extensively studied and widely reported in literatures.The aims of this review were to summarize the important information of the bioactivities of chitosan,highlight the various preparation methods of chitosan-based active biosorbents,and outline its potential applications in the adsorption of heavy metal ions,dyes and proteins from wastewater and aqueous solutions.

Adsorption properties of a novel 3D graphene/MgO composite for heavy metal ions

A novel three-dimension(3D)graphene/MgO composite was synthesized through self-assembly and embedding MgO nanoparticle in reduced graphene in situ.Fourier transform infrared(FT-IR)spectroscopy,thermal gravimetric analysis(TGA),scanning electron microscopy(SEM),transmission electron microscope(TEM),powder X-raydiffraction(XRD)and X-rayphotoelectron spectroscopy(XPS)were employed to characterize the prepared 3D graphene/MgO composite.The adsorption performance of some metal ions on 3D graphene/MgO was investigated.The results showed that the adsorption capacity was greater than 3D graphene and the maximum adsorption capacity at 25℃was found to be 358.96 mg/g,388.4 mg/g and 169.8 mg/g for Pb^2+,Cd^2+and Cu^2+,respectively.The adsorption kinetic conformed to the pseudo-second-order kinetic model and the adsorption isotherm was well described by Langmuir model.The thermodynamic constants revealed that the sorption process was endothermic and spontaneous in nature.Based on the results of the removal of heavy metal ions from metal smelting wastewater,it can be concluded that the prepared 3D graphene/MgO composite is an effective and potential adsorbent.

Binding and Adsorption Energies of Heavy Metal Ions with Hapli-Udic Argosol and Ferri-Udic Argosol Particles

Gibbs free binding energy and adsorption energy between cations and charged soil particles were used to evaluate the interactions between ions and soil particles. The distribution of Gibbs free adsorption energies could not be determined experimentally before the development of Wien effect measurements in dilute soil suspensions. In the current study, energy relationships between heavy metal ions and particles of Hapli-Udic Argosol （Alfisol） and Ferri-Udic Argosol were inferred from Wien effect measurements in dilute suspensions of homoionic soil particles （〈 2 μm） of the two soils, which were saturated with ions of five heavy metals, in deionized water. The mean Gibbs free binding energies of the heavy metal ions with Hapli-Udic Argosol and Ferri-Udic Argosol particles diminished in the order of Pb^2＋ 〉 Cd^2＋ 〉 Cu^2＋ 〉 Zn^2＋ 〉 Cr^3＋, where the range of binding energies for Hapli-Udic Argosol （7.25-9.32 kJ mol^-1） was similar to that for Ferri-Udic Argosol （7.43-9.35 kJ mol^-1）. The electrical field-dependent mean Gibbs free adsorption energies of these heavy metal ions for Hapli-Udic Argosol and for Ferri-Udic Argosol descended in the order： Cu^2＋ 〉 Cd2^＋ 〉 Pb^2＋ 〉 Zn^2＋ 〉 Cr^3＋, and Cd^2＋ 〉 Cu^2＋ 〉 Pb^2＋ 〉 Zn^2＋ 〉 Cr^3＋, respectively. The mean Gibbs free adsorption energies of Cu^2＋, Zn^2＋, Cd^2＋, Pb^2＋, and Cr^3＋ at a field strength of 200 kV cm^-1, for example, were in the range of 0.8-3.2 kJ mo1^-1 for the two soils.

The Use of New Chemically Modified Cellulose for Heavy Metal Ion Adsorption and Antimicrobial Activities

A novel chemically modified cellulose (DTD) adsorbent bearing pendent methyl benzalaniline chelating group was synthesized. This new adsorbent was used for the removal of Cu2+ and Pb2+ heavy metal ions from aqueous solution. The chemical and structural characteristics of the adsorbent were determined using FT-IR, 13C CP-MAS NMR, SEM, EDX and TGA analysis. The adsorption parameters, such as pH, adsorbent dose, contact time, initial metal ion concentration and temperature were optimized. Adsorption kinetic parameters were fitted into pseudo-first-order and pseudo-second-order models. The kinetic data fitted well to the pseudo-second-order kinetic model. The adsorption isotherms such as Freundlich and Langmuir isotherms have been investigated. Thermodynamic parameters have also been evaluated. The negative values of △G0 and △H0 reveal that the adsorption system is spontaneous and exothermic in nature. The modified cellulose was challenged with microorganisms as a function of contact time. The biocidal results showed that the chemically modified cellulose has bactericidal effect against the bacterial species.

