Hydrodynamics and Mass Transfer in a Modified Three-phase Airlift Loop Reactor

A modified internal-loop airlif reactor （MIALR） with a continuous slurry phase was studied to investigate the local hydrodynamic characteristics, including gas holdup, bubble size, bubble rise velocity and local mass transfer properties. Based on the analysis of geometrical construction and fluid properties of gas and slurry, MIALR was divided into six flow regions. In these flow regions, the local hydrodynamic characteristics were investigated over a wide range of operating variables. Furthermore, a new method was developed to measure the dissolved oxygen concentration. The volumetric mass-transfer coefficient in six flow regions was also calculated for comparison.

Treatment of Dimethoate Aqueous Solution by Using Ultrasonic Airlift Loop Reactor

Ultrasonic airlift loop reactor （UALR） shows potential and wide application for wastewater treatment. In this paper the performance and efficiency of UALR in dimethoate degradation were presented. The effects of O3 flow rate, ultrasonic intensity and initial concentration of dimethoate on degradation rate were investigated. UALR imposed a synergistic effect combining sonochemical merit with high O3 transfer rate. The results showed that UALR not only increased degradation rate, but also was better than the simole sum of degradation by O3 and ultrasound separately. Under the operation conditions of O3 flow of 0.34 m^3·h^-1, ultrasonic intensity 3.71 W.cm^-2, and initial concentration of dimethoate at 20 mg·L^- 1, the degradation rate of dimethoate increased to 80%. UALR seems an advisable choice for treating organic wastewater and this process may have wide application prospect in industry.

HYDRODYNAMIC STUDIES ON LOOP REACTORS (Ⅱ) AIRLIFT LOOP REACTORS

Hydrodynamics of airlift loop reactors was studied in detail experimentally andtheoretically.An internal airlift loop reactor was designed and set up for this study.An instru-mentation system based on the electrochemical method was adapted to measure local gas holdup andliquid velocity.A two-dimensional two-fluid model based on the first principles was established andimplemented to model the flow in airlift loop reactors.A corrected turbulent model was incorporatedin the simulation.The shear rate,shear stress and energy dissipation are evaluated from the flowfield.The numerically predicted results and experimental data obtained from this work as well as thesereported in literature are analyzed and compared.

Epoxidation of Cyclohexene with Oxygen in Ultrasound Airlift Loop Reactor

Epoxidation of cyclohexene to cyclohexene oxide was studied in a new type reactor—the ultrasound airlift loop reactor. The influences of ultrasound intensity, molar ratio of isobutyraldehyde to cyclohexene and oxy-gen gas flow rate on the conversion of cyclohexene and selectivity of cyclohexene oxide were investigated and dis-cussed, and the optimal operation condition was found, under which 95.2% conversion of cyclohexene and 90.7% selectivity of cyclohexene oxide were achieved. The ultrasonic airlift loop reactor utilizes the synergistic effect of sonochemsitry and higher oxygen transfer rate. Possible reaction mechanisms were outlined and the reason of ul-trasound promotion of epoxidation reactionwas analyzed.

Hydrodynamics and bubble behaviour in a three-phase two-stage internal loop airlift reactor

Local hydrodynamics of a gas–liquid–solid system,such as bubble circulation regime,gas holdup,liquid velocity and axial profile of solid concentration,are studied in a two-stage internal loop airlift reactor.Empirical correlations for gas holdup and liquid velocity are proposed to ease the reactor design and scale-up.Different bubble circulation regimes were displayed in the first(lower) and second(upper) stages.Increasing superficial gas velocity and solid loading can promote regime transition of the second stage,and the gas holdup of the second stage is higher than that of the lower stage.In addition,the effects of solid loading on bubble behaviour are experimentally investigated for each stage.It is found that bubble size in the downcomer decreases with the presence of solid particles,and bubble size distribution widens under higher superficial gas velocity and lower solid loading.

