Research on Operation Optimization of Heating System Based on Electric Storage Coupled Solar Energy and Air Source Heat Pump

For heating systems based on electricity storage coupled with solar energy and an air source heat pump(ECSA),choosing the appropriate combination of heat sources according to local conditions is the key to improving economic efficiency.In this paper,four cities in three climatic regions in China were selected,namely Nanjing in the hot summer and cold winter region,Tianjin in the cold region,Shenyang and Harbin in the severe cold winter region.The levelized cost of heat(LCOH)was used as the economic evaluation index,and the energy consumption and emissions of different pollutants were analyzed.TRNSYS software was used to simulate and analyze the system performance.The Hooke-Jeeves optimization algorithm and GenOpt software were used to optimize the system parameters.The results showed that ECSA systemhad an excellent operation effect in cold region and hot summer and cold winter region.Compared with ECS system,the systemenergy consumption,and the emission of different pollutants of ECSA system can be reduced by a maximum of 1.37 times.In cold region,the initial investment in an air source heat pump is higher due to the lower ambient temperature,resulting in an increase in the LOCH value of ECSA system.After the LOCH value of ECSA system in each region was optimized,the heating cost of the system was reduced,but also resulted in an increase in energy consumption and the emission of different pollutant gases.

Modeling and Optimization of Solar Collector Design for the Improvement of Solar-Air Source Heat Pump Building Heating System

To enhance system stability,solar collectors have been integrated with air-source heat pumps.This integration facilitates the concurrent utilization of solar and air as energy sources for the system,leading to an improvement in the system’s heat generation coefficient,overall efficiency,and stability.In this study,we focus on a residential building located in Lhasa as the target for heating purposes.Initially,we simulate and analyze a solar-air source heat pump combined heating system.Subsequently,while ensuring the system meets user requirements,we examine the influence of solar collector installation angles and collector area on the performance of the solar-air source heat pump dual heating system.Through this analysis,we determine the optimal installation angle and collector area to optimize system performance.

Operating performance of novel reverse-cycle defrosting method based on thermal energy storage for air source heat pump

To solve the fundamental problem of insufficient heat available during defrosting while ensuring the efficient and safe system operation for air-source heat pumps (ASHPs). A novel reverse-cycle defrosting (NRCD) method based on thermal energy storage to eliminate frost off the outdoor coil surface was developed. Comparative experiments using both the stand reverse cycle defrosting (SRCD) method and the NRCD method were carried out on an experimental ASHP unit with a nominal 2.5 kW heating capacity. The results indicate that during defrosting operation, using the NRCD method improves discharge and suction pressures by 0.24 MPa and 0.19 MPa, respectively, shortens defrosting duration by 60%, and reduces the defrosting energy consumption by 48.1% in the experimental environment, compared with those by the use of SRCD method. Therefore, using the NRCD method can shorten the defrosting duration, improve the indoor thermal comfort, and reduce the defrosting energy consumption in defrosting.

The Efficiency Analysis of the Exhaust Air Heat Pump System

This paper is based on long term parameter measurements of the exhaust air heat pumps (EAHP) system in a new built apartment building. The building was equipped with an exhaust air ventilation system and exhaust air heat pump for ventilation heat recover. The results of the measurements show that the COP of the EAHP is mainly related to the temperature graph of the heating system and the supply temperature of domestic hot water (DWH). During the measurement period some other impact factors, such as the quality of maintenance, the nighttime temperature graph of the heating system, the reduction of the exhaust air flows in case of low temperatures, mistakes in designing and low building quality, have also played a role. An analysis of energy consumption shows that in winter conditions the COP is about 3.0 and in the transition period about 3.3. The energy recovery value of the EAHP is 0.5.

Operation Performance of Air Source Heat Pump System for Space Heating in Tianjin

An air source heat pump system (ASHPS) used in an office building is set up and studied experimentally. Its operating performance in winter is evaluated based on test data and a comparative discussion is given on the effect of climate conditions and heating load ratio on the operation behavior. Then heating capacity variation caused by evaporator frosting is analyzed as well. Finally, the defrosting parameters and the technical feasibility are studied for a constant heating demand. The experimental results indicate that both the outlet water temperature drop and the system COP should be taken into account when setting defrosting parameters, and ASHPS is a viable technology for space heating and hot-water production in winter in Tianjin, which can maintain the room temperature above 19 ℃ when the outdoor temperature is -2 ℃.

