EXPERIMENTAL STUDY OF HIGH SUBSONIC CAVITY FLOW OSCILLATION AND ITS SUPPRESSION BY ACOUSTIC EXCITATION

An experimental study of cavity oscillating flow carried out on subsonic wall jet facilities in an anechoic room is summarized. The jet exit Mach number range is from 0.2 to 0.8. The effects of the flow Mach number ( Ma ) and the cavity depth ( D ) on the oscillation are studied. It is found that for L/D =4, (shallow cavity), the oscillation is mainly due to the self exciting of the free shear layer above the cavity opening, for L/D =2, the acoustic resonance is responsible for the oscillation. Preliminary tests are performed to study the suppression effect of the leading edge tone excitation on cavity flow, and considerable reduction of oscillation has been achieved when Ma ≤0.6.

Aerodynamic load control on a dynamically pitching wind turbine airfoil using leading-edge protuberance method

The aerodynamic loads of wind turbine blades are substantially affected by dynamic stall induced by the variations of the angle of attack of local airfoil sections.The purpose of the present study is to explore the effect of leading-edge protuberances on the fluctuation of the aerodynamic performances for wind turbine airfoil during dynamic stall.An experimental investigation is carried out by a direct force measurement technique employing force balance at a Reynolds number Re=2×105.The phase-averaged and instantaneous aerodynamic loads of the pitching airfoil,including the baseline and the wavy airfoil,are presented and analyzed.The phase-averaged results indicate that the effects of dynamic stall for the wavy airfoil can be delayed or minimized compared to the baseline airfoil,and the negative damping area of the wavy airfoil is significant decreased in full-stall condition.These effects of leading-edge protuberances are more notable at a higher reduced frequency.For the instantaneous aerodynamic loads of the wavy airfoil,there is an observable reduction in fluctuations compared with baseline case.Furthermore,spectral analysis is applied to quantitatively undercover the nonstationary features of the instantaneous aerodynamic loads.It is found that the leading edge protuberances can reduce the harmonics of the aerodynamic force signal,and enhance the stability of the aerodynamic loads under different reduced frequencies.In conclusion,leading-edge protuberances are found effective to reduce the fluctuation characteristics of the aerodynamic loads during the dynamic stall process,and help to improve the stability and prolong the service life of the wind turbine blades.

Experimental investigations of a full model with adaptive elasto-flexible membrane wings

The morphing wing concept aims to constantly adapt the aerodynamics to different flight stages.The wing is able to adapt to different flight conditions by an adjustable Aspect Ratio(AR)and sweep.A high AR configuration provides high aerodynamic efficiency,while a low AR configuration,with highly swept wings offers a good maneuverability.Additionally,the flexible membrane allows the wing surface to stretch and contract in-plane as well as the airfoil to adapt to different aerodynamic loads.In the context of this work,the aerodynamic characteristics of a full model with form-adaptive elasto-flexible membrane wings are investigated experimentally.The focus is on the high-lift regime and on the analysis of the aerodynamic coefficients as well as their sensitivities.Especially,the lateral aerodynamic derivatives at asymmetric wing positions are of interest.

Aerodynamic design,analysis,and validation techniques for the Tianwen-1 entry module

The clear differences between the atmosphere of Mars and the Earth coupled with the lack of a domestic research basis were significant challenges for the aerodynamic prediction and verification of Tianwen-1.In addition,the Mars entry,descent,and landing(EDL)mission led to specific requirements for the accuracy of the aerodynamic deceleration performance,stability,aerothermal heating,and various complex aerodynamic coupling problems of the entry module.This study analyzes the key and difficult aerodynamic and aerothermodynamic problems related to the Mars EDL process.Then,the study process and results of the design and optimization of the entry module configuration are presented along with the calculations and experiments used to obtain the aerodynamic and aerothermodynamic characteristics in the Martian atmosphere.In addition,the simulation and verification of the low-frequency free oscillation characteristics under a large separation flow are described,and some special aerodynamic coupling problems such as the aeroelastic buffeting response of the trim tab are discussed.Finally,the atmospheric parameters and aerodynamic characteristics obtained from the flight data of the Tianwen-1 entry module are compared with the design data.The data obtained from the aerodynamic design,analysis,and verification of the Tianwen-1 entry module all meet the engineering requirements.In particular,the flight data results for the atmospheric parameters,trim angles of attack,and trim axial forces are within the envelopes of the prediction deviation zones.

