A novel approach for one-step forming ε-caprolactam from cyclohexane nitrozation catalyzed by transition metal salt

The nitrozation reaction of cyclohexane in one-step reaction to form ε-caprolactam has been studied using transition metal salt as catalysts in this work. The results indicated that the catalysts play an especially important role. This method is expected to be a novel way to synthesize other lactam by similar reaction. The possible mechanism was suggested.

Transformation of alkali and alkaline-earth metals during coal oxy-fuel combustion in the presence of SO_2 and H_2O

The occurrence modes of alkali and alkaline-earth metals（AAEMs） in coal relate to their release behavior and ash formation during combustion. To better understand the transformation of AAEMs,the release behavior of water-soluble,HCl-soluble,HCl-insoluble AAEMs during Shenmu coal（SM coal） oxy-fuel combustion in the presence of SO2 and H2O in a drop-tube reactor was investigated through serial dissolution using H2O and HCl solutions. The results show that the release rates of AAEMs increase with an increase in temperature under the three atmospheres studied. The high release rates of Mg and Ca from SM coal are dependent on the high content of soluble Mg and Ca in SM coal. SO2 inhibits the release rates of AAEMs,while H2O promotes them. The effects of SO2 and H2O on the Na and K species are more evident than those on Mg and Ca species. All three types of AAEMs in coal can volatilize in the gas phase during coal combustion. The W-type AAEMs release excessively,whereas the release rates of I-type AAEMs are relatively lower. Different types of AAEM may interconvert through different pathways under certain conditions. Both SO2 and H2O promote the transformation reactions. The effect of SO2 was related to sulfate formation and the promotion by H2O occurs because of a decrease in the melting point of the solid as well as the reaction of H2O.

Additive effects of alkaline-earth metals and nickel on the performance of Co/γ-Al_2O_3 in methane catalytic partial oxidation

Nano-sized γ-alumina （γ-Al2O3） was first prepared by a precipitation method. Then, active component of cobalt and a series of alkaline- earth metal promoters or nickel （Ni） with different contents were loaded on the γ-Al2O3 support. The catalysts were characterized by N2 adsorption-desorption, X-ray diffraction （XRD） and thermogravimetry analysis （TGA）. The activity and selectivity of the catalysts in catalytic partial oxidation （CPO） of methane have been compared with Co/γ-Al2O3, and it is found that the catalytic activity, selectivity, and stability are enhanced by the addition of alkaline-earth metals and nickel. The optimal loadings of strontium （Sr） and Ni were 6 and 4 wt%, respectively. This finding will be helpful in designing the trimetallic Co-Ni-Sr/γ-Al2O3 catalysts with high performance in CPO of methane

Recent Advances of Transition Metal Basic Salts for Electrocatalytic Oxygen Evolution Reaction and Overall Water Electrolysis

Electrocatalytic oxygen evolution reaction(OER)has been recognized as the bottleneck of overall water splitting,which is a promising approach for sustainable production of H_(2).Transition metal(TM)hydroxides are the most conventional and classical non-noble metal-based electrocatalysts for OER,while TM basic salts[M^(2+)(OH)_(2-x)(A_(m^(-))_(x/m),A=CO_(3)^(2−),NO_(3)^(−),F^(−),Cl^(−)]consisting of OH−and another anion have drawn extensive research interest due to its higher catalytic activity in the past decade.In this review,we summarize the recent advances of TM basic salts and their application in OER and further overall water splitting.We categorize TM basic salt-based OER pre-catalysts into four types(CO_(3)^(2−),NO_(3)^(−),F^(−),Cl^(−)according to the anion,which is a key factor for their outstanding performance towards OER.We highlight experimental and theoretical methods for understanding the structure evolution during OER and the effect of anion on catalytic performance.To develop bifunctional TM basic salts as catalyst for the practical electrolysis application,we also review the present strategies for enhancing its hydrogen evolution reaction activity and thereby improving its overall water splitting performance.Finally,we conclude this review with a summary and perspective about the remaining challenges and future opportunities of TM basic salts as catalysts for water electrolysis.