Analysis and Measurement of Mass Transfer in Airlift Loop Reactors

Inter-phase mass transfer is important to the design and performance of airlift loop reactors for either chemical or biochemical applications, and a good measurement technique is crucial for studying mass transfer in multiphase systems. According to the model of macro-scale mass transfer in airlift loop reactors, it was proved that the airlift loop reactor can be regarded as a continuous stirred tank reactor for measuring mass transfer coefficient. The calculated mass transfer coefficient on such a basis is different from the volumetric mass transfer coefficient in the macro-scale model and the difference is discussed. To describe the time delay of the probe response to the change of oxygen concentration in the liquid phase, a model taking into account the time constant of response is es-tablished. Sensitivity analysis shows that this model can be used to measure the volumetric mass transfer coefficient. Applying this model to the measurement of volumetric mass transfer coefficient in the loop reactor, results that co-incide with the turbulence theory in the literate were obtained.

Experimental and Numerical Study of Gas-Liquid Flow in a Sectionalized External-Loop Airlift Reactor

The external loop airlift reactor(ELALR)is widely used for gasliquid reactions.It’s advantage of good heat and mass transfer rates compared to conventional bubble column reactors.In the case of fermentation application where a medium is highly viscous and coalescing in nature,internal in riser helps in the improvement of the interfacial area as well as in the reduction of liquidphase back mixing.The computational fluid dynamic(CFD)as a tool is used to design and scaleup of sectionalized external loop airlift reactor.The present work deals with computational fluid dynamics(CFD)techniques and experimental measurement of a gas holdup,liquid circulation velocity,liquid axial velocity,Sauter mean bubble diameter over a broad range of superficial gas velocity 0.0024≤UG≤0.0168 m s 1.The correlation has been made for bubble size distribution with specific power consumption for different plate configurations.The effects of an internal on different mass transfer models have been completed to assess their suitability.The predicted local mass transfer coefficient has been found higher in the sectionalized external loop airlift reactor than the conventional ELALR.

Oilfield produced water treatment in internal-loop airlift reactor using electrocoagulation/flotation technique

Oilfield produced water is large quantities of salty water trapped in underground formations and subsisted under high temperatures and pressures that are brought to the surface along with oil during production. Produced water(PW) contains a lot of pollutants such as hydrocarbons and metals, this water must be treated before disposal. Therefore, different techniques are being used to treat produced water. Electrocoagulation is an efficient treatment technique involving the dissolution of anodes and formation of electro-coagulants, while the simultaneous generation of H_2 bubbles at the cathode leads to the pollutant removal by flotation. Electrocoagulation(EC)method is one of the most promising and widely used processes to treat oilfield produced water. In the present work, a conventional internal-loop(draught tube) airlift reactor was utilized as electrocoagulation/flotation cell for PW treatment by inserting two aluminum electrodes in the riser section of the airlift reactor. The EC airlift reactor was operated in a batch mode for the liquid phase. Different experimental parameters were studied on the oil and turbidity removal efficiencies such as current density, initial pH, electrocoagulation time, and air injection.The experimental results showed that mixing of the oil droplets in the PW was accomplished using only the liquid recirculation resulted by H_2 microbubbles generated by EC process which enhanced the oil removal. The experimental results further showed that the EC time required achieving ≥ 90% oil removal efficiency decreases from 46 to 15 min when operating current density increases from 6.8 to 45.5 mA·cm^(-2). This reactor type was found to be highly efficient and less energy consuming compared to conventional existing electrochemical cells which used mechanical agitation.

Influences of top clearance and liquid throughput on the performances of an external loop airlift slurry reactor integrated mixing and separation

A new developed external loop airlift slurry reactor, which was integrated with gas–liquid–solid three-phase mixing, mass transfer, and liquid–solid separation simultaneously, was deemed to be a promising slurry reactor due to its prominent advantages such as achieving continuous separation of clear liquid from slurry and cyclic utilization of solid particles without any extra energy, energy-saving, and intrinsic safety design. The principal operating parameters, including gas separator volume, handling capacity, and superficial gas velocity, are systematically investigated here to promote the capabilities of mixing, mass transfer, and yield in the pilot external loop airlift slurry reactor. The influences of top clearance and throughput of the clear liquid on flow regime and gas holdup in the riser, liquid circulating velocity, and volumetric mass transfer coefficient with a typical high solid holdup and free of particles are examined experimentally. It was found that increasing the gas separator volume could promote the liquid circulating velocity by about 14.0% at most. Increasing the handling capacity of the clear liquid from 0.9 m3·h-1 to 3.0 m3·h-1 not only could increase the output without any adverse consequences, but also could enhance the liquid circulating velocity as much as 97.3%. Typical operating conditions investigated here can provide some necessary data and guidelines for this new external loop airlift slurry reactor to upgrade its performances.