Sorption Characteristics for Multiple Adsorption of Heavy Metal Ions Using Activated Carbon from Nigerian Bamboo

Sorption characteristics of multiple adsorption of six heavy metal ions often found in refinery waste waters using activated carbon from Nigerian bamboo was investigated. The bamboo was cut, washed and dried. It was carbonized between 350℃ - 500℃, and activated at 800℃ using nitric acid. Simultaneous batch adsorption of different heavy metal ions (Cd2+, Ni2+, Pb2+, Cr3+, Cu2+ and Zn2+) in same aqueous solution using activated carbon from Nigerian bamboo was carried out. The adsorption process had a better fit for the Freundlich, Temkin isotherm and Dubinin-Radushke-vich (DRK) isotherm models but could not fit well into Langmuir isotherm. Adsorption isotherms showed that there is competition among various metals for adsorption sites on Nigerian bamboo. The DRK model was used to determine the nature of the sorption process and was found to be physical and chemical, with sorption energy of metal ions ranging from (7 - 10 kJ/mol). The adsorption of Cd2+, Zn2+, Pb2+ and Ni2+ ions was chemisorptions and that of Cu2+ and Cr3+ ions was cooperative adsorption. Therefore, this study revealed that Nigerian bamboo can serve as a good source of activated carbon with multiple and simultaneous metalions—removing potentials and may serve as a better replacement for commercial activated carbons in applications that warrant their use.

Comparative adsorption of heavy metal ions in wastewater on monolayer molybdenum disulfide

To maximize the potential of monolayer molybdenum disulfide(MoS2)sheet in the disposal of heavy metal ions in wastewater,we compared the adsorption of several common heavy metal ions(including Cr^(3+),Ni^(2+),Cu^(2+),Zn^(2+),Cd^(2+),Hg^(2+),and Pb^(2+))in wastewater on the monolayer MoS2 sheet through first-principles calculation.Our simulation results show that the monolayer MoS2 sheet is a potential heavy metal adsorption material because of the attractive interaction between them.The most negative adsorption energy determines that the TMo site is the most stable adsorption site for the heavy metal ions.The attractive interaction is considered as chemical adsorption,and it is closely related to charge transfer.The orbital hybridization between S p and heavy metal ions p and d states electrons contributes to the adsorption,except the orbital hybridization between S p and Pb p states electrons contributes to the Pb^(2+) adsorption.All the results show that the monolayer MoS2 sheet is most suitable for removing Ni^(2+) and Cr^(3+) ions from wastewater,followed by Cu^(2+) and Pb^(2+).For the ions Cd^(2+),Zn^(2+),and Hg^(2+),its adsorption strength remains to be improved.

Robust Waterborne Polyurethane/Wool Keratin/Silk Sericin Freeze-Drying Composite Membrane for Heavy Metal Ions Adsorption

Wool keratin(WK)and silk sericin(SS)have the ability to interact with metal ions.In order to take advantage of this potential,a novel environmentally friendly waterborne polyurethane(WPU)/WK/SS membrane named as WPU&WK&SS membrane with crosslinked structure was constructed by freeze-drying via self-assembly style.Surface morphology and chemical structure characterization were investigated by scanning electron microscopy(SEM)and Fourier transform infrared spectroscopy(FT-IR).In addition,the adsorption experiments of Cu2+and Cr6+were performed to evaluate the adsorption of WPU&WK&SS membrane,including adsorption kinetics,adsorption isotherm models and various factors affecting adsorption.Further investigation indicates that the maximum adsorption capacity of Cu2+and Cr6+can reach 54.21 mg·g-1and 85.21 mg·g-1,respectively,which are higher than most of the reported adsorbents.Through adsorption kinetics and thermodynamic analysis,it is find that the pseudo-second-order kinetic equation and the Langmuir adsorption isotherm model are more suitable for the static adsorption of Cu2+and Cr6+by WPU&WK&SS membrane.