Refrigerant Control Strategies for Residential Air-Conditioning and Heat-Pump System

This paper simulated the optimal refrigerant charge inventory of a refrigeration system in air-conditioning operation and heat-pump operation respectively,and studied the refrigerant control strategies in this system.The void fraction in two-phase fluid region was calculated by Harms model.And based on distributed parameter model and Harms model,the refrigerant charge inventory in condenser and evaporator were calculated and analyzed in air-conditioning conditions and heat-pump conditions,respectively.The calculating results of different refrigerant mass between refrigeration and heating conditions indicate that the optimal refrigerant charge inventory in heat-pump conditions is lower than that in air-conditioning conditions.To avoid the decrease of COP due to the surplus refrigerant in heating conditions,we introduced the liquid reservoir control method and associate capillary control method.Both of them could increase the heating capacity of the air-source heat pump.The difference of optimal refrigerant charge inventory in air-conditioning and heat-pump system can be controlled by the liquid reservoir or the associate capillary.

Air pumping for alleviation of heavy smog in Beijing

Beijing often suffers under heavy smog.During such events which occur mostly in autumn and winter,people are desperate for fresh air.The formation of heavy smog is due to foremost human induced air pollution,but geographic and meteorological conditions,especially below a surface inversion,play an important role.We propose to destroy the inversion by pumping air from above the inversion layer to the surface layer to alleviate the severity of the smog.While long-term air quality improvement depends on the reduction of air pollution emission,air pumping may provide relief in the interim for the Beijing citizens.We estimate that an air pumping at a rate 2×10~7m^3s^(–1)can lead to significantly improved air quality in Beijing,due to(1)direct clean air input;(2)increased instability and vertical mixing and(3)a positive radiation-mixing feedback.The pumping requires an energy input of 10 GW,comparable with the energy consumption in Beijing for air conditioning in summer.We propose to use wind energy from Inner Mongolia for the pumping,which has currently an installed wind energy capacity of 70GW.

Applicability of sewage heat pump air-conditioning system

A sewage heat pump system and its application based on a project in Chongqing,China,were discussed. Based on the sewage conditions,a feasibility analysis of the sewage heat pump air conditioning system was conducted. The theoretical and quantitative calculations indicate that sewage flux in the city sewage main pipe in the project can satisfy heat exchange requirements,and taking water from the pipes has relatively small influence on the pipe net in summer and winter. The sewage heat pump air-conditioning system can save 21.5% operating cost in one year,which is energy efficient and environmentally friendly.

Thermodynamic Simulation of CCP in Air-Cooled Heat Pump Unit with HFCs and CO₂Trans-Critical

The exergy analysis and finite time thermodynamic methods had been employed to analyze the compound condensation process (CCP). It was based on the air-cooling heat pump unit. The cooling capacity of the chiller unit is about 1 kW, and the work refrigerant is R22/R407C/R410A/CO2. The MATLAB/SIMULINK software was employed to build the simulation model. The thermodynamic simulation model is significant for the optimization of parameters of the unit, such as condensation and evaporation temperature and mass flow of the sanitary hot water and size of hot water storage tank. The COP of the CCP of R410A system is about 3% - 5% higher than the CCP of the R22 system, while CCP of the R407C system is a little lower than the CCP of R22 system. And the CCP of CO2 trans-critical system has advantage in the hot supply mode. The simulation method provided a theoretical reference for developing the production of CCP with substitute refrigerant R407C/R410A/CO2.

Simulation of Air Source Heat Pump with Refrigerant Injection for Heating Operation

An air source heat pump(ASHP)with refrigerant injection is proposed for the air conditioning system of electric vehicles(EVs),especially for efficient heating in cold winter,when there is no wasted heat of engines.The simulation model is built with the framework of two-phase fluid network,where the compressor is separated as two compressors and the economizer is treated as two heat exchangers in the injection path and the main refrigerant path.With the validated simulation model,the heating performance is analyzed,and the results show that the coefficient of performance(COP)of ASHP with refrigerant injection is higher than 1.4 and the discharge temperature is less than 100℃ when the outdoor temperature is-20℃.The above performance ensures that the air conditioning system and EVs can operate normally with high efficiency even in the cold winter,which is much helpful for the practicability of EVs.

新型低GWP制冷剂在-100~200℃的应用研究进展

制冷剂是蒸气压缩循环中必不可少的工作流体,氢氟烷烃类化合物是目前制冷、空调和热泵设备中的主要制冷剂,但该类制冷剂会引起全球变暖等问题,因此亟需开发应用性能相似、环境性能友好的新型制冷剂。介绍了不同制冷剂在-100~200℃蒸气压缩循环应用场景中的使用现状,并综述了具有前景的低GWP制冷剂替代方案研究进展;在此基础上,对HFO-1234yf、HFO-1234ze(E)、HFO-1234ze(Z)、HCFO-1233zd(E)、HFO-1336mzz(Z) 5种低GWP制冷剂在实际应用系统中的最新研究及关键问题进行总结。

Feasibility Analysis of Back-Pressure Steam Feeding Water Pump for Direct Air-Cooled Unit

As the performance of an air-cooled condenser is apt to be affected by the fluctuating ambient condition, some difficulties are brought to the use of a steam feeding water pump in an air-cooled unit. This paper introduces a new design of for steam feeding the water pump of an air-cooled unit using the back-pressure steam turbine as the prime motor. Using variable condition analysis on a 600 MW direct air-cooled unit, and with consideration of the effect on the ambient conditions, the feasibility, economy, and adaptability of the design are verified.

