Highly selective extraction of aromatics from aliphatics by using metal chloride-based ionic liquids

The separation of aromatics from aliphatics is essential for achieving maximum exploitation of oil resources in the petrochemical industry.In this study,a series of metal chloride-based ionic liquids were prepared and their performances in the separation of 1,2,3,4-tetrahydronaphthalene(tetralin)/dodecane and tetralin/decalin systems were studied.Among these ionic liquids,1-ethyl-3-methylimidazolium tetrachloroferrate([EMIM][FeCl_(4)])with the highest selectivity was used as the extractant.Density functional theory calculations showed that[EMIM][FeCl_(4)]interacted more strongly with tetralin than with dodecane and decalin.Energy decomposition analysis of[EMIM][FeCl_(4)]-tetralin indicated that electrostatics and dispersion played essential roles,and induction cannot be neglected.The van der Waals forces was a main effect in[EMIM][FeCl_(4)]-tetralin by independent gradient model analysis.The tetralin distribution coefficient and selectivity were 0.8 and 110,respectively,with 10%(mol)tetralin in the initial tetralin/dodecane system,and 0.67 and 19.5,respectively,with 10%(mol)tetralin in the initial tetralin/decalin system.The selectivity increased with decreasing alkyl chain length of the extractant.The influence of the extraction temperature,extractant dosage,and initial concentrations of the system components on the separation performance were studied.Recycling experiments showed that the regenerated[EMIM][FeCl_(4)]could be used repeatedly.

Hyperbranched polymer hollow-fiber-composite membranes for pervaporation separation of aromatic/aliphatic hydrocarbon mixtures

The separation of aromatic/aliphatic hydrocarbon mixtures is crucial in the petrochemical industry.Pervaporation is regarded as a promising approach for the separation of aromatic compounds from alkanes. Developing membrane materials with efficient separation performance is still the main task since the membrane should provide chemical stability, high permeation flux, and selectivity. In this study, the hyperbranched polymer(HBP) was deposited on the outer surface of a polyvinylidene fluoride(PVDF)hollow-fiber ultrafiltration membrane by a facile dip-coating method. The dip-coating rate, HBP concentration, and thermal cross-linking temperature were regulated to optimize the membrane structure.The obtained HBP/PVDF hollow-fiber-composite membrane had a good separation performance for aromatic/aliphatic hydrocarbon mixtures. For the 50%/50%(mass) toluene/n-heptane mixture, the permeation flux of optimized composite membranes could reach 1766 g·m^(-2)·h^(-1), with a separation factor of 4.1 at 60℃. Therefore, the HBP/PVDF hollow-fiber-composite membrane has great application prospects in the pervaporation separation of aromatic/aliphatic hydrocarbon mixtures.

Preparation and characterization of biodegradable aliphatic-aromatic copolyesters/nano-SiO_2 hybrids via in situ melt polycondensation

In situ melt polycondensation was proposed to prepare biodegradable aliphatic-aromatic copolyesters/nano-SiO2 hybrids based on terephthalic acid （TPA）, poly（L-lactic acid） oligomer （OLLA）, 1,4-butanediol （BDO） and nano-SiO2. TEM and FT-IR characterizations confirmed that TPA, OLLA and BDO copolymerized to obtain biodegradable copolyesters, poly（butylene terepbthalate-co-lactate） （PBTL）, and the abundant hydroxyl groups on the surface of nano-SiO2 provided potential sites for in situ grafting with the simultaneous resulted PBTL. The nano-SiO2 particles were chemically wrapped with PBTL to form PBTL/nano- SiO2 hybrids. Due to the good dispersion and interfacial adhesion of nano-SiO2 particles with the copolyester matrix, the tensile strength and the Young＇s modulus increased from 5.4 and 5.6 MPa for neat PBTL to 16 and 390 MPa for PBTL/nano-SiO2 hybrids with 5 wt.% nano-SiO2, respectively. The mechanical properties of PBTL/nano-SiO2 hybrids were substantially improved.