A review on liquid metals as cathodes for molten salt/oxide electrolysis

Compared with solid metals,liquid metals are considered more promising cathodes for molten slat/oxide electrolysis due to their fascinating advantages,which include strong depolarization effect,strong alloying effect,excellent selective separation,and low operating temperature.In this review,we briefly introduce the properties of the liquid metal cathodes and their selection rules,and then summarize development in liquid metal cathodes for molten salt electrolysis,specifically the extraction of Ti and separation of actinides and rare-earth metals in halide melts.We also review recent attractive progress in the preparation of liquid Ti alloys via molten oxide electrolysis by using liquid metal cathodes.Problems related to high-quality alloy production and large-scale applications are cited,and several research directions to further improve the quality of alloys are also discussed to realize the industrial applications of liquid metal cathodes.

Thermodynamic analysis on the direct preparation of metallic vanadium from NaVO_3 by molten salt electrolysis

A novel and environmentally friendly route to directly prepare metallic vanadium from NaV03 by molten salt electrolysis is proposed. The feasibility about the direct electro-reduction of NaV03 to metallic vanadi- um is analyzed based on the thermodynamic calculations and experimental verifications. The theoretical decomposition voltage of NaV03 to metallic vanadium is only 0.47 V at 800 ℃ and much lower than that of the alkali and alkali earth metal chloride salts. The value is slightly higher than that of low-valence vanadium oxides such as V203, V305 and VO. However, the low-valence vanadium oxides can he further electro-reduced to metallic vanadium thermodynamically. The thermodynamic analysis is verified by the experimental results. The direct preparation of metallic vanadium from NaV03 by molten salt electrolysis is feasible.

Characteristics and Nature of Metal Fog in Molten Salts

In this paper are reported the characteristics and nature of metal fog in molten cryolite-alumina mixtures on the basis of laboratory experiments and quantum chemistry studies.The metal fog is the finely divided metal particles in the molten salts, and it dissolves partly in the molten cryolite to form atomic clusters,such as(Al_nNa_m)^(x+) type.

Separation of chitin from shrimp shells enabled by transition metal salt aqueous solution and ionic liquid

Chitin is a widely used important industrial polymer mainly from shrimp shells, but its commercial preparation is under the great challenge of serious pollution due to the requirement of HCl and Na OH.Herein, we demonstrated that high purity chitin can be obtained from waste shrimp shells(WSSs) by cascade separation with transition metal salt aqueous solution and ionic liquid(IL). Firstly, calcium carbonate of WSSs was effectively removed in the metal salt aqueous solution driven by the ion exchange interaction. Subsequently, 1-butyl-3-methylimidazolium chloride([Bmim]Cl) had bifunctional abilities to remove residual protein and introduced metal salts simultaneously by hydrogen bonding and coordination interactions. The key experimental factors affecting the separation process were systematically studied, including the type of metal salts, temperature, and [Bmim]Cl loading. After sequential treatment with a 20%(mass) Ni SO4aqueous solution at 130 ℃ and [Bmim]Cl at 150 ℃, the purity of a-chitin can be up to 96.5%(mass) that meets commercial requirements. The use of metal salts with higher coordination ability makes the preparation of chitin no longer depend on the commonly acid-base reaction, which is conducive to the preservation of chitin structure.

Evaluation of properties of concrete using fluosilicate salts and metal (Ni,W) compounds

To improve watertightness and antibiosis of sewage structure concrete, the antimicrobial watertight admixture was made with fluosilicate salts and antimicrobial compounds. And fresh properties, watertightness, harmlessness and antibiosis of concrete were investigated experimentally. As a result, the fresh properties of concrete were similar to those of an ordinary concrete, without setting time delay. Compressive strength and carbonation resistance of concrete were better than those of an ordinary concrete. Finally it was confirmed that the antimicrobial watertight admixture of concrete had an antibiosis inhibiting SOB growth.

Synthesis of cyclic carbonates from epoxides or olefins and CO_2 catalyzed by metal-organic frameworks and quaternary ammonium salts

Catalytic properties of the metal-organic framework Cr-MIL-101 in solvent-free cycloaddition of CO2 to epoxides to produce cyclic carbon- ates using tetrabutylammonium bromide as co-catalyst have been explored under mild reaction conditions （8 bar CO2, 25 ~C）. Styrene and propylene carbonates were formed with high yields （95% and 82%, respectively）. Catalytic performance of Cr-MIL-101 was compared with other MOFs： Fe-MIL-101, Zn-MOF-5 and HKUST-1, The catalytic properties of different quaternary ammonium bromides, Cr-MIL-101 as well as PW12/Cr-MIL-101 composite material have been assessed in oxidative carboxylation of styrene in the presence of both tert-butyl hydroperoxide and H202 as oxidants at 8-100bar CO2 and 25-80 ~C with selectivity to styrene carbonate up to 44% at 57% substrate conversion.

