Towards 640 Gbit/s wavelength conversion based on nonlinear polarization rotation in a semiconductor optical amplifier

Taking into account ultra-fast carrier dynamics, this paper models 640 Gbit/s wavelength conversion scheme based on nonlinear polarization rotation （NPR） in a single semiconductor optical amplifier （SOA） and investigates the performance of this kind of wavelength conversion scheme in detail. In this model, two carrier temperature equations are introduced to substitute two energy density equations, which reduce the complexity of calculation in comparison with the previous model. The temporary gain and phase shift dynamics induced by ultra-short optical pulses are numerically simulated and the simulated results are qualitatively in good agreement with reported experimental results. Simulated results show that non-inverted and inverted 640 Gbit/s wavelength conversions based on NPR are achieved with clear open eye diagrams. To further investigate the performance of the non-inverted wavelength conversion scheme, the dependence of output extinction ratio （ER） on some key parameters used in simulation is illustrated. Furthermore, simulated analyses show that high performance non-inverted wavelength conversion based on NPR can be achieved by using a red-shifted filtering scheme.

Performance analysis of optical burst switching node with limited wavelength conversion capabilities

The systematical and scalable frameworks were provided for estimating the blocking probabilities under asynchronous traffic in optical burst switching(OBS) nodes with limited wavelength conversion capability(LWCC) . The relevant system architectures of limited range and limited number of wavelength converters(WCs) deployed by a share-per-fiber(SPF) mode were developed,and the novel theoretical analysis of node blocking probability was derived by combining the calculation of discouraged arrival rate in a birth-death process and two-dimensional Markov chain model of SPF. The simulation results on single node performance verify the accuracy and effectiveness of the analysis models. Under most scenarios,it is difficult to distinguish the plots generated by the analysis and simulation. As the conversion degree increases,the accuracy of the analysis model worsens slightly. However,the utmost error on burst loss probability is far less than one order of magnitude and hence,still allows for an accurate estimate. Some results are of actual significance to the construction of next-generation commercial OBS backbones.

Optical properties of wavelength-tunable green-emitting color conversion glass ceramics

Color conversion glass ceramics are prepared by cosintering borosilicate glass frits and green 0.06Ce：Y2.94（Al1-xGax）5O12 phosphors. The crystal structures, the influence of Ga concentration on the photoluminescence （PL）, and reliability properties of the color conversion glass ceramics are investigated. The PL emission wavelengths of 0.06Ce：Y2.94（Al1-xGax）5O12 glass ceramics show blue shift from 545 nm to 525 nm with increasing Ga content （x value） under excited at 460 nm. Reliability test results show that the quantum yield （QY） of 0.06Ce：Y2.94（Al1-xGax）5O12 glass ceramics decreases from 70.60% to 59.06% with x value increasing from 0.15 to 0.35 under the ambient condition of 85℃/RH85% for the exposure time of 168 h. And the quantum yield （QY） of 0.06Ce：Y2.94（Al1-xGax）5O12 glass ceramics decreases from 65.13% to 52.23% after being soaked into boiled water for 4 h. The finding reveals that the addition of Ga can deteriorate the reliability of the color conversion glass ceramics.

A High Efficiency Wavelength Conversion Scheme Based on Four Wave Minxing in a Semiconductor Optical Amplifier

A new approach of all optical wavelength converter based on four wave mixing (FWM) in a semiconductor optical amplifier (SOA) with the conjugate wave reflected by a fiber Bragg grating (FBG) and then amplified by the SOA is reported. By adjusting the pump power, the conversion efficiency could be improved 7～10dB with signal to background noise ratio (SBR) deteriorated 1～2dB, compared with traditional single pump four wave mixing.