Study on Structure and Crystallinity of A New Biodegradable Aliphatic-Aromatic Copolyester

A series of biodegradable aliphatic-aromatic copolyesters, poly(butylene terephthalate-co-butylene adipate-co- ethylene terephthalate-co-ethylene adipate) (PBATE), were synthesized from terephthalic acid (PTA), adipic acid (AA), 1,4-butanediol (BG) and ethylene glycol (EG) through direct esterification and polycondensation. The sequence structure and crystallinity of the copolyester were investigated by 1H NMR spectroscopy and the wide-angle X-ray diffractometry (WAXD). The analytical results showed that the PBATE copolyester was a random copolymer and the composition of PBATE copolyester was almost consistent with the feed molar ratios. The crystal structure of PBATE copolyester belonged to the triclinic crystalline system; The variation in melting point of the synthesized PBATE copolyester agreed well with the estimation obtained by the Flory equation and was applicable to the random copolymer.

BIODEGRADABLE ALIPHATIC/AROMATIC COPOLYESTERS BASED ON TEREPHTHALIC ACID AND POLY(L-LACTIC ACID):SYNTHESIS,CHARACTERIZATION AND HYDROLYTIC DEGRADATION

Biodegradable aliphatic/aromatic copolyesters, poly（butylene terephthalate-co-lactate） （PBTL） were prepared via direct melt polycondensation of terephthalic acid （TPA）, 1,4-butanediol （BDO） and poly（L-lactic acid） oligomer （OLLA）. The effects of polymerization time and temperature, as well as aliphatic/aromatic moiety ratio on the physical and thermal properties were investigated. The largest molecular weight of the copolyesters was up to 64100 with molecular weight distribution index of 2.09 when the polycondensation was carried out at 230℃ for 6 h. DSC, XRD, DMA and TGA analysis clearly indicated that the degree of crystallinity, glass-transition temperature, melting point, decomposition temperature, tensile strength, elongation and Young＇s modulus were influenced by the ratio between TPA and OLLA in the final copolyesters. Hydrolytic degradation results demonstrated that the incorporation of biodegradable lactate moieties into the aromatic polyester could efficiently improve hydrolytic degradability of the copolymer even though it still had many aromatic units in the main chains.

SYNTHESIS OF AN EPOXY-TERMINATED HYPERBRANCHED AROMATIC POLYESTER

An epoxy-terminated hyperbranched aromatic polyester (P3) was synthesized from a hyperbranched aromatic polyester containing carboxylic acid end groups (P1), which was derived from the condensation polymerization of the AB(2) monomer, 5-acetoxyisophthalic acid. Polymer P1 was converted into the polymeric acid chloride by reaction with thionyl chloride. The acid chloride was reacted with ethanol and glycidol to form a poly(ethyl ester) (P2) and an epoxy terminated material (P3), respectively. The reaction conditions in each step of these processes had to be controlled very carefully to avoid unwanted cross-linking reactions. The characterization of products and intermediates, including molecular weight distributions and thermal properties, are reported.

Membrane materials in the pervaporation separation of aromatic/aliphatic hydrocarbon mixtures—A review

The separation of aromatic/aliphatic hydrocarbon mixtures is a significant process in chemical industry, but challenged in some cases. Compared with conventional separation technologies, pervaporation is quite promising in terms of its economical, energy-saving, and eco-friendly advantages. However, this technique has not been used in industry for separating aromatic/aliphatic mixtures yet. One of the main reasons is that the separation performance of existed pervaporation membranes is unsatisfactory. Membrane material is an important factor that affects the separation performance. This review provides an overview on the advances in studying membrane materials for the pervaporation separation of aromatic/aliphatic mixtures over the past decade. Explored pristine polymers and their hybrid materials(as hybrid membranes) are summarized to highlight their nature and separation performance. We anticipate that this review could provide some guidance in the development of new materials for the aromatic/aliphatic pervaporation separation.