Synthesis and Selective Coloration of Monoaza Crown Ethers Bearing Picrylamino-type Side Arms for Alkali Metal Salts and Methylamine

N-pivot lariat ethers with picrylamino group as a chromophore (1, 2 and 3) have been prepared by reaction of N-(4-aminoaryl)monoaza crown ethers with picryl chrolide, and the selective coloration of 1, 2 and 3 for alkali metal salts and amines has been studied by UV-Vis spectra.

Concentrated dual-salt electrolytes for improving the cycling stability of lithium metal anodes

Lithium（Li） metal is an ideal anode material for rechargeable Li batteries, due to its high theoretical specific capacity（3860 mAh/g）, low density（0.534 g/cm3）, and low negative electrochemical potential（-3.040 V vs. standard hydrogen electrode）. In this work, the concentrated electrolytes with dual salts, composed of Li[N（SO2F）2]（Li FSI） and Li[N（SO2CF3）2]（Li TFSI） were studied. In this dual-salt system, the capacity retention can even be maintained at 95.7%after 100 cycles in Li｜Li FePO4 cells. A Li｜Li cell can be cycled at 0.5 mA/cm2 for more than 600 h, and a Li｜Cu cell can be cycled at 0.5 m A/cm2 for more than 200 cycles with a high average Coulombi efficiency of 99%. These results show that the concentrated dual-salt electrolytes exhibit superior electrochemical performance and would be a promising candidate for application in rechargeable Li batteries.

The Influence of Nitrate Salts and Complex Metal Ion to Regio-Selective Synthesis of 2-Nitro-5,10,15,20-Tetra- (4-Methoxyphenyl)Porphyrinato Metal

A series of 2\|nitro\|5,10,15,20\|tetra(4\|methoxyphenyl) porphyrinato metals were regioselectively synthesized with nitrate salts as nitrating reagent in acetic acid/acetic anhydride for preparation of 2\|substituted porphyrin. The influence of nitrate salts and complex metal ion to the reaction were investigated. The extent of 2\|nitration increased with the electronegativity of the central metal. When Cu(NO 3 ) 2 · 3H 2O was used as nitrating reagent, almost quantitative yields of 2\|nitro porphyrin were obtained in the case of Cu(Ⅱ) or Ni(Ⅱ) chelates, while Zn(Ⅱ) or Mn(Ⅲ) chelates gave 50% and 30% yields respectively. If Zn(NO 3 ) 2 ·10H 2 O was used as nitrating agent, no product was found for Cu(Ⅱ) or Ni(Ⅱ) chelates, 12% was found for Zn(Ⅱ) chelates. The other metal ion and nitrate salts were also found in quite different influence.

Blue-emissions Modulated by Packing Forces in Alkaline-earth Metal OrganicFrameworks Based on Thiophene-2,5-dicarboxylic: Structures and Theoretical Calculations

Solvothermal reactions of Ca(NO), Sr(NO)with thiophene-2,5-dicarboxylic in DMF afforded two new inorganic-organic hybrid frameworks, [M(TDC)(DMF)]n(M = Ca(1), Sr(2), TDC = thiophene-2,5-dicarboxylic, DMF = N,N?-dimethylformamide), which have been characterized by single-crystal X-ray diffraction, powder X-ray diffraction, elemental analysis and IR spectra. Both compounds feature three-dimensional(3D) frameworks based on the versatile coordinated modes(μ-η~2:η~2, μ-η~2:η~1, μ-η~2:η~1) of carboxylic groups in tdc ligands. C–H···S hydrogen bonds and C–H···π interactions contribute to the stabilization of the structures. They exhibit weaker packing force compared with their literature isomers. Consequently, blue and blue/green luminescence of two compounds has been observed. Their luminescence mechanism can be ascribed to ligand-to-metal charge transfer(LMCT) compared with the ligand-centered luminescence in their isomers. Electronic structural calculations illustrate that under the condition of weaker packing forces, larger gaps can be achieved, which facilitate the LMCT. This work suggests that the introduction of S-heteroatom can result in more electrons rich in the metal centers, thus giving rise to metal-involved luminescence.