The Preparation of 2-Chloro-5-chloromethylpyridine in an Airlift Loop Reactor

A new process for the direct chlorination of 2-chloro-5-methylpyridine to yield 2-chloro-5-chloro-methylpyridine in an airlift loop reactor (ALR) has been studied. Five main reaction conditions including TR, na/ns, cp, Qg and dD/dR were optimized. The average molar yield and purity of 2-chloro-5-chloromethylpyridine obtained were 79% and 98.5% respectively under the optimum operating conditions. Finally, the efficiency for the preparation of 2-chloro-5-chloromethylpyridine with ALR and stirred tank reactor (STR) respectively was compared.

CFD Simulation of Scale Influence on the Hydrodynamics of an Internal Loop Airlift Reactor

In this work, the overall gas hold-up in the riser and down-comer of three internal airlift reactors with a working volume of 10.5, 32 and 200 l at the range of temperatures 18℃ - 21℃, under atmospheric pressure was simulated using Com-putational Fluid Dynamics (CFD). The range of superficial gas velocity was 0.5 - 3 cm/s. The three reactors geometrically were similar to each other. CFD simulation and experimental data showed that the gas hold-up in the riser and down-comer increased by increasing the reactor scale. It was concluded that the simulated data were in good agreement with the experimental ones obtained from the literature.

Modeling of Continuous Cross-flow Microfiltration Process in an Airlift External-loop Slurry Reactor

New modified combination mathematical models including the pores blocking models and the cake layer models were developed to describe the continuous cross-flow microfiltration in an airlift external loop slurry reactor. The pores blocking models were created based on the standard blocking law and the intermediate blocking law, and then the cake layer models were developed based on the hydrodynamic theory in which the calculation method of porosity of cake layer was newly corrected. The Air-Water-FCC equilibrium catalysts cold model experiment was used to verify the relevant models.Results showed that the calculated values fitted well with experimental data with a relative error of less than 10%.

Flow mixing model of liquid phase in an internal airlift loop reactor

Residence time distribution (RTD) analysis of liquid phase was conducted in an internal airlift loop reactor (AL) and a bubble column (BC) with the tracer response technique. These data were simulated and compared through several flow mixing models. The modeling results of two-parameter model indicated that there were higher ratio of full mixing zones and lower ratio of bypass flow in AL than in BC. Then a completely mixed-plug flow parallel combined (four-parameter) model was established. Modeling results show that it is more precise and more obvious than two-parameter model.

GLS-MALR中的气含率和循环液速

在1个四流道的气-液-固三相多室气升式环流反应器(MALR)中,以空气-水-K树脂为体系,考察了气体表观速率、固体装载量对气含率和循环液速的影响。结果表明,上升室的气含率随着该室气体表观速率的增加而增加,而随着另一上升室气体表观速率的增加而略有降低;下降室的气含率随着该室气体表观速率的增大而略有增加;上升室和下降室的气含率均随固体装载量的增加而降低;循环液速随着上升室气体表观速率的增加而增加,而随着固体装载量的增加而降低。在鼓泡流下,用关联式法建立了上升室的气含率模型;根据动量平衡原理建立了循环液速模型。气含率和循环液速的计算值和实验值的平均相对误差分别为±5.755%和±9.362%。

氨氮对UASB-ALR工艺处理晚期垃圾渗滤液的抑制性研究

采用升流式厌氧污泥层反应器(UASB)-气升式环流反应器(ALR)的组合工艺处理高氨氮垃圾渗滤液。稳定运行阶段,通过添加氯化铵,考察NH4+-N浓度对UASB-ALR工艺稳定运行的影响。结果表明,当UASB进水氨氮浓度超过2 660mg/L时,UASB的有机物去除率下降到60%。当ALR进水中NH4+-N浓度达到3140 mg/L时,ALR对COD和NH4+-N去除率分别下降到12.8%和57%。经过7 d的恢复期,UASB对COD的去除率回升到78.5%,ALR反应器的COD及NH4+-N去除率均无法恢复到抑制前的水平。