Synthesis and characterization of biodegradable aliphatic polyesters using dibutylmagnesium as initiator

Aliphatic polyesters were synthesized via the ring opening polymerization of the corresponding lactones initiated with dibutylmagnesium both in bulk and in solution. The resulting polymers were characterized by 1H, 13C NMR, GPC and XRD. The results indicated that dibutylmagnesium is an effective initiator for the ring opening polymerization of lactones.

MORPHOLOGY OF A THERMOTROPIC AROMATIC POLYESTER

The crystalline morphology of a thermotropic aromatic polyester has been studied by microscopy techniques. Spherulites with ringed structure under polarizing micioscope were observed for solution cast specimens, They were composed of radially growing crystalline lamellae of thickness around 100. It was found that the molecules were packed in the thickness direction. Banded texture was observed in randomly packed domains for melt cast specimens. The bands have the same width and internal structure as those usually observed in oriented specimens of these polymers obtained by shearing their mesomorphic melt.

Synthesis and characterization of new polyesters based on 2,5-bis[(4-chloro carboxyanilino)carbonyl]pyridine and aromatic diols

Six new polyesters 7a-f were synthesized through the solution polycondensation reaction of diacid chloride 5 with six aromatic diols 6a-f in N,N-dimethyl acetamide(DMAc) as solvent in the presence of pyridine as base.The polycondensation reaction produced a series of novel polyester containing pyridyl moiety in the main chain in high yields with inherent viscosities between 0.35 and 0.54 dL/g.The resulted polymers were fully characterized by means of FT-IR spectroscopy,elemental analyses,inherent viscosity ...

FOURIER TRANSFORM INFRARED STUDY OF FRACTIONATED AROMATIC POLYESTERS

Infrared spectra at different temperatures have been studied for fractions ofa liquid crystal tormmg aromatic polyester. The molecular interactions in different phases and their changes duringthe transitions were discussed. Abrupt frequency shift was found for bands of groups both in mesogens and flexible spacers during fusion and isotropization transitions. It may imply that both the mesogens and the flexible spacers are included in the same crystalline phase and give their contributions to the formation of the mesophase. The splitting into doublet of the C—O stretching vibrations was observed for both the aromatic and aliphatic esters and was attributed to the existence of local regions for ester groups different in ordering. The more ordered regions do not disappear completely even in the isotropic liquid phase.

THE GAS TRANSPORT BEHAVIOR IN AROMATIC POLYESTER MEMBRANES

Six aromatic polyesters were prepared for gas separation membranes, and their permeation properties for hydrogen, oxygen, nitrogen, carbon dioxide, and methane were measured at 30 degrees C and 1 atmosphere by low pressure manometric method. The correlation between the gas transport behavior and molecular structure of aromatic polyester membrane is discussed. These data are interpreted qualitatively in terms of the calculated packing density, gas-polymer interaction, concentration of aryl bromine on backbone, and effect of silane group on main chain of polymer.

THE EFFECT OF SUBSTITUENT ON THE THERMAL PROPERTIES OF POLYESTERS CONSISTING OF AROMATIC TYPE SCHIFF BASE MESOGENIC UNITS AND POLYMETHYLENE SPACERS

Polyesters consisting of substituted aromatic type Schiff base mesogenic unit andpolymethylene spacers were synthesized and their thermal transitions and liquid crystallineproperties were studied. The liquid crystalline behaviour has been characterized by differentialscanning calorimetry (DSC) and optical polarizing microscopy. Structural broadening bysubstitution of methoxy group in 2, 2' positions of the mesogenic core produce polymers withlower transition temperatures. Polymers synthesized from ortho and meta substituted phenylenediamine did not form a liquid crystal phase.