Adsorption of Ammonium and Heavy Metal Ions on Industrial Vermiculite from the Yuli Mine in Xinjiang, China

The present work discusses the mineralogy, saturated adsorption of ammonium and adsorption of heavy metal ions （Cu^2＋, Pb^2＋ and Zn^2＋） on industrial vermiculite samples from the Yuli Mine in Xinjiang Autonomous Region. The saturated adsorption capacity of ammonium and the affection factors of adsorption of Cu^2＋, Pb^2＋ and Zn^2＋ are discussed on the basis of the mineralogical characteristics of the industrial vermiculite samples. The saturated adsorption capacities of ammonium are between 56.02 and 98.42 mmol/100g. The time of adsorption equilibrium is about 30-60 min, and the pH values and concentration of the ion solution significantly affect the adsorption capacities of the heavy metal ions. The adsorption capabilities of the heavy metal ions on industrial vermiculite are almost the same in the low ion concentration solutions, characterized by a sequence of Zn^2＋〉Pb^2＋〉Cu^2＋ for adsorption capacity in solutions with relatively high ion concentration. The results have practical significance for the application of the industrial vermiculite to treating wastewater containing ammonium or heavy metal ions.

Adsorption of Heavy Metal Ions by Adsorbent from Waste Mycelium Chitin

The adsorption properties of chitin adsorbent from mycelium of fermentation industries for the removal of heavy metal ions were studied. The result shows that the chitin adsorbent has high adsorption capacity for many heavy metal ions and Ni2+ in citric acid. The influence of pH was significant:When pH is higher than 4.0, the high adsorption capacity is obtained,otherwise H+ ion inhibits the adsorption of heavy metal ions. The comparison of the chitin adsorbent with some other commercial adsorbents was made, in which that the adsorption behaviorchitin adsorbent is close to that of commercial cation exchange adsorbents, and its cost is much lower than those commercial adsorbents.

Adsorption of Cr(VI) by modified chitosan from heavy-metal polluted water of Xiangjiang River, China

Methacrylic acid was used together with a molecular imprinting technique to modify chitosan. In addition, the adsorption kinetics and adsorption isotherms were recorded and the results were analyzed to investigate reparative adsorption for Cr（VI） from the polluted Xiangjiang River water. A comparative X-ray analysis shows that the degree of crystallization in the imprinted polymer was significantly weakened, the area of the non-crystalline region was larger. There were more adsorption sites in the imprinted polymer, and the adsorption capacity towards Cr（VI） was increased. The adsorption capacity of the imprinted polymer towards Cr（VI） increased with time and reaches saturation after 8 h. The optimal adsorption time was 4-8 h after the adsorption starting and the optimal pH value for the solution was in the range of 4.5-7.5. When the chitosan reaches saturation, the adsorption capacity achieves a state of equilibrium, and the maximum Cr（VI） extraction rate reaches 33.7%. Moreover, the adsorption capacity of the imprinted polymer towards Cr（VI） increases with increasing chitosan concentration. In this situation, the Cr（VI） extraction rate shows little variation, and the maximum removal rate can reach 98.3%. Furthermore, the Cr（VI） extraction rate increases with an increase in the degree of deacetylation in the chatoyant and chitosan, with the best adsorption effect corresponding to 90% deacetylation. Fitting the adsorption data to the quasi first- and second-order kinetic models yields correlation coefficients of 0.9013 and 0.9875, respectively. The corresponding rate constants for the two models are 0.0091 min-1 and 7.129 g/（mg.min）, respectively. Hence, the adsorption using Cr（VI）-imprinted chitosan is more consistent with the second-order kinetics. Comparing the data to Freundlich and Langrnuir adsorption isotherms shows that the latter has a better linear fit and a maximum adsorption capacity of 15.784 mg/g.