Broad-Band All-Optical Wavelength Conversion of Differential Phase-Shift Keyed Signal Using an SOA-Based Nonlinear Polarization Switch

Broad-band all-optical wavelength conversion of differential phase-shift keyed （DPSK） signal is experimentally demonstrated. This scheme is composed of a one-bit delay interferometer demodulation stage followed by a semiconductor optical amplifier （SOA） based nonlinear polarization switch. A wavelength converter for the 10 G b/s DPSK signal is presented, which has a wide wavelength range of more than 30 nm. The converted signals experience small power penalties less than 1.4 dB compared with the original signal, at a bit error rate of 10-9. Additionally, the optical spectra, the measured waveforms and the open eye diagrams of the converted signals show a high quality wavelength conversion performance.

Bee Colony Optimization Algorithm for Routing and Wavelength Assignment Based on Directional Guidance in Satellite Optical Networks

With the development of satellite communication,in order to solve the problems of shortage of on-board resources and refinement of delay requirements to improve the communication performance of satellite optical networks,this paper proposes a bee colony optimization algorithm for routing and wavelength assignment based on directional guidance(DBCO-RWA)in satellite optical networks.In D-BCORWA,directional guidance based on relative position and link load is defined,and then the link cost function in the path search stage is established based on the directional guidance factor.Finally,feasible solutions are expanded in the global optimization stage.The wavelength utilization,communication success probability,blocking rate,communication hops and convergence characteristic are simulated.The results show that the performance of the proposed algorithm is improved compared with existing algorithms.

Mode Conversion and Diffraction of Guided Optical Waves from Magnetostatic Waves under Inclined Bias Magnetic Field

The noncollinear interaction of guided optical waves with magnetostatic waves under inclined bias magnetic field is theoretically studied in detail. Similar approach can also be applied to the collinear interaction. Calculation results indicate that the diffraction efficiency (DE) in magnitude is equal to the mode-conversion efficiency (MCE) under vertical bias magnetic field, but they differ greatly under inclined bias magnetic field. By comparison to the case of vertical magnetization, the DE or the MCE can be greatly increased under inclined magnetic field. The characteristic of the DE curves obtained is basically in agreement with the experimental result.

Realizing mode conversion and optical diode effect by coupling photonic crystal waveguides with cavity

We propose a novel two-dimensional photonic crystal structure consisting of two line defect waveguides and a cavity to realize mode conversion based on the coupling effect. The W1/cavity/W2 structure breaks the spatial symmetry and successfully converts the even（odd） mode to the odd（even） mode in the W2 waveguide during the forward（backward）transmission. When considering the incidence of only the even mode, the optical diode effect emerges and achieves approximate 35 d B unidirectionality at the resonant frequency. Moreover, owing to the narrow bandpass feature and the flexibility of the tuning cavity, utilization of the proposed structure as a wavelength filter is demonstrated in a device with a Y-branch splitter. Here, we provide a heuristic design for a mode converter, optical diode, and wavelength filter derived from the coupling effect between a cavity and adjacent waveguides, and expect that the proposed structure can be applied as a building block in future all-optical integrated circuits.

Optical temperature sensor based on up-conversion fluorescence emission in Yb^(3+):Er^(3+) co-doped ceramics glass

yb^3＋：Er^3＋ co-doped oxy-fluoride ceramics glass has been prepared. The mechanism of up-conversion emissions about Er^3＋ was discussed, and the temperature properties of green up-conversion fluorescence between 303 and 823 K were investigated. The results show that the sensitivity of this sample reaches its maximum value, about 0.0047 K^-1, when the temperature is 383 K, indicating that this kind of sample can be used as high temperature and high sensitivity optical temperature sensor.

Optical Analog-to-digital Conversion Scheme Based on Tunable Fabry-Perot Resonator

Proposed is an interference type of optical analog-to-digital conversion(ADC). The refractive index of Fabry-Perot cavity changes with different voltages. The Fabry-Perot resonator converts electronic intensity into light wavelength through selecting lights of different wavelengthes. The parameters of the scheme are acquired with the transmission matrix of optical element and the time of steady-state light field. The maximum sampling speedes of 4-bit, 6-bit, 7-bit, 8-bit and 9-bit(ADC) are 1.695×1010 count/s, 4.33×109 count/s, 2.38×109 count/s, 1.24×109 count/s and 5.9×108 count/s, respectively.