CRYSTALLINE MORPHOLOGY IN A SERIES OF CH_(3)-SUBSTITUTED THERMOTROPIC AROMATIC POLYESTERS WITH EVEN AND ODD FLEXIBLE SPACERS

Crystalline morphology in a series of CH_(3)-substituted main chain thermotropic aromatic polyesters with even and odd numbered methylene spacers has been studied by polarizing optical microscopy(POM),scanning electron microscopy(SEM)and transmission electron microscopy(TEM).On crystallization from solution evaporation spherulites of radial structure were observed in the polymers with even numbered spacers,but spherulites with concentric rings form in the polymer with odd numbered spacers.Both spherulites have a lamellar structure,which is about 10 nm in thickness.On crystallization from nematic glassy state spherulites can not be grown;lamellar structure was only observed around disclinations in a specimen during crystallization.Ln the case of crystallization from nematic melt two types of spherulites can be observed far the sample with even numbered spacers.For the sample with add numbered spacers spherulites can not be formed,but only irregular crystallites.

Effect of the Structure of Cations and Anions of Ionic Liquids on Separation of Aromatics from Hydrocarbon Mixtures

The effects of the structure of typical cations and anions of ionic liquids on the separation of benzene and toluene from aromatic/paraffin mixtures were studied. The .results showed that the corresponding separation factors were considerably larger than those of the traditional solvents （Benzene＋Hexane＋sulfolane）, and that the ionic liquids could be used as novel solvents for the separation of aromatics from hydrocarbon mixtures. The key parameters governing the ability of ionic liquids for separating aromatics from hydrocarbon sources were investigated. It was found that the effectiveness of the ionic liquids, based on the same anion, changed in the cation order of [BIqu]^＋〈 [BPy]^＋〈 [BMIM]^＋. The selectivity of the ionic liquid toward aromatics decreased apparently with the increasing length of the substituted alkyl chain of its cationic head ring. The separation factors, based on the same cation, changed in the anion order of [Tf2N]^-〈[PF6]^-〈[BF4]^-〈[C2H5SO4]^-. The solubilities of the aromatics were greater in the ionic liquids based on the former three anions than that in the ionic liquids involving [C2H5SO4]^-.

Removal of Hydrophobic Organic Contaminants from Aqueous Solutions by Sorption onto Biodegradable Polyesters

Sorption by biodegradable polyesters of several aromatic chemicals as model compounds for hydrophobic organic contaminants (HOCs) was studied. The biodegradable polyesters used were poly(butylene succinate), poly(3-hydroxybutyrate-co-3-hydroxyvalerate), poly(ε-caprolactone), poly(butylene succinate/ terephthalate), and poly(L-lactic acid). Petrochemical plastics, low-density polyethylene and polyethylene terephtalate, were used for comparison. The target HOCs were biphenyl, bisphenol-A, dibenzofuran, diethylstilbestrol, nonyl-phenol, and chlorophenols. The treatment of the HOC solutions with each of the biodegradable polyesters resulted in the nearly complete removal of the chemicals by sorption from the aqueous phase, except for the case of poly(L-lactic acid). Low-density polyethylene adsorbed biphenyl and dibenzofuran selectively, and polyethylene terephtalate did not adsorb any of the HOCs. The adsorptive interaction between the plastics and the HOCs might be related to both the glass transition temperature of the former and the nature of the latter as defined by the Fujita's inorganicity/organicity ratio. The toxic effect of 3,5-dichlorophenol on bacte-rial growth in liquid culture was removed by the addition of a biodegradable polyester. These results provide a basis for the applicability of the biodegradable plastics as the adsorbents for the removal of HOCs from aquatic environments.