Ultrasonically Assisted Regioselective Nitration of Aromatic Compounds in Presence of Certain Group V and VI Metal Salts

Ultrasonically assisted nitration reactions (USANR) with anilides, moderately activated and non-activated aromatic compounds underwent smoothly and afforded good yields of products with high regio selectivity. Observed longer reaction times (6 - 8 hrs.) in metal catalyzed reactions reduced to (1 - 2 hrs.) under sonication. When ortho position is blocked para derivatives are obtained, and ortho nitro products are obtained when para position is blocked. In case of USANR of aromatic carbonyl and related compounds the effect of sonication is much more effective. The reactions could be completed only in few minutes.

Applying ellipsometry to studying the effect of two kinds of rare earth metal salts on anodizing aluminum alloy

The effects of rare earth metal salts (REMs), cerium(IV) salt and lanthanum (III) salt, on the property of anodized coating of LD10 aluminum alloy are studied by corrosion tests including neutral salt spray test and copper accelerated acetic acid immersion test, polarization curves measurement, energy dispersion analyzer of X-Ray(EDAX) analysis, and in situ ellipsometry. The results show that the addition of either of the two REMs in anodizing solution hardly changes the composition of an anodized coating, while increases the thickness of barrier part and reduces the porosity of porous part, which contributed to the improvement of the corrosion resistance of the anodized coating. The results also demonstrate that the effect of cerium salt was better than that of lanthanum salt.

The Negative Effect of Heavy Metal Salts on the Body of Mammal Animals

The main purpose of this presented article was to explain the need to study the amount of heavy metal salts in the environment where animals live, in the water, in air, and in the food and fodder consumed. This article presents materials from the literature on the effects of heavy metal salts on the body of animals and the environment in which they live. The cited analytical data showed that the general information on the negative effects of heavy metal salts on the body is sufficient, but their effects on the digestive tract and morpho-functional properties of rabbits should be studied in depth. Therefore, we planned to focus our scientific work on this topic. The article mainly refers to salts of heavy metals cadmium, lead, and mercury (Cd, Pb, Hg). It is noted in the literature that heavy metal salts have a negative effect on the body of animals. We focused mainly on data on the effects of heavy metals on farm animals, including rabbits. But it is clear that the authors referred to were referring to experimental animals. These negative effects are manifested in the form of disorders of digestive functions, disorders of neurovegetative processes, increasing incidence of cardiovascular disease, rapid heart failure, deterioration of calcium metabolism, as well as impaired haemoglobin metabolism. Disorders of protein metabolism manifest themselves in the form of cases of hyperproteinaemia and dysproteinaemia. The results of the evaluation of the organism of healthy animals in chemically and radioactively contaminated areas showed the accumulation of significant levels of chemical elements in their organism. We mainly looked at the effects of heavy metal salts on farm animals. The cited analytical data showed that the general information on the negative effects of heavy metal salts on the body is sufficient, but the effects on the activity of organ systems in the body (respiration, blood and blood circulation, digestion, reproduction, productivity and immunological systems) have not been comprehensively studied.

Nonmetal-Metal Transition in Solutions of Metals in Molten Salts

Solutions of metals in molten salts present a rich phenomenology: localisatlon of electrons in disordered ionic media, activated electron transport increasing with metal concentration towards a nonmetal-metal (NM-M) transition, and liquid-liquid phase separation. A brief review of progress in the study of these systems is given in this article, with main focus on the NM-M transition. After recalling the known NM-M behaviour of the component elements in the case of expanded fluid alkali metals and mercury and of solid halogens under pressure, the article focuses on liquid metal-molten salt solutions and traces the different NM-M behaviours of the alkalis in their halides and of metals added to polyvalent metal halides.

Reversion of Bioluminescent Bacteria (Mutatox^(TM)) toTheir Luminescent State upon Exposure to OrganicCompounds, Munitions, and Metal Salts

Mutatox is a new genotoxicity bioassay which uses as the endpoint the bioluminescence produced on reversion of a dark strain of the marine bacterium Vibrio fischeri ±S9.Reversion can occur by several mechanisms, including base substitution, frame-shift, SOS induction, and DNA intercalation. For screening, Mutatox provides many advantages over the Salmonella trphimurium (Ames) assay: it requires minimal sterility, employs a shorter incubation period, and does not require culture maintenance. Eighteen organic chemicals (phenol, polynuclear aromatic hydrocarbons, nitrotoluenes, others), Na3PO4, and 4 genotoxic metals (Cu2+, Ni2+, As3+, Cd2+) were tested. Most of the organic compounds positive in S. typhimurium assays were positive in Mutatox. None of the metals was genotoxic in V. fischeri, possibly due to poor uptake from the saline medium