Transmission Performance of the Optical Millimeter-wave Up-conversion Link Using a Phase Modulator

Numerically analyzed is the transmission performance of the optical millimeter(mm)-wave generated by frequency up-conversion via a phase modulator along the dispersive fiber.60 GHz mm-wave sub-carrier(SC)signals can be obtained after fiber transmission,simultaneously,the phase-modulated signals can be converted to the intensity-modulated ones.The numerical results show that the optical mm-wave at fading loops has better performance,and the eye diagram still keeps open when optical mm-wave signal is transmitted over 98 km.

Strip silicon waveguide for code synchronization in all-optical analog-to-digital conversion based on a lumped time-delay compensation scheme

An all-optical analog-to-digital converter （ADC） based on the nonlinear effect in a silicon waveguide is a promising candidate for overcoming the limitation of electronic devices and is suitable for photonic integration. In this paper, a lumped time-delay compensation scheme with 2-bit quantization resolution is proposed. A strip silicon waveguide is designed and used to compensate for the entire time-delays of the optical pulses after a soliton self-frequency shift （SSFS） module within a wavelength range of 1550 nm-1580 nm. A dispersion coefficient as high as -19800 ps/（km.nm） with ＋0.5 ps/（km.nm） variation is predicted for the strip waveguide. The simulation results show that the maximum supportable sampling rate （MSSR） is 50.45 GSa/s with full width at half maximum （FWHM） variation less than 2.52 ps, along with the 2-bit effective- number-of-bit and Gray code output.

Effect of radiation-induced mean wavelength shift in optical fibers on the scale factor of an interferometric fiber optic gyroscope at a wavelength of 1300 nm

In order to analyze the effect of wavelength-dependent radiation-induced attenuation （RIA） on the mean trans- mission wavelength in optical fiber and the scale factor of interferometric fiber optic gyroscopes （IFOGs）, three types of polarization-maintaining （PM） fibers are tested by using a 60Co γ-radiation source. The observed different mean wave- length shift （MWS） behaviors for different fibers are interpreted by color-center theory involving dose rate-dependent absorption bands in ultraviolet and visible ranges and total dose-dependent near-infrared absorption bands. To evaluate the mean wavelength variation in a fiber coil and the induced scale factor change for space-borne IFOGs under low radiation doses in a space environment, the influence of dose rate on the mean wavelength is investigated by testing four germanium （Ge） doped fibers and two germanium-phosphorus （Ge-P） codoped fibers irradiated at different dose rates. Experimental results indicate that the Ge-doped fibers show the least mean wavelength shift during irradiation and their mean wavelength of optical signal transmission in fibers will shift to a shorter wavelength in a low-dose-rate radiation environment. Finally, the change in the scale factor of IFOG resulting from the mean wavelength shift is estimated and tested, and it is found that the significant radiation-induced scale factor variation must be considered during the design of space-borne IFOGs.

Three-wavelength generation from cascaded wavelength conversion in monolithic periodically poled lithium niobate

Tunable coherent emission is generated in a single-pass, cascaded wavelength conversion process from mode-locked laser-pumped monolithic periodically poled lithium niobate（PPLN）. Three ranges of wavelength, including visible output from 628 nm to 639 nm, near-infrared output from 797 nm to 816 nm, and mid-infrared output from 3167 nm to 3459 nm,were obtained from the monolithic PPLN, which consists of a 10-mm section for 532-nm-pumped optical parametric generation（OPG） and a 7-mm section for 1064-nm-pumped sum frequency generation（SFG）. A pump-to-signal conversion efficiency of 23.4% for OPG at 50°C and a quantum efficiency of 26.2% for SFG at 200°C were obtained.