Polyisocyanuratoesters:Renewable Linear Polyesters with High Flame Retardancy

Biobased urea nowadays attracts increasing attention as a biomass resource with giant potential,which benefits from the development of biobased ammonia and ecological sanitation system.Urea is an ideal feedstock for chemical industry and developing new urea-based polymer materials can take advantage of the urea resource.In this work,a class of renewable linear polyesters,namely polyisocyanuratoesters(PICEs)were synthesized from a urea-based monomer bis(2-carbomethoxyethyl)isocyanurate and biobased aliphatic diols.Compared with conventional aliphatic polyesters,PICEs containing isocyanurate rings in the polymer chain backbone exhibit outstanding flame retardancy that both PICE-4(the number‘4’refers to the number of methylene in diols,e.g.4 for butylene and 6 for hexylene)and PICE-6 have high limiting oxygen index values over 30%.In the UL 94 tests,PICE-6 reaches V-1 rating;while V-2 is found for PICE-10.All PICEs exhibit similar pyrolysis behavior that the temperatures of 5%weight loss are around 320°C.PICEs are found to have glass transition among 20°C-45°C.No crystallization behavior is observed without annealing except for PICE-10,which can crystallize even at room temperature.

Computational Study for the Aromatic Nucleophilic Substitution Reaction on 1-Dimethylamino-2,4-bis(trifluoroacetyl)-naphthalene with Amines

Our previous research showed that aliphatic amines were put in order of high reactivity as “ethylamine > ammonia > t-butylamine > diethylamine” on the aromatic nucleophilic substitution of 1-dimetylamino-2,4-bis(trifluoroacetyl)-naphthalene 1 in acetonitrile. The DFT calculation study (B3LYP/6-31G* with solvation model) for the reactions of 1 with above four amines rationally explained the difference of each amines reactivity based on the energies of their Meisenheimer complexes 3 which are assumed to formed as the reaction intermediates in the course of the reaction giving the corresponding N-N exchange products 2. Intramolecular hydrogen bond between amino proton in 1-amino group and carbonyl oxygen in 2-trifluoroacetyl group stabilizes Meisenheimer complexes 3 effectively, and accelerates the substitution reaction from 1 to 2. Our calculation results also predicted that the above order of amines is also true if less polar toluene is used as a solvent instead of acetonitrile even though more enhanced conditions are required.

生物降解高分子材料阻燃改性研究进展

为了探讨生物降解高分子材料阻燃改性研究进展情况,梳理了近年来化学合成的生物降解高分子类材料阻燃性研究的文献,重点综述了聚丁二酸丁二醇酯和聚乳酸的阻燃改性研究情况。聚丁二酸丁二醇酯的阻燃改性方法主要分为含磷复合协效阻燃体系和添加生物质阻燃剂两类,聚乳酸的阻燃改性方法主要分为磷系阻燃体系、磷-氮协同阻燃体系、膨胀型阻燃体系和添加生物质阻燃剂等。通过总结和分析各阻燃方法的发展状况,认为:含磷有机化合物或者磷-氮协同型阻燃剂仍然是行之有效且普遍采用的阻燃添加剂,但是这些物质的存在对于生物降解性必然产生负面影响。因此,应强化全生物质阻燃体系的构建及其应用,重点平衡阻燃性、生物降解性与加工-应用性能之间的关系,以推动生物降解高分子材料的绿色阻燃技术发展和应用。

生物基半芳香族共聚酰胺PA5T/56与脂肪族聚酰胺PA56的性能对比

生物基聚酰胺PA56凭借其绿色低碳的原料来源以及与商业化PA66相近的综合性能而受到关注,但受限于脂肪族的柔性主链结构,无法满足高温场景下的使用需求。为解决上述问题,引入对苯二甲酸构筑生物基半芳香族共聚酰胺PA5T/56,对PA5T/56的结构及性能进行系统研究,并与生物基脂肪族聚酰胺PA56进行对比分析。红外光谱与核磁共振氢谱的表征结果验证了PA5T/56与PA56结构上的差异;相比PA56,PA5T/56具有更高的玻璃化转变温度(t_(g)=113℃)、更优的热稳定性(t_(d,5%)=392℃,t_(dmax)=423℃),以及更佳的热机械性能,同时其在高温下具有适宜加工的熔体黏度(<10^(3)Pa·s),这些优势赋予生物基半芳香族PA5T/56广阔的应用前景。