Aeroelastic optimization design for wing with maneuver load uncertainties

An aeroelastic optimization design methodology for air vehicle considering the uncertainties in maneuver load conditions is presented and applied to a structural design process of low-aspect-ratio wing. An aerodynamic load correction model is developed and used to predict the critical load conditions with the perturbations of theoretical linear aerodynamic forces and experimental aerodynamic forces from wind-tunnel test, when concerning the uncertainties in use of theoretical linear and experimental aerodynamic forces. Three objective functions of critical loads are defined. The load evaluations for three wing sections are investigated in four characteristic maneuvers, and the most critical load conditions are confirmed by using the sequential quadratic programming method. On this basis, the aeroelastic optimization design employing the genetic-gradient hybrid algorithm is conducted, in which the objective is to minimize structural mass subject to the constraints of stress, deformation and flutter speed. The resulting optimal structure is heavier than the one simply based on the theoretical linear or experimental aerodynamic forces. However, it is more robust when encountering the critical load conditions in actual flight due to the consideration of uncertainties in aerodynamic forces in the early design phase, thereby, the risk of structural redesign can be reduced.

Flight dynamics modeling of a small ducted fan aerial vehicle based on parameter identifcation

This paper presents a simple and useful modeling method to acquire a dynamics model of an aerial vehicle containing unknown parameters using mechanism modeling,and then to design different identifcation experiments to identify the parameters based on the sources and features of its unknown parameters.Based on the mathematical model of the aerial vehicle acquired by modeling and identifcation,a design for the structural parameters of the attitude control system is carried out,and the results of the attitude control flaps are verifed by simulation experiments and flight tests of the aerial vehicle.Results of the mathematical simulation and flight tests show that the mathematical model acquired using parameter identifcation is comparatively accurate and of clear mechanics,and can be used as the reference and basis for the structural design.

Effects of wing locations on wing rock induced by forebody vortices

Previous studies have shown that asymmetric vortex wakes over slender bodies exhibit a multi-vortex structure with an alternate arrangement along a body axis at high angle of attack. In this investigation, the effects of wing locations along a body axis on wing rock induced by forebody vortices was studied experimentally at a subcritical Reynolds number based on a body diameter. An artificial perturbation was added onto the nose tip to fix the orientations of forebody vortices. Particle image velocimetry was used to identify flow patterns of forebody vortices in static situations, and time histories of wing rock were obtained using a free-to-roll rig. The results show that the wing locations can affect significantly the motion patterns of wing rock owing to the variation of multi- vortex patterns of forebody vortices. As the wing locations make the forebody vortices a two-vortex pattern, the wing body exhibits regularly divergence and fixed-point motion with azimuthal varia- tions of the tip perturbation. If a three-vortex pattern exists over the wing, however, the wing-rock patterns depend on the impact of the highest vortex and newborn vortex. As the three vortices together influence the wing flow, wing-rock patterns exhibit regularly fixed-points and limitcycled oscillations. With the wing moving backwards, the newborn vortex becomes stronger, and wing-rock patterns become fixed-points, chaotic oscillations, and limit-cycled oscillations. With fur- ther backward movement of wings, the vortices are far away from the upper surface of wings, and the motions exhibit divergence, limit-cycled oscillations and fixed-points. For the rearmost location of the wing, the wing body exhibits stochastic oscillations and fixed-points.