An Ant Colony Algorithm Based on Cross-Layer Design for Routing and Wavelength Assignment in Optical Satellite Networks

This paper introduces an ant colony routing and wavelength assignment algorithm based on cross-layer design(CL-ACRWA),which can overcome the adverse effects of Doppler wavelength shift on data transmission in optical satellite networks. Firstly, a cross-layer optimization model is built, which considers the Doppler wavelength shift, the transmission delay as well as wavelength-continuity constraint. Then an ant colony algorithm is utilized to solve the cross-layer optimization model, resulting in finding an optimal light path satisfying the above constraints for every connection request. The performance of CL-ACRWA is measured by the communication success probability, the convergence property and the transmission delay. Simulation results show that CL-ACRWA performs well in communication success probability and has good global search ability as well as fast convergence speed. Meanwhile, the transmission delay can meet the basic requirement of real-time transmission of business.

Magic Wavelength Measurement of the ^(87)Sr Optical Lattice Clock at NIM

We report on the magic wavelength measurement of our optical lattice clock based on fermion strontium atoms at the National Institute of Metrology （NIM）. A Ti：sapphire solid state laser locked to a reference cavity inside a temperature-stabilized vacuum chamber is employed to generate the optical lattice. The laser frequency is measured by an erbium fiber frequency comb. The trap depth is modulated by varying the lattice laser power via an acousto-optic modulator. We obtain the frequency shift coefficient at this lattice wavelength by measuring the diffbrential frequency shift of the clock transition of the strontium atoms at different trap depths, and the frequency shift coefficient at this lattice wavelength is obtained. We measure the frequency shift coefficients at different lattice frequencies around the magic wavelength and linearly fit the measurement data, and the magic wavelength is calculated to be 368554672（44）MHz.

A new distribution scheme of decryption keys used in optical verification system with multiple-wavelength information

A new distribution scheme of decryption keys used in optical verification systems is proposed. The encryption procedure is digitally implemented with the use of an iteration algorithm in computer. Three target images corresponding to three wavelengths are encoded into three sets of phase-only masks （POMs） by a special distributing method. These three sets of POMs are assigned to three authorized users as the personal identification. A lensless optical system is used as the verification system. In the verification procedure, every two of the three authorized users can pass the verification procedure cooperatively, but only one user cannot do. Numerical simulation shows that the proposed distribution scheme of decryption keys not only can improve the security level of verification system, but also can bring convenience and flexibility for authorized users.

Two-wavelength Lidar Measurement of Cloud-aerosol Optical Properties

Based on ullstability of inversion algorithms of the lidar equation caused by molecular scattering,a new algorithm to derive both the aerosol extinction to backscatter ratio and the extinchon coefficient profile is proposed in this paper.As shown in numerical experiments,in case of a ground-based lidar,the error in the aerosol optical depth solution can be less than 10%,and the error of < 6.7 in the aerosol exhnction to backscatter ratio can be obtained if the error in the lidar constant is<6%;and in the case of a spaceborne lidar,the present method can be ugh to determine the lidar constant at a short wavelength with an accuracy of being better than 1%.

Multi-functional optical fiber sensor system based on a dense wavelength division multiplexer

We propose a novel and efficient multi-functional optical fiber sensor system based on a dense wavelength division multiplexer(DWDM).This system consists of an optical fiber temperature sensor, an optical fiber strain sensor, and a 48-channel DWDM.This system can monitor temperature and strain changes at the same time.The ranges of these two sensors are from-20℃ to 100℃ and from-1000 με to 2000 με, respectively.The sensitivities of the temperature sensor and strain sensor are 0.03572 nm/℃ and 0.03808 nm/N, respectively.With the aid of a broadband source and spectrometer,different kinds and ranges of parameters in the environment can be monitored by using suitable sensors.