太阳能-空气源热泵牧草干燥系统制热性能研究

以太阳能-空气源热泵牧草干燥系统为研究对象,通过系统不同工作模式的温升、恒温制热试验及带载试验,分析了温升速率、单位温升能耗、COP及除湿效率。研究结果表明:联合制热模式与太阳能单独制热相比,单位温升耗电量降低了86.2%,温升速率提高了99~112倍。联合制热模式与热泵单独制热试验相比,在温升过程中温升速率降低了7.7%~17.6%,单位温升耗电量降低8.0%;在恒温制热过程中,前者COP比后者提高了6.5%~11.1%,耗电量降低了5.8%~10.7%;在升温制热过程中前者COP比后者提高了6.0%~10.4%,耗电量降低了6.6%~11.1%。联合干燥模式比热泵单独干燥模式的SMER值高19.8%~36.2%。

严寒地区空气源热泵耦合电磁能系统模拟运行研究

目的 为了促进空气源热泵耦合电磁能供热系统在严寒地区住宅建筑中的应用,研究该系统的运行性能和稳定性。方法 以沈阳地区某住宅建筑为例,应用Trnsys软件建立了空气源热泵耦合电磁能供热系统仿真模型,并用实测值对模型进行了验证;深入探讨空气源热泵耦合电磁能供热系统在供热期的运行特点,并与空气源热泵和电磁能供热系统分别进行比较。结果 空气源热泵耦合电磁能供热系统模型可靠,相对误差可以控制在15%以内;在供热期,室内平均温度可保持在17.97~21.84℃;空气源热泵耦合电磁能供热系统比电磁能供热系统的COP提高了59.17%,空气源热泵耦合电磁能供热系统CO_(2)减排量比空气源热泵和电磁能供热系统分别提高1.47%和59.50%。结论 空气源热泵耦合电磁能供热系统运行和COP变化更为稳定,系统环境效益更佳,室内热舒适性更高。

基于ANFIS的太阳能-空气源热泵供暖系统温度控制研究

针对太阳能-空气源热泵供暖系统运行环境复杂多变,模糊控制器的设计高度依赖人工经验的问题,提出一种基于自适应神经模糊推理系统(ANFIS)改进的模糊控制方法。该方法利用ANFIS在复杂系统建模中的优势,结合供暖系统温度响应特性和实际运行数据,建立联合供暖系统变工况ANFIS模型,生成与系统性能适配的模糊规则库并传递给模糊控制器执行。Matlab/Simulink仿真对比试验表明,与单一的模糊控制相比,该方法的控制精度提高了17.65%,调节时间缩短了36.4%,具有更高的控制精度和响应速度。

先进抽水压缩空气复合储能技术

储能技术的创新突破成为带动全球能源格局革命性、颠覆性调整的必经之路,是实现“碳中和、碳达峰”目标的重要举措。为此,西安交通大学“先进物理储能技术”研究团队创新性地发明了新型抽水压缩空气复合储能技术。该技术采用空气和水作为混合工作介质,利用水力机械设备和空气透平作为系统的复合做功设备,实现储能介质高效等温压缩/膨胀。相比于传统压缩空气储能技术,新型气液复合空气储能技术具有响应快、效率高、投资成本低等优点。团队通过10余年的攻关研究,完成了关键设备与储能系统的性能表征、时域特性研究、流体机械关键共性技术集中攻关、空气储能技术全寿命周期性能评估软件的研发及应用,研究成果可为气液复合压缩空气储能技术的规模化推广应用提供坚实的理论与数据支撑。

具有防融霜装置的蒸发器结霜特性及性能仿真研究

以具有防融霜装置的蒸发器为研究对象,建立基于理想最小防融霜补热量和结霜量无量纲关联式的空气源热泵动态模型,并依据实验数据验证其精确性,通过数值模拟分析不同环境参数对具有防融霜装置的蒸发器性能的影响。结果表明:后置式与跨越式系统蒸发器换热系数要高于前置式与传统电辅热系统,霜层厚度更小,分布更均匀;当相对湿度一定时,蒸发器换热系数随温度升高而增大;当空气温度不变时,换热系数随相对湿度的下降而减小,霜层更均匀;温度对蒸发器换热系数的影响比相对湿度更大。