Removal of heavy metals from aqueous solution by sawdust adsorption

The adsorption of lead, cadmium and nicel from aqueous solution by sawdust of walnut was investigated. The effect of contact time, initial metal ion concentration and temperature on metal ions removal has been studied. The equilibrium time was found to be of the order of 60 min. Kinetics fit pseudo first-order, second-order and intraparticle diffusion models, hence adsorption rate constants were calculated. The adsorption data of metal ions at temperatures of 25, 45 and 60~C have been described by the Freundlich and Langmuir isotherm models. The thermodynamic parameters such as energy, entropy and enthalpy changes for the adsorption of heavy metal ions have also been computed and discussed. Ion exchange is probably one of the major adsorption mechanisms for binding divalent metal ions to the walnut sawdust. The selectivity order of the adsorbent is Pb（I1）~Cd（II）〉Ni（I1）. From these results, it can be concluded that the sawdust of walnut could be a good adsorbent for the metal ions from aqueous solutions.

Novel modified pectin for heavy metal adsorption

Modified pectin cross-linked with adipic acid, was synthesized and used for heavy metal removal from wastewater. SEM and FTIR were used to investigate its structure and morphology. The modified pectin had a rough, porous phase covered with carboxy groups, resulting a high adsorption capacity. And at the room temperature, the saturated loading capacity for Pb^2＋, Cu^2＋ and Zn^2＋ reached 1.82 retool/g, 1.794 mmol/g and 0.964 retool/g, respectively. The results proved its potential application to remove of the heavy metal.

Superior adsorption performance of graphitic carbon nitride nanosheets for both cationic and anionic heavy metals from wastewater

Water pollution caused by highly toxic Cd(II), Pb(II), and Cr(VI) is a serious problem. In the present work,a green and low-cost adsorbent of g-C_3N_4 nanosheets was developed with superior capacity for both cationic and anionic heavy metals. The adsorbent was easily fabricated through one-step calcination of guanidine hydrochloride with thickness less than 1.6 nm and specific surface area of 111.2 m^2·g^(-1). Kinetic and isotherm studies suggest that the adsorption is an endothermic chemisorption process, occurring on the energetically heterogeneous surface based on a hybrid mechanism of multilayer and monolayer adsorption. The tri-s-triazine units and surface N-containing groups of g-C_3N_4 nanosheets are proposed to be responsible for the adsorption process.Further study on pH demonstrates that electrostatic interaction plays an important role. The maximum adsorption capacity of Cd(II), Pb(II), and Cr(VI) on g-C_3N_4 nanosheets is 123.205 mg·g^(-1), 136.571 mg·g^(-1),and 684.451 mg·g^(-1), respectively. The better adsorption performance of the adsorbent than that of the recently reported nanomaterials and low-cost adsorbents proves its great application potential in the removal of heavy metal contaminants from wastewater. The present paper developed a promising adsorbent which will certainly find applications in wastewater treatment and also provides guiding significance in designing adsorption processes.

Single and competitive adsorption affinity of heavy metals toward peanut shell-derived biochar and its mechanisms in aqueous systems

Converting peanut shells into biochar by pyrolysis was considered an environmentally friendly and efficient method for agricultural solid waste disposal.The properties of peanut shell-derived biochar(PBC)under different temperature and its adsorption capacity of heavy metals were investigated.It was found that PBC400 exhibited the highest cumulative capability for heavy metals elimination in single solute because of its high specific surface area and rich functional groups.Furthermore,the competitive adsorption revealed that PBC had a substantial difference in adsorption affinity from diverse heavy metal ions,sorption capacity decreased as Pb2+>Cu2+>Cd2+>Ni2+>Zn2+,which was lower than in a single solute.The adsorption process using selected biochar was optimized with respect to p H,reaction time,adsorbent dose,and initial concentration of heavy metals.The kinetic data was well fitted with PSO model,and the Langmuir model was adopted for adsorption equilibrium data in both cases of single solutes and mixed solutes for all heavy metals,which indicated that the removal course was primarily explained by monolayer adsorption,and chemical adsorption occupied an important role.Therefore,peanut shells derived biochar could be a potential and green adsorbent for wastewater treatment.

