Performance analysis of heat pump based on a new solar air-source heat pump heating system

To further improve the utilization efficiency of solar energy and the performance of solar heat pump heating systems,a new heating mode of a solar air-source heat pump（SASHP）is proposed,and the characteristics and performance of the heat pump part of this new heating system are studied.Based on a SASHP with 10 kW,the mathematical model of this system is built,and the characteristics and performance are concluded from the simulation analysis at different environmental temperatures and output water temperatures.The results show that the performance of heat pumps can be greatly improved based on the new SASHP.When the environmental temperature is 7 ℃,the coefficient of performance（COP）of the air-source heat pump（ASHP）can be increased by 26% at most.This paper sets up a base for further study on the heating system with this new SASHP in the heating season.

Analysis of Power Quality Problems in Large-Scale Application of Air-Source Heat Pump

With the implementation of electric energy alternatives,the large-scale application of electric energy substitution represented by air-source heat pumps has replaced traditional coal-fired heating,which is beneficial for the environment and alleviates air pollution.However,the large-scale application of airsource heat pumps has brought power quality problems such as voltage sags,harmonic pollution,and three-phase imbalance to the distribution network.This paper studies the fixed-frequency and variablefrequency air-source heat pump,introduces its working principle,analyzes the mechanism of its power quality problem.Moreover,the paper establishes a simulation model for the fixed-frequency heat pump and variable-frequency heat pump to connect to the distribution network.This research mainly studies the impact of large-scale fixed-frequency heat pumps on the depth of voltage sags in the distribution network and the impact of large-scale variable-frequency heat pumps on the harmonic content of the distribution network under different penetration rates and uses measured data to verify the reliability of the simulation results.This paper uses experimental data for the first time to verify the real power quality problems of large-scale heat pumps,which can provide a reference for determining the power quality standards for heat pumps connected to the power grid.At the same time,it can also provide a reference for the power quality management of the distribution network that is actually connected to electric heating.

Novel Radiation-Adjustable Heating Terminal Based on Flat Heat Pipe Combined with Air Source Heat Pump

The electrification of building heating is an effective way to meet the global carbon target. As a clean and sustainable electrified heating technology, air-source heat pumps (ASHPs) are widely used in areas lacking central heating. However, as a major component of space heating, heating terminals might not fit well with ASHP in order to achieve both intermittency and comfort. Therefore, this study proposes a novel radiation-adjustable heating terminal combined with an ASHP to achieve electrification, intermittency, and better thermal comfort. Radiant terminals currently suffer from three major problems: limited maximum heating capacity, inability to freely adapt, and difficulty with combining them with ASHPs. These problems were solved by improving the structural design of the novel terminal (Improvement A–E). Results showed that the maximum heating capacity increased by 23.6% and radiation heat transfer ratio from 10.1% to 30.9% was provided for users with the novel terminal. Further, new flat heat pipe (FHP) design improved stability (compressor oil return), intermittency (refrigerant thermal inertia), and safety (refrigerant leakage risk) by reducing the length of exposed refrigerant pipes. Furthermore, a new phased operation strategy was proposed for the novel terminal, and the adjustability of the terminal was improved. The results can be used as reference information for decarbonizing buildings by electrifying heating terminals.

The noise spectral characteristics and noise reduction schemes of screw air-source heat pump:A case study

The screw air-source heat pump can cause incessant high noise levels during operation,which might hinder adoption of this energy-efficient heat pump.First,acoustic measurements and comparison testing were performed in this research.The measurements revealed that the compressor is the main noise source of the heat pump,and it shows a multipeak frequency distribution and a wide frequency spectrum under different work conditions,with multiple peaks at 63,250,and 1000 Hz.Then,a compressor sound insulation cover with broadband absorption was proposed,and it was experimentally proven that the insulation cover can reduce the maximum sound pressure level of one unit from 89.8 dBA to 79.1 dBA.Third,we proposed several noise reduction strategies and compared their noise reduction effects using computer simulation.The results showed that the noise problem can be effectively improved through the rational design of the sound barrier and the layout and opening options of heat pump.The distance between the sound barrier and heat pump and the sound attenuation due to diffraction ALa exhibit a U-shaped relation.For buildings of different heights,the optimal heights of noise barrier are proposed.The 5.5-meter is the optimal height of the sound barrier for single-story buildings.The conclusions can be applied to other building projects for heat pump noise reduction.

Refrigerant Control Strategies for Residential Air-Conditioning and Heat-Pump System

This paper simulated the optimal refrigerant charge inventory of a refrigeration system in air-conditioning operation and heat-pump operation respectively,and studied the refrigerant control strategies in this system.The void fraction in two-phase fluid region was calculated by Harms model.And based on distributed parameter model and Harms model,the refrigerant charge inventory in condenser and evaporator were calculated and analyzed in air-conditioning conditions and heat-pump conditions,respectively.The calculating results of different refrigerant mass between refrigeration and heating conditions indicate that the optimal refrigerant charge inventory in heat-pump conditions is lower than that in air-conditioning conditions.To avoid the decrease of COP due to the surplus refrigerant in heating conditions,we introduced the liquid reservoir control method and associate capillary control method.Both of them could increase the heating capacity of the air-source heat pump.The difference of optimal refrigerant charge inventory in air-conditioning and heat-pump system can be controlled by the liquid reservoir or the associate capillary.