IC-ALR工艺处理去油脂泔水实验

采用IC-ALR的新型工艺处理含有大量蛋白质、碳水化合物的去油脂泔水。结果表明，在适应期采用快速提升负荷的方式有利于提高污泥的活性，加速污泥颗粒化；稳定运行期，当进水有机浓度达到22.4 g/L时，COD去除率高达91.7％，出水中9.2～10.1 mmol/L的VFA含量不会影响IC 的稳定运行。利用ALR处理IC厌氧消化液，当进水COD和NH3-N浓度分别达到1850和420 mg/L时，ALR反应器能够去除进水中75％的COD和91％的氨氮，出水COD和NH3-N浓度分别为420和40 mg/L。

Hydrodynamic Behaviour of a Gas-Solid Air-loop Stripper

In this paper, the principles of airlift loop reactor in gas-liquid and gas-liquid-solid systems are extended to gas-solid system. The models on bed average voidage in draft tube and the particle circulation velocity in a gas-solid loop reactor are deduced. The experiments are also conducted on a Φ600mm×7000mm reactor. The catalyst voidage and catalyst circulation velocity are measured at different radial and axial positions in draft tube and annulus, respectively. The experimental data are analyzed systemically and represented satisfactorily by the proposed models.

Process Intensification in Pneumatically Agitated Slurry Reactors

Pneumatically agitated slurry reactors,including bubble column reactors and airlift loop reactors(ALRs),are important gas-liquid-solid multiphase reactors.These reactors have been widely applied in many processes,especially in the biological fermentation and energy chemical industry,due to their low shear stress,good mixing,perfect mass-/heat-transfer properties,and relatively low costs.To further improve the performance of slurry reactors(i.e.,mixing and mass/heat transfer)and to satisfy industrial require-ments(e.g.,temperature control,reduction of back-mixing,and product separation),the process intensi-fication of slurry reactors is essential.This article starts by reviewing the latest advancements in the intensification of mixing and mass/heat transfer in these two types of reactors.It then summarizes process-intensification methods for mixing and separation that allow continuous production in these slurry reactors.Process-intensification technology that integrates directional flow in an ALR with simple solid-liquid separation in a hydrocyclone is recommended for its high efficiency and low costs.This arti-cle also systematically addresses vital considerations and challenges,including flow regime discrimina-tion,gas spargers,solid particle effects,and other concerns in slurry reactors.It introduces the progress of numerical simulation using computational fluid dynamics(CFD)for the rational design of slurry reactors and discusses difficulties in modeling.Finally,it presents conclusions and perspectives on the design of industrial slurry reactors.

Influences of fluid physical properties,solid particles,and operating conditions on the hydrodynamics in slurry reactors

Slurry reactors are popular in many industrial processes,involved with numerous chemical and biological mixtures,solid particles with different concentrations and properties,and a wide range of operating conditions.These factors can significantly affect the hydrodynamic in the slurry reactors,having remarkable effects on the design,scale-up,and operation of the slurry reactors.This article reviews the influences of fluid physical properties,solid particles,and operating conditions on the hydrodynamics in slurry reactors.Firstly,the influence of fluid properties,including the density and viscosity of the individual liquid and gas phases and the interfacial tension,has been reviewed.Secondly,the solid particle properties(i.e.,concentration,density,size,wettability,and shape)on the hydrodynamics have been discussed in detail,and some vital but often ignored features,especially the influences of particle wettability and shape,as well as the variation of surface tension because of solid concentration alteration,are highlighted in this work.Thirdly,the variations of physical properties of fluids,hydrodynamics,and bubble behavior resulted from the temperature and pressure variations are also summarized,and the indirect influences of pressure on viscosity and surface tension are addressed systematically.Finally,conclusions and perspectives of these notable influences on the design and scale-up of industrial slurry reactors are presented.

三相MALR中气、固含率研究

在一个内径17cm,高100cm;内置壁厚0.7cm的十字隔板制成的多室气升式环流反应器（MALR）中,一室表观气速在0.2545~1.018cm.s-1、三室表观气速在0.2545~3.8173cm.s-1范围内,研究了空气-水-K树脂颗粒（颗粒当量直径1.5±0.2mm、密度为1.0316g.cm-3）的三相物系中两个上升室表观气速对4个室的气含率、固含率的影响。结果表明,某一上升室的气含率随着该室气速的增加而增加,该室的固含率却随着该室气速的增加而下降;某一上升室的气含率和固含率均与另一上升室的气速无关;下降室气含率、固含率只与其前一级上升室气速有关,与下一级上升室气速无关。