Removal of heavy metals from aqueous solution by carbon nanotubes: adsorption equilibrium and kinetics

Carbon nanotubes prepared by catalytic chemical vapor deposition of hydrocarbon at 650℃ show good adsorption capability of Pb 2+ , Cu 2+ and Cd 2+ ions from aqueous solution after oxidized with concentrated nitric acid at 140℃ for 1 h. The specific surface area and particle size distribution of the as-grown and oxidized CNTs were studied by BET method and laser particle analyzer. Three kinetic models, that is, first-, pseudo second- and second-order, were used to investigate the adsorption data and the pseudo second-order model can represent the experimental data better than two others. The equilibrium data fitted well with the Langmuir model and showed the following adsorption order: Pb 2+ >Cu 2+ >Cd 2+ .

A REVIEW OF HEAVY METAL ADSORPTION BY MARINE ALGAE

Accumulation of heavy metals by algae had been studied extensively for biomonitoring or bioremediation purposes. Having the advantages of low cost raw material, big adsorbing capacity, no secondary pollution, etc., algae may be used to treat industrial water containing heavy metals. The adsorption processes were carried out in two steps: rapid physical adsorption first, and then slow chemical adsorption. pH is the major factor influencing the adsorption. The Freundlich equation fitted very well the adsorption isotherms. The uptake decreased with increasing ionic strength. The principal mechanism of metallic cation sequestration involves the formation of complexes between a metal ion and functional groups on the surface or inside the porous structure of the biological material. The carboxyl groups of alginate play a major role in the complexation. Different species of algae and the algae of the same species may have different adsorption capacity. Their selection affinity for heavy metals was the major criterion for the screening of a biologic adsorbent to be used in water treatment. The surface complex formation model (SCFM) can solve the equilibrium and kinetic problems in the biosorption.

A New Competitive Adsorption Isothermal Model of Heavy Metals in Soils

A new competitive adsorption isothermal model(CAIM)was developed for the coexistent and competitive binding of heavy metals to the soil surface.This model extended the earlier adsorption isothermal models by considering more than one kind of ion adsorption on the soil surface.It was compared with the Langmuir model using different conditions, and it was found that CAIM,which was suitable for competitive ion adsorption at the soil solid-liquid surface,had more advantages than the Langmuir model.The new competitive adsorption isothermal model was used to fit the data of heavy metal(Zn and Cd)competitive adsorption by a yellow soil at two temperatures.The results showed that CAIM was appropriate for the competitive adsorption of heavy metals on the soil surface at different temperatures.The fitted parameters of CAIM had explicit physical meaning.The model allowed for the calculation of the standard molar Gibbs free energy change,the standard molar enthalpy change,and the standard molar entropy change of the competitive adsorption of the heavy metals,Zn and Cd,by the yellow soil at two temperatures using the thermodynamic equilibrium constants.

Heavy Metal Removal from Water by Adsorption Using Pillared Montmorillonite

Removal of Cu^2＋, Cr^3＋ and Cd^2＋ from aqueous solutions by adsorption on montmorillonite modified by sodium dodecylsulfate （SDS） and hydroxy-alumino-silicate （HAS） was investigated. Experiments were carried out as a function of solution pH, solute concentration, and time. The Langmuir model was adopted to describe the single-solute adsorption isotherm, in which the Langmuir parameters were directly taken from those obtained in single-solute systems. The kinetics of metal ions adsorption was examined and the pseudo-first-order rate constant was finally evaluated.